氯离子浓度对锌电积用铝基铅合金复合β-PbO2颗粒阳极行为的影响

在酸性硫酸锌体系中研究了不同氯离子含量对Al/Pb-0.3%Ag-0.06%Ca复合β-PbO₂颗粒阳极行为的影响, 并通过X射线衍射(XRD)以及扫描电子显微镜(SEM)等技术手段来表征阳极的特征。 结果表明, 随着氯离子含量的增加, 阳极的析氧过电位逐渐增大;阻抗呈逐渐增大的趋势;阳极表面膜β-PbO₂和α-PbO₂衍射峰强度整体呈现出减弱的趋势;阳极氧化膜上的枝状晶簇消失;腐蚀速率逐渐增大。 当氯离子含量为300 mg/L时, 阳极具有最大的表观电流密度i₀, 表现出了最好的电化学性能以及耐腐蚀性。     

铅锑合金在硫酸溶液中的阳极膜II.电位对阳极膜生长的影响

本文使用线性电位扫描法还原预恒电位法氧化形成的阳极膜,研究电位对Pb-7Sb,Pb-7Sb-0.3Ag和Pb-5Sb-0.2As三种合金在30℃,4.5MH2SO4溶液中的阳极膜的生长速度的影响,在铅锑合金中添加银可降低合金阳极膜的生长速度,但在高电位1.4V(vs.Hg2SO4电极时,Pb-7Sb-0.3Ag合金上的PbO2膜的生长速度在上述三合金中居首,这可能是由于在银上的氧析出超电势较低的缘故,本文讨论了这种阳极膜的生长机理。     

铅锑合金在硫酸溶液中的阳极膜-——Ⅱ.电位对阳极膜生长的影响

本文使用线性电位扫描法还原预恒电位法氧化形成的阳极膜,研究电位对Pb-7Sb,Pb-7Sb-0.3Ag和Pb-5Sb-0.2As三种合金在30℃,4.5MH_2SO_4溶液中的阳极膜的生长速度的影响。在铅锑合金中添加银可降低合金阳极膜的生长速度。但在高电位1.4V(vs.Hg_2SO_4电极)时,Pb-7Sb-0.3Ag合金上的PbO_2膜的生长速度在上述三合金中居首,这可能是由于在银上的氧析出超电势较低的缘故。本文还讨论了这种阳极膜的生长机理。     

不锈钢基/β-PbO2-TiO2-Co3O4复合镀层制备及其性能表征

使用直流复合电沉积方法制备不锈钢基β-PbO2、TiO2掺杂β-PbO2、Co3O4掺杂β-PbO2、TiO2和Co3O4共掺杂β-PbO2复合镀层材料.采用SEM、EDS、XRD和电化学测试等对复合电极进行形貌、成分、组成和催化活性表征,并且将不锈钢基/β-PbO2-TiO2-Co3O4电极应用到锌电积实验中.结果表明,添加Co3O4能提高PbO2电极的催化活性;添加TiO2可以起到细化晶粒,增大比表面积的作用;不锈钢基β-PbO2-TiO2-Co3O4复合镀层阳极与Pb-Ag合金阳极相比,锌电积槽电压降低为2.97V,电流效率提高到91.2％,使用寿命延长.     

两类不同阳极电氧化过程中的失活现象及氧化机制

利用电化学测试技术分析了两类不同阳极在电氧化降解对氯苯酚过程中的失活现象及氧化机制. 结果表明, 对氯苯酚在“I”类阳极Pt和“II”类阳极含氟树酯(polytetrafluoroethylene, PTFE)的β-PbO2 (PTFE-β-PbO2)上可发生直接氧化反应, 且两者的电催化活性均会在短时间内失活. 高电位电解能使失活的PTFE-β-PbO2和Pt得到再生, 但Pt电极需要更高的电解电位. 常见有机溶剂(如丙酮、四氢呋喃、二甲基亚砜)的浸洗可以再生失活的Pt电极, 但不能再生PTFE-β-PbO2电极. 对于“I”类阳极Pt, 当阳极电位大于2.0 V时, 除对氯苯酚的直接氧化反应外, 晶格氧的氧化作用成为整个降解过程的主导因素; 而对“II”类阳极PTFE-β-PbO2, 当阳极电位大于1.8 V时, 除直接氧化反应外, 羟基自由基的降解反应成为对氯苯酚去除的主要原因.     

β-PbO2/TiO2纳米管电极的制备及其电催化降解苯酚

采用阳极氧化法和脉冲电沉积制备出β-PbO2改性TiO2纳米管(β-PbO2/TiO2-NTs)电极,通过扫描电子显微镜(SEM)、X射线衍射(XRD)和X射线光电子能谱(XPS)等技术手段对制备的β-PbO2/TiO2-NTs电极的表面形貌和结构进行了表征。结果表明,该方法成功地将β-PbO2纳米颗粒分散在TiO2纳米管中,通过电催化降解苯酚评价了β-PbO2/TiO2-NTs电极的电催化活性,实验结果表明,在TiO2-NTs中电沉积β-PbO2提高了电极的电催化活性,对苯酚的降解达到83%。     

氟硼酸镀液二氧化铅电沉积

研究了在氟硼酸或其掺杂镀液中于Pt基底电沉积PbO2镀层的电化学和结构性质.循环伏安测试、XRD分析和SEM形貌观察表明,BF4-可提高二氧化铅电沉积速率;电沉积的PbO2晶型为β-PbO2;F-、Fe3+共掺杂影响晶体生长的择优取向及镀层形貌,电沉积的FB/F-Fe-PbO2镀层整齐致密;电沉积过程增大电流密度可改变生长晶面取向.     

交流电在Al2O3模板中沉积金属机理探讨

以铝阳极氧化形成有序的多孔氧化铝为模板,利用交流电在模板孔洞中沉积金属Ag得到纳米Ag粒子/Al2O3组装体系,透射电镜观察证实在氧化铝模板中有金属纳米Ag粒子存在.分析了交流电能在孔洞中沉积金属的原因是由于Al/Al2O3界面的整流特性,测量了Al/Al2O3界面的I－U关系曲线.     

交流电在Al_2O_3模板中沉积金属机理探讨

以铝阳极氧化形成有序的多孔氧化铝为模板,利用交流电在模板孔洞中沉积金属Ag得到纳米Ag粒子/Al2O3组装体系,透射电镜观察证实在氧化铝模板中有金属纳米Ag粒子存在.分析了交流电能在孔洞中沉积金属的原因是由于Al/Al2O3界面的整流特性,测量了Al/Al2O3界面的I－U关系曲线.     

电流密度对锌电积用Pb-Ag平板阳极电化学行为的影响(英文)

研究了在不同电流密度下进行长时间极化后Pb-Ag(0.8%(质量分数,w))平板阳极的阳极电位、腐蚀率及阳极钝化膜.同时,也研究了该阳极在ZnSO4-MnSO4-H2SO4电解液中的阴极电流效率和阴极锌品质.阳极钝化膜的表面形貌用扫描电镜(SEM)进行观测.实验结果表明,不管电解液中是否存在Mn2+,电流密度对阳极和阴极的电化学行为都产生了显著的影响.随着电流密度的升高,阳极电位、腐蚀率、阴极电流效率和阳极泥生成量也增加,而阴极锌中的Pb含量则减少.当电流密度从500A·m-2降到200A·m-2时,阳极在ZnSO4-MnSO4-H2SO4电解液中的稳定电位和腐蚀率分别减少64mV和40%.此外,在比较低的电流密度下,阳极电位更容易稳定,阳极表面生成的钝化膜更加致密并与基体结合牢固,这些都有利于降低阳极腐蚀率.为了降低阳极电位、减小阳极腐蚀率及阳极泥生成量并提高阴极电流效率和阳极锌品质,锌电积的理想工作条件是较低的阳极电流密度和较高的阴极电流密度.     

Effect of Sb on the properties of anodic Pb(Ⅱ) oxide film formed in alkaline solution

The composition and properties of the anodic films formed on Pb and Pb-3at.%Sb alloy at -0.10 V (vs. Hg/HgO) for 2.5 h in 0.1 mol.dm-3 NaOH solution (25℃) were investigated by cyclic voltammetry, linear sweep voltammetry, open circuit decay curve, photocurrent technique, X-ray diffraction (XRD) and scanning electron microscopy (SEM). It was found that the anodic film formed oh Pb mainly consists of t-PbO, while that on Pb-3at.%Sb consists of o-PbO, t-PbO and a small amount of orthorhombic Sb2O3. The dominant component of the film anodically grown on Pb-3at.%Sb for less than 5 min is o-PbO, however, t-PbO is the major component of the anodic film formed for 1 h or longer. It is established that Sb suppresses the growth of t-PbO. The anodic film formed on Pb-3at.%Sb is less porous than that on Pb. The bandgap energies of t-PbO and o-PbO in the films were determined by photocurrent measurements to be 1.83-1.84 eV and 2.60 eV, respectively.     

α-PbO纳米粉体的固相合成及其对MnO2电极材料的改性作用

固相反应;放电容量;α-PbO纳米粉体的固相合成及其对MnO2电极材料的改性作用     

Ti/α-PbO2/β-PbO2电极电化学降解2-氯酚

采用电化学沉积法在Ti基底上制备了复合电极Ti/α-PbO2/β-PbO2,扫描电镜结果表明电极呈现由β-PbO2小晶体组成的菜花状微观形貌.所制电极在电化学降解环境污染物2-氯酚时表现出较高的电催化效率、较好的电极稳定性和较长的电极寿命.用正交实验优化了电化学降解2-氯酚的实验条件.在最优的实验条件(2-氯酚初始浓度50 mg/L,电解质0.1 mol/L Na2SO4,温度35oC,阳极电流密度20 mA/cm2)下电化学降解180 min后,2-氯酚的去除率达100%.动力学结果表明, Ti/α-PbO2/β-PbO2电极上2-氯酚的电化学氧化符合准一级动力学过程.     

纳米Ag2O2-PbO2化学修饰电极对大肠杆菌细胞膜壁和DNA损伤的研究

制备了一种新型纳米AgO2-PbO2修饰电极,在选定的正电位下,电极表面产生羟基自由基(.OH).通过测定产生的脂质过氧化物和漏出蛋白质的量来研究羟基自由基对大肠杆菌细胞膜壁损伤的情况,并运用电泳和DNA测序的方法对大肠杆菌质粒DNA的损伤及其对序列变化进行了研究.     

The study on microstructure and electrochemical properties of Al�CMg�CSn�CGa�CPb alloy anode material for Al/AgO battery

The microstructure of Al?CMg?CSn?CGa?CPb quinary aluminum alloy anode material and the influences of its electrochemical properties and self-corrosion rate in 4?mol/l NaOH +10?g/l Na₂SnO₃ medium were studied. The microstructure and morphology were characterized by metallographic microscope, transmission electron microscope, and scanning electron microscopy. The electrochemical properties were tested by electrochemical workstation, and the self-corrosion rate of Al alloy anode was studied by methods of recovery H₂ gas by discharge water. The results show that homogenization has not much impact on the electrochemical properties and the corrosion rate of the cast aluminum alloy anode material; besides, return annealing treatment of the cold-rolled Al?CMg?CSn?CGa?CPb quinary aluminum alloy anode material can reduce the rate of self-corrosion and make Al anodic potential shift negative steadily and improve the properties of the material.     

The study on microstructure and electrochemical properties of Al–Mg–Sn–Ga–Pb alloy anode material for Al/AgO battery

The microstructure of Al–Mg–Sn–Ga–Pb quinary aluminum alloy anode material and the influences of its electrochemical properties and self-corrosion rate in 4 mol/l NaOH +10 g/l Na₂SnO₃ medium were studied. The microstructure and morphology were characterized by metallographic microscope, transmission electron microscope, and scanning electron microscopy. The electrochemical properties were tested by electrochemical workstation, and the self-corrosion rate of Al alloy anode was studied by methods of recovery H₂ gas by discharge water. The results show that homogenization has not much impact on the electrochemical properties and the corrosion rate of the cast aluminum alloy anode material; besides, return annealing treatment of the cold-rolled Al–Mg–Sn–Ga–Pb quinary aluminum alloy anode material can reduce the rate of self-corrosion and make Al anodic potential shift negative steadily and improve the properties of the material.

     

Preparation of the Ag2O2-PbO2 Modified Electrode and Its Application towards Escherichia coli Fast Counting in Water

A novel nano crystalline Ag2O2-PbO2 film chemically modified electrode (CME) was prepared and the CME was characterized by X-ray diffractometer (XRD) and atomic focrce microscope (AFM). By chronoamperometry, the nano Ag2O2-PbO2 CME was used as bioelectrochemical sensor to determine the population of Escherichia coli (E.coli) in water. Compared with conventional methods, it is found that the technique we used is fast and convenient in counting E.coil