Surface treatment of CFRP composites using femtosecond laser radiation

In the present work, we investigate the surface treatment of carbon fiber-reinforced polymer (CFRP) composites by laser ablation with femtosecond laser radiation. For this purpose, unidirectional carbon fiber-reinforced epoxy matrix composites were treated with femtosecond laser pulses of 1024 nm wavelength and 550 fs duration. Laser tracks were inscribed on the material surface using pulse energies and scanning speeds in the range 0.1–0.5 mJ and 0.1–5 mm/s, respectively. The morphology of the laser treated surfaces was investigated by field emission scanning electron microscopy. We show that, by using the appropriate processing parameters, a selective removal of the epoxy resin can be achieved, leaving the carbon fibers exposed. In addition, sub-micron laser induced periodic surface structures (LIPSS) are created on the carbon fibers surface, which may be potentially beneficial for the improvement of the fiber to matrix adhesion in adhesive bonds between CFRP parts.     

An anti-reflective 1D rectangle grating on GaAs solar cell using one-step femtosecond laser fabrication

We report the fabrication of the anti-reflective micro/nano-structure on absorbing layer of GaAs solar cell surface using an efficient approach based on one-step femtosecond laser irradiation. Morphology of the microstructures and reflectance of the cell irradiated are characterized with SEM and spectrometer to analyze the influence of laser processing parameters on the change of microstructures induced and the reflectance. It has been found that the rectangle grating micro/nano-structure with a period of 700 nm and width of 600 nm is obtained neatly with laser pulse energy of 30.5 μJ(pulse duration is 130 fs, center wavelength is 800 nm, scanning speed is 2.2 mm/s and spot diameter is 22 µm). Reflectance has been suppressed to 23.6% with rectangle structure from 33% of planar cell. In addition, simulation using a finite-difference-time domain(FDTD) method results show that the rectangle grating micro/nano-structure can effectively suppress the reflection within large wavelength ranges.     

Femtosecond laser processing of indium-tin-oxide thin films

Micro- and nano-scale crystalline indium-tin-oxide (c-ITO) patterns fabricated from amorphous ITO (a-ITO) thin films on a glass substrate using a (low NA 0.26) femtosecond laser pulse that is not tightly focused are demonstrated. Different types of c-ITO patterns are obtained by controlling the laser pulse energies and pulse repetition rate of a femtosecond laser beam at a wavelength of 1064 nm: periodic micro c-ITO dots with diameters of ~1.4 μm, two parallel c-ITO patterns with/without periodic-like glass nanostructures at a laser scanning path and nano-scale c-ITO line patterns with a line width ~900 nm, i.e. ~1/8 of the focused beam׳s diameter (7 μm at 1/e²).     

Realization of periodic transmission filter based on a pair of cascaded long-period fibre gratings of different strength/wavelength position

Using high-intensity (560–650 GW/cm²) 264 nm 220 femtosecond laser pulses, we inscribed a periodic (comb) transmission filter in a photosensitive Ge/B-codoped fibre, based on a pair of long-period gratings of different strength/wavelength position. The irradiation conditions and grating parameters for the successful realization of the 24–28-nm-wide transmission filter in the region 1480–1580 nm with the fringe period of 1.7–3.1 nm and the fringe bandwidth of 0.8–1.3 nm were established.     

A simple method for well-defined and clean all-SiC nano-ripples in ambient air

Well-defined and clean all-SiC nano-ripples with a period of about 150 nm are produced via the combination of 800-nm femtosecond laser irradiation and chemical selective etching with mixture solution of 65 wt% HNO₃ acid (20 mL) and 40 wt% HF acid (20 mL). The incorporation mechanism of oxygen (O) species into the laser induced obscured nano-ripples is attributed to femtosecond laser induced trapping effect of dangling bonds, while that of chemical etching induced well-defined and clean nano-ripples is assigned to chemical reactions between mixture acid solution and amorphous silicon carbide (SiC) or silicon oxide (SiO₂). Results from EDX analysis show that the incorporated foreign O species (atomic percentages of 9.39%) was eliminated effectively via chemical etching, while the atomic percentages of silicon (Si) and carbon (C) were about 47.82% and 52.18% respectively, which were similar to those of original SiC material. And the influences of laser irradiation parameters on the nano-ripples are also discussed.     

Influence of the ZnO nanoparticle sizes and morphology on the photoinduced light reflectivity

We have established a principal possibility of changes of the light reflectivity at the wavelength of 633 nm (He–Ne laser) under influence of the external laser light. The changes are very sensitive to the wavelength of the photoinduced laser. We have chosen two types of the photoinduced lasers: UV nitrogen 7 ns laser at wavelength 371 nm heating near the absorption edge and the 10 ns 1064 nm Nd:YAG laser with wavelength 1064 nm. The power dependences of the reflectivity were studied. Possible explanation of the observed effects is presented following the conception of the nano-trapping levels. These results have been obtained from two ZnO thin films prepared from principally different deposition parameters leading to different particle features and morphologies.     

Part 2: Ultra-short pulse laser patterning of very thin indium tin oxide on glass substrates

We investigate selective patterning of ultra-thin 20 nm Indium Tin Oxide (ITO) thin films on glass substrates, using 343, 515, and 1030 nm femtosecond (fs), and 1030 nm picoseconds (ps) laser pulses. An ablative removal mechanism is observed for all wavelengths at both femtosecond and picoseconds time-scales. The absorbed threshold fluence values were determined to be 12.5 mJ cm⁻² at 343 nm, 9.68 mJ cm⁻² at 515 nm, and 7.50 mJ cm⁻² at 1030 nm for femtosecond and 9.14 mJ cm⁻² at 1030 nm for picosecond laser exposure. Surface analysis of ablated craters using atomic force microscopy confirms that the selective removal of the film from the glass substrate is dependent on the applied fluence. Film removal is shown to be primarily through ultrafast lattice deformation generated by an electron blast force. The laser absorption and heating process was simulated using a two temperature model (TTM). The predicted surface temperatures confirm that film removal below 1 J cm⁻² to be predominately by a non-thermal mechanism.     

High resolution scanning microanalysis on material surfaces using UV femtosecond laser induced breakdown spectroscopy

Femtosecond lasers together with high resolution optics have given us the ability to achieve submicron ablation spots which can play an important role in specific micromachining applications. Light emitted from the plasma at the sample surface created by a focused femtosecond laser pulse can also be used in laser induced breakdown spectroscopy (LIBS) and allows us to characterize the chemical composition of the target surface with micron-level lateral resolution. The spatial resolution using LIBS has often been defined by measuring the FWHM of the crater size. In this report, we study the application of femtosecond 266 nm laser pulses with very low energies of 10׳s of nanojoules. We have investigated spatial resolution using the detection of thin strips of chromium on silicon substrates and compared the actual width of the chromium versus the experimentally obtained width using LIBS detection. The variation of signal levels for low pulse energies is investigated on chromium surfaces. A spatial resolution of ~1 μm was obtained for detection of chromium from the emission.     

Compact resonantly intra-cavity pumped tunable Ho:Sc2SiO5 laser

A compact intra-cavity pumped low threshold continuous-wave Ho:Sc₂SiO₅ laser is reported. The characteristics of output wavelength tuning are investigated by use a intra-cavity briefringent (BF) filter. A wavelength tunable range of 140 nm from 2020 to 2160 nm is achieved. For the free-running mode, the laser slope efficiency is 24.8%, when the output central wavelength is 2110 nm. The laser threshold is about 820 mW of incident pump power. With the BF filter, a maximum output power of 870 mW is obtained at the incident pump power of 5 W, corresponding to a slope efficiency of 20.3%. The characteristics of output wavelength verse the crystal temperature are also investigated.     

Flat and compact switchable dual wavelength output at 1060 nm from ytterbium doped fiber laser with an AWG as a wavelength selector

A dual-wavelength ytterbium doped fiber laser with a narrowest spacing of 0.53 nm and widest spacing of 12.2 nm at 1064 nm is presented in this paper. An arrayed waveguide grating (AWG) together with an optical channel selector (OCS) have also been incorporated in the proposed setup that works as a switchable mechanism giving 23 different wavelength tunings. Producing an average output power of ?8 dB m and side mode suppression ratio (SMSR) of 59.65 dB, this dual-wavelength fiber laser is quite stable with an output power variance as low as 0.47 dB giving it an advantage due to its switching ability and stable dual-wavelength output powers.     

Tunable dual-wavelength fiber laser based on an opto-VLSI processor and four-wave mixing in a photonic crystal fiber

A stable wavelength and wavelength spacing tunable dual-wavelength fiber laser based on an Opto-very-large-scale-integration (Opto-VLSI) processor and four-wave mixing (FWM) in a high-nonlinear photonic crystal fiber is experimentally demonstrated. The results show that the line width of the tunable dual-wavelength fiber laser is 0.02 nm, and the wavelength spacing can be tuned from 0.8 nm to 4 nm with a 0.15 nm step. Under the influence of the FWM, the uniformity is below 0.6 dB and the measured side mode suppression ratio (SMSR) is above 45 dB.     

Experimental femtosecond laser photodisruption of rabbit sclera for minimally invasive laser sclerostomy: An in vitro study

Femtosecond laser technology, used as a minimally invasive tool in intrastromal refractive surgery, may also have potential as a useful instrument for glaucoma filtration surgery. The purpose of the present study was to evaluate the feasibility of minimally invasive laser sclerostomy by femtosecond laser photodisruption and seek the appropriate patterns of laser ablation and relevant laser parameters. A femtosecond laser (800 nm/50 fs/1 kHz), focused by a 0.1 numerical aperture (NA) objective lens, with different pulse energies and exposure times was applied to ablate hydrated rabbit sclera in vitro. The irradiated samples were examined by scanning electron microscopy (SEM). By moving a three-dimensional, computer-controlled translation stage to which the sample was attached, the femtosecond laser could produce three types of ablation patterns, including linear ablation, cylindrical aperture and rectangular cavity. With pulse energies ranging from 37.5 to 150 μJ, the linear lesions were consistently observed at the inner surface of sclera, whereas it failed to make any photodisruption if pulse energy was below the threshold value of 31.25 μJ, with the corresponding threshold intensity of 4.06×10¹⁴ W/cm². The depths of the linear lesions increased linearly with both pulse energy (37.5–150 μJ) and exposure time (0.1–0.4 s). Histological examination showed the incisions produced by femtosecond laser photodisruption had precise geometry and the edges were sharp and smooth, with no evidence of collateral damage to the surrounding tissue. Our results predict the potential application of femtosecond laser pulses in minimally invasive laser sclerostomy for glaucoma treatment.     

Ablation depth control with 40 nm resolution on ITO thin films using a square,flat top beam shaped femtosecond NIR laser

We reported on the ablation depth control with a resolution of 40 nm on indium tin oxide (ITO) thin film using a square beam shaped femtosecond (190 fs) laser (λ_p=1030 nm). A slit is used to make the square, flat top beam shaped from the Gaussian spatial profile of the femtosecond laser. An ablation depth of 40 nm was obtained using the single pulse irradiation at a peak intensity of 2.8 TW/cm². The morphologies of the ablated area were characterized using an optical microscope, atomic force microscope (AFM), and energy dispersive X-ray spectroscopy (EDS). Ablations with square and rectangular types with various sizes were demonstrated on ITO thin film using slits with varying x–y axes. The stereo structure of the ablation with the depth resolution of approximately 40 nm was also fabricated successfully using the irradiation of single pulses with different shaped sizes of femtosecond laser.     

Picosecond laser cutting and drilling of thin flex glass

We investigate the feasibility of cutting and drilling thin flex glass (TFG) substrates using a picosecond laser operating at wavelengths of 1030 nm, 515 nm and 343 nm. 50 μm and 100 μm thick AF32^®Eco Thin Glass (Schott AG) sheets are used. The laser processing parameters such as the wavelength, pulse energy, pulse repetition frequency, scan speed and the number of laser passes which are necessary to perform through a cut or to drill a borehole in the TFG substrate are studied in detail. Our results show that the highest effective cutting speeds (220 mm/s for a 50 μm thick TFG substrate and 74 mm/s for a 100 μm thick TFG substrate) are obtained with the 1030 nm wavelength, whereas the 343 nm wavelength provides the best quality cuts. The 515 nm wavelength, meanwhile, can be used to provide relatively good laser cut quality with heat affected zones (HAZ) of <25 μm for 50 μm TFG and <40 μm for 100 μm TFG with cutting speeds of 100 mm/s and 28.5 mm/s, respectively. The 343 nm and 515 nm wavelengths can also be used for drilling micro-holes (with inlet diameters of ⩽75 µm) in the 100 μm TFG substrate with speeds of up to 2 holes per second (using 343 nm) and 8 holes per second (using 515 nm). Optical microscope and SEM images of the cuts and micro-holes are presented.     

Femtosecond laser ablation of cadmium tungstate for scintillator arrays

Ultrafast pulsed laser ablation has been investigated as a technique to machine CdWO₄ single crystal scintillator and segment it into small blocks with the aim of fabricating a 2D high energy X-ray imaging array. Cadmium tungstate (CdWO₄) is a brittle transparent scintillator used for the detection of high energy X-rays and γ-rays. A 6 W Yb:KGW Pharos-SP pulsed laser of wavelength 1028 nm was used with a tuneable pulse duration of 10 ps to 190 fs, repetition rate of up to 600 kHz and pulse energies of up to 1 mJ was employed. The effect of varying the pulse duration, pulse energy, pulse overlap and scan pattern on the laser induced damage to the crystals was investigated. A pulse duration of ≥500 fs was found to induce substantial cracking in the material. The laser induced damage was minimised using the following operating parameters: a pulse duration of 190 fs, fluence of 15.3 J cm⁻² and employing a serpentine scan pattern with a normalised pulse overlap of 0.8. The surface of the ablated surfaces was studied using scanning electron microscopy, energy dispersive X-ray spectroscopy, atomic force microscopy and X-ray photoelectron spectroscopy. Ablation products were found to contain cadmium tungstate together with different cadmium and tungsten oxides. These laser ablation products could be removed using an ammonium hydroxide treatment.     

Electroactive copper(II) bimetallic self-assembled multilayers on Si(100)

Silicon (100) surfaces were modified by reacting 4-aminopyridine and Si–Cl bond. These surfaces were further used for tethering copper bimetallic complexes and growing monolayers and multilayers by changing the axial position via Lewis acid–base reactions. In this way, coordination chemistry approach can be used as building blocks for controlling the design of functional surfaces. Furthermore, the outcomes of the several characterization techniques indicate that the complex is spatially oriented suggesting that this simple strategy allows the preparation of three dimensional molecular structures exhibiting spatial order. The structures on surface show interesting electroactive behaviors leading two cathodic signals, that can be related to Cu(II)/Cu(I) and Cu(I)/Cu(0) electro-reduction species (signals at ? 0.15 V and ? 0.50 V) and one peak in the anodic region (? 0.15 V) ascribed to the Cu(0)/Cu(II) electro-oxidation reaction, using an Ag/AgCl saturated electrode and platinum wire as reference and counter electrodes, respectively.     

TL and OSL studies on lithium borate single crystals doped with Cu and Ag

Lithium borate (LBO) single crystals doped with Cu and Ag (0.25 mol% each) (Li₂B₄O₇:Cu,Ag) are grown by the Czochralski method. The thermoluminescence readout on Li₂B₄O₇:Cu,Ag crystals showed three glow peaks at～375, 441 and 516 K for the heating rate of 1  K/s. The thermoluminescence sensitivity of the grown Li₂B₄O₇:Cu,Ag single crystals is found to be 5 times TLD-100 and a linear dose response in the range 1 mGy to 1 kGy. The glow curve deconvolution reveals nearly first order kinetics for all the three peaks with trap depths 0.77, 1.25 and 1.34 eV respectively and corresponding frequency factors 1.6×10⁹, 1.3×10¹³ and 6.8×10¹¹ s^?1. The continuous wave optically stimulated luminescence (CW-OSL) measurements were performed on the LBO:Cu,Ag single crystals using blue light stimulation. The traps responsible for the three thermoluminescence peaks in Li₂B₄O₇:Cu,Ag are found to be OSL sensitive. The qualitative correlation between TL peaks and CW-OSL response is established. The photoluminescence studies show that in case of co-doping of Ag in LBO:Cu the emission at 370 nm in Cu states dominates over the transitions in Ag states implying doping of Ag plays a role as sensitizer when co-doped with Cu and increases overall emission.     

Dynamics of plasma formation and permanent structural transformation in ZBLAN excited by tightly focused femtosecond laser pulses

Time-resolved dynamics of plasma formation and bulk refractive-index modification in fluoride glass (ZBLAN) excited by a tightly focused femtosecond (130 fs) Ti:sapphire laser (λ_p=790 nm) was observed in situ. The femtosecond time-resolved pump–probe measurement with perpendicularly linear polarized beams was used to study the dynamics of both plasma formation and induced permanent structural transformation with refractive-index change. In the refractive-index domain, the lifetime of induced plasma formation is ～35 ps and structural transition time for forming the refractive-index change is ～80 ps. In the optical damage domain, however, the lifetime of induced plasma formation is ～40 ps and structural transition time for forming the optical damage is ～140 ps. We found that the process of refractive-index bulk modification is significantly different from that of optical cracks. From the diffraction efficiency of Kogelnik's coupled mode theory, the maximum value of refractive-index change (Δn) was estimated to be 1.3×10^?2. By the scanning of fluoride glass on the optical X–Y–Z stages, the fabrication of internal grating with refractive-index modification was demonstrated in fluoride glass using tightly focused femtosecond laser.     

The influence of oxygen on the growth of silver on Cu(110)

The influence of the (2 × 1)O reconstruction on the growth of Ag on a Cu(110) surface was studied by scanning tunneling microscopy (STM) and Auger electron spectroscopy (AES). On the bare Cu(110) surface, Stranski–Krastanov growth of silver is observed at sample temperatures between 277 K and 500 K: The formation of a Ag wetting layer is followed by the growth of three-dimensional Ag wires. In contrast, on the oxygen-precovered Cu(110) surface, the growth of silver depends heavily on the substrate temperature. Upon Ag deposition at room temperature, a homogeneous, polycrystalline Ag layer is observed, whereas at 500 K, three-dimensional wires separated by (2 × 1)O reconstructed areas are formed. The behavior of a deposited Ag layer upon annealing is also influenced greatly by the presence of oxygen. On the bare surface, annealing does not change the Ag wetting layer and gives rise to Ostwald ripening of the Ag wires. On the oxygen-precovered surface, however, the initial polycrystalline Aglayer first transforms into Ag wires at around 500 K. Above this temperature, the depletion of the (2 × 1)O reconstructed areas due to Ag-induced O desorption is balanced by the formation of a Ag wetting layer. On both, the bare and the oxygen-precovered Cu(110) surface, the deposited silver diffuses into the Cu bulk at temperatures above 700 K.