Side-pumped continuous-wave Cr:Nd:YAG ceramic solar laser

To clarify the advantages of Cr:Nd:YAG ceramics rods in solar-pumped lasers, a fused silica light guide with rectangular cross-section is coupled to a compound V-shaped cavity within which a 7 mm diameter 0.1 at.% Cr:1.0 at.% Nd:YAG ceramic rod is uniformly pumped. The highly concentrated solar radiation at the focal spot of a 2 m diameter stationary parabolic mirror is transformed into a uniform pump radiation by the light guide. Efficient pump light absorption is achieved by pumping uniformly the ceramic rod within the V-shaped cavity. Optimum pumping parameters and solar laser output powers are found through ZEMAX^© non-sequential ray-tracing and LASCAD^© laser cavity analysis codes. 33.6 W continuous-wave laser power is measured, corresponding to 1.32 times enhancement over our previous results with a 4 mm diameter Nd:YAG single-crystal rod. High slope efficiency of 2.6 % is also registered. The solar laser output performances of both the ceramic and the single-crystal rods are finally compared, revealing the relative advantage of the Cr:Nd:YAG rod in conversion efficiency. Low scattering coefficient of 0.0018 cm^?1 is deduced for the ceramic rod. Heat load is considered as a key factor affecting the ceramic laser output performance.     

Optimal ablation of fluorine-doped tin oxide (FTO) thin film layers adopting a simple pulsed Nd:YAG laser with TEM00 mode

In material processing, a laser system with optimal laser parameters has been considered to be significant. Especially, the laser ablation technology is thought to be very important for fabricating a dye-sensitized solar cell (DSSC) module with good quality. Moreover, the TEM₀₀ mode laser beam is the most dominant factor to decide the incident photon to current conversion efficiency (IPCE) characteristics. In order to get the TEM₀₀ mode, a pin-hole is inserted within a simple pulsed Nd:YAG laser resonator. And the spatial field distribution is measured by using three pin-hole diameters of 1.6, 2.0 and 4.0 mm, respectively. At that moment, each case has the same laser beam energy by adjusting the discharge voltage and pulse per second (pps). From those results, it is known that the pin-hole size of 1.6 mm has the perfect TEM₀₀ mode. In addition, at the charging voltage of 1000 V, 10 pps, the feeding speed of 6.08 mm/s and the overlapping rate (OL) of 62%, the scanning electron microscope (SEM) photograph of fluorine-doped tin oxide (FTO) thin film layers shows the best ablation trace.     

Passively Q-switched,high peak power Nd:YAG laser pumped by QCW diode laser

A Nd:YAG laser passively Q-switched by a Cr:YAG showed a high single pulse energy of 53.0 mJ and 5.1 MW peak power. The laser was pumped by quasi-continuous-wave diode bars from single side. The Q-switched pulse had optical-to-optical efficiency of 12% and average temporal duration of 10.4 ns when Cr:YAG with initial transmission of 9.0% was used. Intense pumping as well as very low initial transmission of the saturable absorber gave very high peak power.     

High efficiency diode-pumped slab oscillator and amplifier for space-based application

The design and performance of conduction-cooled, laser diode-pumped oscillator and amplifier slab laser featuring high efficiency, high pulse energy and high beam quality for space-based application are reported. The oscillator was a diode-pumped Q-Switched Nd:YAG slab laser using unstable resonator, and the amplifiers were two zig-zag Nd:YAG slabs based on a side-pumped slab geometry. A near diffraction-limited output of 450 mJ in a 10 ns pulse at a repetition rate of 20 Hz was obtained, corresponding to an optical-to-optical conversion efficiency of over 20%.     

Pulsed Nd:YAG passive Q-switched laser using Cr4+:YAG crystal

In this paper, we report the experimental results of a pulsed flash lamp Nd:YAG laser at wavelength of 1064 nm and Q-switched by Cr⁴⁺:YAG solid state saturable absorber. We have obtained the output energy (E) and pulse- width (τ_p) of this laser for various initial transmissions of this saturable absorber. Furthermore, the effect of reflectivity of the output coupler (R), diameter of the rod (d), and optical length of the cavity (l) on this laser output data have been investigated. We have used the corner cube as a back mirror, which shows high laser stability and better brightness. We have obtained pulse-width 15 ns with 31 mJ output energy. We have also analyzed this laser theoretically and analytically, which agrees well with our corresponding experimental results.     

Pump tuned wide tunable noncritically phase-matched ZnGeP2 narrow line width optical parametric oscillator

A line tunable singly resonant noncritically phase matched narrow band width ZnGeP₂ (ZGP) optical parametric oscillator pumped by the output idler radiation from a KTA OPO based on a 20 mm long KTA crystal pumped from a Q-switched Gaussian shaped Nd:YAG laser beam with a grating having grooves density 85 lines/mm has been demonstrated in the spectral ranges of 3–7 μm. The measured threshold of oscillation energy was 10 μJ. The conversion efficiency was 20.5% and slope efficiency of the ZGP OPO was 20% using a 23 mm long ZGP crystal at 26 mm cavity length. Line width of the generated infrared radiation from ZGP OPO was 37–60 nm.     

Multi-pass traveling-wave amplifier based on an end-pumping Nd:glass slice

This paper describes a multi-pass traveling-wave amplification structure used to amplify 8×8 mm signal lasers with a 5-mm thick Nd:glass slice. The pumping source is a laser diode stack containing eight laser diode arrays. These arrays are carefully placed to maintain high coupling efficiency. Experimental results show that a 300-μJ signal laser can be amplified to 13 mJ with the first 12-pass structure of amplification, and to 246 mJ with its dual-pass feature. The method for solving the thermal problem of this structure is also calculated and analyzed. Results show that the cooling solution of a sapphire slice can effectively reduce the temperature of the pumping side of the Nd:glass slice.     

60 W yellow laser at 561 nm by intracavity frequency doubling of a diode-pumped Q-switched Nd:YAG laser

A high-power yellow laser was achieved by intracavity frequency doubling of a diode-pumped Nd:YAG rod laser. A solid etalon was inserted into the resonator to implement efficient operation of the low-gain single line at 1123 nm transition. By using a LBO crystal inside the cavity as the frequency doubler, the maximum output power of the 561 nm yellow laser was obtained to be as high as 60.3 W with a pulse repetition frequency of 6 kHz, corresponding to an optical-to-optical conversion efficiency of about 6.1%. The output power fluctuation of the yellow laser was measured to be better than 3% in half an hour.     

Experimental research on an arbitrary pulse generation system for imaging VISAR

Imaging VISAR is an important diagnostic tool for a variety of shock-related phenomena in laser-driven experiments. To adapt to various types of shaped driven pulse, the imaging VISAR needs an illuminating light with good shaping capability. Here, a flexible laser probe system was experimentally studied. Being generated from a 1064-nm DFB laser, the continuous wave was modulated by a waveguide amplitude modulator driven by 10 GS/s arbitrary waveform generator. After being amplified by fiber amplifiers and Nd:YAG rod amplifiers, the signal pulse was frequency-converted to 532-nm green light by a thermally controlled LBO crystal with a final output energy larger than 10 mJ. Finally, the green light was coupled into a 1-mm core diameter, multimode fused silica optical fiber and propagated to the imaging VISAR. The probe laser could realize accurate pulse shaping with time resolution below 100 ps. Uniformity in intensity and capability of arbitrary pulse shaping provides great convenience for the analysis of experimental data.     

Influence of the nanoparticle sizes on the photo-induced absorption of La–Ga–S–O–Dy glass nanocomposites

We have established that the illumination by two coherent beams originating from nanosecond Nd:YAG laser at wavelengths 1064 nm and 532 nm in the La–Ga–S–O–Gd:PVA La-Ga-S-O-Dy polymer glass nanocomposites leads to substantial changes in the absorption. The effect is completely reversible and disappears after interruption of the optical treatment. The illumination power density was varied up to 0.6 GW/cm². All the samples show destruction less than 0.2% changes after more than 300,000 laser pulses. The beams were incident with the angles varying between 45° and 50° with respect to the nanocomposite surface. Moreover, the additional analysis of TEM did not demonstrate any additional aggregations. The role of light polarizations, beam stability, and light scattering is discussed.     

Generation of tunable and narrow linewidth continuous-wave yellow laser by sum–frequency mixing of diode-pumped solid-state Nd:YAG ring lasers

We report a tunable, narrow linewidth and high beam quality continuous-wave (CW) yellow laser system at 589 nm. The system is an all solid-state design employing single-pass sum–frequency generation in a KTP crystal by mixing the 1064 nm with 1319 nm lines of two side-pumped Nd:YAG enforcing unidirectional ring lasers. With this method, a CW yellow laser at 589.159 nm with an output power of 0.8 W, a linewidth less than 1.5 GHz and a beam quality M² = 1.29 is obtained. The wavelength of the laser also can be precisely tuned from 589.112 to 589.181 nm in step-length of about 0.22 pm.     

Influence of the ZnO nanoparticle sizes and morphology on the photoinduced light reflectivity

We have established a principal possibility of changes of the light reflectivity at the wavelength of 633 nm (He–Ne laser) under influence of the external laser light. The changes are very sensitive to the wavelength of the photoinduced laser. We have chosen two types of the photoinduced lasers: UV nitrogen 7 ns laser at wavelength 371 nm heating near the absorption edge and the 10 ns 1064 nm Nd:YAG laser with wavelength 1064 nm. The power dependences of the reflectivity were studied. Possible explanation of the observed effects is presented following the conception of the nano-trapping levels. These results have been obtained from two ZnO thin films prepared from principally different deposition parameters leading to different particle features and morphologies.     

A diode end-pumped passively Q-switched Nd:YAG/KTA Raman laser

A diode end-pumped passively Q-switched Nd:YAG/KTA intracavity Raman laser is presented. A KTA crystal with a size of 5 mm × 5 mm × 25 mm is used as the Raman active medium and its 234 cm^?1 Raman mode is employed to finish the conversion from 1064 nm fundamental laser to 1091 nm Raman laser. A 2 mm thick Cr⁴⁺:YAG crystal is used as the saturable absorber. With an LD pump power of 7.5 W, the first-Stokes power of 250 mW is obtained with a pulse repetition frequency of 14.5 kHz. The corresponding diode-to-Stokes conversion efficiency is 3.3% and the pulse energy is 17.2 μJ. Pulse width is measured to be 12.6 ns and peak power is 1.4 kW.     

Efficient femtosecond Yb:YAG laser pumped by a single-mode laser diode

Single-mode diodes enable a particularly simple, compact and effective pumping of solid-state laser devices for many specialized applications. We investigated a single-mode, 300-mW laser diode for pumping at 935 nm a Yb:YAG laser passively mode-locked by a semiconductor saturable absorber. Relatively short pulse generation (156 fs), tunable across 1033–1059 nm has been demonstrated. An optical-to-optical efficiency of about 28% has been obtained with 320 fs long pulses. Therefore, contrarily to what previously believed, compact diode-pumped ultrafast Yb:YAG oscillators can reliably and efficiently deliver pulses in the range of ≈ 100–200 fs with few tens of mW, which are very appealing for bio-diagnostics and amplifier seeding applications.     

Hyperpolarizability and two photon observation of imidazolium picrate

The computational calculation based on the density functional theory at the basis sets level has been employed to compute the first-order hyperpolarizability of the title material. The nonlinear optical properties of imidazolium picrate was assessed by a open aperture z-scan technique in which Nd:YAG laser pulse at 532 nm wavelength was used as excitation source. Laser damage threshold of the crystal was investigated with Nd:YAG assembly for multiple shots and reported. The changes were observed and analyzed on (0 1 1) and (0 0 1) planes.     

Effect of XeCl laser irradiation on the defect structure of Nd:YAG crystals

This paper presents the effect of XeCl laser irradiation on Nd:YAG single crystal samples with various number of pulses at different repetition rates and laser fluences. Effects of the irradiation on the optical and structural properties of the crystal are analyzed by UV–vis-NIR spectroscopy. Annihilation of some point defects of the crystal structure is observed following laser irradiation at a fluence of 100 mJ cm⁻² with 100 and 500 pulses. Increasing the laser fluence and pulse numbers leads to saturation and new defects are found to be formed in the crystal. Additional absorption spectra of the irradiated samples show that oxygen vacancies in the Nd:YAG crystals are removed during the low-dose irradiation. The laser irradiation is compared to the thermal annealing process for Nd:YAG crystal modification. Additional absorption spectrum of an annealed sample reveals that induced negative absorption band at 236 nm is correlated with the annihilation of the oxygen vacancy center. Our results also demonstrate that XeCl laser treatment has several advantages upon annealing at high temperatures in the Nd:YAG crystal quality improvement. Thus, the present work can give a new approach to modify Nd:YAG crystals to be used in a wide variety of solid-state laser engineering.     

Continuous-wave 560 nm light generated by intracavity SrWO4 Raman and KTP sum-frequency mixing

An LD end-pumped Nd:YAG/SrWO₄ continuous-wave 560 nm laser is presented based on intracavity sum-frequency mixing of the fundamental and first-Strokes light. The maximum output power of 330 mW at 559.6 nm was obtained for the diode pump power of 13.7 W and the conversion efficiency was about 2.5%. The intense blue emission was also observed in the SrWO₄ crystal when the Raman laser was operating above threshold. This blue emission is centered at 473 nm, which also happened to YVO₄.     

Doubly Q-switched GdVO4/Nd:GdVO4 laser with AO modulator and Cr4+:YAG saturable absorber under direct 879 nm diode pumping to the emitting level

In this letter, a doubly Q-switched 1.06 μm pulse laser with AO modulator and Cr⁴⁺:YAG saturable absorber by direct pumping grown-together composite GdVO₄/Nd:GdVO₄ crystal is demonstrated for the first time. Compared to purely AO Q-switching, the simultaneous use of AO Q-switch and Cr⁴⁺:YAG saturable absorber can generate shorter pulses and more symmetric temporal profiles. The thermal lens effect of laser crystal was analyzed.     

High power Nd:YAG lasers operating at 1.3 μm wave band

The laser properties of 1.3 μm spectral region in Nd:YAG crystal and their simultaneous dual wavelength threshold condition are investigated. Three types of high power 1.3-μm Nd:YAG quasi continuous wave (QCW) lasers, which operate at 1.319 μm or 1.338 μm single wavelength, 1.319 μm and 1.338 μm simultaneous dual wavelength, are achieved with a maximum average output power of 138 W, 132 W and 120 W, respectively.     

Diode-pumped Nd:YAG ceramic laser at 946 nm passively Q-switched with a Cr4+:YAG saturable absorber

We demonstrate a diode-pumped Nd:YAG ceramic laser with emission at 946 nm that is passively Q-switched by single-crystal Cr⁴⁺:YAG saturable absorber. An average output power of 1.7 W is measured under 18.4 W of incident power using an output mirror with transmission T=4%. The corresponding optical-to-optical efficiency is 9.2%. The laser runs at a pulse repetition rate of 120 kHz and delivers pulses with energy of 14 μJ and duration of 80 ns, which corresponds to a peak power of 175 W.