Effect of carbon black on temperature field and weld profile during laser transmission welding of polymers: A FEM study

The influence of the carbon black on temperature distribution and weld profile, during laser transmission welding of polymers, is investigated in the present research work. A transient numerical model, based on conduction mode heat transfer, is developed to analyze the process. The heat input to the model is considered to be the volumetric Gaussian heat source. The computation of temperature field during welding is carried out for polycarbonates having different proportion of carbon black in polymer matrix. The temperature dependent material properties of polycarbonate are taken into account for modeling. The finite element code ANSYS^® is employed to obtain the numerical results. The numerically computed results of weld pool dimensions are compared with the experimental results. The comparison shows a fair agreement between them, which gives confidence to use the developed model for intended investigation with acceptable accuracy. The results obtained have revealed that the carbon black has considerable influence on the temperature field distribution and the formation of the weld pool geometry.     

Utilization of light scattering in transmission laser welding of medical devices

This paper reports on optimization of material parameters in transmission laser welding of polymers including light absorption, light scattering and the thermal properties of the polymers. A criterion for making an optimized transmission laser weld between a transparent polymer part and an absorbing and scattering polymer part is formulated as a required thickness of the melt-zone in the transparent part with a corresponding minimum-line-energy-for-welding (MLEW). Experimental data of MLEW are presented for a medical device application involving joining polyethylene-octene parts for various concentrations of near-infrared absorber and titanium dioxide light scattering particles. Numerical and analytical models yield good agreement to the experimental data and enable optimization of the transmission laser welding process. By utilization of light scattering, the laser line-energy required for joining two polymer parts can be reduced by a factor up to three, enabling a corresponding reduction of the cycle time in the manufacturing process.     

Analysis of droplet transfer mode and forming process of weld bead in CO2 laser–MAG hybrid welding process

In this paper, CO₂ laser–metal active gas (MAG) hybrid welding technique is used to weld high strength steel and the optimized process parameters are obtained. Using LD Pumped laser with an emission wavelength of 532 nm to overcome the strong interference from the welding arc, a computer-based system is developed to collect and visualize the waveforms of the electrical welding parameters and metal transfer processes in laser–MAG. The welding electric signals of hybrid welding processes are quantitatively described and analyzed using the ANALYSATOR HANNOVER. The effect of distance between laser and arc (D_LA) on weld bead geometry, forming process of weld shape, electric signals, arc characteristic and droplet transfer behavior is investigated. It is found that arc characteristic, droplet transfer mode and final weld bead geometry are strongly affected by the distance between laser and arc. The weld bead geometry is changed from “cocktail cup” to “cone-shaped” with the increasing D_LA. The droplet transfer mode is changed from globular transfer to projected transfer with the increasing D_LA. Projected transfer mode is an advantage for the stability of hybrid welding processes.     

A keyhole volumetric model for weld pool analysis in Nd:YAG pulsed laser welding

This study presents a new model for analyzing the temperature distribution and weld pool shape in Nd:YAG pulsed laser welding. In the proposed approach, a surface flux heat transfer model is applied in the low laser energy intensity region of the weld, while a keyhole heat transfer model based on a volumetric heat source is applied in the high laser energy intensity region of the weld. The correlation between the intensity of the laser input energy and the geometric parameters of the volumetric heat source is derived experimentally. A series of MARC finite element simulations based on the proposed single pulse model are performed to investigate the shape and size of the weld pool given different laser energy intensities. A good agreement is observed between the simulation results and the experimental results obtained under equivalent single pulse welding conditions. Thus, the basic validity of the proposed model is confirmed.     

Modeling and analysis of simultaneous laser transmission welding of polycarbonates using an FEM and RSM combined approach

In this paper, simultaneous laser transmission welding process is systematically investigated via process modeling, using an FEM and RSM combined approach. The objective of the present research is to study the effects of process parameters on the temperature field and weld bead dimensions. The thermal field is simulated by solving a three dimensional transient heat diffusion equation with temperature dependent material properties using the ANSYS^® multi-physics. Response surface methodology is then applied for developing mathematical models based on simulation results. The second order equations developed by RSM can predict the values of the responses with significant accuracy. The effect of parameters and their interactions on the responses are studied using the developed response surface models. The mathematical models are further used in search of the optimal process window for obtaining an acceptable weld. The graphical optimization results into a couple of overlay contours plots, which allow quick visual inspection of the area of feasible response values in the factor space to choose the favorable welding parameter combination.     

电弧特性及其对熔池形貌影响的数值模拟

通过电弧模型与熔池模型耦合数值模拟,研究了氩弧和氦弧特性及其对SUS304不锈钢钨极惰性气体保护（TIG）焊熔池形貌的影响.通过比较氩弧和氦弧的温度轮廓线以及阳极表面电流密度和热流密度分布发现,氦弧的径向距离比氩弧收缩明显,导致更多热量传递给阳极.模拟了氩弧和氦弧下浮力、电磁力、表面张力和气体剪切力分别对熔池形貌的影响.结果表明：不论是在氩弧还是在氦弧下熔池中表面张力是影响熔池形貌的最主要驱动力.在氩弧下,影响熔池形貌的另一个重要的驱动力是气体剪切力,而氦弧下则是电磁力.由于电磁力引起的内对流运动增加了熔深,从而导致相同氧含量时氦弧下的熔深和焊缝深宽比要高于氩弧下的熔深和焊缝深宽比.随着氧含量的增加,氩弧和氦弧下的焊缝深宽比均先增加而后保持不变.焊缝深宽比的模拟结果与实验结果符合较好. 关键词： 氩弧 氦弧 电弧特性 熔池形貌     

Characterization of Kovar-to-Kovar laser welded joints and its mechanical strength

For the packaging of a pump laser in butterfly package, the most crucial assembly step is the fiber-to-laser diode coupling and attachment. The use of laser welding as the joining method offers several advantages if compared with the adhesive joints: strong joining strength, short process time and less contamination. This paper reports on laser welding process characteristics; weld strength and its fracture mode. The penetration depth and melt area of laser spot welds were found to be complicated functions of laser pulse energy, intensity, and beam diameter. Effects of pulse width, input power and size of the focal spot on the rate of energy input to the workpieces and consequently, the weld strength were reported. The weld strength was found to be dependent on the overlapping area between the two joining materials. Surface roughness, R_a, has influence on the fraction of energy absorbed, A, and therefore, affecting the penetration depth. Thermal analysis was carried out on the laser-welded joints and its heat-affected zone (HAZ) induced by various power densities was examined. These data are important in order to optimize and utilize the laser welding process as an effective manufacturing tool for fabrication of reliable pump laser.     

Fibre laser welding for packaging of disposable polymeric microfluidic-biochips

An essential step in the development of microfluidic-biochips is represented by the assembly process. Among the thermal bonding processes used for the assembly of such devices the laser transmission welding of polymers offers several advantages, especially when it comes about local deposition of energy and minimum thermal distortion in the joining components.The research presented in this paper proposes a new approach for the laser transmission welding developed for the packaging of disposable polymeric microfluidic-biochips. The new approach based on the use of a fibre laser and a tailored method for the laser energy deposition was tested on the sealing of polymeric biochips made from plexiglas and polypropylene with a covering foil. This method combines the characteristics of the polymer contour welding and quasi-simultaneous welding and allows the achievement of contamination-free, high quality weld seams as narrow as 100 μm with a high dynamic making it suitable for the high volume production also.     

An investigation on capability of hybrid Nd:YAG laser-TIG welding technology for AA2198 Al-Li alloy

This paper surveys the capability of the hybrid laser-arc welding in comparison with lone laser welding for AA2198 aluminum alloy experimentally. In the present research, a continuous Nd:YAG laser with a maximum power of 2000 W and a 350 A electric arc were used as two combined welding heat sources. In addition to the lone laser welding experiments, two strategies were examined for hybrid welding; the first one was low laser power (100 W) accompanied by high arc energy, and the second one was high laser power (2000 W) with low arc energy. Welding speed and arc current varied in the experiments. The influence of heat input on weld pool geometry was surveyed. The macrosection, microhardness profile and microstructure of the welded joints were studied and compared. The results indicated that in lone laser welding, conduction mode occurred and keyhole was not formed even in low welding speeds and thus the penetration depth was so low. It was also found that the second approach (high laser power accompanied with low arc energy) is superior to the first one (low laser power accompanied with high arc energy) in hybrid laser-arc welding of Al2198, since lower heat input was needed for full penetration weld and as a result a smaller HAZ was created.     

Optimization of hybrid laser – TIG welding of 316LN steel using response surface methodology (RSM)

In the present study, the hybrid laser – TIG welding parameters for welding of 316LN austenitic stainless steel have been investigated by combining a pulsed laser beam with a TIG welding heat source at the weld pool. Laser power, pulse frequency, pulse duration, TIG current were presumed as the welding process parameters whereas weld bead width, weld cross-sectional area and depth of penetration (DOP) were considered as the process responses. Central composite design was used to complete the design matrix and welding experiments were conducted based on the design matrix. Weld bead measurements were then carried out to generate the dataset. Multiple regression models correlating the process parameters with the responses have been developed. The accuracy of the models were found to be good. Then, the desirability approach optimization technique was employed for determining the optimum process parameters to obtain the desired weld bead profile. Validation experiments were then carried out from the determined optimum process parameters. There was good agreement between the predicted and measured values.     

Parameters optimization of laser brazing in crimping butt using Taguchi and BPNN-GA

The laser brazing (LB) is widely used in the automotive industry due to the advantages of high speed, small heat affected zone, high quality of welding seam, and low heat input. Welding parameters play a significant role in determining the bead geometry and hence quality of the weld joint. This paper addresses the optimization of the seam shape in LB process with welding crimping butt of 0.8 mm thickness using back propagation neural network (BPNN) and genetic algorithm (GA). A 3-factor, 5-level welding experiment is conducted by Taguchi L₂₅ orthogonal array through the statistical design method. Then, the input parameters are considered here including welding speed, wire speed rate, and gap with 5 levels. The output results are efficient connection length of left side and right side, top width (WT) and bottom width (WB) of the weld bead. The experiment results are embed into the BPNN network to establish relationship between the input and output variables. The predicted results of the BPNN are fed to GA algorithm that optimizes the process parameters subjected to the objectives. Then, the effects of welding speed (WS), wire feed rate (WF), and gap (GAP) on the sum values of bead geometry is discussed. Eventually, the confirmation experiments are carried out to demonstrate the optimal values were effective and reliable. On the whole, the proposed hybrid method, BPNN-GA, can be used to guide the actual work and improve the efficiency and stability of LB process.     

5083铝合金光纤激光-TIG复合焊接工艺研究

采用IPG YLS-6000光纤激光器和Fronius MagicWave3000job数字化焊机,对4mm厚5083H116铝合金进行了复合焊接试验。研究了电源特性、电流大小和热源间距等工艺参数对光纤激光-钨极惰性气体保护焊(TIG)复合焊接焊缝成形的影响规律,并分析了焊接接头的缺陷、显微硬度及力学性能。结果表明,光纤激光-TIG复合焊接5083铝合金,能够明显改善焊缝成形,提高焊接过程稳定性,特别是与变极性TIG电弧复合效果更为显著;光纤激光与变极性TIG电弧复合焊接,采用激光在前的方式,电弧电流150A,且热源间距不大于4mm,可以得到具有明亮金属光泽和均匀鱼鳞纹的焊缝,焊缝无气孔和裂纹缺陷,其表面有少量的下凹;复合焊接接头抗拉强度为318MPa,达到母材强度的93%,延伸率为7.6%,高于单光纤激光焊接,断口分析为韧性断裂。     

Multi-objective optimization of weld geometry in hybrid fiber laser-arc butt welding using Kriging model and NSGA-II

An integrated multi-objective optimization approach combining Kriging model and non-dominated sorting genetic algorithm-II (NSGA-II) is proposed to predict and optimize weld geometry in hybrid fiber laser-arc welding on 316L stainless steel in this paper. A four-factor, five-level experiment using Taguchi L₂₅ orthogonal array is conducted considering laser power (P), welding current (I), distance between laser and arc (D) and traveling speed (V). Kriging models are adopted to approximate the relationship between process parameters and weld geometry, namely depth of penetration (DP), bead width (BW) and bead reinforcement (BR). NSGA-II is used for multi-objective optimization taking the constructed Kriging models as objective functions and generates a set of optimal solutions with pareto-optimal front for outputs. Meanwhile, the main effects and the first-order interactions between process parameters are analyzed. Microstructure is also discussed. Verification experiments demonstrate that the optimum values obtained by the proposed integrated Kriging model and NSGA-II approach are in good agreement with experimental results.     

Improvement of laser keyhole formation with the assistance of arc plasma in the hybrid welding process of magnesium alloy

In the previous work, low-power laser/arc hybrid welding technique is used to weld magnesium alloy and high-quality weld joints are obtained. In order to make clear the interactions between low-power laser pulse and arc plasma, the effect of arc plasma on laser pulse is studied in this article. The result shows that the penetration of low-power laser welding with the assistance of TIG arc is more than two times deeper than that of laser welding alone and laser welding transforms from thermal-conduction mode to keyhole mode. The plasma behaviors and spectra during the welding process are studied, and the transition mechanism of laser-welding mode is analyzed in detail. It is also found that with the assistance of arc plasma, the threshold value of average power density to form keyhole welding for YAG laser is only 3.3×10⁴ W/cm², and the average peak power density is 2.6×10⁵ W/cm² in the present experiment. Moreover, the distribution of energy density during laser pulse is modulated to improve the formation and stability of laser keyholes.     

Parametric optimisation and microstructural analysis on high power Yb-fibre laser welding of Ti–6Al–4V

In this work thin sheets of Ti–6Al–4V were full penetration welded using a 5 kW fibre laser in order to evaluate the effectiveness of high power fibre laser as a welding processing tool for welding Ti–6Al–4V with the requirements of the aircraft industry and to determine the effect of welding parameters including laser power, welding speed and beam focal position on the weld microstructure, bead profile and weld quality. It involved establishing an understanding of the influence of welding parameters on microstructural change, welding defects, and the characteristics of heat affected zone (HAZ) and weld metal (WM) of fibre laser welded joints. The optimum range of welding parameters which produced welds without cracking and porosity were identified. The influence of the welding parameters on the weld joint heterogeneity was characterised by conducting detailed microstructural analysis.     

Prediction of weld strength and seam width for laser transmission welding of thermoplastic using response surface methodology

In the present work, a study is made to investigate the effects of process parameters, namely, laser power, welding speed, size of the laser beam and clamp pressure, on the lap-shear strength and weld-seam width for laser transmission welding of acrylic (polymethyl methacrylate), using a diode laser system. Response surface methodology (RSM) is employed to develop mathematical relationships between the welding process parameters and the output variables of the weld joint to determine the welding input parameters that lead to the desired weld quality. In addition, using response surface plots, the interaction effects of process parameters on the responses are analyzed and discussed. The statistical software Design-Expert v7 is used to establish the design matrix and to obtain the regression equations. The developed mathematical models are tested by analysis-of-variance (ANOVA) method to check their adequacy. Finally, a comparison is made between measured and calculated results, which are in good agreement. This indicates that the developed models can predict the responses adequately within the limits of welding parameters being used.     

Statistical modeling of laser welding of DP/TRIP steel sheets

In this research work, a statistical analysis of the CO₂ laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets was done using response surface methodology. The analysis considered the effect of laser power (2–2.2 kW), welding speed (40–50 mm/s) and focus position (?1 to 0 mm) on the heat input, the weld bead geometry, uniaxial tensile strength, formability limited dome height and welding operation cost. The experimental design was based on Box–Behnken design using linear and quadratic polynomial equations for predicting the mathematical models. The results indicate that the proposed models predict the responses adequately within the limits of welding parameters being used and the welding speed is the most significant parameter during the welding process.     

3D transient multiphase model for keyhole,vapor plume,and weld pool dynamics in laser welding including the ambient pressure effect

The physical process of deep penetration laser welding involves complex, self-consistent multiphase keyhole, metallic vapor plume, and weld pool dynamics. Currently, efforts are still needed to understand these multiphase dynamics. In this paper, a novel 3D transient multiphase model capable of describing a self-consistent keyhole, metallic vapor plume in the keyhole, and weld pool dynamics in deep penetration fiber laser welding is proposed. Major physical factors of the welding process, such as recoil pressure, surface tension, Marangoni shear stress, Fresnel absorptions mechanisms, heat transfer, and fluid flow in weld pool, keyhole free surface evolutions and solid–liquid–vapor three phase transformations are coupling considered. The effect of ambient pressure in laser welding is rigorously treated using an improved recoil pressure model. The predicated weld bead dimensions, transient keyhole instability, weld pool dynamics, and vapor plume dynamics are compared with experimental and literature results, and good agreements are obtained. The predicted results are investigated by not considering the effects of the ambient pressure. It is found that by not considering the effects of ambient pressure, the average keyhole wall temperature is underestimated about 500 K; besides, the average speed of metallic vapor will be significantly overestimated. The ambient pressure is an essential physical factor for a comprehensive understanding the dynamics of deep penetration laser welding.     

Numerical and experimental investigation of seam welding with a pulsed laser

The present work develops two numerical models to compute thermal phenomena during pulsed laser welding. The first one which is based on finite difference model calculates the welding width and its penetration by utilizing heat transfer equations. Parametric design capabilities of the finite element code ANSYS were also employed for the simulation of the second model. The transient temperature profiles, the fusion dimensions and the heat affected zones (HAZ) have been calculated here. The thermo-physical properties are dependent on temperature and so a nonlinear solution is employed. It is found that the temperature profile and penetration depth are strongly dependent on the pulse parameters of laser beam. Finally, the results of the two models and the experimental outcomes are compared.     

Real time estimation of CO2 laser weld quality for automotive industry

Laser welding is one of the most precise welding processes in joining sheet metals. In laser welding, performing real time evaluation of the welding quality is very important to enhance the efficiency of the welding process. In this study, the plasma and spatter, which are generated during laser welding, are measured using UV and IR photodiodes. The factors that influence weld quality are classified into five categories; optimal heat input, slightly low heat input, low heat input, partial joining due to gap mismatch, and nozzle deviation. The data number deviated from reference signals and their standard deviations were also considered to evaluate the qualities. A system was also formulated to perform real time evaluations of the weld quality using a fuzzy multi-feature pattern recognition with the measured signals.