Refractive index and temperature sensing characteristics of an optical fiber sensor based on a tapered single mode fiber/polarization maintaining fiber

An evanescent field optical fiber sensor based on a short section of polarization maintaining fiber spliced with a tapered single mode fiber is proposed and experimentally investigated. We mainly focus on the refractive index(RI) and temperature sensing characteristics of this compact device. The transmission spectrum of the resonance wavelength,induced by the interference between the excited low order cladding modes and core modes,shows the quadratic function relationships with RI and linear relationships with temperature. Thus,the proposal of this simple-to-fabricate,compact,and low cost sensor shows its possible potential in the sensitive detection field.     

Optimization of a Raman/EDFA hybrid amplifier based on dual-order stimulated Raman scattering using a single-pump

Based on dual-order stimulated Raman scattering (SRS) of a single 1395 nm Raman fiber laser in 75 km single mode fiber and its corresponding dispersion compensation module, a hybrid Raman/Erbium doped fiber amplifier (EDFA) for long wavelength band (L-band) amplification is realized by inserting a segment of EDF within the span. By comparing the performance of gain and noise in four hybrid amplifiers with different span configurations, we find that the distribution of the secondary L-band amplification obtained from the EDF along the link has a great influence on the performance of the hybrid amplifier. Both gain and noise performance of hybrid amplifier can be improved significantly by optimizing the location of the EDF. Moreover, we can extend the flat gain bandwidth from L-band to central wavelength band (C-band) plus L-band by recycling the residual first-order SRS to pump a segment of EDF with proper length.     

光子晶体光纤纤芯整形获得中空模式输出

实验研究了高非线性光子晶体光纤中模式控制的非线性过程,利用激发出高阶模式获得上转换到可见光波段的色散波.通过控制输入飞秒激光的偏振方向,获得了两组相互正交的高阶模式的非线性输出.进一步在光子晶体光纤空气孔包层中注入蜡修整纤芯结构,使得正交模式的有效模折射率差降低,从而形成简并的模式,并通过叠加简并模式获得了中空模场的输出. 关键词： 光子晶体光纤 飞秒激光 频率变换 中空模式     

A high flattening C + L band broadband source based on single pump and the same erbium-doped fiber

In order to realize a high flattening C + L band amplified spontaneous emission (ASE) light output, a broadband source using just one 976 nm laser diode (LD) and two stages erbium-doped fibers (EDF) with the same concentration is proposed theoretically and demonstrated experimentally, and the theoretical analysis and experimental verification are presented in details. Firstly, based on the energy level of Er³⁺, the methods of realizing C + L band ASE output is presented. Then, the system configuration is designed. One 976 nm LD is used for pumping, and the pump light, which is divided into two parts by one coupler, is pumped into two EDFs by wavelength division multiplexer (WDM). A fiber loop mirror (FLM) is used to improve working efficiency. Meanwhile, an optical isolator is used to avoid the effect of reflected wavelength from output facet. Finally, based on the mathematical model of the ASE gain, the length of EDF is discussed as well. In the experiment, by optimizing the length of EDF1 and EDF2, a 0.12 m EDF1 and 16 m EDF2 are adopted. In the end, the flatness of the spectra from 1540 nm to 1610 nm is ±0.91 dB, and the flatness is ±1.65 dB during 1520–1610 nm without any filter. The high flattening C + L band ASE output is achieved by just one 976 nm LD, which can optimize system and reduce the cost as well.     

Design of sidetap fiber Bragg grating filters

A comprehensive theoretical treatment is presented for bound-mode to radiation mode coupling loss (transmission loss) and for bound-mode to bound-mode Bragg reflection (back reflection) in a sidetap fiber phase grating. The spectra of the reflection and transmission loss in a tilt angle range useful for fiber sidetap filter design is presented for the first time. Important dependencies between the designed wavelength of operation and parameters of the fiber grating, which give a clear understanding of the process of the fiber mode to radiation mode coupling and back reflection is also discussed. A practical procedure for the design of sidetap gain flattening filter is also presented.     

Discrimination of strain and temperature based on a polarization-maintaining photonic crystal fiber incorporating an erbium-doped fiber

A simple sensing method for simultaneous measurement of temperature and strain is investigated by using a Sagnac fiber loop mirror composed of a polarization-maintaining photonic crystal fiber (PM-PCF) incorporating an erbium-doped fiber (EDF). Amplified spontaneous emission created by a pumped EDF is transmitted to a Sagnac fiber loop mirror. The interference between two counter-propagating signals in a Sagnac fiber loop mirror generates a periodic transmission spectrum with respect to wavelength. When external temperature is increased, the transmission peak power reduces because the amplified spontaneous emission of the EDF is decreased by the applied temperature change (0.04 dB/°C). The peak wavelength is shifted into the shorter wavelength because of the negative temperature dependence of the birefringence of the PM-PCF (0.3 pm/°C). As the applied strain increases, the peak wavelength of the transmission spectrum of the Sagnac loop mirror incorporating the EDF shifts into a longer wavelength (1.3 pm/με) because the phase change of the proposed sensing probe is directly proportional to the applied strain. The transmission peak power, however, is not changed by the applied strain. Since the source and the sensing probe are integrated, the overall system configuration is significantly simplified without requiring any additional broadband light source. Therefore, it is possible to simultaneously measure temperature and strain by monitoring the variation of transmission peak power and peak wavelength, respectively.     

基于薄芯光纤模态干涉技术的曲率光纤传感器

提出了一种新的基于薄芯光纤模态干涉技术的光纤曲率传感器。在单模光纤的中间部分插入薄芯光纤用于传感光路,没有插入薄芯光纤的单模光纤用于参考光路,以消除环境对曲率测量的影响。由于插入的薄芯光纤和单模光纤纤芯失配,导致包层的高次模被激发,并与纤芯模在单模光纤内形成干涉。当改变薄芯光纤的曲率时,沿纤芯和包层传播的模态和光纤长度会发生改变,使得干涉谷峰发生平移。将传感光纤的两端固定的平移台上,当调节平移台距离时,薄芯光纤的曲率发生改变,导致干涉谷峰向短波方向平移。通过观察谷峰的平移距离可以实现曲率的传感测量。实验表明,该装置具有低损耗、低成本和高灵敏度的特点。     

HEM11模磁绝缘线振荡器的高频分析

作为小型化和紧凑型的高功率微波源,磁绝缘线振荡器(MILO)在过去十几年里得到了广泛的研究和发展.在大多数研究中,最低的对称模一直被当作器件的主模.然而,由于结构的对称性或者电子发射均匀度不理想等原因,很容易激励起非对称模式.计算了MILO同轴结构中同时包含对称模和非对称模的本征方程.在此基础上,通过对结构的优化设计,提出了一种HEM₁₁模工作的MILO,并开展了原理性实验.在二极管的电压为480kV,电流为39kA条件下得到了功率为1.2GW,脉冲宽度为40ns的微波输出,功率转换 关键词： 磁绝缘线振荡器 高频特性 11模')" href="#">HEM₁₁模 开放腔     

高功率光纤中传输光模式与其波长相关性研究

针对高功率光纤激光模式诊断和光谱诊断的需求,研究了光纤中传输模式的波长相关性,数值计算了光纤中各个模式的模场分布随波长的变化曲线及相应的光束质量,采用双傅里叶变换F~2法实际测量了光纤模式成分与波长的关系曲线.结果表明,光纤中各个模式的模场分布随波长变化,波长越长,模场面积越大;模式的光束质量随波长变化不大,但在截止频率附近明显变差;光纤中各个模式的功率占比与波长有关.     

Limitation in the intrinsic method of EDFA gain optimization for 32 × 40 Gbit/s WDM systems

The gain flattening of the erbium doped fiber amplifier (EDFA) is one of the most important aspects in the EDFA which the gain is wavelength dependent. For the first time the limitation of EDFA gain optimizing for a 32-channel wavelength division multiplexing (WDM) systems is investigated and reported in this paper. In a 32-channel WDM system the most favorable flatness gain achieved was 23.16 ± 1.51 dB with an average noise figure of 5.70 dB. This outcome proposes that the method does not achieve a uniform spectral gain in a 32-channel WDM system that incorporates a bandwidth of around 25 nm. Based on the simulation results the intrinsic optimization of EDFA causes the poor SNR and peak signal power with great variation over a transmission distance of 480 km single mode fiber.     

长周期光纤光栅(LPFGs)的谱结构研究

利用相位匹配条件,从理论和实验上研究了均匀LPFGs的谱结构特点.结果表明,导模和不同包层模耦合产生的光谱特性有很大差别.在模序较小时,谱宽较小;模序增加,谱宽也增加;在某一模序附近,谱宽达到最大;以后随模序增加,谱宽迅速减小.给出了LPFGs中透射谱的最大损耗率及3 dB带宽与包层模序、光栅周期、耦合系数和栅长的关系.这些关系对设计满足特定最大损耗率和带宽的带阻滤波器或增益均衡器提供一种理论参考.选用不同的包层模、耦合系数和栅长,可以设计出谱宽很大或很小的LPFGs.     

Wavelength-selection erbium fiber laser with single-mode operation using simple ring design

In this demonstration, we propose and experimentally investigate a wavelength-selection erbium-doped fiber (EDF) laser in single-longitudinal-mode (SLM) by using simple fiber ring scheme design. We use a tunable bandpass filter (TBF) inside the gain cavity to restrict the lasing frequency. The proposed ring cavities can also serve as the mode filters for side mode suppression. Based on the simple ring cavity design, the mode hopping can be avoided to achieve SLM output. The TBF inside the laser scheme also obtains the wavelength tuning in the range of 1520.02 to 1562.02 nm. In addition, the output performance of the proposed fiber laser has also been discussed.     

双同轴电缆差分传输方式对干扰的抑制作用

传输线对信号的无失真传输是超宽带测量系统准确获得待测波形和量值的前提之一。基于带宽、功率容量、损耗、屏蔽性能、尺寸等诸多因素,在超宽带测量系统中经常选用同轴电缆作为传输线。指出采用单根同轴电缆传输信号时会引入干扰,分析了干扰形成的原因,通过数值模拟确认了干扰的存在和危害;提出采用两根共地同轴电缆共同传输信号并进行差分处理,可以有效消除传输线引入的干扰,分析了干扰消除的过程和原理,将原数值模拟模型中的单同轴电缆替换为双同轴电缆进行仿真计算,对比验证了双同轴电缆差分传输方式对干扰的有效抑制作用;对双同轴电缆差分传输结构进行了实验测试,结果表明,单根同轴电缆会引入较大的干扰信号,通过两根同轴电缆的共地连接、差分处理,可以有效消除干扰,达到高保真传输要求。     

Influence of Er-doped superfluorescent fiber source's spectrum-stability on the SNR of fiber optic gyroscopes

The output spectrum-stability of Er-doped superfluorescent fiber source (SFS) was measured by changing the temperature around the excited Er-doped fiber (EDF). With the experiment results, the influences of the SFS's spectrum-stability on the signal-to-noise ratio (SNR) of fiber optic gyroscope (FOG) were simulated. The simulated results demonstrate that the SNR of FOG will change no matter the power, mean wavelength or the spectral bandwidth of the light output from the Er-doped SFS is changing. The results show that the changing of SNR caused by the output power's variation is three orders of magnitude larger than that caused by the variation of mean wavelength or bandwidth. And the main factor influencing the stability of FOG's SNR is the temperature-stability of the output power of Er-doped SFS.     

DESIGN CONSIDERATION OF ERBIUM DOPED FIBER FOR EFFICIENT L-BAND EDFAs

0　Introduction　　Recently,therapidgrowthofInternetanddatacommunicationsserviceshasdriventhedemandforbandwidthinthelong-distancenetworkstodoubleatleasteverytwoyears.Inordertoexploitthelargebandwidthofopticalfiber,technologiessuchaserbium-dopedfiberamplifiers(EDFAs)anddensewavelengthdivisionmultiplexing(DWDM)arewidelyused.Theconventionalwavelengthband(C-band)ofEDFAsextendsfromabout1530to1562nm.Ithasbeenusedforup-to96channelsinDWDMsystem.Itshouldbenotedthatopticalfibernonlineareffectsbe…     

长波段掺铒光纤放大器用掺铒光纤的设计考虑

本文分析了长波段掺铒光纤放大器(EDFA)的增益系数与Er³⁺离子浓度的关系.研制了铝共掺杂的高浓度掺铒光纤,以缩短长波段掺铒光纤的长度.用两级泵浦实现了L-波段EDFA.光纤放大器的掺铒光纤总长18m,在1570nm波长处的小信号增益为42.26dB,输出功率为17.5dBm.我们认为,较低的浓度淬灭效应归因于光纤中较高的A1掺杂浓度.当总的输入信号功率为-3dBm时,在1570至1600nm间的7路WDM信号的增益不平坦度仅为0.68dB..     

Tunable laser generation with erbium-doped microfiber knot resonator

A tunable laser is demonstrated using a microfiber knot resonator structure made by erbiumdoped fiber (EDF). The laser is made of a 2 m long EDF where 30 mm of its end section is tapered to construct a microfiber knot resonator (MKR). The combination of the EDF and MKR generates a stable single wavelength laser at 1555 nm wavelength with a signal to noise ratio (SNR) of 33.7 dB using a 63 mW of 980 nm pump power. The peak wavelength of the laser can be tuned by 340 pm as the MKR diameter reduces from 5.0 to 0.5 mm with an acceptable penalty in output power.     

一种结构新颖的L波段掺铒光纤激光器

提出了一种结构新颖的L波段环形腔掺铒光纤激光器。用掺铒光纤作为增益介,采用980nm激光器作为前向抽运源,利用起偏器和偏振控制器获得L波段激光,利用光环形器将后向的放大自发辐射再引入铒光纤的前端,重复利用。当抽运功率为103mW时得到了阈值功率约为23．87mW,输出功率达6．34mW的激光输出,斜率效率约为8．05％,与没有重复利用后向放大自发辐射谱的掺铒光纤激光器做比较,该结构对L波段掺铒光纤激光器的性能有明显的提升作用。对于长度不合适的铒纤,在没有重复利用后向放大自发辐射谱时没有获得激光输出;而在利用后向放大自发辐射后,在阈值功率约为88mW时得到了激光输出,从而很好地证明了上述结论。     

基于多波长类噪声脉冲的掺铒光纤激光器

报道了一种基于多波长类噪声脉冲的被动锁模掺铒光纤激光器。采用980 nm半导体激光器作为泵浦源，2.5 m长的掺铒光纤作为增益介质。锁模机制为非线性放大环形镜(NALM)。通过自相关迹证明输出脉冲为类噪声脉冲。该类噪声脉冲的光谱3 dB带宽可达17.2 nm，边模抑制比为47.7 dB，重复频率为5.434 MHz，单脉冲能量为7.9 nJ。为了实现平坦的多波长输出，在NALM结构中加入Sagnac环干涉仪，获得了最大波长数为5的平坦多波长类噪声脉冲，平坦度为1.995。     

The influence of the carrier-dependent shifts of the longitudinal modes and the gain profile on the emission characteristics of a pulsed Al x Ga1−x As double heterostructure laser

The wavelength of the longitudinal modes of a stripe geometry DH laser excited by current pulses is shifted according to the variation of the optical power. The magnitude of the spectral shift and the different form of these patterns are due to the mutual influence of individual modes. The time-varying carrier concentration gives rise to a time-dependent (effective) refractive index which alters the resonance condition for the modes. The spectral broadening of the modes, spanning nearly one mode separation, is due to the spectral shift of the modes which in turn depend on the variation of the emitted power. The longitudinal modes are sequentially excited because the gain profile changes its wavelength position with varying carrier concentration.