A double-layered photoanode made of ZnO/TiO<Subscript>2</Subscript> composite nanoflowers and TiO<Subscript>2</Subscript> nanorods for high efficiency dye-sensitized solar cells

We present a simple sol-gel hydrothermal process for the fabrication of a double-layered structure composed of a TiO₂ nanorod overlayer and TiO₂ nanoparticle-embedded ZnO nanoflower (ZNFs@TNPs-TNRs) underlayer. The ZNFs@TNPs-TNRs was used as a photoanode in dye-sensitized solar cells (DSSCs) and their photovoltaic performance was analyzed. The ZNFs@TNPs-TNRs can enhance the adsorption of N719 dyes, charge transport, and light scattering. The cell performances can be maximized by optimizing thickness ratio and total thickness of the double-layered photoanode, and the preliminary results demonstrate that a promising power conversion efficiency (PCE) of 8.01% is determined on the DSSC with ZNFs@TNPs-TNRs anode, yielding a 28.9% enhancement in the PCE in comparison to pristine TiO₂–P25 nanoparticle-based DSSC.     

Multifunctional Ag‐Decorated Porous TiO2 Nanofibers in Dye‐Sensitized Solar Cells: Efficient Light Harvesting,Light Scattering,and Electrolyte Contact

Designing the photoanode structure in dye‐sensitized solar cells (DSSCs) is vital to realizing enhanced power conversion efficiency (PCE). Herein, novel multifunctional silver‐decorated porous titanium dioxide nanofibers (Ag/pTiO₂ NFs) made by simple electrospinning, etching, and chemical reduction processes are introduced. The Ag/pTiO₂ NFs with a high surface area of 163 m² g^?1 provided sufficient dye adsorption for light harvesting. Moreover, the approximately 200 nm diameter and rough surface of the Ag/pTiO₂ NFs offered enough light scattering, and the enlarged interpores among the NFs in the photoanode also permitted electrolyte circulation. Ag nanoparticles (NPs) were well dispersed on the surface of the TiO₂ NFs, which prevented aggregation of the Ag NPs after calcination. Furthermore, a localized surface plasmon resonance effect by the Ag NPs served to increase the light absorption at visible wavelengths. The surface area and amount of Ag NPs was optimized. The PCE of pTiO₂ NF‐based DSSCs was 27 % higher (from 6.2 to 7.9 %) than for pure TiO₂ NFs, whereas the PCE of Ag/pTiO₂ NF‐based DSSCs increased by about 12 % (from 7.9 to 8.8 %). Thus, the PCE of the multifunctional pTiO₂ NFs was improved by 42 %, that is, from 6.2 to 8.8 %.     

Enhanced photovoltaic characterization and charge transport of TIO2 nanoparticles/nanotubes composite photoanode based on indigo carmine dye-sensitized solar cells

Dye-sensitized solar cells (DSSCs) have established themselves as an alternative to conventional solar cells owing to their remarkably high power conversion efficiency, longtime stability and low-cost production. DSSCs composed of a dyed oxide semiconductor photoanode, a redox electrolyte and a counter electrode. In these devices, conversion efficiency is achieved by ultra-fast injection of an electron from a photo excited dye into the conduction band of metal oxide followed by subsequent dye regeneration and holes transportation to the counter electrode. The energy conversion efficiency of DSSC is to be dependent on the morphology and structure of the dye adsorbed metal oxide photoanode. Worldwide considerable efforts of DSSCs have been invested in morphology control of photoanode film, synthesis of stable optical sensitizers and improved ionic conductivity electrolytes. In the present investigation, a new composite nano structured photoanodes were prepared using TiO₂ nano tubes (TNTs) with TiO₂ nano particles (TNPs). TNPs were synthesized by sol–gel method and TNTs were prepared through an alkali hydrothermal transformation. Working photoanodes were prepared using five pastes of TNTs concentrations of 0, 10, 50, 90, and 100 % with TNPs. The DSSCs were fabricated using Indigo carmine dye as photo sensitizer and PMII (1-propyl-3-methylimmidazolium iodide) ionic liquid as electrolyte. The counter electrode was prepared using Copper sulfide. The structure and morphology of TNPs and TNTs were characterized by X-ray diffraction and electron microscopes (TEM and SEM). The photocurrent efficiency is measured using a solar simulator (100 mW/cm²). The prepared composite TNTs/TNPs photoanode could significantly improve the efficiency of dye-sensitized solar cells owing to its synergic effects, i.e. effective dye adsorption mainly originated from TiO₂ nanoparticles and rapid electron transport in one-dimensional TiO₂ nanotubes. The results of the present investigation suggested that the DSSC based on 10 % TNTs/TNPs showed better photovoltaic performance than cell made pure TiO₂ nanoparticles. The highest energy-conversion efficiency of 2.80 % is achieved by composite TNTs (10 %)/TNPs film, which is 68 % higher than that pure TNPs film and far larger than that formed by bare TNTs film (94 %). The charge transport and charge recombination behaviors of DSSCs were investigated by electrochemical impedance spectra and the results showed that composite TNTs/TNPs film-based cell possessed the lowest transfer resistances and the longest electron lifetime. Hence, it could be concluded that the composite TNTs/TNPs photoanodes facilitate the charge transport and enhancing the efficiencies of DSSCs.     

Effect of organic dye on the performance of dye-sensitized solar cell utilizing TiO2 nanostructure films synthesized via CTAB-assisted liquid phase deposition technique

This work is concerned with the growth of TiO₂ nanostructures as photovoltaic materials of dyesensitized solar cell (DSSC) via phase liquid deposition technique treated with CTAB surfactant. This work investigates the influence of organic dyes, N719, N3 and Z907 as photosensitizer on the photovoltaic parameters of TiO₂ nanostructures dye-sensitized solar cells (DSSCs). It also highlights the effect of the concentration of the best dye, N719 on the performance of the cell. The platinum films as counter electrode of the DSSC were prepared by sputtering platinum pellet on ITO substrate. The redox couple of the electrolyte utilized in the DSSC was iodide/triiodide. The cell sensitized with N719 dye demonstrated the best performance compared with the cell sensitized with another two dyes, N3 and Z907. This is due to N719 dye possess the highest optical absorption in visible region. The cell sensitized with 0.8 mM N719 dye performs the highest short-circuit current density, J _sc and power conversion efficiency, η since it posses the highest absorption in visible region. The DSSC utilizing 0.8 mM N719 dye demonstrated the highest J _sc and η of 6.48 mA cm^?2 and 1.69%, respectively.     

二氧化钛纳米晶溶胶内渗透电极对染料敏化太阳能电池的光伏性能的提高

以自制的过氧钛酸(PTA)水溶液为前驱体,用水热法制备了透明锐钛矿相二氧化钛溶胶.无需有机添加剂可得到直径小于7 nm的棒状二氧化钛纳米晶溶胶.通过将溶胶内渗透到染料敏化太阳能电池(DSSCs)的多孔二氧化钛电极后,消除了多孔电极内的大孔并改善了电极内纳米晶之间的连通性.用扫描电子显微镜(SEM)和光学轮廓仪对溶胶内渗透后的光阳极进行了表征.结果表明:小颗粒棒状二氧化钛纳米晶附着在多孔的二氧化钛表面,填充了电极由于烧结产生的大孔,并在多孔的二氧化钛内部形成了有利于电子传输的网络结构.与未经处理的多孔电极相比,改性后的光阳极组装成染料敏化太阳能电池后光电转化效率提高了64%.     

Metal-free indoline dye sensitized solar cells based on nanocrystalline Zn2SnO4

Zn₂SnO₄ nanocrystals were synthesized and first used as the electrode materials for the metal-free indoline dyes sensitized solar cells (DSSCs). The highest efficiency of 3.08% was achieved for a D131 DSSC. This might be attributed to the fact that the D131 dye has a greater positive oxidation potential, which can lead to rapid dye regeneration, avoiding the geminate charge recombination between oxidized dye molecules and injected electrons in the Zn₂SnO₄ film. The efficiency can be improved significantly using a mixture solution of D131 and N719 dyes for which an efficiency of 3.6% was obtained.     

Raman spectroscopic study of dye adsorption on TiO2 electrodes of dye-sensitized solar cells

The state of dye adsorption on TiO₂ electrodes in dye-sensitized solar-cell (DSSC) systems is important for its power-conversion efficiency (PCE). We propose a non-destructive and quantitative method to evaluate the amount of adsorbed dye on TiO₂ electrodes by using micro-Raman spectroscopy. The Raman peak intensity ratio of adsorbed dye to TiO₂, I_d/I_t, is defined as a dye adsorption parameter. Based on a comparison between I_d/I_t and the amount of dye evaluated from UV–vis absorption, the quantitativity and reproducibility of our method are verified.We investigated the change of I_d/I_t spatial distribution of TiO₂ electrodes immersed in a dye solution for different time scales. The statistical analysis of I_d/I_t distribution suggests that dyes adsorbed on TiO₂ electrodes with chemical coordination increase at first, and after their saturation, dye aggregations are formed over the chemisorption layer. We also describe the effect of the I_d/I_t distribution on PCE. From a comparison of PCE and I_d/I_t distribution obtained from various immersion processes, it was considered that the PCE of DSSCs can be optimized by minimizing the I_d/I_t dispersion.     

Dye‐sensitized solar cells based on zinc(II) phthalocyanines bearing 3‐pyridin‐3‐ylpropoxy anchoring groups

In this study, nonperipherally tetra‐substituted ( 2 ), peripherally tetra‐substituted ( 3 ), and peripherally octa‐substituted ( 4 ) zinc(II) phthalocyanines were synthesized as sensitizers for dye‐sensitized solar cells (DSSCs) in which 3‐pyridin‐3‐ylpropoxy substituent acts as anchoring unit to bind TiO₂ surface. The optical results indicated that there is an interaction between the dyes and the TiO₂ surface. The photovoltaic performances of the DSSCs based on these dyes were found to depend on both the position and number of the substituents. Despite the more red‐shifted absorption, the DSSC based on 2 showed the conversion efficiency of 0.68%, which is lower than 1.36% and 0.92% for 3 and 4 , respectively, under one sun (AM 1.5G). The vertical orientation of the dye on TiO₂ surface could be the main reason for the higher photovoltaic performance of complex 3 , which is beneficial for not only injecting the electrons into the conduction band of TiO₂ but also reducing the charge recombination. Overall, these results demonstrate that the peripherally tetra‐substituted 3‐pyridin‐3‐ylpropoxy zinc(II) phthalocyanine complex ( 3 ) as a sensitizer can more efficiently utilize the photons in the red/near‐infrared region with respect to the other complexes studied.     

Hydrothermal Synthesis of a Crystalline Rutile TiO2 Nanorod Based Network for Efficient Dye‐Sensitized Solar Cells

One‐dimensional (1D) TiO₂ nanostructures are desirable as photoanodes in dye‐sensitized solar cells (DSSCs) due to their superior electron‐transport capability. However, making use of the DSSC performance of 1D rutile TiO₂ photoanodes remains challenging, mainly due to the small surface area and consequently low dye loading. Herein, a new type of photoanode with a three‐dimensional (3D) rutile‐nanorod‐based network structure directly grown on fluorine‐doped tin oxide (FTO) substrates was developed by using a facile two‐step hydrothermal process. The resultant photoanode possesses oriented rutile nanorod arrays for fast electron transport as the bottom layer and radially packed rutile head‐caps with an improved large surface area for efficient dye adsorption. The diffuse reflectance spectra showed that with the radially packed top layer, the light‐harvesting efficiency was increased due to an enhanced light‐scattering effect. A combination of electrochemical impedance spectroscopy (EIS), dark current, and open‐circuit voltage decay (OCVD) analyses confirmed that the electron‐recombiantion rate was reduced on formation of the nanorod‐based 3D network for fast electron transport. As a resut, a light‐to‐electricity conversion efficiency of 6.31 % was achieved with this photoanode in DSSCs, which is comparable to the best DSSC efficiencies that have been reported to date for 1D rutile TiO₂.     

Controlling Interfacial Charge Transfer and Fill Factors in CuO‐based Tandem Dye‐Sensitized Solar Cells

We designed and synthesized a series of novel electron‐accepting zinc(II)phthalocyanines (ZnPc) and probed them in p‐type dye sensitized solar cells (p‐DSSCs) by using CuO as photocathodes. By realizing the right balance between interfacial charge separation and charge recombination, optimized fill factors (FFs) of 0.43 were obtained. With a control over fill factors in p‐DSSCs in hand we turned our attemtion to t‐DSSCs, in which we combined for the first time CuO‐based p‐DSSCs with TiO₂‐based n‐DSSCs using ZnPc and N719. In the resulting t‐DSSCs, the V_OC of 0.86 V is the sum of those found in p‐ and n‐DSSCs, while the FF remains around 0.63. It is only the smaller J_scs in t‐DSSCs that limits the efficiency to 0.69 %.     

Dye-sensitized solar cells based on donor-π-acceptor fluorescent dyes with a pyridine ring as an electron-withdrawing-injecting anchoring group

A new‐type of donor–acceptor π‐conjugated (D‐π‐A) fluorescent dyes NI3 – NI8 with a pyridine ring as electron‐withdrawing‐injecting anchoring group have been developed and their photovoltaic performances in dye‐sensitized solar cells (DSSCs) are investigated. The short‐circuit photocurrent densities and solar energy‐to‐electricity conversion yields of DSSCs based on NI3 – NI8 are greater than those for the conventional D‐π‐A dye sensitizers NI1 and NI2 with a carboxyl group as the electron‐withdrawing anchoring group. The IR spectra of NI3 – NI8 adsorbed on TiO₂ indicate the formation of coordinate bonds between the pyridine ring of dyes NI3 – NI8 and the Lewis acid sites (exposed Tiⁿ⁺ cations) of the TiO₂ surface. This work demonstrates that the pyridine rings of D‐π‐A dye sensitizers that form a coordinate bond with the Lewis acid site of a TiO₂ surface are promising candidates as not only electron‐withdrawing anchoring group but also electron‐injecting group, rather than the carboxyl groups of the conventional D‐π‐A dye sensitizers that form an ester linkage with the Brønsted acid sites of the TiO₂ surface.     

SiO2/TiO2 Hollow Nanoparticles Decorated with Ag Nanoparticles: Enhanced Visible Light Absorption and Improved Light Scattering in Dye‐Sensitized Solar Cells

Hollow SiO₂/TiO₂ nanoparticles decorated with Ag nanoparticles (NPs) of controlled size (Ag@HNPs) were fabricated in order to enhance visible‐light absorption and improve light scattering in dye‐sensitized solar cells (DSSCs). They exhibited localized surface plasmon resonance (LSPR) and the LSPR effects were significantly influenced by the size of the Ag NPs. The absorption peak of the LSPR band dramatically increased with increasing Ag NP size. The LSPR of the large Ag NPs mainly increased the light absorption at short wavelengths, whereas the scattering from the SiO₂/TiO₂ HNPs improved the light absorption at long wavelengths. This enabled the working electrode to use the full solar spectrum. Furthermore, the SiO₂ layer thickness was adjusted to maximize the LSPR from the Ag NPs and avoid corrosion of the Ag NPs by the electrolyte. Importantly, the power conversion efficiency (PCE) increased from 7.1 % with purely TiO₂‐based DSSCs to 8.1 % with HNP‐based DSSCs, which is an approximately 12 % enhancement and can be attributed to greater light scattering. Furthermore, the PCEs of Ag@HNP‐based DSSCs were 11 % higher (8.1 vs. 9.0 %) than the bare‐HNP‐based DSSCs, which can be attributed to LSPR. Together, the PCE of Ag@HNP‐based DSSCs improved by a total of 27 %, from 7.1 to 9.0 %, due to these two effects. This comparative research will offer guidance in the design of multifunctional nanomaterials and the optimization of solar‐cell performance.     

Extensive enhancement in power conversion efficiency of dye-sensitized solar cell by using Al-doped TiO<Subscript>2</Subscript> photoanode

In this work, we have prepared Al-doped TiO₂ nanoparticles via a hydrothermal method and used it for making photoanode in dye-sensitized solar cell (DSSC). Material characterizations were done using XRD, AFM, SEM, TEM and EDAX. XPS results reveal that Al is introduced successfully into the structure of TiO₂ creating new impurity energy levels in the forbidden gap. This resulted in tuning of the conduction band of TiO₂ and reduced charge recombination which led to better current conversion efficiency of DSSC. Greater dye loading and enhanced surface area was obtained for Al-doped TiO₂ compared to un-doped TiO₂. I-V analysis, EIS and Bode plots are employed to evaluate photovoltaic performance. The short-circuit current density (J _sc) and efficiency (η) of cell employing Al-doped TiO₂ photoanode were extensively enhanced compared to the cell using un-doped TiO₂. The optical band gap (E _g) for Al-doped and un-doped TiO₂ was obtained as 2.8 and 3.2 eV, respectively. J _sc and η were 13.39 mAcm^?2 and 4.27%, respectively, under illumination of 100 mWcm^?2 light intensity when thin films of 1% Al-doped TiO₂ was employed as photoanode in DSSC using N719 as the sensitizer dye. With the use of un-doped TiO₂ as photoanode under similar conditions, J _sc 5.12 mAcm^?2 and η 1.06% only could be obtained. The maximum IPCE% obtained with Al-doped TiO₂ and un-doped TiO₂ was 67 and 38% respectively at the characteristic wavelength of dye (λ _max = 540 nm). The EIS analyses revealed resistive and capacitive elements that provided an insight into various interfacial processes in terms of the charge transport. It was observed that Al-doping reduced the interfacial resistance leading to better charge transport which has improved both photocurrent density and conversion efficiency. Higher electron mobility and fast diffusion resulting in greater charge collection efficiency was obtained for Al-doped TiO₂ compared to the un-doped TiO₂. Using the Mott–Schottky plot, the donor density was calculated for un-doped and Al-doped TiO₂. The work demonstrated that the Al-doped TiO₂ is potential photoanode material for low-cost and high-efficiency DSSC.     

Evaluation of N719 amount in TiO2 films for DSSC by thermogravimetric analysis

The aim of this work is to evaluate the amount of N719 dye in TiO₂ films for DSSCs by thermogravimetric analysis coupled with mass spectrometry (TG-MS) in comparison with the traditional method based on the dye extraction in NaOH solutions. The characterization was carried out on TiO₂ films applied on FTO glasses by automatic screen printing method. For all the samples, TG-MS showed three well defined steps. The first, below 100 °C and coupled to an endothermic signal was due to water release. From 200 to about 300 °C, there was the release of CO₂ coming from decarboxylation reaction of N719. The last exothermic step was due to the combustion of organic residues. As the decarboxylation reaction occurs with release of 4 moles of CO₂ per mole of N719, it was used to determine the dye loading of the samples that resulted in the range 7?15 wt% well agreeing the relevant content of dye obtained by desorption with NaOH.     

Tin chloride perovskite-sensitized core/shell photoanode solar cell with spiro-MeOTAD hole transport material for enhanced solar light harvesting

An attempt has been made to fabricate methyl ammonium tin chloride (CH₃NH₃SnCl₃) perovskite-sensitized TiO₂ nanostructure photoanode solar cell with hole transport material (HTM) spiro-MeOTAD and graphite-coated counter electrode (CE). The TiO₂ nanoparticles (TNPs), TiO₂ nanoleaves (TNLs), and TNLs with MgO core/shell photoanodes were prepared to fabricate perovskite-sensitized solar cells (PSSCs). The prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The photovoltaic characteristics of the PSSCs, photocurrent density (J _sc), open-circuit voltage (V _oc), fill factor (FF), and power conversion efficiency (PCE) were determined under illumination of AM 1.5 G. Electrochemical impedance spectroscopy (EIS) analysis was carried out to study the charge transport and lifetime of charge carriers at the photoanode–sensitizer–electrolyte interface of the PSSCs. The PSSC made with CH₃NH₃SnCl₃ perovskite-sensitized TNL–MgO core/shell photoanode and spiro-MeOTAD HTM shows an impressive photovoltaic performance, with J _sc = 17.24 mA/cm², V _oc = 800 mV, FF = 73 %, and PCE = 9.98 % under 100 mW/cm² light intensity. The advent of such simple solution-processed mesoscopic heterojunction solar cells paves the way to realize low-cost and high-efficiency solar cells. By the aid of electrochemical impedance spectroscopy, it is revealed that the core/shell structure can increase an interfacial resistance of the photoanode–CH₃NH₃SnCl₃ interface and retard an electron recombination process in the photoanode–sensitizer–HTM interface.     

Effect of TiCl4‐based TiO2 compact and blocking layers on efficiency of dye‐sensitized solar cells

The effect of the number and arrangement of TiO₂‐based photoanode layers on the efficiency of dye‐sensitized solar cells (DSSCs) was investigated. Compact, mesoporous, and blocking layers of TiO₂ were prepared to form monolayer, bilayer, and trilayer photoanodes. Compact and blocking TiO₂ layers were prepared using dip‐coating technique, whereas the doctor‐blade method was employed to prepare TiO₂ paste layers using nanoparticles prepared by the sol–gel method. The crystalline structure of photoanodes was characterized by X‐ray diffraction (XRD) measurements and their morphology and thickness were characterized by the scanning electron microscopy (SEM) technique. The photovoltaic performance of constructed DSSC devices was investigated and the optimum arrangement was identified and explained in terms of dye loading enhancement and recombination reduction at the fluorine‐doped tin oxide (FTO)/electrolyte interface.     

CdSe Quantum Dots and N719‐Dye Decorated Hierarchical TiO2 Nanorods for the Construction of Efficient Co‐Sensitized Solar Cells

Three‐dimensional hierarchical TiO₂ nanorods (HTNs) decorated with the N719 dye and 3‐mercaptopropionic or oleic acid capped CdSe quantum dots (QDs) in photoanodes for the construction of TiO₂ nanorod‐based efficient co‐sensitized solar cells are reported. These HTN co‐sensitized solar cells showed a maximum power‐conversion efficiency of 3.93 %, and a higher open‐circuit voltage and fill factor for the photoanode with 3‐mercaptopropionic acid capped CdSe QDs due to the strong electronic interactions between CdSe QDs, N719 dye and HTNs, and the superior light‐harvesting features of the HTNs. An electrochemical impedance analysis indicated that the superior charge‐collection efficiency and electron diffusion length of the CdSe QD‐coated HTNs improved the photovoltaic performance of these HTN co‐sensitized solar cells.     

Novel D-π-A type II organic sensitizers for dye sensitized solar cells

Four organic donor-π-conjugated-acceptor (D-π-A) type II dyes with different thiophene linkers are reported for dye sensitized solar cells (DSSCs). For the first time, a donor (triphenylamine) was introduced in type II sensitizers, and 2-hydroxybenzonitrile as acceptor/anchoring moiety was covalently linked TiO₂ particles. The dye LS203 in this series gives the best solar energy conversion efficiency of 3.4%, with J_sc = 7.4 mA cm⁻², V_oc = 0.67 V, FF = 0.69, the maximum IPCE value reaches 66.9%.     

电泳法制备具有{001}面TiO2纳米片分级球散射层的染敏太阳电池光电极

利用简便的溶剂热法,制得了由锐钛矿相的纳米片组成的、{001}面接近100%暴露的TiO2分级球形结构。利用电泳沉积法,将所得的TiO2分级球形结构作为散射层引入到染料敏化太阳电池(DSSC)中,并很好地保护了这种脆弱的分级结构。由于这种分级球形结构比TiO2纳米颗粒具有更好的染料吸附性能和光散射性能,使用这种TiO2分级球形结构作为散射层的DSSC达到了7.38%的光电转换效率,较之基于TiO2纳米颗粒的DSSC有了26%的提高。     

Rapid Synthesis of Mesoporous TiO2 for the Photoanodes in Dye Sensitized Solar Cells

Mesoporous TiO₂ microspheres with high specific surface areas were synthesized by means of a facile one‐step microwave hydrothermal process without using any template. The mesoporous materials were rapidly achieved using TiCl₄, urea and ammonium sulphate at comparatively low microwave power (400 W) for 8 min irradiation. The morphology and microstructure of the as‐prepared products were characterized by field emission scanning electron microscopy (FESEM), X‐ray diffraction (XRD), transmission electron microscopy (TEM) and Brunauer‐Emmett‐Teller (BET) surface area analysis. Structural characterization indicates that the TiO₂ microspheres display mesoporous structure. The average pore sizes and BET surface areas of the spheres were 5.3 nm and 222 m²g^?1, respectively. The mesoporous nanocrystals synthesized at 160 °C for 8 min were then used to prepare the photoanode for dye sensitized solar cells (DSSCs). A high power conversion efficiency of 5.72% was achieved from the mesoporous TiO₂ based photoanode, representing about 25.7% improvement over the efficiency of P25 photoanode.