Fabrication and electrochemical performance of nickel ferrite nanoparticles as anode material in lithium ion batteries

Nano-sized nickel ferrite (NiFe₂O₄) was prepared by hydrothermal method at low temperature. The crystalline phase, morphology and specific surface area (BET) of the resultant samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and nitrogen physical adsorption, respectively. The particle sizes of the resulting NiFe₂O₄ samples were in the range of 5–15 nm. The electrochemical performance of NiFe₂O₄ nanoparticles as the anodic material in lithium ion batteries was tested. It was found that the first discharge capacity of the anode made from NiFe₂O₄ nanoparticles could reach a very high value of 1314 mAh g⁻¹, while the discharge capacity decreased to 790.8 mAh g⁻¹ and 709.0 mAh g⁻¹ at a current density of 0.2 mA cm⁻² after 2 and 3 cycles, respectively. The BET surface area is up to 111.4 m² g⁻¹. The reaction mechanism between lithium and nickel ferrite was also discussed based on the results of cycle voltammetry (CV) experiments.     

Significant improved electrochemical performance of Li(Ni1/3Co1/3Mn1/3)O2 cathode on volumetric energy density and cycling stability at high rate

Li(Ni_1/3Co_1/3Mn_1/3)O₂ microspheres with a tap density of 2.41 g cm⁻³ have been synthesized for applications in high power and high energy systems, using a simple rheological phase reaction route. Cyclic voltammograms (CV) showed no shift of anodic and cathodic peaks centred at 3.81, 3.69 V for the Ni²⁺/Ni⁴⁺ couple after first cycle. The results of power pulse area specific impedance (ASI) and differential scanning calorimetry (DSC) tests showed lower power impedance and increased thermal stability of the electrode at high rate. These merits mentioned above provided significant improved capacity and rate performance for Li(Ni_1/3Co_1/3Mn_1/3)O₂ microspheres, which 159, 147 mAh g⁻¹ discharge capacity was delivered after 100 cycles between 2.5–4.6 V vs. Li at a different discharge rate of 2.5 C (500 mA g⁻¹), 5 C and a constant 0.5 C charge rate, respectively.     

Mesoporous Fe2O3 nanoparticles as high performance anode materials for lithium-ion batteries

This work introduces an effective, inexpensive, and large-scale production approach to the synthesis of Fe₂O₃ nanoparticles with a favorable configuration that 5 nm iron oxide domains in diameter assembled into a mesoporous network. The phase structure, morphology, and pore nature were characterized systematically. When used as anode materials for lithium-ion batteries, the mesoporous Fe₂O₃ nanoparticles exhibit excellent cycling performance (1009 mA h g^− 1 at 100 mA g^− 1 up to 230 cycles) and rate capability (reversible charging capacity of 420 mA h g^− 1 at 1000 mA g^− 1 during 230 cycles). This research suggests that the mesoporous Fe₂O₃ nanoparticles could be suitable as a high rate performance anode material for lithium-ion batteries.     

Na4Co2.4Mn0.3Ni0.3(PO4)2P2O7: High potential and high capacity electrode material for sodium-ion batteries

Na₄Co_2.4Mn_0.3Ni_0.3(PO₄)₂P₂O₇ has been evaluated as a positive electrode for sodium-ion batteries. The novel material has two redox couples around 4.2 V and 4.6 V and can deliver the high capacity of ca. 103 mAh g^− 1 at the high current density of 850 mA g^− 1 (5 C). X-ray absorption spectroscopy (XAS) results show that the redox reactions of Co, Mn and Ni ions proceed simultaneously in the charge process and it is indicated the novel material provide high mixed potential by the redox reactions of Co, Mn and Ni ions. These findings suggest that the derivatives of Na₄Co₃(PO₄)₂P₂O₇ should be employed as high potential and high capacity electrode materials.     

Sol–gel preparation and electrochemical performances of LiFe1/3Mn1/3Co1/3PO4/C composites with core–shell nanostructure

LiFe_1/3Mn_1/3Co_1/3PO₄/C solid solution was prepared via a poly(ethylene glycol) assisted sol–gel method and exploited as cathode materials for lithium ion batteries. X-ray diffraction patterns indicate that LiFe_1/3Mn_1/3Co_1/3PO₄/C is crystallized in an orthorhombic structure. The scanning electron microscopy and transmission electron microscopy show that the particles are about 200 nm with a uniform carbon coating of about 8 nm in thickness to form a core–shell nanostructure. During charge–discharge cycles, LiFe_1/3Mn_1/3Co_1/3PO₄/C presented three plateaus corresponding to Fe³⁺/Fe²⁺, Mn³⁺/Mn²⁺ and Co³⁺/Co²⁺ redox couples, and a discharge capacity of 150.8 mAh g^?1 in the first cycle, remaining 121.2 mAh g^?1 after 30 cycles. Core–shell structure can optimize the performances of polyoxoanionic materials for lithium ion batteries.     

High capacity and excellent cyclability of vanadium (IV) oxide in lithium battery applications

A VO₂ · 0.43H₂O powder with a flaky particle morphology was synthesized via a hydrothermal reduction method. It was characterized by scanning electron microscopy, electron energy loss spectroscopy, and thermogravimetric analysis. As an electrode material for rechargeable lithium batteries, it was used both as a cathode versus lithium anode and as an anode versus LiCoO₂, LiFePO₄ or LiNi_0.5Mn_1.5O₄ cathode. The VO₂ · 0.43H₂O electrode exhibits an extraordinary superiority with high capacity (160 mAh g^?1), high energy efficiency (95%), excellent cyclability (142.5 mAh g^?1 after 500 cycles) and rate capability (100 mAh g^?1 at 10 C-rate).     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.     

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

The amorphous Mg–Al–Ni composites were prepared by mechanical ball-milling of Mg₁₇Al₁₂ with x wt.% Ni (x = 0, 50, 100, 150, 200). The effects of Ni addition and ball-milling parameters on the electrochemical hydrogen storage properties and microstructures of the prepared composites have been investigated systematically. For the Mg₁₇Al₁₂ ball-milled without Ni powder, its particle size decreases but the crystal structure does not change even the ball-milling time extending to 120 h, and its discharge capacity is less than 15 mAh g^?1. The Ni addition is advantageous for the formation of Mg–Al–Ni amorphous structure and for the improvement of the electrochemical characteristics of the composites. With the Ni content x increasing, the composites exhibit higher degree of amorphorization. Moreover, the discharge capacity of the composite increases from 41.3 mAh g^?1 (x = 50) to 658.2 mAh g^?1 (x = 200) gradually, and the exchange current density I₀ increases from 67.1 mA g^?1 (x = 50) to 263.8 mA g^?1 (x = 200), which is consistent with the variation of high-rate dischargeability (HRD). The ball-milled Mg₁₇Al₁₂ + 200 wt.% Ni composite has the highest cycling discharge capacity in the first 50 cycles.     

Structure and electrochemical hydrogen storage behaviors of alloy Co2B

The alloys Co₂B were prepared by two ways of high temperature solid phase process and arc melting, the structure of the alloys was characterized by XRD and SEM. It showed that it was structure of tetragonal Co₂B.The electrochemical experimental results demonstrated that the Co₂B prepared by two means both showed excellent cycling stability. The initial discharge capacity of Co₂B prepared by the high temperature solid phase process was 480.3 mA h g⁻¹, there was no distinct declination after 70 charge–discharge cycles and the capacity kept about 195 mA h g⁻¹. Co₂B prepared by the high temperature solid phase process showed very good electrochemical reversibility in CV curves. The hydrogen storage mechanism was also discussed, it confirmed that the high initial capacity of Co₂B prepared by the high temperature solid phase process was due to the oxidation of Co and B₂O₃, and it was irreversible.     

Structural and electrochemical properties of a porous nanostructured SnO2 film electrode for lithium-ion batteries

A B₂O₃-doped SnO₂ thin film was prepared by a novel experimental procedure combining the electrodeposition and the hydrothermal treatment, and its structure and electrochemical properties were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) analysis, energy dispersive X-ray (EDX) spectroscopy and galvanostatic charge–discharge tests. It was found that the as-prepared modified SnO₂ film shows a porous network structure with large specific surface area and high crystallinity. The results of electrochemical tests showed that the modified SnO₂ electrode presents the largest reversible capacity of 676 mAh g^?1 at the fourth cycle, close to the theoretical capacity of SnO₂ (790 mAh g^?1); and it still delivers a reversible Li storage capacity of 524 mAh g^?1 after 50 cycles. The reasons that the modified SnO₂ film electrode shows excellent electrochemical properties were also discussed.     

Sulfone-based electrolytes for high-voltage Li-ion batteries

Sulfone-based electrolytes have been investigated as electrolytes for lithium-ion cells using high-voltage positive electrodes, such as LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ spinels, and Li₄Ti₅O₁₂ spinel as negative electrode. In the presence of imide salt (LiTFSI) and ethyl methyl sulfone or tetramethyl sulfone (TMS) electrolytes, the Li₄Ti₅O₁₂/LiMn₂O₄ cell exhibited a specific capacity of 80 mAh g^?1 with an excellent capacity retention after 100 cycles. In a cell with high-voltage LiNi_0.5Mn_1.5O₄ positive electrode and 1 M LiPF₆ in TMS as electrolyte, the capacity reached 110 mAh g^?1 at the C/12 rate. When TMS was blended with ethyl methyl carbonate, the Li₄Ti₅O₁₂/LiNi_0.5Mn_1.5O₄ cell delivered an initial capacity of 80 mAh g^?1 and cycled fairly well for 1000 cycles under 2C rate. The exceptional electrochemical stability of the sulfone electrolytes and their compatibility with the Li₄Ti₅O₁₂ safer and stable anode were the main reason behind the outstanding electrochemical performance observed with high-potential spinel cathode materials. These electrolytes could be promising alternative electrolytes for high-energy density battery applications such as plug-in hybrid and electric vehicles that require a long cycle life.     

The improvement of the Li-ion insertion behaviour of Li1.05Cr0.10Mn1.85O4 in an aqueous medium upon addition of vinylene carbonate

The influence of vinylene carbonate addition to aqueous LiNO₃ solution on the Li-ion insertion performance of a Li_1.05Cr_0.10Mn_1.85O₄ was studied by galvanostatic charging/discharging. Without additive, the coulombic capacity amounted initially to 80 mA h g^?1 and, during 50 galvanostatic charging/discharging cycles, decreased to 44.1% of the initial value. Upon VC addition in an amount of 1 wt.%, the initial discharge capacity of 112 mA h g^?1 was registered which after 100th charging/discharging cycles retained even 82% of the initial value. This is the first report of a successful use of an additive to improve the behaviour of a Li-intercalation material in an aqueous solution.     

Improving the cycleability of Si anodes by covalently grafting with 4-carboxyphenyl groups

In this study, the lithium storage capacity of Si nanoparticles is significantly enhanced by grafting with 4-carboxyphenyl groups via diazonium salts. The modified Si anodes exhibit reversible capacities of 1173 and 527 mA h g^?1 at the 1st and 50th cycle, while those of the bare Si electrodes are only 56 and 62 mA h g^?1, respectively. The improved electrochemical performance is supposed to arise from the formation of a robust and flexible solid electrolyte interface on the surfaces of the modified Si nanoparticles.     

A Li3V2(PO4)3/C thin film with high rate capability as a cathode material for lithium-ion batteries

A monoclinic lithium vanadium phosphate (Li₃V₂(PO₄)₃) and carbon composite thin film (LVP/C) is prepared via electrostatic spray deposition. The film is studied with X-ray diffraction, scanning and transmission electron microscopy and galvanostatic cell cycling. The LVP/C film is composed of carbon-coated Li₃V₂(PO₄)₃ nanoparticles (50 nm) that are well distributed in a carbon matrix. In the voltage range of 3.0–4.3 V, it exhibits a reversible capacity of 118 mA h g^?1 and good capacity retention at the current rate of 1 C, while delivers 80 mA h g^?1 at 24 C. These results suggest a practical strategy to develop new cathode materials for high power lithium-ion batteries.     

Fabrication of porous carbon/Si composite nanofibers as high-capacity battery electrodes

Carbon/Si composite nanofibers with porous structures are prepared by electrospinning and subsequent carbonization processes. It is found that these porous composite nanofibers can be used as anode materials for rechargeable lithium-ion batteries (LIBs) without adding any binding or conducting additive. The resultant anodes exhibit good electrochemical performance; for example, a large discharge capacity of 1100 mAh g^?1 at a high current density of 200 mA g^?1.     

Chrysanthemum-like Co3O4 architectures: Hydrothermal synthesis and lithium storage performances

Three-dimensional chrysanthemum-like Co₃O₄ was prepared via a facile hydrothermal route without any template, and a subsequent calcination process. With a controlled concentration of the homogeneous precipitation agent, urea, a chrysanthemum-like precursor was hydrothermally obtained at 120 °C for 20 h, and the morphology was kept for Co₃O₄ after a subsequent calcination at 300 °C for 2 h. Co₃O₄ chrysanthemum-like architectures are assemblies of nanorods radiating from a common centre, and the nanorods consisted of interconnected nanoparticles with the size of about 30 nm. When tested as an anode material of Li-ion batteries, chrysanthemum-like Co₃O₄ presented a discharge capacity of ∼450 mA h/g after 50 discharge/charge cycles.     

Li2ZnTi3O8 nanorods: A new anode material for lithium-ion battery

Spinel Li₂ZnTi₃O₈ nanorods were first synthesized using titanate nanowires as a precursor. The synthesized nanorods are highly crystalline and used as an anode material in a rechargeable Li-ion battery. A large capacity of 220 mA h g^? 1 was kept after 30 cycles at a current density of 0.1 A g^? 1, which is close to the theoretic capacity. The electrochemical measurements indicate that the anode material made of spinel Li₂ZnTi₃O₈ nanorods displayed a highly reversible capacity and excellent cycling stability.     

Fabrication and electrochemical properties of the Sn–Ni–P alloy rods array electrode for lithium-ion batteries

A new ternary Sn–Ni–P alloy rods array electrode for lithium-ion batteries is synthesized by electrodeposition with a Cu nanorods array structured foil as current collector. The Cu nanorods array foil is fabricated by heat treatment and electrochemical reduction of Cu(OH)₂ nanorods film, which is grown directly on Cu substrate through an oxidation method. The Sn–Ni–P alloy rods array electrode is mainly composed of pure Sn, Ni₃Sn₄ and Ni–P phases. The electrochemical experimental results illustrate that the Sn–Ni–P alloy rods array electrode has high reversible capacity and excellent coulombic efficiency, with an initial discharge capacity and charge capacity of 785.0 mAh g^?1 and 567.8 mAh g^?1, respectively. After the 100th discharge–charge cycling, capacity retention is 94.2% with a value of 534.8 mAh g^?1. The electrode also performs with an excellent rate capacity.     

Lithium insertion chemistry of some iron vanadates

Lithium insertion into various iron vanadates has been investigated. Fe₂V₄O₁₃ and Fe₄(V₂O₇)₃ · 3H₂O have discharge capacities approaching 200 mAh g⁻¹ above 2.0 V vs. Li⁺/Li. Although the potential profiles change significantly between the first and subsequent discharges, capacity retention is unexpectedly good. Other phases, structurally related to FeVO₄, containing copper and/or sodium ions were also studied. One of these, β-Cu₃Fe₄(VO₄)₆, reversibly consumes almost 10 moles of electrons per formula unit (ca. 240 mAh g⁻¹) between 3.6 and 2.0 V vs. Li⁺/Li, in a non-classical insertion process. It is proposed that both copper and vanadium are electrochemically active, whereas iron(III) reacts to form LiFe^IIIO₂. The capacity of the Cu₃Fe₄(VO₄)₆/Li system is nearly independent of cycling rate, stabilizing after a few cycles at 120–140 mAh g⁻¹. Iron vanadates exhibit better capacities than their phosphate analogues, whereas the latter display more constant discharge potentials.     

Li/LiFePO4 batteries with room temperature ionic liquid as electrolyte

Room temperature ionic liquid (RTIL) was prepared on basis of N-methyl-N-butylpiperidinium bis(trifluoromethanesulfonyl)imide (PP₁₄TFSI), which showed a wide electrochemical window (?0.1–5.2 V vs. Li⁺/Li) and is theoretically feasible as an electrolyte for batteries with metallic Li as anodes. The addition of vinylene carbonate (VC) improved the compatibility of PP₁₄TFSI-based electrolyte towards lithium anodes and enhanced the formation of solid electrolyte interphase film to protect lithium anodes from corrosion. Accordingly, Li/LiFePO₄ cells initially delivered a discharge capacity of about 127 mAh g^?1 at a current density of 17 mA g^?1 in the ionic liquid with the addition of VC and showed better cyclability than in the neat ionic liquid. Electrochemical impedance spectroscopy disclosed that the addition of VC enhanced Li-ion diffusion and depressed interfacial resistance significantly.