Li[Ni1/3Mn1/3Co1/3]O2掺杂Mo研究

采用高温固相合成法制备了Li[Ni_(1－x)/3Mn_(1－x)/3Co_(1－x)/3Mo_x]O₂ (x＝0, 0.005, 0.01, 0.02). 对它们进行了XRD, SEM, 循环伏安及充放电容量测试, 结果发现, 掺杂x＝0.01 Mo的样品具有较高的嵌锂容量和良好的循环稳定性, 在20 mA/g放电电流密度和2.3～4.6 V的电压范围内具有211.6 mAh/g的首次放电比容量, 循环50周后放电比容量仍能达到185.9 mAh/g, 容量损失为12.1%.     

AlF3包覆对Li1.2Mn0.534Ni0.133Co0.133O2正极材料电化学性能的影响

通过共沉淀法制备锂离子电池富锂锰基正极材料Li1.2Mn0.534Ni0.133Co0.133O2,并对其进行AlF3包覆。实验结果表明,通过AlF3包覆,材料的电化学性能得到明显提高。在0.2C下,包覆前材料的首次放电比容量为253 mAh.g-1,首次充放电效率仅为88.8%。经过AlF3包覆,材料的首次放电比容量提高到294 mAh.g-1,首次充放电效率高达96.4%。同样,在1.0C下循环50次,未包覆材料的放电比容量由225 mAh.g-1降到185 mAh.g-1,容量保持率仅为82.2%。经过AlF3包覆,材料的放电比容量由230mAh.g-1仅降为222 mAh.g-1,容量保持率高达96.5%。     

Effect of synthesis routes on the electrochemical performance of Li[Ni0.6Co0.2Mn0.2]O2 for lithium ion batteries

The cathode-active materials, layered Li[Ni_0.6Co_0.2Mn_0.2]O₂, were synthesized by two different routes: spray-drying and solid-state methods. The influence of synthesis routes on the crystal structure, morphology, and electrochemical performance of the samples were characterized by X-ray diffraction, scanning electron microscope, and charge/discharge test. As a result, both samples showed a typical hexagonal structure with a single phase. However, the difference in synthesis route resulted in the difference in morphology and electrochemical performance, such as reversible capacity and the rate capability. The initial discharge capacity of sample synthesized by spray-drying method at room temperature and 50 °C were 173.1 and 181.2 mAh g^?1, respectively, which were higher than those of 166.8 and 177.5 mAh g^?1 for sample synthesized by solid-state method. The cycling performance was also evaluated. Sample synthesized by spray-drying method exhibits a higher discharge capacity and better cycling performance than those prepared by solid-state method, even at elevated temperature.     

Polymer template-assisted microemulsion synthesis of large surface area, porous Li2MnO3 and its characterization as a positive electrode material of Li-ion cells

Lithium-rich manganese oxide (Li₂MnO₃) is prepared by reverse microemulsion method employing Pluronic acid (P123) as a soft template and studied as a positive electrode material. The as-prepared sample possesses good crystalline structure with a broadly distributed mesoporosity but low surface area. As expected, cyclic voltammetry and charge–discharge data indicate poor electrochemical activity. However, the sample gains surface area with narrowly distributed mesoporosity and also electrochemical activity after treating in 4 M H₂SO₄. A discharge capacity of about 160 mAh g^?1 is obtained. When the acid-treated sample is heated at 300 °C, the resulting porous sample with a large surface area and dual porosity provides a discharge capacity of 240 mAh g^?1. The rate capability study suggests that the sample provides about 150 mAh g^?1 at a specific discharge current of 1.25 A g^?1. Although the cycling stability is poor, the high rate capability is attributed to porous nature of the material.     

长循环高电压钠离子电池正极材料P2-Na2/3Mn1/3Bi1/3Ni1/3O2的合成及性能

镍基层状氧化物NaNiO₂钠离子电池材料具有高电压和高容量的特性,且制备方法较为简单,但姜-泰勒(Jahn-Teller)效应使其在高倍率循环下容量较低以及在高电压(4.5 V)下无法稳定循环。通过调节溶胶-凝胶工艺的条件,设计、合成了Na_2/3Mn_1/3Bi_1/3Ni_1/3O₂片层状金属氧化物,并将其作为正极活性材料,在空气环境中组装成钠离子电池,进行电化学测试,考察Bi、Mn掺入量对电池电化学影响。研究结果表明:当金属Mn和Bi共掺时,在1.2~4.5 V宽电压范围内,电池在循环50周后容量为90.39 mAh·g^-1。在2.0~4.0 V电压范围内1.0C (115 mA·g^-1)倍率下恒流充放电50周后的容量保持率为96.96%,循环850周后的保持率为80.15%,具有良好的循环稳定性和安全性。     

Synthesis and Electrochemical Performance of Ti 4＋ Doped LiV 3O 8

溶胶凝胶法合成了层状的LiTiyV3-0.8yO8（y=0, 0.04, 0.06, 0.08）正极材料,这些材料因为掺杂Ti量的不同,而具有了不同的形貌特征（形状,粒径,比表面积）以及电化学性质（首次充放电容量, 循环容量等）。XRD,SEM, CV,及充放电测试对该正极材料的结构和电化学性能进行了表征,结果表明当y=0.04时,该正极材料拥有最高的首次放电容量（348.9mAhg-1）和最好的容量循环性能。     

Li3V2(PO4)3的溶胶-凝胶法合成及其性能研究

以LiOH·H₂O、NH₄VO₃、H₃PO₄和柠檬酸等为原料采用溶胶-凝胶法合成了锂离子二次电池正极材料磷酸钒锂(Li₃V₂(PO₄)₃)。考察了煅烧温度和配位剂种类等条件对产物组成及电化学性能的影响。研究了优化条件下制得样品的循环伏安、充放电性能和循环性能。0.1 C条件下,样品首次放电比容量达129.81 mAh·g^-1，经过100次循环后容量几乎没有衰减，仍保持在128 mAh·g^-1。X射线衍射研究表明合成单一Li₃V₂(PO₄)₃晶体所需温度比固相法低；并考察了循环20次后材料充电到各个单相的晶体结构，通过X射线衍射和最小二乘法计算给出了其晶胞参数变化过程，证实了循环嵌Li过程中晶体结构能够得到重现。     

Synthesis of carbon nanofibers@MnO2 3D structures over copper foil as binder free anodes for lithium ion batteries

A 3D structured composite of carbon nanofibers@MnO₂ on copper foil is reported here as a binder free anode of lithium ion batteries, with high capacity, fast charge/discharge rate and good stability. Carbon nanofiber yarns were synthesized directly over copper foil through a floating catalyst method. The growth of carbon nanofiber yarns was significantly enhanced by mechanical polishing of the copper foils, which can be attributed to the increased surface roughness and surface area of the copper foils. MnO₂ was then grown over carbon nanofibers through spontaneous reduction of potassium permanganate by the carbon nanofibers. The obtained composites of carbon nanofibers@MnO₂ over copper foil were tested as an anode in lithium ion batteries and they show superior electrochemical performance. The initial reversible capacity of carbon nanofibers@MnO₂ reaches up to around 998 mAh·g^?1 at a rate of 60 mmA·g^?1 based on the mass of carbon nanofibers and MnO₂. The carbon nanofibers@MnO₂ electrodes could deliver a capacity of 630 mAh·g^?1 at the beginning and maintain a capacity of 440 mmAh·g^?1 after 105 cycles at a rate of 600 mA·g^?1. The high initial capacity can be attributed to the presence of porous carbon nanofiber yarns which have good electrical conductivity and the MnO₂ thin film which makes the entire materials electrochemically active. The high cyclic stability of carbon nanofibers@MnO₂ can be ascribed to the MnO₂ thin film which can accommodate the volume expansion and shrinking during charge and discharge and the good contact of carbon nanofibers with MnO₂ and copper foil.     

Preparation of Li2SnO3 and its application in lithium‐ion batteries

Tin‐based oxide Li₂SnO₃ has been synthesized by a hydrothermal route as negative material for lithium‐ion batteries. The microstructure and electrochemical properties of the as‐synthesized materials were investigated by some characterizations means and electrochemical measurements. The as‐synthesized Li₂SnO₃ is a porous rod, which is composed of many uniform and regular nano‐flakes with a size of 50–60 nm. Li₂SnO₃ also displays an electrochemical performance with high capacity and good cycling stability (510.2 mAh g^?1 after 50 cycles at a current density of 60 mA g^?1 between 0.0 V and 2.0 V verusus Li/Li⁺). Copyright © 2013 John Wiley & Sons, Ltd.     

SnO2 sheet/graphite composite as anode material with improved electrochemical performance for lithium-ion batteries

The SnO₂ sheet/graphite composite was synthesized by a hydrothermal method for high-capacity lithium storage. The microstructures of products were characterized by XRD and FE-SEM. The electrochemical performance of SnO₂ sheet/graphite composite was measured by galvanostatic charge/discharge cycling and EIS. The first discharge and charge capacities are 1,072 and 735 mAh g^?1 with coulombic efficiency of 68.6 %. After 40 cycles, the reversible discharge capacity is still maintained at 477 mAh g^?1. The results show that the SnO₂ sheet/graphite composite displays superior Li-battery performance with large reversible capacity and good cyclic performance.     

Coating of Al2O3 on layered Li(Mn1/3Ni1/3Co1/3)O2 using CO2 as green precipitant and their improved electrochemical performance for lithium ion batteries

Li(Mn_1/3Ni_1/3Co_1/3)O₂ cathode materials were fabricated by a hydroxide precursor method. Al₂O₃ was coated on the surface of the Li(Mn_1/3Ni_1/3Co_1/3)O₂ through a simple and effective one-step electrostatic self-assembly method. In the coating process, a NHCO₃-H₂CO₃ buffer was formed spontaneously when CO₂ was introduced into the NaAlO₂ solution. Compared with bare Li(Mn_1/3M_1/3Co_1/3)O₂, the surface-modified samples exhibited better cycling performance, rate capability and rate capability retention. The Al₂O₃-coated Li(Mn_1/3Ni_1/3Co_1/3)O₂ electrodes delivered a discharge capacity of about 115 mAh·g^?1 at 2 A·g^?1, but only 84 mAh·g^?1 for the bare one. The capacity retention of the Al₂O₃-coated Li(Mn_1/3Ni_1/3Co_1/3)O₂ was 90.7% after 50 cycles, about 30% higher than that of the pristine one.     

The electrochemical properties of Fe- and Ni-cosubstituted Li2MnO3 via combustion method

The Co-free Li_1.20Mn_0.54Ni _x Fe _y O₂ (x/y?=?0.5, 1.0, 2.0) materials were synthesized by combustion method. The effects of the preparation condition on the structure, morphology, and electrochemical performance were investigated by X-ray diffractometry, scanning electron microscopy, charge–discharge tests, and cyclic voltammetry (CV). The results indicate that the structure and electrochemical characteristics are sensitive to the preparation condition when a large amount of Fe is included. A pure layered α-NaFeO₂ structure with R-3m space group and the discharge capacities of over 200 mAh g^?1 were observed in some as-prepared cathode materials. Particularly, the Li_1.2Mn_0.54Ni_0.13Fe_0.13O₂ prepared by mixing an excess amount of lithium and by firing at 600 °C exhibits a second discharge capacity of 264 mAh g^?1 in the voltage range of 1.5–4.8 V under current density of 30 mA g^?1 at 30 °C and discharge capacity of 223 mAh g^?1 at 2.0–4.8 V. Nevertheless, an unpleasant capacity fading was observed and is primarily ascribed to transformation from a rock-layered structure into a spinel one according to CV testing.     

溶胶-喷雾干燥法制备纳米Li3V2(PO4)3/C及其电化学性能

本文以LiOH.H2O、NH4VO3、H3PO4和柠檬酸为原料,采用溶胶-喷雾干燥法制备Li3V2(PO4)3/C正极材料,对比了喷雾前驱体直接煅烧与机械活化后煅烧的样品的结构、形貌及其电化学性能。采用XRD、SEM、BET和振实密度测试等对样品的结构、形貌等进行了表征;采用恒流充放电、CV和EIS等手段考察了材料的电化学性能。结果表明,溶胶-喷雾干燥得到的样品为多孔球壳形,其壳体由厚度为100 nm左右的纳米片组成,经机械活化后煅烧保持保持了其纳米片结构,其结晶度与振实密度改善较明显,电化学性能较优异。0.1C放电比容量为123.6 mAh.g-1,10C和20C高倍率放电比容量还高达107.8和106.0 mAh.g-1。电化学阻抗结果表明,由该方法制备的样品具有较小的电荷转移阻抗。     

溶胶-凝胶法制备Li3V2(PO4)3及其性能研究

0引言具有类NASICON结构的Li3V2(PO4)3是继过渡金属氧化物LMO后的一种新型的锂离子二次电池正极材料。与目前市场上应用最为广泛的正极材料LiCoO2相比,Li3V2(PO4)3具有超常的稳定性,即使在脱出的Li 与过渡金属原子的物质的量之比大于1的时候仍然具有超乎寻常的稳定性,而通常情况下1mol LiCoO2在脱出0.5mol Li 就会变得不稳定。并且Co是一种战略物资,全球储量十分有限;Co也是一种有毒金属,对于环境污染较为严重。LiNiO2因其合成较为困难而使应用受限,尖晶石LiMn2O4虽然属于环境友好型化合物,但其理论比容量仅为148mAh·g-1,且…     

层状Li(Ni1/3Co1/3Mn1/3)O2正极材料的合成与电化学性能研究

采用共沉淀-喷雾造粒法制备前驱体, 于750 ℃在空气中煅烧20 h合成出层状Li(Ni_1/3Co_1/3Mn_1/3)O₂正极材料, 并用XRD, SEM, 粒度分析和电性能测试考察了所得材料结构、形貌及电化学性能. 本层状Li(Ni_1/3Co_1/3Mn_1/3)O₂正极材料具有α-NaFeO₂结构, 六方晶系, R3m空间群, 其晶胞参数为a＝0.2865 nm, c＝1.4238 nm. 当材料分别在2.8～4.2, 2.8～4.5 V间进行充放电时, 其首次放电容量分别为173.5和185.4 mAh•g^－1, 首次充放电效率分别为90%和83.8%, 40次循环后容量保持率分别为96%和84%.     

One-step hydrothermal synthesis of flower-like SnO2/carbon nanotubes composite and its electrochemical properties

In this work, flower-like SnO₂/carbon nanotubes (CNTs) composite was synthesized by one-step hydrothermal method for high-capacity lithium storage. The microstructures of products were characterized by XRD, FESEM and TEM. The electrochemical performance of the flower-like SnO₂/CNTs composite was measured by cyclic voltammetry and galvanostatic charge/discharge cycling. The results show that the flower-like SnO₂/CNTs composite displays superior Li-battery performance with large reversible capacity and high rate capability. The first discharge and charge capacities are 1,230 and 842 mAh g^?1, respectively. After 40 cycles, the reversible discharge capacity is still maintained at 577 mAh g^?1 at the current densities of 50, 100 and 500 mA g^?1, indicating that it’s a promising anode material for high performance lithium-ion batteries.     

用于可充锂电池的高倍率磷酸铁(II)锂正极材料

本文以聚氧化乙烯为碳源,用柠檬酸辅助湿化学法合成了高倍率的碳包覆的LiFePO₄。使用热重、粉末X射线衍射、扫描电子显微镜、透射电子显微镜、循环伏安、电化学阻抗和恒流充放电表征材料的结构和电化学性质。结果表明,该材料组成为5 wt%疏松多孔的碳包覆相纯度很高的小的LiFePO₄颗粒。该材料适用于高倍率充放电,在5 C、10 C和20C的放电倍率下可以分别得到120、90和60 mAh·g^-1的稳定容量。     

Conducting Graphene Decorated Li3V2(PO4)3/C for Lithium‐Ion Battery Cathode with Superior Rate Capability and Cycling Stability

In this study, core‐shell structured Li₃V₂(PO₄)₃/C wrapped in graphene nanosheets has been successfully prepared. The reduction of graphene oxide and the synthesis of Li₃V₂(PO₄)₃/C are carried out simultaneously using a chemical route followed by a solid‐state reaction. The effects of conducting graphene are studied by X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectra and electrochemical measurements. The results reveal that the graphene sheets not only form a compact and uniform coating layer throughout the Li₃V₂(PO₄)₃/C, but also stretch out and cross‐link into a conducting network around the Li₃V₂(PO₄)₃/C particles. Thus, the graphene decorated Li₃V₂(PO₄)₃/C electrode exhibits superior high‐rate capability and long‐cycle stability. It delivers a reversible discharge capacity of 178.2 mAh·g^?1 after 60 cycles at a current density of 0.1 C, and the rate performances of 176, 169.3, 156.1 and 135.7 mAh·g^?1 at 1, 2, 5 and 10 C, respectively. The superior electrochemical properties make the graphene decorated Li₃V₂(PO₄)₃/C composite a promising cathode material for high‐performance lithium‐ion battery.     

长循环高电压钠离子电池正极材料P2-Na2/3Mn1/3Bi1/3Ni1/3O2的合成及性能

镍基层状氧化物NaNiO₂钠离子电池材料具有高电压和高容量的特性,且制备方法较为简单,但姜-泰勒(Jahn-Teller)效应使其在高倍率循环下容量较低以及在高电压(4.5 V)下无法稳定循环。通过调节溶胶-凝胶工艺的条件,设计、合成了Na_2/3Mn_1/3Bi_1/3Ni_1/3O₂片层状金属氧化物,并将其作为正极活性材料,在空气环境中组装成钠离子电池,进行电化学测试,考察Bi、Mn掺入量对电池电化学影响。研究结果表明：当金属Mn和Bi共掺时,在1.2~4.5 V宽电压范围内,电池在循环50周后容量为90.39 mAh·g^-1。在2.0~4.0 V电压范围内1.0C (115 mA·g^-1)倍率下恒流充放电50周后的容量保持率为96.96%,循环850周后的保持率为80.15%,具有良好的循环稳定性和安全性。     

长循环高电压钠离子电池正极材料P2-Na2/3Mn1/3Bi1/3Ni1/3O2的合成及性能

镍基层状氧化物NaNiO₂钠离子电池材料具有高电压和高容量的特性,且制备方法较为简单,但姜-泰勒(Jahn-Teller)效应使其在高倍率循环下容量较低以及在高电压(4.5 V)下无法稳定循环。通过调节溶胶-凝胶工艺的条件,设计、合成了Na_2/3Mn_1/3Bi_1/3Ni_1/3O₂片层状金属氧化物,并将其作为正极活性材料,在空气环境中组装成钠离子电池,进行电化学测试,考察Bi、Mn掺入量对电池电化学影响。研究结果表明：当金属Mn和Bi共掺时,在1.2~4.5 V宽电压范围内,电池在循环50周后容量为90.39 mAh·g^-1。在2.0~4.0 V电压范围内1.0C (115 mA·g^-1)倍率下恒流充放电50周后的容量保持率为96.96%,循环850周后的保持率为80.15%,具有良好的循环稳定性和安全性。