Room temperature transparent conducting oxides based on zinc oxide thin films

Doped zinc oxide thin films are grown on glass substrate at room temperature under oxygen atmosphere, using pulsed laser deposition (PLD). O₂ pressure below 1 Pa leads to conductive films. A careful characterization of the film stoichiometry and microstructure using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) concludes on a decrease in crystallinity with Al and Ga additions (≤3%). The progressive loss of the (0 0 2) orientation is associated with a variation of the c parameter value as a function of the film thickness and substrate nature. ZnO:Al and ZnO:Ga thin films show a high optical transmittance (>80%) with an increase in band gap from 3.27 eV (pure ZnO) to 3.88 eV and 3.61 eV for Al and Ga doping, respectively. Optical carrier concentration, optical mobility and optical resistivity are deduced from simulation of the optical data.     

Influence of polarity inversion on the electrical properties of Ga‐doped ZnO thin films

This study investigates how polarity inversion influences the relationship between the electrical properties of heavily Ga‐doped ZnO (GZO) films deposited by RF magnetron sputtering and their thickness. The electrical properties observed in very thin films are correlated with a change of polarity from O‐polar to Zn‐polar face upon increasing the film thickness based on results of valence band spectra measured by X‐ray photoelectron spectroscopy. It is found that the electrical properties of very thin GZO films deposited on Zn‐polar ZnO templates are significantly improved compared to those deposited on O‐polar face. A low resistivity of 2.62 × 10^–4 Ω cm, high Hall mobility of 26.9 cm²/V s, and high carrier concentration of 8.87 × 10²⁰ cm^–3 being achieved with 30 nm‐thick GZO films using Zn‐polar ZnO templates on a glass substrate. In contrast, the resistivity of 30 nm‐thick GZO films on bare glass that shows more likely O‐polar is very poor about 1.44 × 10^–3 Ω cm with mobility and carrier concentration are only 11.9 cm²/V s and 3.64 × 10²⁰ cm^–3, respectively. It is therefore proposed that polarity inversion plays an important role in determining the electrical properties of extremely thin GZO films. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Nitrogen oxides and ammonia sensing characteristics of SILAR deposited ZnO thin film

Pure and Sn, Ni doped ZnO thin films were deposited on glass substrates using a novel successive ionic layer adsorption and reaction (SILAR) method at room temperature. Microstructures of the deposited films were optimized by adjusting growth parameters. The variation in resistivity of the ZnO film sensors was performed with rapid photothermal processing (RPP). The effect of rapid photothermal processing was found to have an important role in ZnO based sensor sensitivity to NO₂, NH₃. While the undoped ZnO film surface exhibited higher NH₃ sensitivity than that of NO₂, an enhanced NO₂ sensitivity was noticed for the ZnO films doped with Sn and higher NH₃ sensitivity was obtained by Ni doping.     

Effects of hydrogen flow on properties of hydrogen doped ZnO thin films prepared by RF magnetron sputtering

The hydrogen doped ZnO (ZnO:H) thin films were deposited on quartz glass substrates by radio frequency magnetron sputtering. The doping characteristics of ZnO:H thin films with varied hydrogen flow ratio were investigated. At low hydrogen flow ratio (H₂/(H₂+Ar)≤0.02), the ZnO:H thin films exhibited dominant (002) peaks from X-ray diffraction and the lattice constants became smaller. The particles were mainly a columnar structure. The particles’ size became smaller, and the island-like structure appeared on the thin films surface. In addition, the low resistivity properties of ZnO:H thin films was ascribed to the increase of the carriers concentration and carriers mobility; When the hydrogen flow ratio was more than 0.02 (M≥0.02), two absorption bands at 1400–1800 cm^?1 and 3200–3900 cm^?1 were observed from the FT-IR spectra, which indicated that the ZnO:H thin films had typical Zn–H bonding, O–H bonding (hydroxyl), and Zn–H–O bonding (like-hydroxyl). The scanning electron microscope (SEM) results show that a large number of hydroxyl agglomeration formed an island-like structure on the thin films surface. The absorption peak at about 575 cm^?1 in the Raman spectra indicated that oxygen vacancies (V_O) defects were produced in the process of high hydrogen doping. In this condition, the low resistivity properties of ZnO:H thin films were mainly due to the increasing electron concentration resulted from V_O. Meanwhile, the Raman absorption peaks at approximately 98 cm^?1 and 436 cm^?1 became weaker, and the (002) XRD diffraction peak quenched and the lattice constants increased, which shows that the ZnO:H thin films no longer presented a typical ZnO hexagonal wurtzite structure. With the increasing of hydrogen flow ratio, the optical transmittance of ZnO:H thin films in the ultraviolet band show a clear Burstein–Moss shift effect, which further explained that electron concentration was increased due to the increasing V_O with high hydrogen doping concentration. Moreover, the optical reflectance of the thin films decreased, indicating the higher roughness of the films surface. It was noteworthy that etching effect of H plasma was obvious in the process of heavy hydrogen doping.     

Electrical and optical properties of Ga doped zinc oxide thin films deposited at room temperature by continuous composition spread

Ga doped ZnO (GZO) thin films were deposited on glass substrates at room temperature by continuous composition spread (CCS) method. CCS is thin films growth method of various Ga_xZn_1−xO(GZO) thin film compositions on a substrate, and evaluating critical properties as a function position, which is directly related to material composition. Various compositions of Ga doped ZnO deposited at room temperature were explored to find excellent electrical and optical properties. Optimized GZO thin films with a low resistivity of 1.46 × 10⁻³ Ω cm and an average transmittance above 90% in the 550 nm wavelength region were able to be formed at an Ar pressure of 2.66 Pa and a room temperature. Also, optimized composition of the GZO thin film which had the lowest resistivity and high transmittance was found at 0.8 wt.% Ga₂O₃ doped in ZnO.     

Growth characteristics and properties of ZnO:Ga thin films prepared by pulsed DC magnetron sputtering

Transparent conductive ZnO:Ga thin films were deposited on Corning 1737 glass substrate by pulsed direct current (DC) magnetron sputtering. The effects of process parameters, namely pulse frequency and film thickness on the structural and optoelectronic properties of ZnO:Ga thin films are evaluated. It shows that highly c-axis (0 0 2) oriented polycrystalline films with good visible transparency and electrical conductivity were prepared at a pulsed frequency of 10 kHz. Increasing the film thickness also enlarged the grain size and carrier mobility which will subsequently lead to the decrease in resistivity. In summary, ZnO:Ga thin film with the lowest electrical resistivity of 2.01 × 10⁻⁴ Ω cm was obtained at a pulse frequency of 10 kHz with 500 nm in thickness. The surface RMS (root mean square) roughness of the film is 2.9 nm with visible transmittance around 86% and optical band gap of 3.83 eV.     

Electronic and optical properties in ZnO:Ga thin films induced by substrate stress

The effects of biaxial stress in ZnO:Ga thin films on different substrates, e.g., sapphire(0001), quartz, Si(001), and glass have been investigated by X-ray diffraction, atomic force microscopy, and electrical transport and ellipsometric measurements. A strong dependence of orientation, crystallite size, transport, and electronic properties upon the substrate-induced stress has been found. The structural properties indicate that a tensile stress exists in epitaxial ZnO:Ga films grown on sapphire, Si, and quartz, while a compressive stress appears in films grown on glass. The resistivity of the films decreased with increasing biaxial stress, which is inversely proportional to the product of the carrier concentration and Hall mobility. The refractive index n was found to decrease with increasing biaxial stress, while the optical band gap E₀ increased with stress. These behaviors are attributed to lattice contraction and the increase in the carrier concentration that is induced by the stress. Our experimental data suggest that the mechanism of substrate-induced stress is important for understanding the properties of ZnO:Ga thin films and for the fabrication of devices which use these materials.     

Electrical properties of Sb-doped epitaxial SnO2 thin films prepared using excimer-laser-assisted metal–organic deposition

Excimer-laser-assisted metal–organic deposition (ELAMOD) was used to prepare Sb-doped epitaxial (001) SnO₂ thin films on (001) TiO₂ substrates at room temperature. The effects of laser fluence, the number of shots with the laser, and Sb content on the electrical properties such as resistivity, carrier concentration, and carrier mobility of the films were investigated. The resistivity of the Sb-doped epitaxial (001) SnO₂ thin film prepared using an ArF laser was lower than that of the film prepared using a KrF laser. The van der Pauw method was used to measure the resistivity, carrier concentration, and carrier mobility of the Sb-doped epitaxial (001) SnO₂ thin films in order to determine the effect of Sb content on the electrical resistivity of the films. The lowest resistivity obtained for the Sb-doped epitaxial (001) SnO₂ thin films prepared using ELAMOD with the ArF laser and 2 % Sb content was 2.5 × 10^?3 Ω cm. The difference between the optimal Sb concentrations and resistivities of the films produced using either ELAMOD or conventional thermal MOD was discussed.     

Effects of H2 ambient annealing in fully 0 0 2-textured ZnO:Ga thin films grown on glass substrates using RF magnetron co-sputter deposition

Gallium doped zinc oxide (ZnO:Ga) thin films were grown on glass substrates using RF magnetron co-sputtering, followed by H₂ ambient annealing at 623 K to explore a possibility of steady and low-cost process for fabricating transparent electrodes. While it was observed that the ZnO:Ga thin films were densely packed c-axis oriented self-textured structures, in the as-deposited state, the films contained Ga₂O₃ and ZnGa₂O₄ which had adverse effect on the electrical properties. On the other hand, post-annealing in H₂ ambient improved the electrical properties significantly via reduction of Ga₂O₃ and ZnGa₂O₄ to release elemental Ga which subsequently acted as substitutional dopant increasing the carrier concentration by two orders of magnitude. Transmittance of the ZnO:Ga thin films were all over 90% that of glass while the optical band gap varied in accordance with the carrier concentrations due to changes in Fermi level. Experimental observation in this study suggests that transparent conductive oxide (TCO) films based on Ga doped ZnO with good electrical and optical properties can be realized via simple low-cost process.     

Synthesis and characterization of Al-N codoped p-type ZnO epitaxial films using high-temperature homo-buffer layer

Al-N codoped p-type ZnO thin films have been prepared by DC magnetron reactive sputtering reproducibly using a high-temperature (HT) homo-buffer layer. The influence of HT buffer layer deposition time (T_ht) on film properties was investigated by X-ray diffraction (XRD), scanning electron micro-spectra (SEM) and Hall measurement. The Al-N codoped ZnO film was improved evidently in its crystal quality by varying the value of T_ht. Results of Hall effect showed that all of the Al-N codoped ZnO thin films were p-type conduction and had resistivity mainly below 50 Ω cm. The optimum deposition time of HT buffer layer is around 3 min from the comprehensive consideration of structural, electrical, and optical properties. The obtained ZnO thin film can meet the need of application in optoelectronic devices based on ZnO.     

Improvement of electrical and optical properties of Ga and N co-doped p-type ZnO thin films with thermal treatment

Ga and N co-doped p-type ZnO thin films were epitaxially grown on sapphire substrate using magnetron sputtering technique. The process of synthesized Ga and N co-doped ZnO films was performed in ambient gas of N₂O. Hall measurement shows a significant improvement of p-type characteristics with rapid thermal annealing (RTA) process in N₂ gas flow, where more N acceptors are activated. The film rapid thermal annealed at 900 °C in N₂ ambient revealed the highest carrier concentration of 9.36 × 10¹⁹ cm⁻³ and lowest resistivity of 1.39 × 10⁻¹ Ω cm. In room and low temperature photoluminescence measurements of the as grown and RTA treated film, donor acceptor pair emission and exciton bound to acceptor recombination at 3.25 and 3.357 eV, respectively, were observed.     

Effect of solution concentration on physicochemical and gas sensing properties of sprayed WO3 thin films

Sub-stoichiometric tungsten trioxide (WO₃) thin films are deposited onto the glass substrates by spray pyrolysis technique using ammonium metatungstate. Effect of solution concentration on structural, morphological, optical, electrical and NO₂ sensing properties of WO₃ thin films is studied. Films are polycrystalline with monoclinic crystal structure and sub-stoichiometric as observed form the XRD and XPS studies, respectively. The SEM and AFM images show micro grained structure and surface roughness increases with increase in solution concentration. The PL studies revealed that the majority of the defects are the oxygen vacancies. From XPS and PL studies it is observed that, oxygen vacancies decrease with increase in solution concentration. The dielectric constant of the films as a function of frequency is in concurrence with resistivity measurements. Films show reproducible and reversible gas response at various operating temperatures and gas concentrations. Highest sensor response (38%) towards 200 ppm NO₂ concentration is observed for the film with 15 mM solution concentration at moderate operating temperature (200 °C). Pd sensitization enhanced gas response to 68% and improved kinetics of the sensor. Films are highly selective towards NO₂ as compared with the various gases such as SO₂, LPG, NH₃ and H₂S.     

氢气引入对宽光谱Mg和Ga共掺杂ZnO透明导电薄膜的特性影响

为适应宽光谱高效率硅基薄膜太阳电池的应用需求,本文尝试采用直流磁控溅射技术在553 K衬底温度下生长氢化Mg和Ga共掺杂ZnO(HMGZO)透明导电氧化物(TCO)薄膜.通过对薄膜微观结构、表面形貌、电学以及光学性能的测试和分析,详细地研究了氢气(H2)流量(0—16.0 sccm)对HMGZO薄膜结晶特性及光电性能的影响.实验结果表明:生长获得的HMGZO薄膜均为六角纤锌矿结构的多晶薄膜,择优取向为(002)晶面生长方向.薄膜的生长速率随着氢气流量的增加呈现逐渐减小趋势,主要归因于溅射产额的减小.适当的氢气引入会引起晶粒尺寸的增加.随着氢气流量由0增加至4.0 sccm,ZnO薄膜电阻率从177?·cm急剧减小至7.2×10-3?·cm,主要是由于H施主的引入显著地增加了载流子浓度;然而进一步增加氢气流量(4.0—16.0 sccm)造成电阻率的轻微增加,主要归因于载流子浓度的减小以及过多氢杂质引入造成杂质散射的增加.所有生长获得的HMGZO薄膜平均光学透过率在波长λ～320—1100 nm范围内可达87%以上.由于Mg的作用及Burstein-Moss效应的影响造成了带隙展宽,带隙变化范围～3.49—3.70 eV,其中最大光学带隙Eg可达～3.70 eV.     

Preparation of Bi2S3 thin films with a nanoleaf structure by electrodeposition method

Nanoleaf-like Bi₂S₃ thin films were deposited on indium tin oxide (ITO) glass using Bi(NO₃)₃ and Na₂S₂O₃ as precursors by a cathodic electrodeposition process. The as-deposited thin films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and photoluminescence spectrum (PL). The influence of precursor solution mole concentration ratios [Bi(NO₃)₃]/[Na₂S₂O₃] on the phase compositions, morphologies and photoluminescence properties of the obtained thin films were investigated. Results show that a uniform Bi₂S₃ thin film with nanoleaf structure can be obtained with the precursor solution concentration ratio [Bi(NO₃)₃]/[Na₂S₂O₃] = 1:7. The as-prepared thin films exhibit blue-green photoluminescence properties under ultraviolet light excitation. With the increase of concentration ratios [Bi(NO₃)₃]/[Na₂S₂O₃] in the deposition solution, the crystallizations and PL properties of Bi₂S₃ thin films are obviously improved.     

I–V characteristics of ZnO/Cu2O thin film n–i–p heterojunction

ZnO/Cu₂O thin film n–i–p heterojunctions were fabricated by magnetron sputtering. The microstructure, optical, and electrical properties of n-type (n‐) ZnO, insulating (i‐) ZnO, and p-type (p‐) Cu₂O films deposited on glass substrates were characterized by X-Ray diffraction (XRD), spectrophotometer, and the van der Pauw method, respectively. XRD results show that the mean grain size of i-ZnO film is much larger than that of n-ZnO film. The optical band gap energies of n-ZnO, i-ZnO, and p-Cu₂O film are 3.27, 3.47, and 2.00 eV, respectively. The carrier concentration of n-ZnO film is two orders of magnitude larger than that of p-Cu₂O film. The current–voltage (I–V) characteristics of ZnO/Cu₂O thin film n–i–p heterojunctions with different i-ZnO film thicknesses were investigated. Results show that ZnO/Cu₂O n–i–p heterojunctions have well-defined rectifying behavior. All ideality factors of these n–i–p heterojunctions are larger than 2.0. The forward bias threshold voltage and ideality factor increase when i-ZnO layer thickness increases from 100 to 200 nm. An energy band diagram was proposed to analyze the I–V characteristics of these n–i–p heterojunctions.     

Ferromagnetism in noncompensated (Mn,Ga)-codoped ZnO films

Mn/Ga noncompensated codoped ZnO films were prepared on c-cut sapphire substrates via pulsed laser deposition. The structural, magnetic, transport, and optical properties of the films were then investigated. Addition of the Ga donor increases the electron concentration and enhances the magnetization in these films because of the net negative charge of the special noncompensated codoping, which can adjust the carrier concentration as well as the magnetic moment. Moreover, the Fermi level moves into the conduction band because of the increase in electron concentration, which results in an increase in the optical band gap value, from 3.28 eV for the undoped ZnO film to 3.61 eV for the (Mn,Ga)-codoped ZnO film.     

Microstructure and polarity of epitaxial ZnO films grown on LSAT(111) substrate studied by transmission electron microscopy

Transmission electron microscopy is used to investigate the structural characteristics of epitaxial ZnO thin films grown on (LaAlO₃)_0.3(Sr_0.5Ta_0.5O₃)_0.7(111) (LSAT) by rf plasma-assisted molecular beam epitaxy. It is found that the growth temperature plays a key role in the formation of microstructures in ZnO film. Growth temperature dependence of rotation domain, interface and dislocation structures is studied, and the mechanism for polarity selection is discussed.     

Investigation of electrical and optical properties of ZnO thin films grown with O<Subscript>2</Subscript>/O<Subscript>3</Subscript> gas mixture

The electrical and optical properties of ZnO thin films grown with an O₂/O₃ gas mixture are compared with samples grown with pure oxygen gas. The ZnO films were grown on sapphire(0001) by pulsed laser deposition. The residual background carrier concentration is reduced by using an O₂/O₃ gas mixture as compared to pure molecular oxygen. In particular, a one order of magnitude reduction in residual background carrier density (6.15×10¹⁶ cm^-3) is achieved by using an O₂/O₃ gas mixture. The lower donor defect density is attributed to the generation of acceptor defects compensating for the residual donor defects. Photoluminescence results show that the deep level emission increased and the band edge emission decreased for the ZnO films grown with ozone, as compared to the samples grown with pure oxygen gas. PACS 73.61.Ga; 78.55Et; 81.05 Dz; 81.15.Fg     

Electronic transport and carrier concentration in conductive ZnO:Ga thin films

Transparent and conductive Ga-doped ZnO (ZnO:Ga) films were post-annealed after sputter deposition, and their structural and electrical properties were investigated. Post-annealing led to an improvement of crystallinity along the [001] direction, but did not change lateral grain size. Therefore, carrier concentration and electron mobility of films were analyzed as a function of crystallinity. The electrical parameters were obtained with both optical reflectance based on the Drude free-electron model and the Hall method, and similar tendencies were observed within the two methods. Even though the lowest resistivity was demonstrated by the film annealed at 550 °C, the optimum values for carrier concentration and mobility were observed in films with different post-annealing temperatures.     

Electrostatic spray deposited zinc oxide films for gas sensor applications

In this work, thin films of zinc oxide (ZnO) for gas-sensor applications were deposited on platinum coated alumina substrate, using electrostatic spray deposition (ESD) technique. As precursor solution zinc acetate in ethanol was used. Scanning electron microscopy (SEM) evaluation showed a porous and homogeneous film morphology and the energy dispersive X-ray analysis (EDX) confirmed the composition of the films with no presence of other impurities. The microstructure studied with X-ray diffraction (XRD) and Raman spectroscopy indicated that the ZnO oxide films are crystallized in a hexagonal wurtzite phase. The films showed good sensitivity to 1 ppm nitrogen dioxide (NO₂) at 300 °C while a much lower sensitivity to 12 ppm hydrogen sulphide (H₂S).