The role of complexing ligands in the formation of non-aggregated nanoparticles of zirconia

The hydrolysis and condensation of zirconium n-propoxide in n-propanol have been chemically controlled via the complexation of the zirconium precursor with acetylacetone. The size of the zirconium oxide-based particles is mainly controlled by the complexation ratio x=[acac]/[Zr]. the mean size increases from nanometric to submicronic range when x decreases from 1 to 0.1. Amorphous colloidal particles are obtained at room temperature. They result from a competitive growth/termination mechanism of zirconium-oxo species in the presence of acac surface capping agents. However non-aggregated nanocrystalline particles of tetragonal zirconia, about 2 nm in diameter are formed upon aging at 60°C when hydrolysis is performed in the presence of paratoluene sulfonic acid (PTSA).     

Synthesis and Characterization of Sol-Gel Cu-ZrO2 and Fe-ZrO2 Catalysts

Fe-ZrO₂ and Cu-ZrO₂ xerogels were prepared by a sol-gel method. The effect of the hydrolysis catalyst during the gelation step, namely H₂SO₄ or NH₄OH, on the properties of the resulting materials was investigated by XRD, BET, TGA/DTA, TPD of ammonia, FTIR, and TPR. Fe-ZrO₂ and Cu-ZrO₂ xerogels, with sulfuric acid introduced as the hydrolysis catalyst, mainly crystallyzed in the tetragonal phase and exhibited larger surface area and acid amount than those obtained with NH₄OH. Ammonia TPD shows that copper promoted sulfated zirconia is the most acidic material. TGA and FTIR reveal that under oxidizing conditions sulfated zirconia promoted with iron and copper retains more sulfate species than unpromoted sulfated zirconia. Regardless of the hydrolysis catalyst employed, copper promoted catalysts calcined at 600°C, contain a large fraction of copper oxide specieseasily reduced at low temperatures. These copper oxide species are believed to have different environment and interactions with the surface oxygen vacancies of the zirconia support. A FeO-like phase appears to be the most probable one after reduction of Fe-ZrO₂ catalysts prepared with NH₄OH as the hydrolysis catalyst. The formation of Fe° species may be hindered by the high dispersion and interaction of Fe²⁺ ions with the zirconia support. On the other hand, the reduction peaks of iron oxide and sulfate species exhibit a considerable overlap in the TPR profiles of sulfated Fe-ZrO₂ samples. Hence, the nature of the supported phase in the latter samples is rather uncertain.     

Thermally Induced Phase Transformation on 12-Tungstophosphoric Acid/ZrO2 Sol-Gel

Zirconium (IV)-n-butoxide and tungstophosphoric acid (WP) were co-gelled at pH 3, 5 and 7 with HCl acid, C₂H₄O₂ acid and NH₄OH, respectively. Pyridine adsorption bands at 1610 and 1442 cm^–1 corresponding to Lewis acidic sites were observed by FTIR spectroscopy. Acidity determined by ammonia thermodesorption shows values around 1100 mol of NH₃/g, which correspond to solids showing super acidity. It was found that the incorporation of WP to gelling zirconia delay the formation of tetragonal zirconia. Raman spectroscopy shows the stabilization of the Keggin structure on zirconia thermally treated at 400°C.     

Coating of oxide powders with alkoxide derived zirconia

Coating of alumina powders with tetragonal zirconia grains in the nanometric size range was obtained from a modified zirconium n-propoxide sol.Powder sedimentation observations and washing experiments were performed to show modifications of particles surface. Amorphous precursor film formation and crystalline zirconia coating were characterized by transmission electron microscopy. Crystallographic relationships between zirconia and alumina particles were also observed.     

High-resolution transmission electron microscopy investigation of nanostructures in SnO2 thin films prepared by pulsed laser deposition

Pulsed laser deposition (PLD) was used to grow nanocrystalline SnO₂ thin films onto glass substrates. The nanocrystallites and microstructures in SnO₂ thin films grown by PLD techniques have been investigated in detail by using X-ray diffraction and high-resolution transmission electron microscopy (HRTEM). The PLD process was carried out at room temperature under a working pressure of about 2×10⁻⁶ mbar. Experimental results indicate that thin films are composed of a polycrystalline SnO₂ and an amorphous SnO phase. In particular, the presence of such an amorphous SnO phase in the thin films greatly limits their practical use as gas-sensing devices. HRTEM observations revealed that SnO₂ nanocrystallites with tetragonal rutile structure embed in an amorphous SnO matrix, which are approximatively equiaxed. These approximatively equiaxed SnO₂ nanocrystallites contain a high density of defects, such as twin boundaries and edge dislocations. The grain growth of SnO₂ thin films may be discussed in terms of the coalescent particle growth mechanism.     

Synthesis and photocatalytic performances of BiVO4 by ammonia co-precipitation process

This paper reports the preparation and photocatalytic performance of Bismuth vanadate (BiVO₄) by a facile and inexpensive approach. An amorphous BiVO₄ was first prepared by a co-precipitation process from aqueous solutions of Bi(NO₃)₃ and NH₄VO₃ using ammonia. Followed by heating treatment at various temperatures, the amorphous phase converted to crystalline BiVO₄ with a structure between monoclinic and tetragonal scheelite. The crystallization of BiVO₄ occurred at about 523 K, while the nanocrystalline BiVO₄ were formed with a heat-treatment of lower than 673 K. However, when the heat-treatment was carried out at 773 K, the accumulation of nanocrystals to bulk particles was observed. The photocatalytic performances of the materials were investigated by O₂ evolution under visible-light, and MB decomposition under solar simulator. The results demonstrated that the crystalline structure is still the vital factor for the activities of both reactions. However, the crystallinity of BiVO₄ gives a major influence on the activity of O₂ evolution, whereas the surface area, plays an important role for photocatalytic MB decomposition.     

Planar ZrO2 Waveguides Prepared by the Sol-Gel Process: Structural and Optical Properties

ZrO₂ waveguides are prepared by the sol-gel process from a solution containing zirconiumn-propoxide and acetylacetone in propanol-2. Structural characterizations are investigated for different annealing temperatures using suitable techniques including Waveguide Raman Spectroscopy, Electron Microscopy and Atomic Force Microscopy. Films are amorphous at 300°C and the pure ZrO₂ tetragonal crystalline phase appears beyond 400°C. Crystallized films present a dense, uniform and polycrystalline structure made up by randomly oriented nanocrystallites, the diameter of which increases from 38 Å at 400°C to 53 Å at 600°C. Waveguides are at least monomode TE₀ at 632.8 nm. At this wavelength, optical losses are about, 0.8±0.2dB/cm for amorphous layers and increase up to 2.5±0.4 dB/cm for 600°C heat-treated waveguides.     

Kinetic study of zirconia crystallization from amorphous ZrO2-SiO2 composite precursors processed by sol-gel chemistry

Powder precursor gels with composition xZrO₂·(100–x)SiO₂, with selected values of x=8, 24, 43 and 75 mol%, were processed by sol-gel chemistry. Differential thermal analysis (DTA) was used to study crystallization in (cubic/tetragonal)-ZrO₂ during the heating of the reactive amorphous precursors. Kinetic parameters such as activation energy, Avrami's exponent and frequency factor have been simultaneously calculated from the computed DTA data using a previously reported kinetic model. The crystallization temperature decreases relative to the increase in the amount of ZrO₂, the value of the kinetic parameter of the crystallization being related to the value of x.     

ZrO<Subscript>2</Subscript> and Cu/ZrO<Subscript>2</Subscript> Sol–Gel Materials Spectroscopic Characterization

Copper-doped zirconia (1% mol) and zirconia powders were prepared by the sol–gel process, using zirconium n-butoxide and copper nitrate as precursors. The resulting xerogels are nanocrystalline and exhibit different properties from the corresponding microcrystalline materials. The copper nitrate salt was dissolved and co-gelled in situ at the initial stage of the reaction. The properties of the resulting materials were studied by XRD, FTIR and UV-Vis. The as-prepared samples were amorphous and crystallized to the tetragonal zirconia phase at 400 °C. At temperatures higher than 600 °C, the monoclinic phase was also obtained. No evidence of discrete crystalline copper compounds was observed, consistent with good dispersion of the dopant. Several bands were observed by FTIR in the 4400–3000 cm^–1 region, which diminishes in intensity and shifted to higher wavenumbers with heating. The bandgap energy (E_g) was strongly modulated by the presence of the dopant and heating temperature, with increasing temperature leading to a corresponding decrease in E_g.     

Phase evolution of sol-gel CaO-ZrO2 using sulfuric acid as hydrolysis catalyst

Several compositions in the CaO-ZrO₂ system were synthesized from zirconium n-butoxide and calcium methoxide, by the sol-gel method. Hydrolysis and gelation occurred at pH 3, using H₂SO₄ as hydrolysis catalyst. Fresh gels were annealed in air at 100 to 900°C, in 100°C steps every 20 h, for a total annealing time of 140 h. Analysis by X-ray diffraction showed the formation of hydrated calcium sulfate together with amorphous zirconia up to 400°C. At the ZrO₂ rich-end, tetragonal and monoclinic zirconia solid solutions were stabilized in the presence of Ca ions. When 20 and 30 wt% of CaO were added, cubic zirconia and CaZrO₃ solid solutions were observed above 700°C. At the CaO rich-end, the coexistence of calcium carbonate polymorphs as vaterite and calcite were observed. Anhydrite was present across the entire range of compositions studied from 300 to 900°C.     

Atomic-Scale Structure of Water-Based Zirconia Xerogels by X-Ray Diffraction

The structural evolution of zirconia thin films and gel powders has been evaluated by X-ray diffraction. Maxima (r ₁ and r ₂) of the experimental radial distribution function RDF and the bond angles were determined and correlated with TGA (thermogravimetric analysis), DTA (differential thermal analysis) and MS (mass spectrometry). The results indicate that the topological short-range structure (<5 Å) of amorphous zirconia thin films, independent of drying temperature, resembles that of crystalline tetragonal ZrO₂. In contrast, amorphous zirconia powder gels dried at temperatures below 120°C show atomic arrangements similar to that of tetragonal ZrO₂. The structure of these gels annealed at temperatures between 165–340°C resembles a distorted tetragonal ZrO₂, monoclinic-like structure. Zirconia powders and films contain crystalline tetragonal ZrO₂ at 400°C.     

Solid Solutions of WO3into Zirconia in WO3-ZrO2 Catalysts

Catalysts in the WO₃-ZrO₂ system were produced by coprecipitation of aqueous solutions of zirconium oxynitrate and ammonium metatungstate. Samples were characterized by X-ray powder diffraction, thermogravimetry, and refinement of their crystalline structures with the Rietveld method. This coprecipitation gave rise to solid solutions of tungsten oxide into zirconia; the initial phase was amorphous and crystallized into two tetragonal crystalline phases, T1 and T2, when samples were annealed at 560°C. The main difference between both phases was the oxygen position along the c axis. In the phase with higher symmetry, T2, an oxygen atom was at one-half of the unit cell, 0.50(2), producing flat crystallite surfaces perpendicular to the c axis, while in the phase with the lower symmetry, T1, it was at 0.447(2), and gave rise to rough crystallite surfaces parallel to (100) planes. The interpenetrating tetrahedra forming the representative polyhedron of the crystalline structure were almost nondeformed in the phase with higher symmetry, because all Zr-O atom bond lengths were very similar. As the annealing temperature of the sample was increased, the dissolved tungsten atoms in the phase with higher symmetry segregated to the crystallite's surface.     

立方晶型Sb2O3纳米晶的合成及光催化性能

采用沉淀法合成了立方晶型Sb2O3纳米晶,通过X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)和电子自旋共振谱(ESR)等对样品进行了详细的表征。以紫外光光催化降解甲基橙为反应模型评价了样品的光催化性能。结果表明:沉淀法合成的立方晶型Sb2O3纳米晶颗粒小,表现出良好的光催化性能。对立方晶型Sb2O3纳米晶光催化降解甲基橙的原因进行了探讨,并提出了降解甲基橙的反应机理。     

IR Spectroscopic Investigations of Gasochromic and Electrochromic Sol-Gel—Derived Peroxotungstic Acid/Ormosil Composite and Crystalline WO3 Films

We studied the gasochromic effect of amorphous peroxopolytungstic acid (W-PTA), W-PTA (ormosil) and crystalline WO₃ films. These latter films were prepared after a heat treatment of W-PTA/ormosil films at 450°C. The ormosil served as a template, providing the monoclinic WO₃ films with adequate porosity. The spill-over effect was attained by impregnating the porous WO₃ crystalline films with H₂PtCl₆ followed by a heat treatment at 380°C. The amorphous films became gasochromic with the addition of PdCl₂ to the corresponding W-PTA and W-PTA/ormosil sols.Structural features of all the films were studied with the help of infrared (IR) spectroscopy and transmission electron microscopy (TEM). In situ IR spectra of the films, performed in the presence of reducing (H₂/Ar) and oxidising (O₂/Ar) gases, revealed a reversible transformation of the monoclinic to the tetragonal H _x WO₃ phase. At the same time the coloration (reduction) of the amorphous films was accompanied by the formation of coordinated water molecules and increased numbers of W=O bonds. Gasochromic colouring/bleaching changes and the corresponding kinetics were assessed from in situ UV-visible transmission measurements on the films.     

Preparation and Characterization of Amorphous ZrO2-SiO2 Composite Powders Processed by Sol-Gel Chemistry

Composite ZrO₂-SiO₂ powders, with different ZrO₂ contents, including pure ZrO₂ powders, were prepared by precipitation in SiO₂ suspensions, of zirconia gels from solutions of zirconyl chloride at pH = 11. These products were investigated in connection with the phase changes in ZrO₂ caused by heat-treatments. ZrO₂-SiO₂ mixtures containing 0–100% mol ZrO₂, were studied by differential thermal analysis (DTA), X-ray powder diffraction (XRD), temperature programmed desorption combined with mass spectroscopy (TPD-MS), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX), to obtain information on the morphological and structural features of the particles before and during the heat treatment up to 1200°C. Specific surface areas were determined using nitrogen adsorption by the BET method. The results offer an explanation about some of the factors which can be influencing on the stabilization of metastable-cubic/tetragonal (C/T) phase of ZrO₂ and the evolution of surface areas (vulcano profile) observed in the composites.     

New Ion Conductor of (Ba1−xLax)2In2O5+x

The structural characterization, thermogravimetric analysis and electrical properties for solid solution system, (Ba_1–xLa_x)₂In₂O_5+x with perovskite-type structure were investigated. X-ray diffraction showed that the orthorhombic phase was in the range of 0.0<x0.3, the tetragonal phase 0.3<x0.5, and the cubic phase 0.5<x. The sharp transition of electrical conductivity shifted to a lower temperature with increasing x and disappeared at the phase boundary between the orthorhombic and tetragonal phases. This perovskite-related oxide exhibited a pure oxide-ion conduction over the oxygen partial pressure range of 1 atm to 10^–3.5 atm, and the electrical conductivity reached the value of 1.610^–1 (S cm^–1) at 1073 K, which was nearly equal to that of the yttria stabilized zirconia. These properties were successfully explained in terms of disordered oxygen ions.This revised version was published online in November 2005 with corrections to the Cover Date.     

Time‐Resolved Phase Transitions of the Nanocrystalline Cubic to Submicron Monoclinic Phase in Mn2O3‐ZrO2

The nanocrystalline cubic phase of zirconia was found to be thermally stabilized by the addition of 3 to 40 mol % manganese. The nanocrystalline cubic, tetragonal and monoclinic phases of zirconia stabilized with manganese (III)oxide (Mn‐Stabilized Zirconia) were prepared by thermal decomposition of carbonate and hydroxide precursors. Both the crystallization and isothermal phase transitions associated with Mn‐SZ were studied using high temperature x‐ray diffraction and x‐ray diffraction of quenched samples. Cubic Mn‐SZ initially crystallized and progressively transformed to tetragonal, and monoclinic structures above 700°C. The nanocrystalline cubic Mn‐SZ containing 25 mol % Mn was found to have the greatest thermal stability, retaining its cubic form at temperatures as high as 800°C for periods up to 25 hours. Higher than 40 mol %, cubic Mn₂O₃ was found to coexist with cubic Mn‐SZ. The crystallite sizes observed for the cubic, tetragonal and monoclinic Mn‐SZ phases ranged from 50 to 137, 130 to 220, and 195 to 450 Å respectively, indicating, for ZrO₂, that particle size was a primary factor in determining its polymorphs. The classical Avrami equation for nucleation and growth was applied to the observed phase transformations.     

Photocatalytic activity of ZrO2 nanoparticles prepared by electrical arc discharge method in water

ZrO₂ nanoparticles were synthesized through arc discharge of zirconium electrodes in deionized (DI) water. X-ray diffraction (XRD) analysis of the as prepared nanoparticles indicates formation a mixture of nanocrystalline ZrO₂ monoclinic and tetragonal phase structures. Transmission electron microscopy (TEM) images illustrate spherical ZrO₂ nanoparticles with 7–30 nm diameter range, which were formed during the discharge process with 10 A arc current. The average particle size was found to increase with the increasing arc current. X-ray photoelectron spectroscopy (XPS) analysis confirms formation of ZrO₂ at the surface of the nanoparticles. Surface area of the sample prepared at 10 A arc current, measured by BET analysis, was 44 m²/g. Photodegradation of Rhodamine B (Rh. B) shows that the prepared samples at lower currents have a higher photocatalytic activity due to larger surface area and smaller particle size.     

Mechanism of formation of YBa2Cu4O8 superconductor in the sol-gel synthesis

It was shown that a single phase YBa₂Cu₄O₈ (124-phase) could be formed from gels at 1 atm oxygen pressure, and the mechanism of its formation was elucidated. It was found that there are two key routes for the sol-gel formation of the 124-phase, one involving the tetragonal YBa₂Cu₃O _y with a low concentration of oxygen defects (tetra-I phase) and the other involving the Ba₂Cu₃O_5.9 as important intermediates of the 124-phase. The rapid formation of these intermediate compounds from the gel was attributed to the small particle size of the oxides and carbonates precipitating at the initial stage of heating. It was thought that the small particles characteristic of sol-gel processing lead to the rapid formation of the intermediate compounds and subsequent precipitation of the 124-phase.