Preparation,Characterization and Properties of Reactive Type Dripping Agent Tween 60-IAH and Their Grafting Copolymer With Linear Low Density Polyethylene

A kind of reactive type dripping agent (Tween 60-IAH) was synthesized with polyethylene glycol sorbitan monostearate (Tween 60) and itaconic anhydride (IAH) as main starting materials. The chemical structure of Tween 60-IAH was characterized by means of Fourier transform infrared (FT-IR) spectroscopy. The effect of reaction time on conversion of Tween 60-IAH was studied. The results of thermogravimetric analysis (TGA) measurement demonstrated that Tween 60-IAH exhibited a better thermal stability than Tween 60. Grafting copolymer of linear low density polyethylene (LLDPE) with Tween 60-IAH was prepared in twin-screw extruder. Thermal and rheological properties of grafted LLDPE samples were investigated with differential scanning calorimetry (DSC) and rotational rheometer. Crystallization temperatures of grafted LLDPE were higher than that of LLDPE. Complex viscosities of grafted LLDPE at high shear rates were lower than that of LLDPE. The dripping properties of film samples were investigated at 60°C.     

Preparation and Properties of Polyether Pentaerythritol Mono‐maleate grafted Linear Low Density Polyethylene by Reactive Extrusion

A reactive type nonionic surfactant, polyether pentaerythritol mono‐maleate (PPMM) was synthesized in our laboratory. PPMM was adopted as a functionalizing monomer and grafted onto linear low density polyethylene (LLDPE) with a melt reactive extrusion procedure. FT‐IR was used to characterize the formation of grafting copolymer and evaluate their degree of grafting. The effects of monomer concentration, reaction temperature and screw run speed on the degree of grafting were studied systematically. Isothermal crystallization kinetics of LLDPE and LLDPE‐g‐PPMM samples was carried out using DSC. Crystallization rates of grafted LLDPE were faster than that of plain LLDPE at the same crystallization temperature. The tensile properties and light transmission of blown films were determined. Comparing with neat LLDPE film, no obvious changes could be found for the tensile strength, elongation at break and right angle tearing strength of LLDPE‐g‐PPMM film. The wettability is expressed by the water contact angle. With an increasing percentage of PPMM, the contact angles of water on film surface of LLDPE‐g‐PPMM decrease monotonically. The acceleration dripping property of film samples was investigated. The dripping duration of LLDPE‐g‐PPMM film and commercial anti‐fog dripping film at 60°C were 76 days and 17 days, respectively.     

Graft polymerization of arcylamide onto LLDPE film by electron beam pre-irradiation in air or argon. I. Influence of dose,grafting temperature,and monomer concentration

Linear low density polyethylene (LLDPE) film was irradiated by electron beam in air or argon prior to grafting in aqueous solutions of acrylamide containing 0.05% of Mohr's salt. The grafting kinetics was studied with pre-irradiation doses in the range of 2.5–25 Mrad and in the temperature range of 40–70°C. Grafting rates and final degrees of grafting were higher for LLDPE pre-irradiated in air than for LLDPE pre-irradiated in argon. The overall activation energies for the grafting reaction were dose-dependent. Above 5 Mrad, the overall activation energies were higher for LLDPE pre-irradiated in argon which is interpreted as being due to crosslinking of the LLDPE. © 1995 John Wiley & Sons, Inc.     

Adhesive effect of linear low-density polyethylene gels on polyethylene moldings

Adhesive effect of linear low density polyethylene (LLDPE) gels in organic solvents such as decalin, tetralin, and o-dichlorobenzene on high density polyethylene (HDPE) moldings has been investigated by shearing tests, and DSC measurements. For all of the gels the temperature at which the heated gel starts to exhibit the adhesive effect was about 70 °C, which is similar to the result of LDPE gel. In particular, when heated at 110 °C, LLDPE gel in tetralin showed such a strong bond strength that polyethylene plates of 3 mm in thickness and 20 mm in width gave rise to necking. It was found that LLDPE gel behaved as though it added LDPE gel to HDPE gel namely LDPE-like components in LLDPE resin exerted the adhesive effect at lower heating temperature, HDPE-like components exerted the strong adhesive effect at higher heating temperature.     

Radiation chemistry of linear low-density polyethylene. II. Kinetics of alkyl and allyl free-radical decay reactions

Quenched and annealed samples of linear low-density polyethylene (LLDPE) were γ irradiated in vacuo at 77 K; the kinetics of the alkyl free-radical decay reactions were studied at room temperature, and of the allyl free-radical reactions at 60, 70, and 80°C. The ESR signals saturate at a slightly higher microwave power in the LLDPE than in high-density polyethylene (HDPE), and the alkyl radicals start decaying at a lower temperature in the LLDPE than in the HDPE. As in the HDPE the decay of the alkyl free radicals at room temperature in the LLDPE follows the kinetic equation for two simultaneous first-order reactions with the fraction of the faster-decaying component being slightly greater in the quenched than in the annealed samples. In the case of the allyl free radicals the decay at 60°C follows the equation based on one fraction of the radicals decaying according to second-order kinetics in the presence of other nondecaying radicals. At higher temperatures the data are best understood in terms of a second-order rate equation with a continuously variable time-dependent rate constant as suggested by Hamill and Funabashi.     

Morphology,structure, and properties of in situ compatibilized linear low‐density polyethylene/polystyrene and linear low‐density polyethylene/high‐impact polystyrene blends

Blends of linear low‐density polyethylene (LLDPE) with polystyrene (PS) and blends of LLDPE with high‐impact polystyrene (HIPS) were prepared through a reactive extrusion method. For increased compatibility of the two blending components, a Lewis acid catalyst, aluminum chloride (AlCl₃), was adopted to initiate the Friedel–Crafts alkylation reaction between the blending components. Spectra data from Raman spectra of the LLDPE/PS/AlCl₃ blends extracted with tetrahydrofuran verified that LLDPE segments were grafted to the para position of the benzene rings of PS, and this confirmed the graft structure of the Friedel–Crafts reaction between the polyolefin and PS. Because the in situ generated LLDPE‐g‐PS and LLDPE‐g‐HIPS copolymers acted as compatibilizers in the relative blending systems, the mechanical properties of the LLDPE/PS and LLDPE/HIPS blending systems were greatly improved. For example, after compatibilization, the Izod impact strength of an LLDPE/PS blend (80/20 w/w) was increased from 88.5 to 401.6 J/m, and its elongation at break increased from 370 to 790%. For an LLDPE/HIPS (60/40 w/w) blend, its Charpy impact strength was increased from 284.2 to 495.8 kJ/m². Scanning electron microscopy micrographs showed that the size of the domains decreased from 4–5 to less than 1 μm, depending on the content of added AlCl₃. The crystallization behavior of the LLDPE/PS blend was investigated with differential scanning calorimetry. Fractionated crystallization phenomena were noticed because of the reduction in the size of the LLDPE droplets. The melt‐flow rate of the blending system depended on the competition of the grafting reaction of LLDPE with PS and the degradation of the blending components. The degradation of PS only happened during the alkylation reaction between LLDPE and PS. Gel permeation chromatography showed that the alkylation reaction increased the molecular weight of the blend polymer. The low molecular weight part disappeared with reactive blending. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1837–1849, 2003     

Characterization and properties of polyethylene blends I. Linear low-density polyethylene with high-density polyethylene

A blend system of linear low-density polyethylene (LLDPE) (ethylene butene-1 copolymer) with high-density (linear) polyethylene (HDPE) is investigated by differential scanning calorimetry (DSC), wide-angle x-ray diffraction (WAXD), small-angle x-ray scattering (SAXS), Raman longitudinal-acoustic-mode spectroscopy (LAM), and light scattering (LS). For slowly cooled or quenched samples, one single endotherm is evident in the DSC curve which depends on the composition. No separate peaks are observed in the WAXD, SAXS, Raman-LAM, and LS studies on the LLDPE/HDPE blends. This observation along with the fact that no peak broadening is observed suggests that these peaks are associated with the presence of a single component. In no case did we see double peaks or a broadened peak that might be associated with two closely spaced unresolved peaks. This suggests that segregation has not taken place at the structural levels of crystalline, lamellar, and spherulitic textures. A single-step drop in the scattered intensity (I_Hv) as a function of temperature is seen in the LS studies. It is therefore concluded that cocrystallization between the LLDPE and HDPE components occurs. The mechanical and optical α, β, and γ relaxations of these blends are explored by dynamic birefringence. The 50/50 blend displays the intermediate relaxation behavior between those of the components in all α, β, and γ regions. This observation is reminiscent of the characteristic of the typical miscible blends.     

Preparation and physical properties of novel nonionic surfactants and their grafting copolymers with linear low density polyethylene (LLDPE)

Three nonionic surfactants, S1, S2, and S3 and their acrylates, AS1, AS2, and AS3, were synthesized with poly(ethylene oxide) and diols such as glycol, 1,6‐hexanediol, and 1,10‐decanediol as the main starting materials. Their chemical structures were characterized by means of Fourier transform infrared (FTIR) spectroscopy and ¹H NMR. The surface activity and surface tension (γ) of S1, S2, and S3 were evaluated by a drop weight method. The surface tension was found to decrease with the length of the lipophilic spacer in the molecular chains (γ_S1 < γ_S2 < γ_S3). AS1, AS2, and AS3 were adopted as functionalizing monomers and grafted onto linear low density polyethylene (LLDPE) with a melt reactive extrusion procedure. The graft degrees of LLDPE were determined by FTIR. Three grafted LLDPE samples with grafting degrees of 1.16% (AS1), 0.82% (AS2), and 0.71% (AS3) were prepared. Thermal and rheological properties of grafted LLDPE samples were studied with differential scanning calorimetry and a rotational rheometer. Crystallization rates of grafted LLDPE were faster than that of plain LLDPE at a given crystallization temperature because graft chains could act as nucleating agents. The isothermal crystallization behavior of grafted LLDPE was in accordance with the Avrami model only in the first stage, and deviated from the model with an increase in the crystallization time. Shear thinning at high shear rates and shear thickening at low shear rates were observed for the grafted LLDPE. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 314–322, 2005     

新型聚乙烯接枝共聚物的制备与表征

以聚氧乙烯和全氟辛基聚氧乙烯醚(FPEOE)为起始原料, 合成了一系列的特种氟表面活性剂及其丙烯酸酯, 用FTIR和1H NMR对其结构进行了表征, 用最大气泡法测定了其表面张力. 以其作为接枝单体, 利用反应挤出接枝的方法制备了系列功能化聚乙烯, 用FTIR确定了接枝共聚物的结构和接枝率; 用DSC、接触角测量仪和XPS对接枝共聚物的热性能、结晶行为和表面性能进行了测试分析. 结果表明, 随着聚氧乙烯分子量的增加, 氟表面活性剂的表面活性降低; 聚乙烯接枝共聚物的结晶温度高于线形低密度聚乙烯, 且具有较好的亲水性.     

Effect of reaction conditions on the grafting of 2-(dimethylamino)ethyl methacrylate onto hydrocarbon substrates

The grafting of 2-(dimethylamino)ethyl methacrylate (DMAEMA) onto two model hydrocarbons, squalane and n-eicosane, and to linear low density polyethylene (LLDPE) has been investigated. The results of the study indicate that a high reaction temperature, 160°C, and a low concentration of monomer, less than 0.3 M, are optimum conditions for the grafting reaction. Reaction products, which consisted of grafted hydrocarbons and poly(DMAEMA), were separated by solvent extraction and vacuum distillation; samples were then analyzed by NMR and FTIR spectroscopy and size exclusion chromatography. ¹H-NMR spectroscopy indicates that grafted squalane contained approximately 6 DMAEMA units per squalane residue. ¹H- and ¹³C-NMR and molecular weight studies strongly suggest that the grafts onto the model hydrocarbons consist of single DMAEMA units. Results of the melt grafting of DMAEMA onto LLDPE show that the grafting efficiency and degree of grafting are substantially lower than were expected from the model system. © 1994 John Wiley & Sons, Inc.     

Graft Copolymerization of 2‐Acrylamido‐2‐methyl Propane Sulfonic Acid on Dimethyl Sulfoxide Pretreated Poly(Ethylene Terephthalate) Films Using Cerium Ammonium Nitrate as Initiator

Abstract

In this study, graft polymerization of 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS) on poly(ethylene terephthalate) (PET) films using cerium ammonium nitrate (CeAN) as an initiator was investigated. Before the polymerization reaction was carried out, films were swelled in dimethyl sulfoxide (DMSO) at 140°C for 1 h. The effect of polymerization temperature, time, initiator, and monomer concentrations on the graft yield were investigated. It was observed that the graft yield was initially increased with increasing temperature, monomer, and initiator concentrations; and then decreased. Graft yield was found to increase with increasing polymerization time up to 5 h, then remain constant. The effects of monomer and initiator inclusions on the grafting yield were also examined. Optimum conditions for grafting were found to be [AMPS] = 1.0 M, [Ce⁴⁺] = 1.5 × 10^?2 M, T = 85°C and t = 5 h. The rate of grafting was found to be proportional to the 0.1 and 0.4 powers of monomer and initiator concentrations, respectively. The overall activation energy for the grafting was calculated to be 11.4 kcal mol^?1. The effect of grafting on PET film properties such as intrinsic viscosity and water absorption capacity were determined. The grafted PET films were characterized with FTIR spectroscopy and scanning electron microscopy (SEM).     

Radiation-induced grafting of hexafluoroacetone to polyethylene

Although hexafluoroacetone is not polymerized by ionizing radiation, it is shown that γ-irradiation of hexafluoroacetone dissolved in polyethylene films produces a graft with a G value of 500 and, therefore, a kinetic chain length of 200. The effects of dose rate (0.021–3.55 Mrad/hr), temperature (21–53°C), and pressure (1.5–6.2 atm) on the graft rates have been measured. Also the effect of temperature (21–53°C) on the postirradiation grafting reaction and on the physical properties of the grafted films have been investigated. Together with solubility, diffusivity, infrared, and EPR data, the results lead to the following mechanism: The first step represents production of secondary alkyl radicals in the polyethylene by irradiation of the polymer–monomer system. The second step involves the linkage of the monomer to the radical site to form the alkoxy radical. Since it cannot add to another monomer unit, this radical abstracts a hydrogen atom from an adjacent polyethylene chain in the third step. Radical R· can then continue the kinetic chain. Radical combination and radical–impurity reactions terminate the chain. The graft may be unique in that it is the only one we have found in which a pendant group containing only one monomer unit is attached by a chain reaction. At dose rates up to 0.215 Mrad/hr, the grafting was linear with time and proportional to the 0.73 power of the dose rate at 21°C and to the 0.81 power at 53°C. The reaction is insensitive to increases in dose rate above 0.215 Mrad/hr where diffusivity measurements show the reaction to be diffusion-controlled. The rate of reaction increased 10% when the temperature was increased from 21 to 53°C. While there was significant postirradiation grafting reaction at 21°C, there was none at 53°C. The results do not fit the equations of reaction-controlled steady-state graft-polymerization kinetics. The deviations arise from an observed increase in monomer solubility in the film with increasing graft combined with low diffusivity of the monomer in polyethylene, and the presence of a radical-scavenging impurity which terminates the kinetic chain with the appearance of a relatively stable radical. EPR data suggests that the impurity is a trace of oxygen which may be produced radiolytically.     

Characteristics of solid-state extruded polyethylene

This paper describes the properties of solid-state extruded polyethylene as a function of two primary processing variables, extrusion temperature, and area reduction. The polymer was extruded in sheet form, giving a material having an orthotropic mode of orientation. Property data are presented for melting temperature and heat of fusion; sonic modulus, yield stress, and elongation at fracture; small-angle x-ray scattering; optical absorption coefficient; and morphology for material etched by ion bombardment at liquid nitrogen temperature. Combining the present results with data previously reported in the literature, it is found that over the temperature range of about 90–120°C, where polyethylene can be successfully extruded to large area reductions, many properties of the extrudates show a surprisingly small dependence on extrusion temperature. A notable exception to this behavior is the elastic modulus, which increases significantly with increasing extrusion temperatures. In contrast to extrusion temperature, area reduction is found to have a major effect on nearly all properties of solid-state extruded polyethylene. In most cases, the form of this dependence is such that the properties change rapidly at small area reductions and much more slowly at large reductions.     

Amperometric glucose biosensor based on platinum nanoparticle encapsulated with a clay

Electrically conductive hollow nanospheres with an average diameter between 100 and 200 nm were prepared via a one-step polymerization of aniline in the presence of lignosulfonate (LS) by using ammonium persulfate (APS) as the oxidant. The LS concentration and molar ratio between APS and aniline, the temperature and time for polymerization were adjusted to optimize morphology, structure and electrochemical properties. Uniform hollow nanospheres are best obtained at a concentration of 18 wt% of LS, at a polymerization temperature at 25 °C, at an APS/aniline molar ratio of 1:1, and at a polymerization time of 1 to 12 h. This kind of preparation of nanospheres represents a simple and general route to polymer hollow nanospheres of controllable size, high stability, and optimizable electroconductivity.     

Thermally resolved synchrotron FT-IR microscopy of structural changes in bloodmeal-based thermoplastics

Synchrotron FT-IR micro-spectroscopy was used to determine thermally induced structural changes in thermoplastic protein produced from bloodmeal after mixing with sodium sulphite, sodium dodecyl sulphate, urea, tri-ethylene glycol and water. Changes in protein secondary structure at elevated temperature were assessed using second derivative peak height ratios in the amide III region (1,200–1,330 cm^?1) and compared with DSC and DMA results over the same temperature range. The results show an increase in ordered β-sheet structures with temperature at the expense of random coils, and that these β-sheets do not melt in the temperature range up to extrusion temperature of 120 °C. The implication of this is that during melt processing, β-sheet clusters may remain intact, similar to dispersed particulate fillers.     

Polyethylene glycol grafted cotton as phase change polymer

Thermal storage cotton possessing solid–solid phase change properties was prepared by direct grafting of polyethylene glycol (PEG) on cotton fiber/cloth. Attempt has been made to characterize intermediates so that desired grafting could be obtained. The grafting was done by using urethane linkage and the grafted cotton was found to undergo solid–solid phase transition. The modified cotton was characterized by using Fourier transform infrared spectroscopy (FT-IR), ¹³C CPMAS, polarizing optical microscopy, differential scanning calorimetry (DSC) and thermogravimetry respectively. The DSC study revealed quite good storage effect of grafted cotton and the enthalpy of melting was found to be 55–59 J/g with a peak appearing at around 60 °C. During cooling scan, the crystallization peak appeared at around 38 °C. Further, thermogravimetric analysis confirmed good thermal stability up to 300 °C. Appreciable improvement of mechanical properties of cotton has been observed after grafting. The polarizing optical micrograph clearly showed change of morphology after grafting, i.e., the grafted PEG adhering to fiber surface.     

Melt elongation flow behaviour of LDPE/LLDPE blends

The extensional rheological properties of low density polyethylene (LDPE)/linear low density polyethylene (LLDPE) blend melts were measured using a melt spinning technique under temperatures ranging from 160 to 200 °C and die extrusion velocities varying from 9 to 36 mm/s. The results showed that the melt elongation stress decreased with a rise of temperature while it increased with increasing extensional strain rate and the LDPE weight fraction. The dependence of the melt elongation viscosity on temperature roughly obeyed the Arrhenius equation, it increased with increasing extensional strain rate and the LDPE weight fraction when the extensional strain rate was lower than 0.5 s⁻¹, and it reached a maximum when the extensional strain rate was about 0.5 s⁻¹, which can be attributed to the stress hardening effect.     

Desorption behavior of a surfactant in a linear low‐density polyethylene blend at elevated temperatures

The desorption behavior of a surfactant in a linear low‐density polyethylene (LLDPE) blend at elevated temperatures of 50, 70, and 80 °C was studied with Fourier transform infrared spectroscopy. The composition of the LLDPE blend was 70:30 LLDPE/low‐density polyethylene. Three different specimens (II, III, and IV) were prepared with various compositions of a small molecular penetrant, sorbitan palmitate (SPAN‐40), and a migration controller, poly(ethylene acrylic acid) (EAA), in the LLDPE blend. The calculated diffusion coefficient (D) of SPAN‐40 in specimens II, III, and IV, between 50 and 80 °C, varied from 1.74 × 10^?11 to 6.79 × 10^?11 cm²/s, from 1.10 × 10^?11 to 5.75 × 10^?11 cm²/s, and from 0.58 × 10^?11 to 4.75 × 10^?11 cm²/s, respectively. In addition, the calculated activation energies (E_D) of specimens II, III, and IV, from the plotting of ln D versus 1/T between 50 and 80 °C, were 42.9, 52.7, and 65.6 kJ/mol, respectively. These values were different from those obtained between 25 and 50 °C and were believed to have been influenced by the interference of Tinuvin (a UV stabilizer) at elevated temperatures higher than 50 °C. Although the desorption rate of SPAN‐40 increased with the temperature and decreased with the EAA content, the observed spectral behavior did not depend on the temperature and time. For all specimens stored over 50 °C, the peak at 1739 cm^?1 decreased in a few days and subsequently increased with a peak shift toward 1730 cm^?1. This arose from the carbonyl stretching vibration of Tinuvin, possibly because of oxidation or degradation at elevated temperatures. In addition, the incorporation of EAA into the LLDPE blend suppressed the desorption rate of SPAN‐40 and retarded the appearance of the 1730 cm^?1 peak. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1114–1126, 2004     

Aging of piezoelectricity in poly(vinylidene fluoride)

This report describes isothermal aging of piezoelectricity in poly(vinylidene fluoride) (PVDF) based on long-term heat treatments between 40 and 160°C. The results demonstrate that no piezoelectric decay occurs below about 60°C, that between 60 and 160°C the aging behavior follows logarithmic kinetics, and that aging is linearly dependent on temperature. Both uniaxial and biaxial PVDF show similar trends, but piezoelectric decay is more rapid for uniaxial film. Decay of permanent poling-induced polarization is identified as the likeliest cause of piezoelectric aging, and piezoelectric decay is found to be associated with long-range annealing effects which also produce macroscopic shrinkage of the PVDF film.     

Different methods for β-cyclodextrin/triclosan complexation as antibacterial treatment of cellulose substrates

Two different production ways of antibacterial cotton fabrics by means of triclosan inclusion into a β-cyclodextrin cavity have been compared. On the one hand, triclosan has been dissolved into an aqueous solution of a β-cyclodextrin derivative with the aim of including the antibacterial agent into the cavity before grafting the β-cyclodextrin on a cotton fabric. On the other hand, the same β-cyclodextrin derivative has been grafted onto cotton and, subsequently, the fabric has been immersed into a triclosan water–ethanol solution to allow the inclusion complex formation. The antibacterial properties have been evaluated according to AATCC Test Method 100–1993 before and after two washing cycles at 60 °C. It has been shown that the durability of the antibacterial finishing depends on the production method, obtaining a more durable antibacterial action in case of prior triclosan inclusion followed by grafting. This suggests that the immobilization onto the fiber has affected the cyclodextrin cavity accessibility.