Synthesis and characterization of luminescent polyethers with 2,5‐distyrylthiophene and aromatic oxadiazole chromophores

Two new luminescent copolyethers ( P1 and P2 ) with isolated 2,5‐distyrylthiophene‐emitting segments and electron‐transporting 2,5‐diphenyl‐1,3,4‐oxadiazole chromophores were successfully synthesized by the Horner–Wadworth–Emmons reaction. The solubility, optical, and electrochemical properties of the polymers were investigated and correlated with nonlinear thiophene and 1,3,4‐oxadiazole groups. P2 with pendant 1,3,4‐oxadiazole was soluble in common organic solvents such as chloroform, tetrahydrofuran, and C₂H₂Cl₄. Thermogravimetric analysis and differential scanning calorimetry showed that the copolyethers were thermally stable below 345 °C, with glass‐transition temperatures higher than 110 °C. They were yellow‐greenish emitting materials with a band gap of 2.57–2.58 eV estimated from the onset absorption. Incorporating the thiophene moiety narrowed the band gaps of the copolyethers. The photophysical and electronic properties of the polymer and the preliminary electroluminescent device made from the polymer demonstrate that the polymer may be a potential candidate material for the fabrication of polymeric light‐emitting devices. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2927–2936, 2002     

New Semiconducting Poly(arylene sulfide)s: Synthesis,Characterization, and Optical Properties

New semiconducting soluble poly(arylene sulfide)s were synthesized by Wittig polycondensation. The arylene moieties consist of distyrylbiphenyl (P1) and distyrylbithiophene (P2) π-conjugated systems. The polymers are fully amorphous and show good thermal stability. The absorption and photoluminescence properties of the polymers were investigated. P1 film has an optical gap of 2.95 eV and exhibits green-blue fluorescence. P2 shows a longer effective conjugation length with a gap of 2.42 eV and emits in the orange region. The HOMO/LUMO energy levels were estimated by cyclic voltammetry measurements. Single-layer diodes were fabricated and show relatively low turn-on voltages.     

Synthesis,characterization, and electroluminescence of fluorene and carbazole‐based blue light‐emitting polymers with different noncoplanar molecular architectures

In order to investigate the explicit optoelectronic variations of the photoluminescent polymer with sterically hindered side chains, three novel alternate polymers (P0, P1, and P2) based on fluorene and carbazole moieties were successfully synthesized through Suzuki coupling reaction. The molecular structures of the polymers were fully characterized by ¹H‐NMR, ¹³C‐NMR, elemental analysis, and gel permeation chromatograph, respectively. The photophysical properties, thermal stability, and energy band gaps of polymers P0, P1, and P2 were further examined through UV–vis absorption, photoluminescent spectra, differential scanning calorimetry, thermogravimetric analysis, and cyclic voltammetry. The experimental results indicated that the polymers took on wide band gaps of about 3.50 eV with deep blue emission in thin solid films. These polymers were found to show a high thermal stability with decomposition temperatures at 5% weight loss of the compounds in the range of 353–416 °C. Blue light‐emitting electroluminescent devices of the most branched polymer P2 with highest light‐emitting efficiency as emitting layers were characterized, which showed obviously improved spectral stabilities with respect to the parent polyfluorene materials. In conclusion, we have established an effective method to improve the spectral stabilities of polyfluorene material by synthesizing the zigzag‐shaped copolymer of fluorene and carbazole with sterically hindered pendant moieties of different molecular sizes. Copyright © 2014 John Wiley & Sons, Ltd.     

Blue-luminescent poly(p-phenylenevinylene) derivatives: Synthesis and effect of side-group size on the optical properties

New conjugated polymers based on separated PPV-type chromophores and incorporating different types of solubilizing side-groups (ethoxy: P1, hexyloxy: P2, dodecyloxy: P3 and benzyloxy: P4) were synthesized via Wittig polycondensation, using a series of bisphenol A-derived di(triphenylphosphonium) salts as starting monomers. The polymers are soluble in common organic solvents and their structures were confirmed by ¹H NMR, ¹³C NMR and FTIR spectroscopies. The optical properties of these materials were investigated by UV–vis absorption and fluorescence spectroscopies. In dilute solution, quasi-identical fluorescence spectra were obtained and all the polymers showed a blue emission (420, 445 nm) and a narrow spectrum. In thin solid films, the polymers show side-group-dependent optical behavior and, whereas the emission remains blue in the case of P2, P3 and P4, a green fluorescence was observed for the ethoxylated polymer P1. From cyclic voltammetry analysis, the electrochemical band gaps were estimated to be 2.99, 3.07, 3.15 and 3.06 eV for P1, P2, P3 and P4, respectively. Single-layer diode devices of the [indium tin oxide/polymer/aluminum] configuration have been fabricated and show relatively low turn-on voltages between 2.6 and 4.9 V.     

Wide bandgap conjugated polymers based on bithiophene and benzotriazole for bulk heterojunction solar cells: Thiophene versus thieno[3,2-b]thiophene as π-conjugated spacers

Two wide bandgap (WBG) conjugated polymers, P2T-DTTTAZ and P2T-DTTAZ, with donor-π-acceptor (D-π-A) structures was designed and synthesized, utilizing thieno[3,2-b]thiophene (TT) and/or thiophene (T) units as π-bridge in conjugated polymer backbone. And, the wider optical band gap (E_g) of approximately 1.98 eV for P2T-DTTTAZ and 2.09 eV for P2T-DTTAZ were observed. Obviously, replacing T unit with larger conjugated plane TT unit as π-bridges, P2T-DTTTAZ resulted in the red shifted absorption and the reduced band gap, compared with these of P2T-DTTAZ. The polymer solar cells (PSCs) with an inverted device structure based on P2T-DTTTAZ or P2T-DTTAZ as donor and [6,6] phenyl-C₆₁ butyric acid methyl ester (PC₆₁BM) as acceptor were assembled and the photovoltaic properties were also investigated. The power conversion efficiencies (PCEs) of 1.57% for P2T-DTTTAZ and 1.25% for P2T-DTTAZ were obtained.     

Synthesis,Structure, and Physical Properties of 5,7,14,16‐Tetraphenyl‐8:9,12:13‐bisbenzo‐hexatwistacene

A novel compound, 5,7,14,16‐tetraphenyl‐8:9,12:13‐bisbenzo‐hexatwistacene ( TBH ), has been successfully synthesized through a retro‐Diels–Alder reaction. Single‐crystal structure analysis indicated that TBH has a twisted configuration with a torsion angle of 27.34°. The HOMO–LUMO gap of TBH calculated from the difference between the half‐wave redox potentials (E_1/2^ox=+0.40 eV and E_1/2^red=?1.78 eV) is 2.18 eV, which is in good agreement with the band gap (2.19 eV) derived from the UV/Vis absorption data. In addition, organic light‐emitting devices using TBH as emitter have been fabricated. The results revealed that TBH is a promising red light‐emitting candidate for applications in organic light‐emitting diodes.     

Synthesis of the (X-DADAD)n-type conjugated polymers with 2,1,3-benzoxadiazole acceptor blocks and their application in organic solar cells

Two polymers with benzoxadiazole acceptor units were synthesized and investigated as electron donor materials in organic solar cells. Variation of the alkyl substituents was shown to significantly affect the optoelectronic properties of the polymers. In particular, the polymer HOMO energy level was lowered by 0.1 eV, while maintaining the same band gap, by replacement of the 2-ethylhexyl side-chains with the 2-hexyldecyl group. This modification also resulted in a higher open circuit voltage of the solar cells.     

Perylene diimide copolymers with dithienothiophene and dithienopyrrole: Use in n‐channel and ambipolar field‐effect transistors

Solution‐processable polymers consisting of perylene diimide (PDI) acceptor moieties alternating with dithienothiophene (DTT), N‐dodecyl‐dithienopyrrole (DTP), or oligomers of these donor groups have been synthesized. We have, in addition to varying the donor, varied the N,N′ substituents of the PDIs. The thermal, optical, electrochemical, and charge‐transport properties of the polymers have been investigated. The polymers show broad absorption extending from 300 to 1000 nm with optical band gaps as low as 1.2 eV; the band gap decreases with increasing the conjugation length of donor block, or by replacement of DTT by DTP. The electron affinities of the polymers, estimated from electrochemical data, range from ?3.87 to ?4.01 eV and are slightly affected by the specific choice of donor moiety, while the estimated ionization potentials (?5.31 to ?5.92 eV) are more sensitive to the choice of donor. Bottom‐gate top‐contact organic field‐effect transistors based on the polymers generally exhibit n‐channel behavior with electron mobilities as high as 1.7 × 10^–2 cm²/V/s and on/off ratios as high as 10⁶; one PDI‐DTP polymer is an ambipolar transport material with electron mobility of 4 × 10^–4 cm²/V/s and hole mobility of 4 × 10^–5 cm²/V/s in air. There is considerable variation in the charge transport properties of the polymers with the chemical structures. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Soluble polynorbornenes with pendant carbazole derivatives as host materials for highly efficient blue phosphorescent organic light‐emitting diodes

We report novel host polymers for a high‐efficiency polymer‐based solution‐processed phosphorescent organic light‐emitting diode with typical blue‐emitting dopant bis(4,6‐difluorophenylpyridinato‐N,C²)iridium(III) picolinate (FIrpic). The host polymers, soluble polynorbornenes with pendant carbazole derivatives, N‐phenyl‐9H‐carbazole ( P1 ), N‐biphenyl‐9H‐carbazole ( P2 ), and 9,9′‐(1,3‐phenylene)bis‐9H‐carbazole (mCP) ( P3 ) are efficiently synthesized by vinyl addition polymerization of norbornene monomers using Pd(II) catalyst in combination with 1‐octene chain transfer agent. The polymers exhibit high thermal stability with high decomposition (T_d5 > 410 °C) and glass transition temperatures (T_g ≈ 268 °C). The HOMO (ca. ?5.5 to ?5.7 eV) and LUMO (ca. ?2.0 to ?2.1 eV) levels with the high triplet energy of about 2.7–3.0 eV suggest that the polymers are suitable for a host material for blue emitters. Among the solution‐processed devices that were fabricated based on the emissive layers containing the P1 ? P3 host doped with various concentrations of FIrpic (7–13 wt %), the best device with P3 host exhibits power efficiency of 3.0 lm W^?1 and external quantum efficiency of 4.0% at a luminance of 1000 cd m^?2 that is outstanding among the polymeric rivals. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Syntheses,electrochemical and spectroelectrochemical characterization of benzothiadiazole and benzoselenadiazole based random copolymers

Three novel donor-acceptor-donor type random copolymers based on benzothiadiazole (BTh) and benzoselenadiazole (BSe) were synthesized via Pd (0) catalyzed Suzuki polycondensation reaction. The two acceptor units were coupled with electron rich moieties which are carbazole (CZ), fluorene (FL) and silafluorene (SiFL). Monomers were characterized using ¹H and ¹³C-NMR spectroscopy. The number and weight average molecular weights of the polymers were calculated using gel permeation chromatography (GPC). All three polymers were electrochemically and spectroelectrochemically characterized. PBThBSeCZ, PBThBSeFL and PBThBSeSiFL showed only p-dopable character and their doping/dedoping potentials were determined as 1.4 V/1.2 V, 1.53 V/1.27 V and 1.8 V/1.3 V, respectively. Corresponding HOMO energy levels were calculated as ?5.85 eV, ?6.05 eV and ?6.15 eV whereas LUMO energy levels were found to be ?3.67 eV, ?3.84 eV and ?3.77 eV, respectively. PBThBSeCZ had lower HOMO level and band gap than PBThBSeFL and PBThBSeSiFL due to its increased electron donating capability of nitrogen atom in carbazole unit.     

Synthesis and photovoltaic properties of two‐dimensional D‐A copolymers with conjugated side chains

Four novel two‐dimensional (2D) donor–acceptor (D‐A) type copolymers with different conjugated side chains, P1 , P2 , P3 , and P4 (see Fig. 1 ), are designed and synthesized for the application as donor materials in polymer solar cells (PSCs). To the best of our knowledge, there were few reports to systematically study such 2D polymers with D‐A type main chains in this area. The optical energy band gaps are about 2.0 eV for P1 – P3 and 1.67 eV for P4 . PSC devices using P1 – P4 as donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as acceptor in a weight ratio of 1:3 were fabricated and characterized to investigate the photovoltaic properties of the polymers. Under AM 1.5 G, 100 mA/cm² illumination, a high open‐circuit voltage (V_oc) of 0.9 V was recorded for P3 ‐based device due to its low HOMO level, and moderate fill factor was obtained with the best value of 58.6% for P4 ‐based device, which may mainly be the result of the high hole mobility of the polymers (up to 1.82 × 10^?3 cm²/V s). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Low bandgap π‐conjugated copolymers based on fused thiophenes and benzothiadiazole: Synthesis and structure‐property relationship study

A series of low bandgap conjugated polymers consisting of benzothiadiazole alternating with dithienothiophene (DTT) or dithienopyrrole (DTP) unit with or without 3‐alkylthiophene bridge have been synthesized. Effect of the fused rings and 3‐alkylthiophene bridge on the thermal, optical, electrochemical, charge transport, and photovoltaic properties of these polymers have been investigated. These polymers show broad absorption extending from 300 to 1000 nm with optical bandgaps as low as 1.2 eV; the details of which can be varied either by incorporating 3‐alkylthiophene bridge or by replacing DTT with DTP. The LUMO levels (?2.9 to ?3.3 eV) are essentially unaffected by the specific choice of donor moiety, whereas the HOMO levels (?4.6 to ?5.6 eV) are more sensitive to the choice of donor. The DTT and DTP polymers with 3‐alkylthiophene bridge were found to exhibit hole mobilities of 8 × 10^?5 and 3 × 10^?2 cm² V^?1 s^?1, respectively, in top‐contact organic field‐effect transistors. Power conversion efficiencies in the range 0.17–0.43% were obtained under simulated AM 1.5, 100 mW cm^?2 irradiation for polymer solar cells using the DTT and DTP‐based polymers with 3‐alkylthiophene bridge as donor and fullerene derivatives as acceptor. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5498–5508, 2009     

Diketopyrrolopyrrole‐based acceptor–acceptor conjugated polymers: The importance of comonomer on their charge transportation nature

Besides the donor–acceptor (D–A) type, acceptor–acceptor (A–A) polymers are another class of important alternative conjugated copolymers, but have been less studied in the past. In this study, two kinds of A–A polymers, P1 and P2 , have been designed and synthesized based on diketopyrrolopyrrole in combination with the second electron‐deficient unit, perylenediimide or thieno[3,4‐c]pyrrole‐4,6‐dione. UV–vis absorption spectroscopy revealed that these two kinds of polymers have a band gap of 1.28–1.33 eV. Their highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels are around ?5.6 and ?4.0 eV for P1 polymers, whereas ?5.4 and ?3.7 eV for P2 polymers, respectively. Density functional theory study disclosed that P1 backbone is in a vastly twisting state, whereas that of P2 is completely planar. Furthermore, organic field‐effect transistor devices were fabricated using these two kinds of polymers as the active material. Of interest, the devices based on P1 polymers displayed n‐channel behaviors with an electron mobility in the order of 10^?4 cm² V^?1 s^?1. In contrast, the P2 ‐based devices exhibited only p‐channel charge transportation characteristics with a hole mobility in the order of 10^?3 cm² V^?1 s^?1. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2356–2366     

Zn(II)-containing metallo-supramolecular polymers: synthesis,photophysical and electrochemical properties

Abstract

Two novel building blocks M1, M2 with different electronic structures, were synthesized based on 2,2′:6′,2″-terpyridine modified with cyano-p-phenylenevinylene (CN-PV) and carbazole moieties through Knoevenagel condensation and Suzuki coupling, respectively. Directed by transition metal ion Zn²⁺, the metallo-homopolymers P1, P2 and metallo-copolymer P3 were obtained via self-assembly polymerization. The structures of the monomers and metallo-supramolecular polymers were fully characterized by MS, ¹H-NMR and ¹³C-NMR. Meanwhile, the UV–vis absorption, photoluminescence (PL) and electrochemical properties of these compounds were systematically investigated. With respect to that of the monomers, both the UV–vis absorption and PL spectra of the polymers are significantly red-shifted. The resulting metallo-supramolecular polymers show similar double absorption peaks (342, 418?nm for P1, 339, 410?nm for P2, and 332, 412?nm for P3), which is caused by the π–π* transition and intramolecular charge transfer (ICT). Further, all the polymers display red-orange emission in toluene and narrow electrochemical energy gaps of 1.46, 1.65 and 1.48?eV for P1, P2, and P3, respectively.     

Synthesis and properties of nitrogen‐linked poly(2,7‐carbazole)s as hole‐transport material for organic light emitting diodes

A novel class of carbazole polymers, nitrogen‐linked poly(2,7‐carbazole)s, was synthesized by polycondensation between two bifunctional monomers using the palladium‐catalyzed amination reaction. The polymers were characterized by ¹H NMR, Infrared, Gel permeation chromatography, and MALDI‐TOF MS and it was revealed that the combination of the monomer structures is important for producing high molecular weight polymers. Thermal analysis indicated a good thermal stability with high glass transition temperatures, e.g., 138 °C for the higher molecular weight polymer P2 . To pursue the application possibilities of these polymers, their optical properties and energy levels were investigated by UV‐Vis absorption and fluorescence spectra as well as their electrochemical characteristics. Although the blue light emission was indeed observed for all polymers in solution, the quantum yields were very low and the solid films were not fluorescent. On the other hand, the HOMO levels of the polymers estimated from the onset potentials for the first oxidation in the solid thin films were relatively high in the range of ?5.12 to ?5.20 eV. Therefore, light emitting diodes employing these polymers as a hole‐transport layer and iridium(III) complex as a triplet emitter were fabricated. The device of the nitrogen‐linked poly(2,7‐carbazole) P3 with p,p′‐biphenyl spacer, which has a higher HOMO level and a higher molecular weight, showed a much better performance than the device of P2 with m‐phenylene spacer. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3880–3891, 2009     

ZnO nanoparticles and poly(acrylic) acid-based polymer gel electrolyte for photo electrochemical cell

This work presents a photo electrochemical cell based on zinc oxide (ZnO) nanoparticles and poly(acrylic) acid (PAA) doped with sodium iodide (NaI) and iodine (I₂) polymer gel electrolyte. The ZnO powders were synthesized by sol–gel storage and sol–gel centrifugation. The ZnO powder synthesized via sol–gel centrifugation showed the optimal structural properties, with largest crystallite sizes of 58 nm, average particles size between 20 and 80 nm and indirect band gap energy of 3.20 eV. The highest conductivity [(8.0 ± 0.1) × 10^?2 S cm^?1] was obtained for PAA + 0.8 M NaI + 0.02 M I₂. This sample achieved the lowest activation energy (0.029 eV) and electrochemical stability at 1.6 V. The ZnO powder synthesized via sol–gel centrifugation and PAA + 0.8 M NaI + 0.02 M I₂ was fabricated as a Cu–ZnO/PAA + 0.8 M NaI + 0.02 M I₂/C-ITO photo electrochemical cell.     

Crystal structure,optical properties,and theory study of a 1-D bromoplumbate stabilized by in situ generated N-alkylated DABCO cation

We report the exploration of the stabilization effect of the in situ generated N-alkylated DABCO (DABCO = 1,4-diazabicyclo[2.2.2]octane) cation in the family of bromoplumbates and a 1-D bromoplumbate, (Et₂DABCO)_2n(Pb₃Br₁₀)_n (1), has been prepared by solvothermal conditions. Optical diffuse reflectance determination shows the band gap of 1 is 3.69 eV, which manifests that 1 is a wide band gap semiconductor. Compared with the band gap of bulk PbBr₂ (3.84 eV), 1 exhibits 0.15 eV red shift of absorption edge. While for the reported iodo analogs of this compound, (MPDA)_2n(Pb₃I₁₀)_n and (Et₂DABCO)_2n(Pb₃I₁₀)_n, they exhibit 0.53 and 0.47 eV blue shift of the energy gaps compared with the measured value of 2.30 eV for bulk PbI₂, respectively. The photoluminescent study of 1 shows that it exhibits a broad emission band centered at 697 nm upon photoexcitation by 345 nm (amount to 3.59 eV). The calculated density of states manifests the theoretical value of the band gap of 1 is 3.422 eV and the origination of photoluminescence can be ascribed to the transition of bonding electrons of Br^– anion to the empty orbits of Pb(II) ion.     

Design and synthesis of pyromellitic diimide‐based donor–acceptor conjugated polymers for photovoltaic application

Three of conjugated polymers based on pyromellitic diimide (PMDI) as the acceptor unit and thienothiophene (TT) as the donor unit were successfully synthesized by Stille coupling. The effect of the side chain length and thiophene π‐bridge on the polymers' optical and electrochemical properties was investigated. Electrochemical characterization indicated that these polymers have deep highest occupied molecular orbital energy levels between ?5.7 and ?5.8 eV. Polymer solar cells were fabricated by using these PMDI‐based polymers as the donor and [6,6]‐phenyl‐C61‐butyric acid methyl ester as the acceptor. The polymer P1 whose PMDI unit was functionalized with 2‐ethylhexyl side chain shows the higher short‐circuit current (J_sc) and fill factor (FF) compared with that of P2 with a 2‐octyldodecyl side chain on the PMDI unit. The results also illustrate that the insertion of a thiophene π‐bridge between PMDI and TT (the polymer P3) leads to the broader absorption and better photovoltaic performance. The best performance was obtained from the cell based on the polymer P3 with a power conversion efficiency of 0.43% under the illumination of AM 1.5 G, 100 mW/cm². Copyright © 2014 John Wiley & Sons, Ltd.     

A room-temperature heptazine core discotic liquid crystal

Heptazine is the fundamental structural and functional unit of graphitic carbon nitrides and has a π-conjugated planar symmetry with semiconducting properties. Molecular self-assembly is one of the key factors to drive the electronic behaviour of π-conjugated organic molecules. To enhance the semiconductivity, heptazine is decorated at its active sites with 2,3,5-tris(dodecyloxy)aniline to get well-organised columnar packing. A novel heptazine-core room-temperature discotic liquid crystal (HDLC) with hexagonal columnar geometry is discovered. The molecular structure and mesomorphic properties of HDLC are investigated by ¹H-NMR, ¹³C-NMR, IR, polarised optical microscopy, differential scanning calorimetry and X-ray diffraction. Photophysical and electrochemical properties of HDLC are studied by UV–vis/fluorescence spectroscopy and cyclic voltammetry (CV), respectively. The energy band gap of HDLC estimated from CV at room temperature is 1.63 eV, which is much narrower than the previously reported band gap for heptazine derivatives. This decrease in the energy band can be attributed to the particular designing of HDLC for columnar packing. As a columnar liquid crystal providing a smooth path to the charge transport, HDLC with such a narrow energy band gap may find applications in organic electronics.     

Novel blue‐greenish electroluminescent poly(fluorenevinylene‐alt‐dibenzothiophenevinylene)s and their model compounds

Poly(9,9‐dihexylfluorene‐2,7‐vinylene‐alt‐dibenzothiophene‐2,8‐vinylene) (PS) and poly(9,9‐dihexylfluorene‐2,7‐vinylene‐alt‐dibenzothiophene‐5,5‐dioxide‐2,8‐ vinylene) (PSO) as well as corresponding model compounds were synthesized by Heck coupling. Both the polymers and model compounds were readily soluble in common organic solvents such as tetrahydrofuran, dichloromethane, chloroform, and toluene. The polymers showed a decomposition temperature at ～430 °C and a char yield of about 65% at 800 °C in N₂. The glass‐transition temperatures of the polymers were almost identical (75–77 °C) and higher than those of the model compounds (26–45 °C). All samples absorbed around 390 nm, and their optical band gaps were 2.69–2.85 eV. They behaved as blue‐greenish light emitting materials in both solutions and thin films, with photoluminescence emission maxima at 450–483 nm and photoluminescence quantum yields of 0.52–0.72 in solution. Organic light‐emitting diodes with an indium tin oxide/poly(ethylene dioxythiophene):poly(styrene sulfonic acid)/polymer/Mg:Ag/Ag configuration with polymers PS and PSO as emitting layers showed green electroluminescence with maxima at 530 and 540 nm, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6790–6800, 2006