Physicochemical Characterization of Acidiphilium sp. Biofilms

The biofilm formation of a strain of the extremophile bacterium Acidiphilium sp., capable of donating electrons directly to electrodes, was studied by different surface characterization techniques. We develop a method that allows the simultaneous study of bacterial biofilms by means of fluorescence microscopy and atomic force microscopy (AFM), in which transparent graphitic flakes deposited on a glass substrate are used as a support for the biofilm. The majority of the cells present on the surface were viable, and the growth of the biofilms over time showed a critical increase of the extracellular polymeric substances (EPS) as well as the formation of nanosized particles inside the biofilm. Also, the presence of Fe in Acidiphilium biofilms was determined by X‐ray photoelectron spectroscopy (XPS), whereas surface‐enhanced infrared absorption spectroscopy indicated the presence of redox‐active proteins.     

Effects of operating conditions on the adhesive strength of Pseudomonas fluorescens biofilms in tubes

Understanding the mechanical properties of biofilms, especially the force required to disrupt them and remove them from substrata is very important to development of antibiofouling strategies. In this work, a novel micromanipulation technique with a specially designed T-shaped probe has been developed to serve as an experimental means to measure directly the adhesive strength of biofouling deposits on the surface of a glass test stud. The basic principle of this novel technique is to pull away a whole biofilm accumulated on the surface of a glass test stud with T-shaped probe, and to measure simultaneously the force imposed on the biofilm. The adhesive strength between the biofilms and the surface to which they are attached, is defined as the work per unit area required to remove the biofilms from the surface. The biofouling experiments were performed on an elaborate design of a simulated heat exchanger system. A monoculture of Pseudomonas fluorescens was chosen as the fouling microorganism for the laboratory studies. Results indicate that the adhesive strength of the biofilm was affected by the conditions of operation, such as biofilm age, nutrient concentration, suspended cell concentration, pH, surface roughness of the substratum and fluid velocity. As noted, the effect of fluid velocity on the biofilm adhesive strength seemed to overwhelm other factors. At the same operating conditions, the biofilm adhesive strength increased as the fluid velocity increased within the range of 0.6-1.6m/s. In addition, the flow-related biofilm structures were observed that biofilms generally grew as a more compact pattern at the higher fluid velocity. Apparently, the fluid velocity can affect the biofilm structure, which in turn determines the biofilm adhesive strength. The knowledge of the biofilm adhesive strength with associated influences of the operating conditions may be used to define better cleaning procedures.     

The role of conditioning film formation and surface chemical changes on Xylella fastidiosa adhesion and biofilm evolution

Biofilms are complex microbial communities with important biological functions including enhanced resistance against external factors like antimicrobial agents. The formation of a biofilm is known to be strongly dependent on substrate properties including hydrophobicity/hydrophilicity, structure, and roughness. The adsorption of (macro)molecules on the substrate, also known as conditioning film, changes the physicochemical properties of the surface and affects the bacterial adhesion. In this study, we investigate the physicochemical changes caused by Periwinkle wilt (PW) culture medium conditioning film formation on different surfaces (glass and silicon) and their effect on X. fastidiosa biofilm formation. Contact angle measurements have shown that the film formation decreases the surface hydrophilicity degree of both glass and silicon after few hours. Atomic force microscopy (AFM) images show the glass surface roughness is drastically reduced with conditioning film formation. First-layer X. fastidiosa biofilm on glass was observed in the AFM liquid cell after a period of time similar to that determined for the hydrophilicity changes. In addition, attenuation total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy supports the AFM observation, since the PW absorption spectra increases with time showing a stronger contribution from the phosphate groups. Although hydrophobic and rough surfaces are commonly considered to increase bacteria cell attachment, our results suggest that these properties are not as important as the surface functional groups resulting from PW conditioning film formation for X. fastidiosa adhesion and biofilm development.     

Effect of roughness on particle adhesion in aqueous solutions: a study of Saccharomyces cerevisiae and a silica particle

An atomic force microscope (AFM) has been used to quantify the adhesion of living cells Saccharomyces cerevisiae on three different silica surfaces with defined roughness. The effects of support roughness on the adhesion forces of a smooth silica particle were studied in addition. A living single cell was immobilized at the apex of a tipless AFM cantilever using a key-lock mechanism. Adhesion was quantified from the force-distance data measured on a smooth silica substrate and two substrates coated with hydrophilic monodisperse silica particles with 110 and 240 nm in diameter to study the effect of roughness on particle adhesion. The AFM technique gives unique insight into the primary colonization event of biofilm formation. The new knowledge helps substantially to design surface coatings relevant for biotechnology, medicine and dentistry.     

Small molecule control of bacterial biofilms

Bacterial biofilms are defined as a surface attached community of bacteria embedded in a matrix of extracellular polymeric substances that they have produced. When in the biofilm state, bacteria are more resistant to antibiotics and the host immune response than are their planktonic counterparts. Biofilms are increasingly recognized as being significant in human disease, accounting for 80% of bacterial infections in the body and diseases associated with bacterial biofilms include: lung infections of cystic fibrosis patients, colitis, urethritis, conjunctivitis, otitis, endocarditis and periodontitis. Additionally, biofilm infections of indwelling medical devices are of particular concern, as once the device is colonized infection is virtually impossible to eradicate. Given the prominence of biofilms in infectious diseases, there has been an increased effort toward the development of small molecules that will modulate bacterial biofilm development and maintenance. In this review, we highlight the development of small molecules that inhibit and/or disperse bacterial biofilms through non-microbicidal mechanisms. The review discuses the numerous approaches that have been applied to the discovery of lead small molecules that mediate biofilm development. These approaches are grouped into: (1) the identification and development of small molecules that target one of the bacterial signaling pathways involved in biofilm regulation, (2) chemical library screening for compounds with anti-biofilm activity, and (3) the identification of natural products that possess anti-biofilm activity, and the chemical manipulation of these natural products to obtain analogues with increased activity.     

Atomic force microscopy of microvillous cell surface dynamics at fixed and living alveolar type II cells

Scanning probe techniques enable direct imaging of morphology changes associated with cellular processes at life specimen. Here, glutaraldehyde-fixed and living alveolar type II (ATII) cells were investigated by atomic force microscopy (AFM), and the obtained topographical data were correlated with results obtained by scanning electron microscopy (SEM) and confocal microscopy (CM). We show that low-force contact mode AFM at glutaraldehyde-fixed cells provides complementary results to SEM and CM. Both AFM and SEM images reveal fine structures at the surface of fixed cells, which indicate microvilli protrusions. If ATII cells were treated with Ca²⁺ channel modulators known to induce massive endocytosis, changes of the cell surface topography became evident by the depletion of microvilli. Low force contact mode AFM imaging at fixed ATII cells revealed a significant reduction of the surface roughness for capsazepine and 2-aminoethoxydiphenyl-borate (CPZ/2-APB)-treated cells compared to untreated control cells (Rc of 99.7 ± 6.8 nm vs. Rc of 71.9 ± 4.6 nm for N = 22), which was confirmed via SEM studies. CM of microvilli marker protein Ezrin revealed a cytoplasmic localization of Ezrin in CPZ/2-APB-treated cells, whereas a submembranous Ezrin localization was observed in control cells. Furthermore, in situ AFM investigations at living ATII cells using low force contact mode imaging revealed an apparent decrease in cell height of 17% during stimulation experiments. We conclude that a dynamic reorganization of the microvillous cell surface occurs in ATII cells at conditions of stimulated endocytosis.     

Microfluidic approaches to bacterial biofilm formation

Bacterial biofilms-aggregations of bacterial cells and extracellular polymeric substrates (EPS)-are an important subject of research in the fields of biology and medical science. Under aquatic conditions, bacterial cells form biofilms as a mechanism for improving survival and dispersion. In this review, we discuss bacterial biofilm development as a structurally and dynamically complex biological system and propose microfluidic approaches for the study of bacterial biofilms. Biofilms develop through a series of steps as bacteria interact with their environment. Gene expression and environmental conditions, including surface properties, hydrodynamic conditions, quorum sensing signals, and the characteristics of the medium, can have positive or negative influences on bacterial biofilm formation. The influences of each factor and the combined effects of multiple factors may be addressed using microfluidic approaches, which provide a promising means for controlling the hydrodynamic conditions, establishing stable chemical gradients, performing measurement in a high-throughput manner, providing real-time monitoring, and providing in vivo-like in vitro culture devices. An increased understanding of biofilms derived from microfluidic approaches may be relevant to improving our understanding of the contributions of determinants to bacterial biofilm development.     

Microbiologically influenced corrosion of 304 stainless steel by aerobic Pseudomonas NCIMB 2021 bacteria: AFM and XPS study

Microbiologically influenced corrosion (MIC) of stainless steel 304 by a marine aerobic Pseudomonas bacterium in a seawater-based medium was investigated by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). AFM was used to observe in situ the proliferation of a sessile Pseudomonas cell by binary fission. The development of a biofilm on the coupon surface and the extent of corrosion damage beneath the biofilm after various exposure times were also characterized by AFM. Results showed that the biofilm formed on the coupon surface increased in thickness and heterogeneity with time, and thus resulting in the occurrence of extensive micro-pitting corrosion; whilst the depth of pits increased linearly with time. The XPS results confirmed that the colonization of Pseudomonas bacteria on the coupon surface induced subtle changes in the alloy elemental composition in the outermost layer of surface films. The most significant feature resulting from microbial colonization on the coupon surface was the depletion of iron (Fe) and the enrichment of chromium (Cr) content as compared to a control coupon exposed to the sterile medium, and the enrichment of Cr increased with time. These compositional changes in the main alloying elements may be correlated with the occurrence of extensive micropitting corrosion on the surface.     

Predation, death, and survival in a biofilm: Bdellovibrio investigated by atomic force microscopy

Biofilms are complex microbial communities that are resistant to attack by bacteriophages and to removal by drugs and chemicals. Here we use atomic force microscopy (AFM) to image the attack on Escherichia coli biofilms by Bdellovibrio bacteriovorus 109J. Bdellovibrio is a small, predatory bacterium that invades and devours other Gram-negative bacteria. We demonstrate that under dilute nutrient conditions, bdellovibrios can prevent the formation of simple bacterial biofilms and destroy established biofilms; under richer conditions the prey bacteria persist and are not eradicated, but may be shifted toward solution populations. Using AFM we explore these bacterial interactions with more detail and accuracy than available by more traditional staining assays or optical microscopy. AFM also allows us to investigate the nanoscale morphological changes of the predator, especially those related to motility. This demonstration of Bdellovibrio's successful predation in a biofilm inspires us to consider ways that it might be used productively for industrial, medical, agricultural, and biodefensive purposes.     

Control of surface topography in biomimetic calcium phosphate coatings

The behavior of cells responsible for bone formation, osseointegration, and bone bonding in vivo are governed by both the surface chemistry and topography of scaffold matrices. Bone-like apatite coatings represent a promising method to improve the osteoconductivity and bonding of synthetic scaffold materials to mineralized tissues for regenerative procedures in orthopedics and dentistry. Polycaprolactone (PCL) films were coated with calcium phosphates (CaP) by incubation in simulated body fluid (SBF). We investigated the effect of SBF ion concentration and soaking time on the surface properties of the resulting apatite coatings. CaP coatings were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectrometry (FTIR), and energy dispersive X-ray spectrometry (EDX). Young's modulus (E(s)) was determined by nanoindentation, and surface roughness was assessed by atomic force microscopy (AFM) and mechanical stylus profilometry. CaP such as carbonate-substituted apatite were deposited onto PCL films. SEM and AFM images of the apatite coatings revealed an increase in topographical complexity and surface roughness with increasing ion concentration of SBF solutions. Young's moduli (E(s)) of various CaP coatings were not significantly different, regardless of the CaP phase or surface roughness. Thus, SBF with high ion concentrations may be used to coat synthetic polymers with CaP layers of different surface topography and roughness to improve the osteoconductivity and bone-bonding ability of the scaffold.     

Electrochemical characterization of anodic biofilms enriched with glucose and acetate in single-chamber microbial fuel cells

This study used a simple and efficient electrochemical technique, cyclic voltammogram (CV), to quantitatively measure the electron transfer capability of anodic biofilms enriched with acetate and glucose in single-chamber microbial fuel cells (MFCs). Two pairs of distinct redox peaks were observed by CV measurements in both biofilms, identical to the CV features of a pure Geobacter strain. The CVs also revealed a higher density of electroactive species in the acetate-enriched biofilm than that in the glucose-enriched biofilm. Based on the scan rate analysis, the apparent electron transfer rate constants (k(app)) in the acetate-enriched biofilm and glucose-enriched biofilm were determined to be 0.82 and 0.15s(-1), respectively, which supported the higher power output of the MFC fed with acetate. Meanwhile, the pH dependence of the biofilms was studied by monitoring the changes of the biofilm redox peak currents and potentials. It is concluded that redox reaction of the electrochemical active species in biofilms is pH dependent, and both electrons and protons are involved in the redox reactions.     

Cell adhesion and surface properties of polystyrene surfaces grafted with poly(N-isopropylacrylamide)

Cell adhesion plays a key role in various aspects of biological and medical sciences. In this study, poly(Nisopropylacrylamide) (PNIPAM) was grafted on polystyrene surfaces using different solvents under UV radiation. Moreover, the relation between surface roughness and cell adhesion were evaluated by gravimetric, SEM, AFM, contact angle measurement and cellular analyses. The gravimetric analysis clearly indicated an increase in the grafting by adding 10% methanol to water. The study of surface topography by AFM images showed an increase in the surface roughness and as a result of which, a decrease in wettablity was observed. At 37 °C, epithelial cells were well attached and proliferated on the grafted surfaces, while these cells were spontaneously detached below 32 °C in the absence of any enzymes. Moreover, MTT assay and SEM images indicated good cell viability and an increase in cell adhesion caused by the roughness increase. The results of this study reveal the great potential of PNIPAM-grafted polystyrene for being used in the biomedical fields such as drug delivery systems, tissue engineering and cell separation.     

Oligonucleotide nanostructured surfaces: effect on Escherichia coli curli expression

Oligonucleotide model surfaces allowing independent variation of topography and chemical composition were designed to study the adhesion and biofilm growth of E.coli. Surfaces were produced by covalent binding of oligonucleotides and immobilization of nucleotide-based vesicles. Their properties were confirmed through a combination of fluorescence microscopy, XPS, ellipsometry, AFM and wettability studies at each step of the process. These surfaces were then used to study the response of three different strains of E.coli quantified in a static biofilm growth mode. This study led to convincing evidence that oligonucleotide-modified surfaces, independent of the topographical feature used in this study, enhanced curli expression without an increase in the number of adherent bacteria.     

Identification of New Potential Inhibitors of Quorum Sensing through a Specialized Multi-Level Computational Approach

Biofilms are aggregates of microorganisms anchored to a surface and embedded in a self-produced matrix of extracellular polymeric substances and have been associated with 80% of all bacterial infections in humans. Because bacteria in biofilms are less amenable to antibiotic treatment, biofilms have been associated with developing antibiotic resistance, a problem that urges developing new therapeutic options and approaches. Interfering with quorum-sensing (QS), an important process of cell-to-cell communication by bacteria in biofilms is a promising strategy to inhibit biofilm formation and development. Here we describe and apply an in silico computational protocol for identifying novel potential inhibitors of quorum-sensing, using CviR—the quorum-sensing receptor from Chromobacterium violaceum—as a model target. This in silico approach combines protein-ligand docking (with 7 different docking programs/scoring functions), receptor-based virtual screening, molecular dynamic simulations, and free energy calculations. Particular emphasis was dedicated to optimizing the discrimination ability between active/inactive molecules in virtual screening tests using a target-specific training set. Overall, the optimized protocol was used to evaluate 66,461 molecules, including those on the ZINC/FDA-Approved database and to the Mu.Ta.Lig Virtual Chemotheca. Multiple promising compounds were identified, yielding good prospects for future experimental validation and for drug repurposing towards QS inhibition.     

Towards a nondestructive chemical characterization of biofilm matrix by Raman microscopy

In this study, the applicability of Raman microscopy (RM) for nondestructive chemical analysis of biofilm matrix, including microbial constituents and extracellular polymeric substances (EPS), has been assessed. The examination of a wide range of reference samples such as biofilm-specific polysaccharides, proteins, microorganisms, and encapsulated bacteria revealed characteristic frequency regions and specific marker bands for different biofilm constituents. Based on received data, the assignment of Raman bands in spectra of multispecies biofilms was performed. The study of different multispecies biofilms showed that RM can correlate various structural appearances within the biofilm to variations in their chemical composition and provide chemical information about a complex biofilm matrix. The results of RM analysis of biofilms are in good agreement with data obtained by confocal laser scanning microscopy (CLSM). Thus, RM is a promising tool for a label-free chemical characterization of different biofilm constituents. Moreover, the combination of RM with CLSM analysis for the study of biofilms grown under different environmental conditions can provide new insights into the complex structure/function correlations in biofilms.     

Efflux Pump Inhibitor Potentiates Antimicrobial Photodynamic Inactivation of Enterococcus faecalis Biofilm

Microbial biofilm architecture contains numerous protective features, including extracellular polymeric material that render biofilms impermeable to conventional antimicrobial agents. This study evaluated the efficacy of antimicrobial photodynamic inactivation (aPDI) of Enterococcus faecalis biofilms. The ability of a cationic, phenothiazinium photosensitizer, methylene blue (MB) and an anionic, xanthene photosensitizer, rose bengal (RB) to inactivate biofilms of E. faecalis (OG1RF and FA 2-2) and disrupt the biofilm structure was evaluated. Bacterial cells were tested as planktonic suspensions, intact biofilms and biofilm-derived suspensions obtained by the mechanical disruption of biofilms. The role of a specific microbial efflux pump inhibitor (EPI), verapamil hydrochloride in the MB-mediated aPDI of E. faecalis biofilms was also investigated. The results showed that E. faecalis biofilms exhibited significantly higher resistance to aPDI when compared with E. faecalis in suspension (P < 0.001). aPDI with cationic MB produced superior inactivation of E. faecalis strains in a biofilm along with significant destruction of biofilm structure when compared with anionic RB (P < 0.05). The ability to inactivate biofilm bacteria was further enhanced when the EPI was used with MB (P < 0.001). These experiments demonstrated the advantage of a cationic phenothiazinium photosensitizer combined with an EPI to inactivate biofilm bacteria and disrupt biofilm structure.     

Roughness and hydrophobicity studies of nanofiltration membranes using different modes of AFM

Determination of the surface roughness by AFM is crucial to the study of particle fouling in nanofiltration. It is, however, very difficult to compare the different roughness values reported in the literature because of a lack in uniformity in the methods applied to determine surface roughness. AFM is used in both noncontact mode and tapping mode; moreover, the size of the scan area is highly variable. This study compares, for six different nanofiltration membranes (UTC-20, N30F, Desal 51HL, Desal 5DL, NTR7450, NF-PES-10), noncontact mode AFM with tapping mode AFM for several sizes of the scan area. Although the absolute roughness values are different for noncontact AFM and tapping mode AFM, no difference is found between the two modes of AFM in ranking the nanofiltration membranes with respect to their surface roughness. NTR 7450 and NF-PES-10 are the smoothest membranes, while the roughest surface can be found with Desal 51HL and Desal 5DL. UTC-20 and N30F are characterized by an intermediate roughness value. An increase in roughness with increasing scan area is observed for both AFM modes. Larger differences between the roughnesses of the membranes are obtained with tapping mode AFM because of the tapping of the tip on the surface. Phase imaging is an extension of tapping mode AFM, measuring the phase shift between the cantilever oscillation and the oscillation of the piezo driver. This phase shift reflects the interaction between the cantilever and the membrane surface. A comparison with contact angle measurements proves that a small phase shift corresponds to a large contact angle, representing a hydrophobic membrane surface.     

Disruption of urogenital biofilms by lactobacilli

The process that changes a relatively sparse vaginal microbiota of healthy women into a dense biofilm of pathogenic and potentially pathogenic bacteria is poorly understood. Likewise, the reverse step whereby an aberrant biofilm is displaced and returns to a healthy lactobacilli dominated microbiota is unclear. In order to study these phenomena, in vitro experiments were performed to examine the structure of biofilms associated with aerobic vaginosis, urinary tract infections, and bacterial vaginosis (BV). Uropathogenic Escherichia coli were able to form relatively thin biofilms within five days (6 μm height), while Atopobium vaginae and Gardnerella vaginalis formed thicker biofilms 12 μm in height within two days. Challenge of E. coli biofilms with lactobacilli did not result in pathogen displacement. However, the resulting thicker lactobacilli infused biofilms, caused significant E. coli killing. E. coli biofilms challenged with secreted products of L. rhamnosus GR-1 caused a marked decrease in cell density, and increased cell death. Similarly challenge of BV biofilms with lactobacilli infiltrated BV biofilms and caused bacterial cell death. Metronidazole produced holes in the biofilm but did not eradicate the organisms. The findings provide some evidence of how lactobacilli probiotics might interfere with an aberrant vaginal microbiota, and strengthen the position that combining probiotics with antimicrobials could better eradicate pathogenic biofilms.     

Comparative characterisation by atomic force microscopy and ellipsometry of soft and solid thin films

Ellipsometry and atomic force microscopy (AFM) were used to study the film thickness and the surface roughness of both ‘soft’ and solid thin films. ‘Soft’ polymer thin films of polystyrene and poly(styrene–ethylene/butylene–styrene) block copolymer were prepared by spin‐coating onto planar silicon wafers. Ellipsometric parameters were fitted by the Cauchy approach using a two‐layer model with planar boundaries between the layers. The smooth surfaces of the prepared polymer films were confirmed by AFM. There is good agreement between AFM and ellipsometry in the 80–130 nm thickness range. Semiconductor surfaces (Si) obtained by anisotropic chemical etching were investigated as an example of a randomly rough surface. To define roughness parameters by ellipsometry, the top rough layers were treated as thin films according to the Bruggeman effective medium approximation (BEMA). Surface roughness values measured by AFM and ellipsometry show the same tendency of increasing roughness with increased etching time, although AFM results depend on the used window size. The combined use of both methods appears to offer the most comprehensive route to quantitative surface roughness characterisation of solid films. Copyright © 2007 John Wiley & Sons, Ltd.     

Polysaccharide differences between planktonic and biofilm-associated EPS from Pseudomonas fluorescens B52

The polysaccharides associated with free (planktonic) and surface-attached (biofilm) cells from cultures of Pseudomonas fluorescens strain B52 were compared. Variations in the attached matrix due to surface material (glass or stainless steel) were also analyzed. Two digestion methods were used to optimize the recoveries of sugars, uronic acids and acidic substituents. The yield of analyzable material after digestion reached 90% for the material associated to the biofilms, though only 20–30% for that bound to planktonic cells. The polysaccharide(s) in the biofilm had glucuronic and guluronic acids as main components, besides rhamnose, glucose and glucosamine. The proportion of glucuronic to guluronic acid was higher in the polysaccharide(s) found in biofilms formed on stainless steel than in those on glass.