Liquid crystal alignment behaviours on poly(methyl methacrylate) having polyhedral oligomeric silsesquioxane groups

A series of poly(methyl methacrylate) derivatives containing polyhedral oligomeric silsesquioxane (POSS) groups (MCP#) were synthesised via free radical polymerisation (FRP) using methacryl isobutyl POSS (MA-POSS) and methyl methacrylate as monomers to investigate liquid crystal (LC) alignment property of these polymer films. The LC cells made from the films of the polymers having 100 mol% of MA-POSS units (MCP100) showed vertical LC alignment having a pretilt angle of about 90°. The vertical LC alignment behaviour on the MCP100 film was ascribed to the very hydrophobic MCP100 surface having the surface energy value smaller than about 23 mJ/m² generated by the nonpolar bulky POSS group. Good electro-optical characteristics, such as voltage holding ratio (VHR) and residual DC voltage (R-DC), were observed for the LC cells fabricated using MCP100 as a LC alignment layer.     

Liquid crystal alignment properties of 2-naphthoxymethyl-substituted polystyrenes

The liquid crystal (LC) alignment properties of LC cells fabricated with films of 2-naphthoxymethyl-substituted polystyrenes with different contents of naphthoxymethyl side groups were investigated. The polymer films exhibited good optical transparency in the visible light region (400–700 nm). The LC cells made from the unrubbed films of polymers having more than 57 mol%?of 2-naphthoxymethyl containing monomeric units showed homeotropic LC alignment with a high pretilt angle of about 90^o. Good electro-optical characteristics, such as the threshold voltage, response time, voltage holding ratio and residual DC voltage were observed for the LC cells fabricated with the polymer having 100 mol%?of 2-naphthoxymethyl containing monomeric units as an LC alignment layer.     

Vertical alignment of liquid crystal on tocopherol-substituted polystyrene films

We synthesised a series of vitamin-based and renewable tocopherol-substituted polystyrene (PTOC#, # = 20, 40, 60, 80 and 100), where # is the molar content of tocopherol moiety, using polymer analogous reactions to investigate their liquid crystal (LC) alignment properties. In general, the LC cell fabricated using the polymer film having a higher molar content of tocopherol side group showed vertical LC alignment behaviour. The vertical alignment (VA) behaviour was well correlated with the surface energy value of these polymer films. For example, VA was observed when the surface energy values of the polymer were smaller than about 35.22 mJ/m² generated by the nonpolar tocopherol moiety having long and bulky carbon groups. Good electro-optical characteristics, such as voltage holding ratio and residual DC voltage, and aligning stabilities at 200°C and ultraviolet irradiation of 10 J/cm² were observed for the LC cells fabricated using PTOC100 as a LC alignment layer. Therefore, it was first found that the renewable tocopherol-based materials can produce an eco-friendly vertical LC alignment system.     

Liquid crystal alignment properties of n-alkylsulphonylmethyl-substituted polyoxyethylenes

The liquid crystal (LC) alignment properties of LC cells fabricated with films of n-alkylsulphonylmethyl-substituted polyoxyethylenes (#S-PEO, #?=?4, 6, 7, 8 and 10), where # is the number of carbon atoms in the n-alkyl side groups having different n-alkyl chain length, were investigated as a function of the rubbing density. The LC cells made from unrubbed #S-PEO (# ≥8) films having more than eight carbon atoms in the n-alkyl side groups showed homeotropic LC alignment. The homeotropic LC alignment behaviour correlated well with the surface energy values of the unrubbed #S-PEO films; homeotropic LC alignment was observed when the surface energy values of the unrubbed #S-PEO films were smaller than about 21.62 mJ m^?2. The LC cells made from rubbed #S-PEO (# ≥7) films having more than seven carbon atoms with a rubbing density of 150 showed homeotropic LC alignment. It was also found that the tilt angle of the LCs on the rubbed #S-PEO films was affected not only by the n-alkyl chain length of the polymers, but also by the rubbing density, regardless of the surface energy value of the #S-PEO film.     

Homogeneous liquid crystal orientation on ion beam exposure TiO2 surfaces depending on an anisotropic dipole field

We studied homogeneous liquid crystal (LC) alignment properties on ion-beam (IB) irradiated TiO₂ films deposited by the electron beam evaporation method. Stable homogeneous LC alignment on a TiO₂ surface resulted from IB irradiation energy over 1800 eV. X-ray photoelectron spectroscopy analyses showed that Ti⁴⁺ 2p_3/2 and Ti⁴⁺ 2p_1/2 peaks were increased with increasing IB energy. Assuming that the increased peaks produced anisotropy dipole fields in the direction of the IB exposure process, we confirmed that the increasing IB energy induced strengthened the surface energy for entirely clear and stable LC molecule orientation. The voltage-transmittance characteristics of the twisted-nematic cell on the TiO₂ surface indicate that the TiO₂ film has potential for use as the LC alignment layer.     

Orientation of liquid crystal molecules in polydimethylsiloxane micro-channels

The orientation of liquid crystal (LC) molecules confined in polydimethylsiloxane micro-channels, which are produced using mould-replica technique, with a rectangular cross section, is studied. The rod-like molecules of the LC adopt the vertical anchoring at every surface of the channels. The macroscopic alignment of the confined LC can be changed by altering the aspect ratio of the channels. The change in the macroscopic alignment of the LC is attributed directly to the restructuring of the proportion of the number of molecules anchored to the respective surfaces due to the changes in specific area of the bounding surface of the channels. Solutions for the elastic energy function obtained using conformal mapping method were used to predict director profile of the LC in the confinement.     

Polyimide-free homogeneous photoalignment induced by polymerisable liquid crystal containing cinnamate moiety

We designed and synthesised a reactive mesogen (CRM) containing cinnamate moiety in the core and two acrylate groups at both ends. The structure was characterised by ¹H NMR and FT-IR, and its liquid crystalline property was investigated by DSC and POM. The compound showed a nematic phase between 175.2 – 97.5 ^oC, followed by a smectic C phase between 97.5 and 57.9 ^oC during the cooling cycle. We proposed a fabrication method to achieve uniaxial homogeneous alignment of liquid crystals by irradiating the CRM-doped LC mixture in a sandwich cell of in-plane switching mode (CRM-IPS) with linearly polarised ultraviolet light. The results indicated that the CRM-IPS cell showed excellent initial dark state with a good alignment state, electro-optical performance and durability. This confirmed that the photo-induced alignment of LCs by CRM possesses outstanding alignment capability compared to the conventional rubbed polyimide alignment layer. We expect that this fabrication method is a promising candidate for cost-effective, green-manufacturing, and high-quality alignment method for the manufacturing of high-resolution liquid crystal displays (LCDs).     

Liquid crystal alignment properties of poly(styrenesulphonate)/alkyltrimethylammonium complexes

We synthesised a series of poly(4-styrenesulphonate)/alkyltrimethylammonium (PSS-#Cx, # = 12, 14 and 16; x?=?80, 60, 40 and 20) complexes, where # is the number of carbon atoms in the alkyl groups in alkyltrimethylammonium bromide, and x is the molar content (%) of alkyltrimethylammonium moiety, using polymer analogous reactions to investigate their liquid crystal (LC) alignment properties. In general, the LC cell fabricated using the polymer film having a longer alkyl side group and a higher molar content of alkyl side group showed homeotropic LC alignment behaviour with a pretilt angle of about 90°. The homeotropic LC alignment behaviour was well correlated with the surface energy of the polymer films. Homeotropic LC alignment was observed when the surface energy values of the polymer were smaller than about 44.87 mJ/m².     

Hyperbranched polyimide application in liquid crystal alignment layers

Several hyperbranched polyimides (HBPIs) were applied in liquid crystal (LC) alignment layers and exhibited outstanding performance for LC alignment. The maximum pretilt angle was above 8°, and the minimum pretilt angle was 4.2°. The results of atomic force microscope measurement disclosed that a lot of grooves were aligned parallel to the rubbing direction and found that the grooves were not main factor for LC alignment. The LC alignment and pretilt angles are unambiguously associated with the intrinsic HBPI chemical structures. The results of thermal gravimetric analysis and ultraviolet–visible spectra showed that the HBPIs had good thermal stability and excellent transmittance. T₅ and T₁₀ were higher than 360°C and 400°C, respectively. Copyright © 2012 John Wiley & Sons, Ltd.     

Bent-core liquid crystal-functionalised flexible polymer substrates for liquid crystal alignment

ABSTRACT

A transparent flexible polymer film is chemically functionalised with a bent-core liquid crystal (BCLC) compound for effective alignment of the bulk BCLC sample at the substrate–LC interface. The surface attachment was achieved via a simple procedure which involved pre-treatment of the polymer film (commercial name: over head projector film) using piranha solution followed by chemically attaching the BCLC compound through silane condensation reaction. Surface characterisation of the unmodified and BC-modified flexible films was carried out through X-ray photoelectron spectroscopy (XPS), attenuated total reflectance fourier transform infrared (ATR-FTIR) spectroscopy, contact angle (CA) and atomic force microscopy (AFM) techniques. The BC-modified flexible substrates are analysed for their efficiency to orient the bulk LC sample. Remarkably, the chemically modified polymer substrates are highly efficient in vertically aligning both the BC and rod-like LC samples at the substrate–LC interface, in comparison to their unmodified counterparts. The described method is simple, reproducible, surface modified substrates are highly stable and more importantly reusable. The demonstrated method for the alignment of BCLCs advances a step forward towards the realisation of applications proposed for these fascinating compounds.     

The effect of surface polarity of glass on liquid crystal alignment

The effects of the surface polarity of a glass substrate on the orientation of nematic liquid crystals (LCs) were studied using the polarised optical microscope and Fourier-transform infrared spectroscopy. On the surface of oxygen plasma treated glass, a homeotropic alignment of LCs was induced for LCs with negative dielectric anisotropy. This suggests that vertical orientation of LCs could be induced on a polar glass substrate without using an LC alignment layer. Upon cooling towards the isotropic–nematic transition, E7 with positive dielectric anisotropy changes its LC arrangement to isotropic, homeotropic, planar orientations in order. The nematic LC anchoring transition of E7 was interpreted by considering the competition between van der Waals forces and dipole interactions that control the alignment of LC molecules on a polar glass surface.     

Fabrication of homogenously self-alignment fringe-field switching mode liquid crystal cell without using a conventional alignment layer

We propose a novel method to fabricate a uniaxially homogeneous alignment of liquid crystal (LC) molecules without using a conventional alignment layer such as polyimide film. The method produces the polymer alignment layer (PAL) by polymerisation of the monomer including in the LC layer above the T_NI of the LC material. The fringe-field switching (FFS) mode LC cell with the PAL (FFS-PAL-LC cell) produced from the monomer 4,4?-di-mehacryloyl-oxy chalcone (4,4?-DMOCh) exhibited enough level of alignment state and electro-optical property compared with the FFS-LC cell having the conventional polyimide-type alignment layer. We can expect that the FFS-PAL-LC cell is useful for next-generation displays such as flexible liquid crystal displays (LCDs) because the method does not need high-temperature process of over 200°C.     

Preparation and characterization of a novel polyimide liquid crystal vertical alignment layer

A series of diamines with a side chain containing rigid biphenyl unit and nonpolar alkoxy side end group [4-alkoxy-biphenol-3′,5′-diaminobenzoate] (Cm-BBDA, m = 4, 6, 12) were synthesized and their chemical structures were confirmed by Fourier Transform Infrared Spectroscopy (FT-IR) and nuclear magetic resonance spectroscopy (¹H NMR). Then three polyimides (PIs) were prepared by copolymerization of pyromellitic dianhydride (PMDA), 4,4′-methylenedianiline (MDA) and Cm-BBDA in N-methyl-2-pyrrolodone (NMP), and chemical structures of all PIs were confirmed by FT-IR. Structural identification of all poly(amic acid)s (PAA) was performed by ¹H NMR. Liquid crystal (LC) cells were fabricated using these PIs as the alignment layer for characterization of the alignment properties of LCs. It was found that the planar alignment was obtained when PI with side chain containing alkoxy side end group of 4 carbon atoms was employed and the vertical alignment was observed when alkoxy side end groups of 6 or 12 carbon atoms were included. A uniform vertical alignment was validated by polarizing microscopy. It was testified that LC vertical alignment possessed high thermal stability.     

Fabrication of vertically aligned liquid crystal cell without using a conventional alignment layer

We propose a novel method to fabricate a vertical alignment (VA) of liquid crystal (LC) molecules without using a conventional alignment layer such as polyimide film. The method produces the vertical alignment polymer layer (VAPL) by polymerisation of a monomer or mixed monomers including in the LC layer above T_NI of the LC material. The VA mode LC cell with the VAPL (VAPL-LC cell) produced from the mixed monomers of acrylic acid 4-(4?-octyloxy-biphenyl-4-yloxy)-butyl ester and 1,2-bis-(4-methacryloxy-phenyl)-2,2-dimethoxy-ethane-1-one exhibited enough level of alignment state and electro-optical property with high voltage holding ratio. We can expect that the VAPL-LC cell is useful for next-generation displays such as flexible liquid crystal displays because the method does not need the process including high temperature over 200°C.     

A simple strategy for detecting synthetic polymers on solid surfaces using liquid crystal

In this study, we developed a liquid crystal (LC)-based detection method for polymer films synthesized on solid surfaces. A dark to bright transition in the optical appearance of nematic 4-cyano-4′-pentylbiphenyl (5CB) was observed after transferring a poly(methyl methacrylate) (PMMA) film onto a glass substrate functionalized with n-octyltrichlorosilane (OTS). This phenomenon indicates an orientational transition of 5CB from a homeotropic to a planar-random state. The optical response of 5CB was then evaluated directly through polymerization reactions on the OTS-functionalized glass substrate. Polymer films of PMMA, poly(glycidyl methacrylate) (PGMA), and poly(dimethylsiloxane) (PDMS) were synthesized on OTS surfaces covered with their reaction mixtures. All polymer films displayed bright signals of 5CB, which corresponded to the planar-random orientation of LCs. However, no change in orientation was observed for the control experiments. We confirmed the formation of polymer films on the OTS surface using atomic force microscopy. Overall, our results suggest that LCs can be used to construct optical monitoring systems for the product of polymerization reactions.

Homogeneously aligned liquid crystal molecules on unidirectional buckle pattern of polyurethane films

We present the fabrication of an anisotropic structure on a polyurethane (PU) film for aligning liquid crystal (LC) molecules with ion beam (IB) irradiation at an incident angle. The obtained anisotropic structure assembles the LC cells in a layer that aligns LC molecules uniformly. Polarised optical microscopy images of an LC cell fabricated with IB-irradiated PU were captured to confirm the LC alignment state and compared with those fabricated with non-treated PU. To analyse the effects of the IB irradiation, X-ray photoelectron spectroscopy and field-emission scanning electron microscopy were used to investigate the chemical and morphological modifications, respectively. IB irradiation modifies the chemical structure of PU, which indicates that a new skin layer is formed on the PU films. This skin layer generates an in-plane compressive strain, thereby creating buckles on the PU films. Simultaneously, the physical collision of the reactive Ar⁺ ions during IB irradiation induces a directional strain on the surface, thereby forming a unidirectional structure of buckles along the direction of IB irradiation. The PU film annealed at 200°C showed the high average transmittance of 88.9%, which is appropriate as an alignment layer.     

In situ self-assembled photo-switchable liquid crystal alignment layer using azosilane monomer-liquid crystal mixture system

Self-assembled monolayers (SAMs) are a unique approach for the liquid crystal (LC) alignment in electro-optical applications such as displays. Herein, a new methodology for photo-switchable LC alignment layer using an azosilane monomer and LC mixture system in the absence of any other foreign alignment layer is presented. The azosilane monomer spontaneously separated from the host LCs, and formed a stable monolayer network on the substrate surface. Data from X-ray photo-electron spectroscopy (XPS), spectroscopic elipsometry (SE), water contact angle and LC alignment studies confirmed that, in the azosilane and LC mixture system, azosilane makes an in situ SAM that is capable of photo-switchable LC alignment layer on glass and indium tin oxide (ITO) substrates. The LCs are aligned with respect to change in the photo-isomerisation of the azo molecule.     

Liquid crystal alignment property of n‐alkylthiomethyl‐ or n‐alkylsulfonylmethyl‐substituted polystyrenes

We synthesized a series of n‐alkylthiomethyl‐substituted polystyrenes (#T‐PS, # = 4, 8, 12, and 16) and n‐alkylsulfonylmethyl‐substituted polystyrenes (#S‐PS, # = 4, 8, 12, and 16), where # is the number of carbon atoms in the n‐alkyl side group of the polymers, using polymer analogous reactions to investigate their liquid crystal (LC) alignment properties. In general, the LC cell fabricated using the polymer film having a longer n‐alkyl side group, a thioether linkage group, and a higher molar content of n‐alkyl side group showed homeotropic LC alignment behavior with a pretilt angle of about 90°. The homeotropic alignment behavior was well correlated with the surface energy of the polymer films; when the positive dielectric anisotropic LC (ZLI‐5900‐000 from Merck) and negative dielectric anisotropic LC (MLC‐7026‐000 from Merck) were used to fabricate the LC cells, homeotropic alignment was observed when the surface energy values of the polymer were smaller than about 25 and 32 mJ/m², respectively. Copyright © 2009 John Wiley & Sons, Ltd.     

Langmuir films of flexible polymers transferred to aqueous/liquid crystal interfaces induce uniform azimuthal alignment of the liquid crystal

We reported recently that amphiphilic polymers can be assembled at interfaces created between aqueous phases and thermotropic liquid crystals (LCs) in ways that: (i) couple the organization of the polymer to the order of the LC and (ii) respond to changes in the properties of aqueous phases that can be characterized as changes in the optical appearance of the LC. This investigation sought to characterize the behavior of aqueous–LC interfaces decorated with uniaxially compressed thin films of polymers transferred by Langmuir–Schaefer (LS) transfer. Here, we report physicochemical characterization of interfaces created between aqueous phases and the thermotropic LC 4-cyano-4′-pentylbiphenyl (5CB) decorated with Langmuir films of a novel amphiphilic polymer (polymer 1), synthesized by the addition of hydrophobic and hydrophilic side chains to poly(2-vinyl-4,4′-dimethylazlactone). Initial characterization of this system resulted in the unexpected observation of uniform azimuthal alignment of 5CB after LS transfer of the polymer films to aqueous–5CB interfaces. This paper describes characterization of Langmuir films of polymer 1 hosted at aqueous–5CB interfaces as well as the results of our investigations into the origins of the uniform ordering of the LC observed upon LS transfer. Our results, when combined, support the conclusion that uniform azimuthal alignment of 5CB is the result of long-range ordering of polymer chains in the Langmuir films (in a preferred direction orthogonal to the direction of compression) that is generated during uniaxial compression of the films prior to LS transfer. Although past studies of Langmuir films of polymers at aqueous–air interfaces have demonstrated that in-plane alignment of polymer backbones can be induced by uniaxial compression, these past reports have generally made use of polymers with rigid backbones. One important outcome of this current study is thus the observation of anisotropy and long-range order in Langmuir films of a novel flexible polymer. A second important outcome is the observation that the existence, extent, and dynamics of this order can be identified and characterized optically by transfer of the Langmuir film to a thin film of LC. Additional characterization of Langmuir films of two other flexible polymers [poly(methyl methacrylate) and poly(vinyl stearate)] using this method also resulted in uniform azimuthal alignment of 5CB, suggesting that the generation of long-range order in uniaxially compressed Langmuir films of polymers may also occur more generally over a broader range of polymers with flexible backbones.     

Physicochemical analysis of ion beam-induced surface modifications on polyethylene glycol films for liquid crystal alignment

ABSTRACT

We investigated the surface modification induced by the ion-beam (IB) irradiation of a polyethylene glycol (PEG) film and its liquid crystal (LC) alignment characteristics. The X-ray photoelectron spectroscopy analysis revealed the chemical modification; as the IB incidence angle increased, the number of surface C–O bonds decreased, inducing an anisotropic dipole moment on the PEG film surface. In addition, the physical modification was demonstrated via atomic force microscopy analysis using three-dimensional images as a function of the IB incidence angle. The surface roughness was analyzed; the modification with the smoothest surface was observed for an IB incidence angle of 45°. This modification affected the LC alignment state of the PEG film, as demonstrated by the polarized optical microscopy analysis with pre-tilt angle measurements. Furthermore, for the same IB incidence angle, the residual DC measured using the capacitance–voltage curves was extremely low. Hence, a PEG film irradiated with an IB incidence angle of 45° could be a suitable LC alignment layer.