Liquid crystal alignment property of n‐alkylthiomethyl‐ or n‐alkylsulfonylmethyl‐substituted polystyrenes

We synthesized a series of n‐alkylthiomethyl‐substituted polystyrenes (#T‐PS, # = 4, 8, 12, and 16) and n‐alkylsulfonylmethyl‐substituted polystyrenes (#S‐PS, # = 4, 8, 12, and 16), where # is the number of carbon atoms in the n‐alkyl side group of the polymers, using polymer analogous reactions to investigate their liquid crystal (LC) alignment properties. In general, the LC cell fabricated using the polymer film having a longer n‐alkyl side group, a thioether linkage group, and a higher molar content of n‐alkyl side group showed homeotropic LC alignment behavior with a pretilt angle of about 90°. The homeotropic alignment behavior was well correlated with the surface energy of the polymer films; when the positive dielectric anisotropic LC (ZLI‐5900‐000 from Merck) and negative dielectric anisotropic LC (MLC‐7026‐000 from Merck) were used to fabricate the LC cells, homeotropic alignment was observed when the surface energy values of the polymer were smaller than about 25 and 32 mJ/m², respectively. Copyright © 2009 John Wiley & Sons, Ltd.     

Liquid crystal alignment properties of poly(styrenesulphonate)/alkyltrimethylammonium complexes

We synthesised a series of poly(4-styrenesulphonate)/alkyltrimethylammonium (PSS-#Cx, # = 12, 14 and 16; x?=?80, 60, 40 and 20) complexes, where # is the number of carbon atoms in the alkyl groups in alkyltrimethylammonium bromide, and x is the molar content (%) of alkyltrimethylammonium moiety, using polymer analogous reactions to investigate their liquid crystal (LC) alignment properties. In general, the LC cell fabricated using the polymer film having a longer alkyl side group and a higher molar content of alkyl side group showed homeotropic LC alignment behaviour with a pretilt angle of about 90°. The homeotropic LC alignment behaviour was well correlated with the surface energy of the polymer films. Homeotropic LC alignment was observed when the surface energy values of the polymer were smaller than about 44.87 mJ/m².     

Liquid crystal alignment properties of 2-naphthoxymethyl-substituted polystyrenes

The liquid crystal (LC) alignment properties of LC cells fabricated with films of 2-naphthoxymethyl-substituted polystyrenes with different contents of naphthoxymethyl side groups were investigated. The polymer films exhibited good optical transparency in the visible light region (400–700 nm). The LC cells made from the unrubbed films of polymers having more than 57 mol%?of 2-naphthoxymethyl containing monomeric units showed homeotropic LC alignment with a high pretilt angle of about 90^o. Good electro-optical characteristics, such as the threshold voltage, response time, voltage holding ratio and residual DC voltage were observed for the LC cells fabricated with the polymer having 100 mol%?of 2-naphthoxymethyl containing monomeric units as an LC alignment layer.     

Polar and azimuthal alignment of a nematic liquid crystal by alkylsilane self-assembled monolayers: effects of chain-length and mechanical rubbing

Alkylsilane self-assembled monolayers (SAMs) on oxide substrates are commonly used as liquid crystal (LC) alignment layers. We have studied the effects of alkyl chain length, photolytic degradation, and mechanical rubbing on polar and azimuthal LC anchoring. Both gradient surfaces (fabricated using photolytic degradation of C18 SAMs) and unirradiated SAMs composed of short alkyl chains show abrupt transitions from homeotropic to tilted alignment as a function of degradation or chain length. In both cases, the transition from homeotropic to tilted anchoring corresponds to increasing wettability of the SAM surfaces. However, there is an offset in the critical contact angle for the transition on gradient vs unirradiated SAMs, suggesting that layer thickness is more relevant than wettability for LC alignment. Mechanical rubbing can induce azimuthal alignment along the rubbing direction for alignment layers sufficiently near the homeotropic-to-planar transition. Notably, mechanical rubbing causes a small but significant shift in the homeotropic-to-tilted transition, e.g., unrubbed C5 SAMs induce homeotropic anchoring, but the same surface after rubbing induces LC pretilt.     

Smectic liquid crystal alignment using mechanically rubbed n-octadecylsiloxane self-assembled monolayers

In recent years a variety of techniques has appeared for the fabrication and manipulation of self-assembled monolayers (SAMs). This development now offers new tools for the study and control at the molecular level of the interaction of liquid crystals (LCs) with solid surfaces, a research area of great importance for liquid crystal applications. In this paper we show that mechanically rubbed octadecylsiloxane SAMs generate a novel surface alignment of LCs in which the in-plane surface anisotropy usually accompanying rubbing is operative, but only for smectics in which the mean molecular long axis, [ncirc], is tilted from the layer normal. On our SAMs smectic phases align with the layers parallel to the SAM surface, and in tilted smectics the surface component of [ncirc] is along the rubbing direction. This anisotropy is absent in the nematic phases which align with [ncirc] strictly normal to the surface. This behaviour can be understood in terms of a rubbed SAM monolayer surface, which is low energy, molecularly smooth, and rendered anisotropic by the rubbing. UV irradiation of rubbed SAMs gave excellent planar alignment ([ncirc] parallel to the surface). This type of control over LC alignment has not been previously reported.     

A study of the transition of liquid-crystal alignment from homeotropic to planar on a polyimide layer

The alignment of nematic liquid crystals by rubbed polyimide surfaces has been well-studied and developed. A novel polyimide film which induced a homeotropic alignment of the nematic liquid crystal without rubbing or with weak rubbing strength was presented. However, there was a transition from homeotropic to planar alignment of the nematic liquid crystal after strong rubbing. In order to study the transition, the polyimide surface was investigated by atomic force microscopy, surface free energy measurement and angle-resolved analysis X-ray photo-electron spectroscopy before and after rubbing with a velvet fabric. It was found that both the change of surface polarity and surface morphology were not the reasons for the transition. The droop of the side chain on the polyimide surface after the rubbing treatment was detected by angle-resolved analysis X-ray photo-electron spectroscopy. Owing to the special structure of the novel polyimide, the X-ray photo-electron spectroscopy was successfully used for the first time to analyse the conformational change of the side chain of a polymer. In conclusion, the transition of nematic liquid crystal alignment from homeotropic to planar after rubbing was influenced by the side chain conformation of the polyimide.     

Surface morphology at nanometer level and optical phase retardation of rubbed alignment films

The surface morphology of rubbed polyimide LC aligning films has been studied by scanning force microscopy. We examined three types of alignment film: HT-210, AL-1051 (main chain type) and AL-8044 (side chain type) polyimide surfaces. The rubbed polyimide surfaces show anisotropic alignment of the polymer chain cluster, and a microgroove between the ripple pattern streaks. Also, they are periodically oriented along the rubbing direction. The optical phase retardation of the rubbed surface does not increase with increased cumulative time of rubbing, On the other hand, it increases monotonically with increasing rubbing depth.     

Surface morphology at nanometer level and optical phase retardation of rubbed alignment films

The surface morphology of rubbed polyimide LC aligning films has been studied by scanning force microscopy. We examined three types of alignment film: HT-210, AL-1051 (main chain type) and AL-8044 (side chain type) polyimide surfaces. The rubbed polyimide surfaces show anisotropic alignment of the polymer chain cluster, and a microgroove between the ripple pattern streaks. Also, they are periodically oriented along the rubbing direction. The optical phase retardation of the rubbed surface does not increase with increased cumulative time of rubbing, On the other hand, it increases monotonically with increasing rubbing depth.     

Cell processing on polyimide surface patterned by rubbing

In this study, we prepared a novel rubbed fluorinated polyimide film using a rubbing machine with a rubbing cloth and determined the surface properties of the rubbed film using an atomic force microscope and contact angle measurements. In addition, we evaluated the cell adhesion behavior on the rubbed polyimide film using a phase contrast microscope. Interestingly, a rubbed polyimide surface having a micrometer‐scale grooved pattern was prepared by the rubbing method, and the morphologies of rat primary hepatocytes and human liver cell lines attached to the rubbed surface were three‐dimensional multicellular spheroids, while the cells on an unrubbed surface showed two‐dimensional monolayers. This initial study indicates that the rubbing method without any chemical modification is simple and can easily produce large surface areas, suggesting that the rubbing may become a novel cell culture method. Copyright © 2008 John Wiley & Sons, Ltd.     

Vertical alignment of liquid crystal on tocopherol-substituted polystyrene films

We synthesised a series of vitamin-based and renewable tocopherol-substituted polystyrene (PTOC#, # = 20, 40, 60, 80 and 100), where # is the molar content of tocopherol moiety, using polymer analogous reactions to investigate their liquid crystal (LC) alignment properties. In general, the LC cell fabricated using the polymer film having a higher molar content of tocopherol side group showed vertical LC alignment behaviour. The vertical alignment (VA) behaviour was well correlated with the surface energy value of these polymer films. For example, VA was observed when the surface energy values of the polymer were smaller than about 35.22 mJ/m² generated by the nonpolar tocopherol moiety having long and bulky carbon groups. Good electro-optical characteristics, such as voltage holding ratio and residual DC voltage, and aligning stabilities at 200°C and ultraviolet irradiation of 10 J/cm² were observed for the LC cells fabricated using PTOC100 as a LC alignment layer. Therefore, it was first found that the renewable tocopherol-based materials can produce an eco-friendly vertical LC alignment system.     

Langmuir–Blodgett films of stearic acid deposited on substrates at different orientations relative to compression direction: alignment layer for nematic liquid crystal

The Langmuir monolayer at an air–water interface shows remarkably different surface pressure (π)–area (A) isotherm, when measured with the surface normal of a Wilhelmy plate parallel or perpendicular to the direction of compression of the monolayer. Such difference arises due to difference in stress exerted by the monolayer on the plate in different direction. In this article, we report the effect of changing the direction of substrate normal with respect to the compression of the monolayer during Langmuir–Blodgett (LB) film deposition on the morphology of the films. The morphology of the LB film of stearic acid is studied using an atomic force microscope. The morphology of the LB films is found to be different due to difference in the stress in different directions. The role of such surface morphology on the alignment of a nematic liquid crystal (LC) in LC cells is studied. The granular texture of LB films of stearic acid supports the homogeneous alignment of the LC whereas the uniform texture supports the homeotropic alignment of the LC.     

Alignment of liquid crystals on ultrathin organized molecular films

Liquid crystal (LC) alignment techniques based on various kinds of ultrathin organized molecular films are reviewed. The mechanisms of LC alignment on the organized films are discussed. For the homeotropic alignment of LCs the main anchoring mechanism is due to the dipole–dipole interaction between polar groups of an aligning agent and LC molecules while the homogeneous alignment is mainly attributed to the orientation of polymer chains or polymer aggregates. An experimental system for an anchoring transition induced by a conformation change of aligning molecules is introduced. Finally the AFM experimental observations on the rubbed polymer films and its mechanisms are summarized.     

Novel polypyromellitimides and their liquid crystal aligning properties

Various aromatic poly{3,6‐bis[(4‐n‐alkyloxy)phenyloxy]‐pyromellitimide}s [poly(Ar‐C_m‐PMDA)s, m = 1, 4, 8, 12] were prepared in film form by routine two‐step condensation of 3,6‐bis[(4‐n‐alkyloxy)phenyloxy]pyromellitic dianhydrides (C_m‐PMDAs) with various aromatic diamines. After characterization of their chemical structures their solution, thermal and liquid crystal (LC)‐aligning properties in terms of pretilt angle at various rubbing densities were measured and discussed with respect to their backbone structures. All polyimide films showed excellent thermal stability and homogeneous LC alignment, but the poly(p‐phenylene‐C₁₂‐PMDA) exhibited completely homeotropic alignment while the pretilt angle values of poly(p‐phenylene‐C₈‐PMDA) varied with varying rubbing density.     

Investigation of surface anchoring strength and pretilt angle in NLC on rubbed polythiophene surfaces with alkyl chain lengths

A high pretilt angle for the nematic liquid crystal, 4-n-pentyl-4'-cyanobiphenyl (5CB), was observed on rubbed polythiophene (PTP) surfaces having alkyl chains with more than ten carbon atoms. We consider that this is due to a surface-excluded volume effect caused by the long alkyl chains between the LC molecules and the PTP surfaces. The polar anchoring strength in 5CB on rubbed PTP surfaces with long alkyl chains has also been successfully evaluated. The extrapolation length d_e of 5CB increases with increasing alkyl chain lengths above the seven carbons of alkyl chain R7; that is, it may be attributed to the high pretilt angle. An extrapolation length of 5 nm is observed in 5CB for the seven carbons alkyl chain R7 on the PTP surface; this indicates high anchoring strength.     

Influence of rubbing conditions of polyimide alignment layer on optical anisotropy of immobilized liquid crystal film

The relationship between the molecular orientation of a rubbed polyimide film (alignment layer) and that of mesogens in a photopolymerized liquid crystal (LC) coated on the film has been investigated using optical measurements. LC monomers were deposited on the alignment layer and were aligned in one direction. The LC monomers were subsequently photocured. Alignment layers under various rubbing conditions were prepared. It was found that the inclination angle of the refractive index ellipsoid and the optical retardation of photopolymerized LC films are strongly related to the optical anisotropy of the rubbed polyimide film. The photopolymerized LC film exhibited high optical anisotropy when alignment layers with an inclination angle of the refractive index ellipsoid smaller than 6° were used.     

Alignment of liquid crystals using Langmuir‒Blodgett films of unsymmetrical bent-core liquid crystals

ABSTRACT

The properties of the thin films of liquid crystal (LC) molecules can be governed easily by external fields. The anisotropic structure of the LC molecules has a large impact on the electrical and optical properties of the film. The Langmuir monolayer (LM) of LC molecules at the air–water interface is known to exhibit a variety of surface phases which can be transferred onto a solid substrate using the Langmuir?Blodgett (LB) technique. Here, we have studied the LM and LB films of asymmetrically substituted bent-core LC molecules. The morphology of LB film of the molecules is found to be a controlling parameter for aligning bulk LC in the nematic phase. It was found that the LB films of the bent-core molecules possessing defects favour the planar orientation of nematic LC, whereas the LB films with fewer defects show homeotropic alignment. The defect in LB films may introduce splay or bend distortions in the nematic near the alignment layer which can govern the planar alignment of the bulk LC. The uniform layer of LB film facilitates the molecules of nematic to anchor vertically due to a strong van der Waals interaction between the aliphatic chains leading to a homeotropic alignment.     

Washing effects on the anchoring energy and surface order parameter on rubbed polymer surfaces containing the trifluoromethyl moiety

The washing effects on liquid crystal (LC) alignment capability in a NLC, 4-n-pentyl-4'-cyanobiphenyl (5CB), on a rubbed polyimide (PI) surface containing the trifluoromethyl moiety were studied. The extrapolation length d_e of 5CB on the rubbed PI surface decreases with the rubbing strength RS. Also, the large extrapolation length d_e of 5CB for washing with IPA was measured at RS=114 mm. The polar anchoring energy of 5CB on the rubbed PI surface was decreased by the washing process; it increased with the rubbing strength RS on the PI surface. The surface order parameter S_S of 5CB for all the washing processes is smaller than for the non-washing process. Consequently, the polar anchoring energy and surface order parameter S_s in 5CB are largely attributed to washing effects.     

Liquid crystal alignment behaviours on poly(methyl methacrylate) having polyhedral oligomeric silsesquioxane groups

A series of poly(methyl methacrylate) derivatives containing polyhedral oligomeric silsesquioxane (POSS) groups (MCP#) were synthesised via free radical polymerisation (FRP) using methacryl isobutyl POSS (MA-POSS) and methyl methacrylate as monomers to investigate liquid crystal (LC) alignment property of these polymer films. The LC cells made from the films of the polymers having 100 mol% of MA-POSS units (MCP100) showed vertical LC alignment having a pretilt angle of about 90°. The vertical LC alignment behaviour on the MCP100 film was ascribed to the very hydrophobic MCP100 surface having the surface energy value smaller than about 23 mJ/m² generated by the nonpolar bulky POSS group. Good electro-optical characteristics, such as voltage holding ratio (VHR) and residual DC voltage (R-DC), were observed for the LC cells fabricated using MCP100 as a LC alignment layer.     

Oriented growth of crystalline pentacene films with preferred a-b in-plane alignment on a rubbed crystalline polymethylene surface

We have achieved a growth of highly oriented crystalline pentacene thin films, with preferred a-b in-plane orientation with respect to the rubbing direction of a rubbed polymethylene surface. The polymethylene thin film, generated on a gold surface by gold-catalyzed decomposition of diazomethane, was annealed and gently rubbed in a fixed direction by a flannelette cloth to serve as an alignment layer during the deposition of pentacene molecules. Various surface analysis techniques, including reflection absorption IR spectroscopy (RAIRS), near-edge X-ray absorption fine structure (NEXAFS) spectroscopy, grazing incidence X-ray diffraction (GIXD), and atomic force microscopy were used to elucidate the structural details of the polymethylene and the pentacene thin films deposited on it. Two crystalline morphologies of pentacene thin film were observed: the minor one of rod-like molecular crystals having their long axes of the crystals perpendicular to the rubbing direction, and the dominant one of platelet-like and layered crystals having the molecular axes stand near vertical to the surface. Moreover, GIXD revealed that the rubbing on polymethylene indeed induced a preferential azimuthal alignment of pentacene crystallites. The deposition of pentacene at 25 degrees C led to a twin growth of crystallites with the [110] direction predominately aligned perpendicular to the rubbing direction. In contrast, the pentacene deposition at 50 degrees C produced twinned crystallites of lower twin angle and the [120] direction aligned parallel to the rubbing direction.     

Patterned alignment of nematic liquid crystals generated by inkjet printing of gold nanoparticles and emissive carbon dots on both flexible polymer and rigid glass substrates

Patterned homeotropic alignment using nanoparticles (NPs) was achieved using inkjet printing. Two types of gold NPs, one smaller and one larger in core diameter (2 and 5 nm) capped with a monolayer of dodecanethiol, and emissive carbon dots with a core diameter of 2.5 nm featuring a mixed ligand shell of carboxylic acid groups and aliphatic hydrocarbon chains were tested on both rigid glass and flexible polycarbonate substrates. To define the director across the entire cell and not just in the NP-printed areas, alignment ‘underlayers’ were tested, and 30° obliquely evaporated SiO_x as alignment ‘underlayer’ generally provided the best results with the highest quality of the homeotropic alignment as well as the best contrast at the boundary between printed and non-printed (i.e. homeotropic and planar) domains of the fabricated cells. We also report that the chemical nature of the nematic liquid crystal (LC) used, the number of layers printed and the composition of the nano-ink need to be adjusted to obtain pattern alignment devices that positively benefit from both the properties of the LC and the nanomaterial printed.