Wettability,optical property of a superhydrophobic YAG film

A flame-like superhydrophobic yttrium aluminum garnet surface was obtained by a simple approach under ambient conditions. The influences of the concentration of curing agent and paraffin wax in course of the experiment were investigated. The as-prepared film shows superhydrophobicity which has a water contact angle of 158 ± 1.0°, and sliding angle of 4 ± 1.0°. Moreover, the water contact angle of the rough surface remained higher than 150°, after exposure for 10 days. Transmission electronic microscope, scanning electronic microscope, fluorescence spectrometer and atomic force microscope were also used to characterize the samples.     

Dielectric,optical and structural properties of Bi4V2−xSrxO11−δ (0.05≤x≤0.20)

Composition Bi₄V_2−xSr_xO_11−δ (0.05≤x≤0.20) is synthesized by melt quench technique followed by heat treatment at 800 °C for 12 h. These compounds are characterised by X-ray diffraction, Fourier transform infrared (FTIR) spectroscopy, UV–visible spectroscopy, impedance spectroscopy and scanning electron microscopy. X-ray diffraction patterns of all the samples show γ-phase stabilization at room temperature except x=0.05 heat treated sample. The optical band gap of all the samples is observed in semiconducting range. The lowest and the highest optical band gap is 2.39 eV and 2.57 eV for x=0.10 heat treated and x=0.20 quenched samples, respectively. The highest value of dielectric constant is obtained ~10⁷ with very low dielectric loss for x=0.15 and 0.20 samples at ~350 °C and below 10 Hz. The grain size increases with dopant concentration leads to increase the dielectric constant.     

Structural and optical properties of Mn-doped ZnO nanocrystalline thin films with the different dopant concentrations

The transparent nanocrystalline thin films of undoped zinc oxide and Mn-doped (Zn_1−xMn_xO) have been deposited on glass substrates via the sol–gel technique using zinc acetate dehydrate and manganese chloride as precursor. The as-deposited films with the different manganese compositions in the range of 2.5–20 at% were pre-heated at 100 °C for 1 h and 200 °C for 2 h, respectively, and then crystallized in air at 560 °C for 2 h. The structural properties and morphologies of the undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/Vis spectroscopy. The analyzed results indicates that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn related phases. Room temperature photoluminescence is observed for the ZnO and Mn-doped ZnO thin films.     

Influence of sintering conditions on the electrical properties of 10% ZrO2–10% Y2O3–CeO2 (mol%)

Yttria–zirconia doped ceria, 10% ZrO₂–10% Y₂O₃–CeO₂ (mol%) (CZY) and 0.5 mol% alumina-doped CZY (CZYA), prepared through oxide mixture process, were sintered by isothermal sintering (IS) and two-step sintering (TSS) having as variable the temperature and soaking time. The electrical conductivity of sintered samples was investigated in the 250 to 600 °C temperature range by impedance spectroscopy in air atmosphere. The microstructure was analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Alumina, as additive, improves the grain boundary conductivity of samples sintered at temperatures lower than 1500 °C. Concerning the sintering mode, two-step sintering (TSS) proved to be a good procedure to obtain CZYA samples with high electrical conductivity and density (> 95%) at relatively low sintering temperature and long soaking time.     

Understanding of redox behavior of Ni–YSZ cermets

The oxidation of Ni–YSZ cermet as well the reduction of re-oxidized Ni–YSZ cermet was investigated by using temperature-programmed oxidation (TPO), temperature-programmed reduction (TPR) and scanning electron microscope (SEM). The scanning electron microscope (SEM) photographs and temperature-programmed reduction (TPR) profiles indicated that the sintering of smaller nickel oxide crystallites to larger aggregates occurred concurrently with the formation of smaller nickel oxide crystallites from the oxidation of nickel at 800 °C, and the sintering of smaller nickel oxide crystallites at 600 °C was slower than that at 800 °C. The SEM results showed that each Ni particle was separated into a lot of smaller NiO particles during oxidation. The TPO profiles showed that two kinds of nickel particles exist in the anode reduced at 800 and 600 °C, one with high activity towards oxidation for the nickel crystallites directly from reduction, and another one with low activity towards oxidation for the sintered nickel particles. The Ni–YSZ anodes reduced at higher temperature showed higher re-oxidation temperature than the one reduced at lower temperature because of the accelerated passivating and sintering of the smaller nickel particles at higher temperature. The re-oxidation profiles were almost unchanged during redox cycling at 600 °C, whereas the re-oxidation peak temperature decreased during redox cycling at 800 °C, indicating that the primary nickel grains split to smaller ones upon cyclic reduction at higher temperature.     

Mixed oxygen ion and electron conducting hollow fiber membranes for oxygen separation

Phase inversion spinning technique was employed to prepare dense perovskite hollow fiber membranes made from composition BaCo_xFe_yZr_zO_3−δ (BCFZ, x + y + z = 1.0). Scanning electron microscope (SEM) shows that such hollow fibers have an asymmetric structure, which is favored to the oxygen permeation. An oxygen permeation flux of 7.6 cm³/min cm² at 900 °C under an oxygen gradient of 0.209 × 10⁵ Pa/0.065 × 10⁵ Pa was achieved. From the Wagner Theory, the oxygen permeation through the hollow fiber membrane is controlled by both bulk diffusion and surface exchange. The elements composition of fresh fiber and the fiber after long-term experiments were analyzed by energy-dispersive X-ray spectra (EDXS). Compared to the fresh fiber, sulphur was found on the tested hollow fiber membrane surface exposed to the air side and in the bulk, and Ba segregations occur on the tested hollow fiber membrane surface exposed to the air side. A decrease of the oxygen permeation flux was observed, which was probably due to the sulphur poisoning.     

Substrate bias effects during diamond like carbon film deposition by microwave ECR plasma CVD

Diamond like carbon (DLC) coatings were deposited on silicon(1 1 1) substrates by microwave electron cyclotron resonance (ECR) plasma CVD process using a plasma of Ar and CH₄ gases under the influence of DC self bias generated on the substrates by application of RF (13.56 MHz) power. DLC coatings were deposited under the varying influence of DC bias (−60 V to −150 V) on the Si substrates. Deposited films were analyzed by different techniques like: X-ray photoelectron spectroscopy (XPS), spectroscopic ellipsometry (SE), atomic force microscopy (AFM), Hardness and elastic modulus determination technique, Raman spectroscopy, scanning electron microscopy (SEM) and contact angle measurement. The results indicate that the film grown at −100 V bias has optimised properties like high sp³/sp² ratio of carbon bonding, high refractive index (2.26–2.17) over wide spectral range 400–1200 nm, low roughness of 0.8 nm, high contact angle (80°) compared to the films deposited at other bias voltages (−60 V and −150 V). The results are consistent with each other and find august explanation under the subplantation model for DLC growth.     

Growth and characterization of indium oxide films

In₂O₃ films have been deposited using chemical spray pyrolysis technique at different substrate temperatures that varied in the range, 250–450 °C. The structural and morphological properties of the as-deposited films were studied using X-ray diffractometer and scanning electron microscope as well as atomic force microscope, respectively. The films formed at a temperature of 400 °C showed body-centered cubic structure with a strong (2 2 2) orientation. The structural parameters such as the crystallite size, lattice strain and texture coefficient of the films were also calculated. The films deposited at a temperature of 400 °C showed an optical transmittance of >85% in the visible region. The change of resistivity, mobility, carrier concentration and activation energies with the deposition temperature was studied. The highest figure of merit for the layers grown at 400 °C was 1.09 × 10⁻³ Ω⁻¹.     

Influence of heat treatment on field emission characteristics of boron nitride thin films

Boron nitride (BN) nanometer thin films are synthesized on Si (1 0 0) substrates by RF reactive magnetron sputtering. Then the film surfaces are treated in the case of the base pressure below 5 × 10⁻⁴ Pa and the temperature of 800 and 1000 °C, respectively. And the films are studied by Fourier transform infrared spectra (FTIR), atomic force microscopic (AFM) and field emission characteristics at different annealing temperature. The results show that the surface heat treatment makes no apparent influence on the surface morphology of the BN films. The transformations of the sample emission characteristics have to do with the surface negative electron affinity (NEA) of the films possibly. The threshold electric fields are lower for BN samples without heat-treating than the treated films, which possibly ascribed to the surface negative electron affinity effect. A threshold field of 8 V/μm and the emission current of 80 μA are obtained. The surface NEA is still presence at the heat treatment temperature of 800 °C and disappeared at temperature of 1000 °C.     

Synthesis,characterization and photoluminescence of ZnO:Cd rosette-like nanostructures using solution process

Well crystalline undoped and Cd-doped ZnO rosette-like structures were successfully synthesized at low temperature (80 °C) via solution process technique during 30 min. Zinc nitrate, cadmium nitrate, sodium hydroxide and hexamine were used as starting materials. The morphology and microstructure were determined by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX) and photoluminescence (PL) spectroscopy. X-ray diffraction indicated that the structure has a single phase with wurtzite structure. FESEM indicated that rosette like structures have been formed. This rosette consists of nanorods with length 210 and 460 nm and diameter 50 and 74 nm for undoped and Cd doped ZnO, respectively. HRTEM showed a decrease in the lattice parameter after the Cd doping. EDX showed that the amount of Cd incorporated into ZnO is 6.4 wt.%. Photoluminescence measurements taken on both doped and undoped samples showed that, in the Cd-doped ZnO nanostructures, the band-edge UV emission is blue shifted and the broad green emission intensity decreased.     

Characterization of Laves phase in Crofer 22 H stainless steel

This study investigated the effect of annealing temperature on the precipitation behavior of Crofer^® 22 H at 600 °C, 700 °C, and 800 °C. The grain size distribution, precipitate phase identification, and microstructure were analyzed using electron backscatter diffraction (EBSD) and energy dispersive X-ray spectroscopy (EDS). The morphology of Laves phase (Fe,Cr,Si)₂(Nb,W) precipitates having the Cr₂Nb structure changed from strip-like to needle-shaped as the annealing temperature was increased. The precipitates of the Laves phase also shifted from the grain boundaries to the grain interiors when the temperature was increased. However, the average grain size (150 μm) of the ferritic matrix did not significantly change at 600 °C, 700 °C, and 800 °C for 10 h.     

Inelastic electron irradiation damage in hexagonal boron nitride

We present a study of the inelastic effects caused by electron irradiation in monolayer hexagonal boron nitride (h-BN). The data was obtained through in situ experiments performed inside a low-voltage aberration-corrected transmission electron microscope (TEM). By using various specialized sample holders, we study defect formation and evolution with sub-nanometer resolution over a wide range of temperatures, between −196 and 1200 °C, highlighting significant differences in the geometry of the structures that form. The data is then quantified, allowing insight into the defect formation mechanism, which is discussed in comparison with the potential candidate damage processes. We show that the defect shapes are determined by an interplay between electron damage, which we assign to charging, and thermal effects. We additionally show that this damage can be avoided altogether by overlapping the samples with a monolayer of graphene, confirming this for h-BN and providing a way to overcome the well-known fragility of h-BN under the electron beam.     

Controlled fabrication of Si nanostructures by high vacuum electron beam annealing

Silicon nanostructures, called Si nanowhiskers, have been successfully synthesized on Si(1 0 0) substrate by high vacuum electron beam annealing (EBA). Detailed analysis of the Si nanowhisker morphology depending on annealing temperature, duration and the temperature gradients applied in the annealing cycle is presented. A correlation was found between the variation in annealing temperature and the nanowhisker height and density. Annealing at 935 °C for 0 s, the density of nanowhiskers is about 0.2 μm⁻² with average height of 2.4 nm grow on a surface area of 5×5 μm, whereas more than 500 nanowhiskers (density up to 28 μm⁻²) with an important average height of 4.6 nm for field emission applications grow on the same surface area for a sample annealed at 970 °C for 0 s. At a cooling rate of −50 °C s⁻¹ during the annealing cycle, 10–12 nanowhiskers grew on a surface area of 5×5 μm, whereas close to 500 nanowhiskers grew on the same surface area for samples annealed at the cooling rate of −5 °C s⁻¹. An exponential dependence between the density of Si nanowhiskers and the cooling rate has been found. At 950 °C, the average height of Si nanowhiskers increased from 4.0 to 6.3 nm with an increase of annealing duration from 10 to 180 s. A linear dependence exists between the average height of Si nanowhiskers and annealing duration. Selected results are presented showing the possibility of controlling the density and the height of Si nanowhiskers for improved field emission properties by applying different annealing temperatures, durations and cooling rates.     

Thermal expansion behavior and chemical compatibility of BaxSr1−xCo1−yFeyO3−δ with 8YSZ and 20GDC

Perovskite oxides of the composition Ba_xSr_1−xCo_1−yFe_yO_3−δ(BSCF) were synthesized via a modified Pechini method and characterized by X-ray diffraction, dilatometry and thermogravimetry. Investigations revealed that single-phase perovskites with cubic structure can be obtained for x ≤ 0.6 and 0.2 ≤ y ≤ 1.0. The as-synthesized BSCF powders can be sintered in several hours to nearly full density at temperatures of over 1180 °C. Thermal expansion curves of dense BSCF samples show nonlinear behavior with sudden increase in thermal expansion rate between about 500 °C and 650 °C, due mainly to the loss of lattice oxygen caused by the reduction of Co⁴⁺ and Fe⁴⁺ to lower valence states. Thermal expansion coefficients (TECs) of BSCF were measured to be 19.2–22.9 × 10^− 6 K^− 1 between 25 °C and 850 °C. Investigations showed further that Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ is chemically compatible with 8YSZ and 20GDC for temperatures up to 800 °C, above which severe reactions were detected. After being heat-treated with 8YSZ or 20GDC for 5 h above 1000 °C, Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ was completely converted to phases like SrCoO_3−δ, BaCeO₃, BaZrO₃, etc.     

Effects of calcining temperature on structural and magnetic properties of nanosized Fe-doped NiO prepared by diol-based sol−gel process

Iron-doped nickel oxide (Fe_0.01Ni_0.99O, abbreviated as FNO) nanoparticles were prepared by sol–gel process using 1,3-propanediol as a solvent and also as a chelating agent, and calcined at the various temperatures (400–1000 °C) for 2 h. The phase composition and the microstructure of the calcined products were investigated by X-ray diffraction and scanning electron microscopy techniques, respectively. Magnetic properties were measured at room temperature using a vibrating sample magnetometer. All calcined samples showed the single phase of FNO cubic rock-salt structure without the presence of any impurity phases. The crystallite size from XRD and particle size from SEM increased as calcining temperature increased. The FNO powders calcined at 400?600 °C revealed the uniform and dense spherical particles in nanosize. The room-temperature ferromagnetism was observed for all samples. When the calcining temperature was increased, the saturation magnetization decreased whereas the coercivity increased, corresponding to the less dense and larger particles. The calcined sample at 400 °C had the best magnetic properties with the highest M_s of 5.34 emu/g (at 10 kOe) and the lowest H_c of 372 Oe.     

Comparative PEEM and AES study of surface morphology and composition of Cu films on Si and 3C–SiC substrates

We have conducted photoemission electron microscope (PEEM) and Auger electron spectroscopy (AES) studies on the Cu(30 nm)/3C–SiC(1 0 0) and Cu(30 nm)/Si(1 0 0) samples annealed successively up to 850 °C. With PEEM, lateral diffusion of Cu atoms on the 3C–SiC substrate was observed at 400 °C while no lateral diffusion was seen for the Cu/Si(1 0 0) samples up to 850 °C. The 30 nm Cu thin film on 3C–SiC began to agglomerate at 550 °C, similar to the case for the Cu/Si(1 0 0) system. No further spread of the lateral diffusion region was found in subsequent annealing up to 850 °C for Cu/3C–SiC while separated regular-sized dot structures were found at 850 °C for Cu/Si(1 0 0). AES studies of Cu/Si(1 0 0) system showed partial interface reaction during Cu deposition onto the Si(1 0 0) substrate and oxidation of the resultant Cu₃Si to form SiO₂ on the specimen surface at room temperature in air. Surface segregation of Si and C was observed after annealing at 300 °C for Cu/Si(1 0 0) and at 850 °C for the Cu/3C–SiC system. We have successfully elucidated the observed phenomena by combining PEEM and AES considering diffusion of the constituent elements and/or reaction at interfaces.     

Effect of growth time of hydrothermally grown cobalt hydroxide carbonate on its supercapacitive performance

We present the time-dependent synthesis of cobalt hydroxide carbonate nanorods by hydrothermal method with a systematic increase of different parameters such as specific surface area and specific capacitance as a function of different synthesis time. Morphological characterization of the cobalt hydroxide carbonate nanorods were carried out by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that variation of the time of reaction plays a crucial role in the transformation of samples’ morphology. Cobalt hydroxide carbonate nanorods synthesized with 12 h reaction time, which is the reaction just before the materials transforms into cobalt oxide under the same synthesis conditions exhibited the highest specific capacitance of 466 F g⁻¹ at a current density of 1 A g⁻¹ in 6 M KOH electrolyte and also showed excellent stability with ∼99% capacitance retention after 2000 cycles at a current density of 10 A g⁻¹. Based on the above results, the cobalt hydroxide carbonate nanorods show a considerable potential as electrodes materials for supercapacitor applications.     

Thermal and sonochemical synthesis of porous (Ce,Zr)O2 mixed oxides from metal β-diketonate precursors and their catalytic activity in wet air oxidation process of formic acid

Porous (Ce_0.5Zr_0.5)O₂ solid solutions were prepared by thermolysis (T = 285 °C) or sonolysis (20 kHz, I = 32 W cm⁻², P_ac = 0.46 W mL⁻¹, T = 200 °C) of Ce(III) and Zr(IV) acetylacetonates in oleylamine or hexadecylamine under argon followed by heat treatment of the precipitates obtained in air at 450 °C. Transmission Electron Microscopy images of the samples show nanoparticles of ca. 4–6 nm for the two synthetic approaches. The powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray and μ-Raman spectroscopy of solids obtained after heat treatment indicate the formation of (Ce_0.5Zr_0.5)O₂ solid solutions with a metastable tetragonal crystal structure for the two synthetic routes. The specific surface area of the samples varies between 78 and 149 m² g⁻¹ depending on synthesis conditions. The use of Barrett–Joyner–Halenda and t-plot methods reveal the formation of mixed oxides with a hybrid morphology that combines mesoporosity and microporosity regardless of the method of preparation. Platinum nanoparticles were deposited on the surface of the mixed oxides by sonochemical reduction of Pt(IV). It was found that the materials prepared by sonochemistry exhibit better resistance to dissolution during the deposition process of platinum. X-ray photoelectron spectroscopy analysis shows the presence of Pt(0) and Pt(II) on the surface of mixed oxides. Porous (Ce_0.5Zr_0.5)O₂ mixed oxides loaded with 1.5 %wt. platinum exhibit high activity in catalytic wet air oxidation of formic acid at 40 °C.     

Nanostructure materials for destruction of warfare agents and eco-toxins prepared by homogeneous hydrolysis with thioacetamide: Part 1—zinc oxide

Zinc sulphide (ZnS) nanoparticles were prepared by homogeneous hydrolysis of zinc sulphate and thioacetamide (TAA) at 80 °C. After annealing at temperature above 400 °C in oxygen atmosphere, zinc oxide (ZnO) nanoparticles were obtained. The ZnS and ZnO nanoparticles were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission microscopy (HRTEM), selected area electron diffraction (SAED), by BET and BJH methods used for surface area and porosity determination. The photocatalytic activity of the as-prepared ZnO samples was determined by the decomposition of Orange II in the aqueous solution under UV irradiation of 365 nm of wavelength.     

Impact of applied ultrasonic power on the low temperature drying of apple

Low temperature drying (LTD) allows high-quality dried products to be obtained, preserving the nutritional properties of fresh foods better than conventional drying, but it is a time-consuming operation. Power ultrasound (US) could be used to intensify LTD, but it should be taken into account that process variables, such as the level of applied power, have an influence on the magnitude and extension of the ultrasonic effects. Therefore, the aim of this work was to assess the influence of the level of applied ultrasonic power on the LTD of apple, analyzing the drying kinetics and the quality of the dried product. For that purpose, apple (Malus domestica cv. Granny Smith) cubes (8.8 mm side) were dried (2 m/s) at two different temperatures (10 and −10 °C), without and with (25, 50 and 75 W) US application. In the dried apple, the rehydration kinetics, hardness, total phenolic content, antioxidant capacity and microstructure were analyzed to evaluate the impact of the level of applied ultrasonic power.At both temperatures, 10 and −10 °C, the higher the ultrasonic power level, the shorter the drying time; the maximum shortening of the drying time achieved was 80.3% (at −10 °C and 75 W). The ultrasonic power level did not significantly (p < 0.05) affect the quality parameters analyzed. Therefore, US could be considered a non-thermal method of intensifying the LTD of fruits, like apple, with only a mild impact on the quality of the dried product.