Analysis of some chlorophenoxy acids and carbamate herbicides in water and soil as amide derivatives using gas chromatography-mass spectrometry

A newly developed method for determining three phenoxy acids and one carbamate herbicide in water and soil samples using gas chromatography with mass spectrometric detection is developed. Phenoxy acids are derivatized through a condensation reaction with a suitable aromatic amine. 1,1-Carbonyldiimidazole is used as a condensation reagent. Derivatization conditions are optimized with respect to the amount of analyte, amine, solvent, and derivatization reagent. The optimum derivatization yield is accomplished in acetonitrile. 4-Methoxy aniline is used as a derivatizing agent. Obtained derivatives are stable indefinitely. Enhancement in sensitivity is achieved by using the single-ion monitoring mass spectrometric mode. The effectiveness of the developed method is tested by determining investigated compounds in water and soil samples. Analytes are concentrated from water samples using liquid-phase extraction and solid-phase extraction. Soil samples are extracted using methanol. Detection limits of 1.00, 50.00, 100.00, and 1.00 ng/mL are obtained for 2-(1-methylethoxy)phenyl methylcarbamate (Baygon), 2-(3-chlorophenoxy)-propionic acid (Cloprop), 2,4,5-trichlorophenoxyacetic acid, and 4-(2,4-dichlorophenoxy)butyric acid, respectively. LPE for spiked water samples yields recoveries in the range of 60.6-95.7%, with relative standard deviation (RSD) values of 1.07-7.85% using single component calibration curves. Recoveries of 44.8-275.5%, with RSD values ranging from 1.43% to 8.61% were obtained using a mixed component calibration curves. SPE from water samples and soil samples showed low recoveries. The reason is attributed to the weak sorption capabilities of soil and Al(2)O(3).     

Solid-phase extraction of acidic herbicides

A discussion of solid-phase extraction method development for acidic herbicides is presented that reviews sample matrix modification, extraction sorbent selection, derivatization procedures for gas chromatographic analysis, and clean-up procedures for high-performance liquid chromatographic analysis. Acidic herbicides are families of compounds that include derivatives of phenol (dinoseb, dinoterb and pentachlorophenol), benzoic acid (acifluorfen, chloramben, dicamba, 3,5-dichlorobenzoic acid and dacthal--a dibenzoic acid derivative), acetic acid [2,4-dichlorophenoxyacetic acid (2,4-D), 4-chloro-2-methylphenoxyacetic acid (MCPA) and 2,4,5-trichlorophenoxyacetic acid (2,4,5-T)], propanoic acid [dichlorprop, fluazifop, haloxyfop, 2-(4-chloro-2-methylphenoxy)propanoic acid (MCPP) and silvex], butanoic acid [4-(2,4-dichlorophenoxy)butanoic acid (2,4-DB) and 4-(4-chloro-2-methylphenoxy)butanoic acid (MCPB)], and other miscellaneous acids such as pyridinecarboxylic acid (picloram) and thiadiazine dioxide (bentazon).     

Chemically modified polymeric sorbents for sample preconcentration

Solid-phase extraction is an attractive alternative in sample preparation because it overcomes many drawbacks of liquid-liquid extraction and makes on-line determination possible by hyphenation with chromatographic techniques. Driven by the need for more effective and more selective sorbents, advances in solid-phase extraction include the development of new materials. This paper describes different types of chemically modified sorbents for the solid-phase extraction of compounds from aqueous samples. Chemical introduction of different functional groups into a polymeric resin improves the efficiency of solid-phase extraction by providing better surface contact with the aqueous samples; also, these sorbents have a greater capacity than the typical solid-phase materials for polar compounds have. The most important new sorbents are the chemically modified resins based on styrene-divinylbenzene copolymers. Preparation of these new sorbents is described, and advantages and drawbacks of off-line procedures and on-line procedures are also discussed. Applications for off-line and on-line chromatographic determinations of polar compounds are presented.     

Molecularly imprinted solid-phase extraction sorbent for the clean-up of chlorinated phenoxyacids from aqueous samples.

A molecularly imprinted polymer (MIP) was synthesized using the herbicide 2,4,5-trichlorophenoxyacetic acid as a template, 4-vinylpyridine as an interacting monomer, ethylendimethacrylate as a cross-linker and a methanol-water mixture as a porogen. The binding properties and the selectivity of the polymer towards the template were investigated by frontal and zonal liquid chromatography. The polymer was used as a solid-phase extraction material for the clean-up of the template molecule and some related herbicides (2,4-dichlorophenoxyacetic acid, fenoprop, dichlorprop) from river water samples at a concentration level of ng/ml with quantitative recoveries comparable with those obtained with a traditional C18 reversed-phase column when analyzed by capillary electrophoresis. The results obtained show that the MIP-based approach to the solid-phase extraction is comparable with the more traditional solid-phase extraction with C18 reversed-phase columns in terms of recovery, but it is superior in terms of sample clean-up.     

Solid-phase analytical derivatization: enhancement of sensitivity and selectivity of analysis.

Analytical derivatizations enhance the sensitivity and selectivity of determinations for organic compounds. Classical techniques are often based on solution chemistry. Most modern sample preparation techniques, however, are based on solid-phase extractions. Solid-phase analytical derivatization bridges this gap and facilitates sample preparation by combining the isolation step with the derivatization. The solid-phase retains both reagents and derivatized analytes and often permits facile separation of excess reagent or selective elution of the desired products. The most recent solid-phase extraction techniques have been used in conjunction with analytical derivatization to automate the analysis. In this review, analytical derivatizations are presented as functional group analysis.     

Optimization of solid-phase microextraction conditions for the determination of triclosan and possible related compounds in water samples

A solid-phase microextraction (SPME) method for the determination of triclosan, methyl triclosan, 2,4-dichlorophenol and 2,3,4-trichlorophenol (considered as possible triclosan metabolites) in water samples was optimised. Analytes were first concentrated on a SPME fibre, directly exposed to the sample, and then triclosan and the two chlorinated phenols on-fibre silylated using N-methyl-N-(tert.-butyldimethylsilyl)-trifluoroacetamide (MTBSTFA). Methyl triclosan remained unaffected during the derivatization step. Compounds were determined using gas chromatography in combination with mass spectrometry (GC-MS). Influence of different factors on the efficiency of extraction and derivatization steps was systematically investigated. Using a polyacrylate (PA) fibre quantification limits below 10 ng/l, and acceptable relative standard deviations, were obtained for all compounds after an extraction time of 30 min. On-fibre silylation was carried out in only 10 min. Moreover, the efficiency of the procedure was scarcely affected by the type of water sample. The method was applied to several samples of treated and raw wastewater, triclosan was found in all samples, at concentrations from 120 to 14,000 ng/l, and 2,4-dichlorophenol in most of them, at levels up to 2222 ng/l.     

Analysis of Seven Herbicides by Gas-Liquid Chromatography

Simutaneous analysis of seven commonly used herbicides, 2,4-D methyl ester, 2,4-D methyl ester, 2,4,5-T methyl ester, silvex methyl ester, ramrod, CIPC and DEF, by gas-liquid chromatography with an electron capture detector was attempted. Two packed columns (which are generally used for the analysis of chlorinated pesticides) and two chemically bonded fused silica capillary columns were used for the analysis. When the packed columns were used, ramrod always interfered with the analysis of 2,4-D methyl ester and/or silvex methyl ester. Complete separation with reasonable analysis time can be achieved using one of the chemically bonded fused silica capillary columns.     

Microwave and ultrasonic extraction of chlorophenoxy acids from soil and their determination by fluorescence polarization immunoassay

Procedures were developed for the ultrasonic and microwave extraction of pesticides, 2,4-dichlorophenoxyacetic (2,4-D) and 2,4,5-trichlophenoxyacetic (2,4,5-T) acids from soils for the subsequent determination by fluorescence polarization immunoassay (FPIA). The effect of the matrix composition of soils on the FPIA results was studied, and the optimum extractants and extraction conditions were selected. It was found that 40% ethanol is optimum for both extraction and FPIA determination, because it does not cause antibody denaturation. The recovery of pesticides in soil was 80–132% for 2,4-D and 101–138% for 2,4,5-T. Microwave extraction is more efficient than ultrasonic extraction for the determination of 2,4-D and 2,4,5-T in soil. The detection limit in soil and the analytical range are 2 and 4–200 μg/g, respectively, for 2,4-D and 20 and 80–5000 μg/g, respectively, for 2,4,5-T. Results of the determination of 2,4-D in soil by FPIA are in good agreement with the results of the determination by high-performance liquid chromatography. The procedures can be used for the rapid determination of chlorophenoxy acids in soils.     

Development of an impregnated reagent and automation of solid-phase analytical derivatization for carbonyls: proof of principle

This study undertakes reduction of scale and automation of a solid-phase analytical derivatization of carbonyls with 2,4-dinitrophenylhyrazine on a styrene-divinylbenzene resin (XAD-2). Three processes are tested. In the batch process, an aqueous phase consisting of 50 microL of sample and 150 microL of reagent solution is contacted with 6 mg XAD-2 by shaking. An impregnated reagent consisting of 2,4-dinitrophenylhydrazine hydrochloride (DNPH) deposited on XAD-2 enables two additional processes. In-vial derivatization with an impregnated reagent requires shaking 50 microL of sample with 6 mg of the impregnated reagent and reduced the reaction time from 10 to 5 min. The third process involves packing impregnated reagent a mini-column and flowing 50 microL of sample through under positive pressure supplied by a Harvard Pump. This reduces sample preparation time to 1 min. Studies are conducted with worst-case model analytes: butanone, 2-pentanone, and malonyldialdehyde. The carbonyl of the two ketones is hindered, and, thus, these two compounds react very slowly with DNPH in aqueous solution. Malonyldialdehyde is highly water soluble, and it does not react in aqueous phase but also would not sorb onto XAD-2 for reaction. Nevertheless, derivatization/extraction of all model compounds any of the three procedures result in reproducible and high yields.     

Construction,Expression, and Characterization of a Single-Chain Variable Fragment Antibody Against 2,4-Dichlorophenoxyacetic Acid in the Hemolymph of Silkworm Larvae

A single-chain variable fragment antibody against herbicide, 2,4-dichlorophenoxyacetic acid (2,4-D-scFv) has been successfully expressed in the hemolymph of silkworm larvae using a rapid Bombyx mori nucleopolyhedrovirus (BmNPV) bacmid DNA system. Variable heavy- and light-chain domains were cloned directly from the cDNA of the hybridoma cell line 2C4 and assembled together with flexible peptide linker (Gly₄Ser)₃ between two domains. The yield of functional 2,4-D-scFv after purification was 640 μg per 30 ml of hemolymph, which is equivalent to 21.3 mg per liter of hemolymph. The characterization of 2,4-D-scFv using an indirect competitive enzyme-linked immunosorbent assay (icELISA) revealed that it has wide cross-reactivities against 2,4,5-trichlorophenoxyacetic acid (65.5%), 2,4-dichlorophenol (47.9%), and 2,4-dichlorobenzoic acid (26.0%), making it possible to apply 2,4-D-scFv to icELISA for detecting/determining 2,4-D and its metabolites. Judging from its cost and time requirements and its ease of handling, this BmNPV bacmid DNA expression system is more useful for expressing functional scFv than bacterial systems, which frequently require costly and time-consuming refolding.     

Determination of acidic herbicides in surface water by solid-phase extraction followed by capillary zone electrophoresis

A rapid solid-phase extraction-capillary zone electrophoresis (CZE) method for determining 2,4-dichlorophenoxyacetic acid, 4-(2,4-dichlorophenoxy) butyric acid, and 2,4,5-trichlorophenoxyacetic acid in real water samples is described. Factors affecting the recoveries and detection of the targets are investigated. With samples being acidified to pH 2 and salted by sodium sulfate to 2% (w/w), an average recovery of greater than 85% is obtained using ethyl acetate as the eluent on an octadecylsilane-bonded silica cartridge. A running buffer of 5 mM sodium tetraborate in a water-acetonitrile mixture (70:30, v/v) adjusted to pH 9 is employed in the CZE analysis, and the targets can be analyzed within 7 min with good reproducibility and acceptable sensitivity. The method is suitable for detecting herbicide residues of sub-parts-per-billion levels in surface water. A local pond water is analyzed, and the concentrations of 2,4-dichlorophenoxyacetic acid and 4-(2,4-dichlorophenoxy) butyric acid are detected to be 0.27 +/- 0.03 ppb and 0.61 +/- 0.08 ppb, respectively.     

On-line continuous-flow extraction system in liqud chromatography with ultraviolet and mass spectrometric detection for the determination of selected organic pollutants

An on-line extraction system with completely continuous-flow analysis prior to the liquid chromatographic (LC) column was used for the determination of the organophosphorus pesticides tetrachlorvinphos and parathion-methyl and their degradation products 2,4,5-trichlorophenol and 4-nitrophenol, respectively, and the chlorinated phenoxy acids 2,4-D, 2,4,5-T and silvex in water samples. The extent of extraction varied from 100% for chlorinated phenoxy acids to 60% for organophosphorus pesticides and 2,4,5-trichlorophenol. The extraction of 4-nitrophenol was less than 10% under these conditions. By employing positive-ion mode thermospray LC-mass spectrometry, the characterization of tetrachlorvinphos was feasible, indicating [M + NH₄]⁺ as the base peak and a second peak with 20% relative intensity corresponding to [M + H]⁺. When the negative-ion mode was used, the chlorinated phenoxy acids and 2,4,5-trichlorophenol exhibited [M + HCOO]^? as the base peak and a second peak with 30% relative intensity corresponding to [M ? H]^?. The determination of 1 mg l^?1 of tetrachlorvinphos spiked in a surface water sample is reported.     

Analysis of Hexanal and Heptanal in Human Blood by Simultaneous Derivatization and Dispersive Liquid–Liquid Microextraction then LC–APCI–MS–MS

A new analytical approach, simultaneous derivatization and dispersive liquid–liquid microextraction followed by liquid chromatography–atmospheric-pressure chemical ionization tandem mass spectrometry, has been developed for analysis of hexanal and heptanal in human blood. In the derivatization and extraction procedure a solution of 2,4-dinitrophenylhydrazine (derivatization reagent) in 85 μL acetonitrile (dispersive solvent) and 50 μL tetrachloromethane (extraction solvent) was rapidly injected into the aqueous sample containing hexanal and heptanal. Within a few seconds the aldehydes were derivatized and simultaneously extracted. After centrifugation, the hydrazones in the sediment phase were analyzed by LC–APCI–MS–MS. Derivatization and extraction conditions were investigated systematically. Under the optimum conditions enrichment factors for hexanal and heptanal in a 1-mL sample were 63 and 73, respectively. The calibration plots were linear in the ranges 0.5–100 and 100–1,000 nmol L^?1, respectively, and the respective limits of detection (LOD) were 0.17 and 0.076 nmol L^?1. Reproducibility and recovery were good. The experimental results were compared with those obtained by use of solid-phase extraction and polymer monolithic microextraction. Because sample derivatization, extraction, and concentration were combined in a single step, the proposed method enabled simple, rapid, inexpensive, and efficient analysis of aldehydes in blood. The method has great potential for clinical analysis of biologically relevant aldehydes.     

Extraction of alkyl methylphosphonic acids from aqueous samples using a conventional polymeric solid-phase extraction sorbent and a molecularly imprinted polymer

The analysis of alkyl methylphosphonic acids (AMPAs) constitutes an important subject for verifying the compliance to the Chemical Weapons Convention (CWC). Indeed, alkyl methylphosphonic acids are the degradation products of V and G nerve agents such as VX, sarin or soman. Lowering the limits of detection of analytical methods for complex aqueous matrices implies the introduction of concentration and clean-up steps in the whole analytical process. Therefore a molecular imprinted polymer (MIP) has been previously developed for the selective extraction and the concentration of the alkyl methylphosphonic acids. Unfortunately, the selective retention process on this MIP has involved the development of hydrogen bonds and so does not allow the direct percolation of aqueous samples. A change of solvent is then necessary and can be performed using solid-phase extraction (SPE) with conventional non selective hydrophobic sorbents. Two polymeric sorbents, Oasis HLB and HR-P resins, were selected for their high specific surface area. The extraction recoveries obtained on both sorbents were compared and the Oasis HLB sorbent was further selected and used for the percolation of acidified aqueous samples. An optimised SPE procedure was then applied to concentrate an aqueous soil extract spiked with isobutyl methylphosphonic acid (iBMPA) and cyclopentyl methylphosphonic acid (cPMPA) that was further cleaned-up by passing through the MIP. The resulting LC-MS full scan chromatograms highlight the clean-up effect of the SPE-MIP association by the removal of the matrix substances and the preservation of 95% of the compounds of interest.     

气相色谱–质谱法测定棉花中苯氧羧酸类除草剂

采用气相色谱–质谱联用法检测棉花中3种苯氧羧酸类除草剂[2,4-D,2,4,5-T,2-甲-4-氯丁酸(MCPB)]的残留量。样品用甲酸酸化的丙酮提取,硫酸催化甲酯化反应,用气相色谱–质谱联用仪测定。采用HPLC法与GC–MS法对提取与衍生化步骤进行优化。2,4-D,2,4,5-T,MCPB 3种化合物在0.075~7.5 mg/kg范围内线性均良好,检出限分别为0.5,0.5,0.8μg/kg,测定结果的相对标准偏差分别为4.1%,4.3%,4.0%(n=5),方法回收率分别为93.6%,95.5%,93.9%。该方法各项指标均可满足检测要求。     

Optimizing Separation Conditions for Chlorophenoxycarboxylic Acid Herbicides in Natural and Potable Water Using Capillary Zone Electrophoresis

Chlorophenoxycarboxylic acid herbicides were separated and determined by capillary electrophoresis. An analysis of a six-component mixture containing 2,4-dichlorophenoxybutyric (2,4-DB), 2,4-dichlorophenoxypropionic (2,4-DP), 2,4,5-trichlorophenoxyacetic (2,4,5-T), 2,4-dichlorophenoxyacetic (2,4-D), and phenoxyacetic (PA) acids and 2,4-dichlorophenol (2,4-DCP), the product of their degradation in aqueous media, took no longer than 15 min. Solid-phase extraction on Diapak C-16 cartridges was used for sample preparation. The detection limits for herbicides in water samples with account for preconcentration (K = 250) were found to be 0.0005 mg/L for 2,4-DB, 2,4-DP, 2,4,5-T, and 2,4-D and 0.001 mg/L for PA. It was shown that humic acids (< 50 mg/L) do not interfere with the determination of chlorophenoxycarboxylic acids.     

Optimization of headspace experimental factors to determine chlorophenols in water by means of headspace solid-phase microextraction and gas chromatography coupled with mass spectrometry and parallel factor analysis

In this work an analytical procedure based on headspace solid-phase microextraction and gas chromatography coupled with mass spectrometry (HS-SPME–GC/MS) is proposed to determine chlorophenols with prior derivatization step to improve analyte volatility and therefore the decision limit (CCα). After optimization, the analytical procedure was applied to analyze river water samples. The following analytes are studied: 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TrCP), 2,3,4,6-tetrachlorophenol (2,4,6-TeCP) and pentachlorophenol (PCP). A D-optimal design is used to study the parameters affecting the HS-SPME process and the derivatization step. Four experimental factors at two levels and one factor at three levels were considered: (i) equilibrium/extraction temperature, (ii) extraction time, (iii) sample volume, (iv) agitation time and (v) equilibrium time. In addition two interactions between four of them were considered. The D-optimal design enables the reduction of the number of experiments from 48 to 18 while maintaining enough precision in the estimation of the effects. As every analysis took 1 h, the design is blocked in 2 days.     

固相萃取-衍生化-气相色谱法测定血液中的3种苯氧羧酸类除草剂

建立了一种血液中2,4-二氯苯氧乙酸(2,4-D)、2-(2,4-二氯苯氧)-丙酸(2,4-DP)和4-氯-2-甲基-苯氧乙酸(MCPA)3种苯氧羧酸类除草剂的分析方法.血样用0.1 mol/L盐酸稀释后用GDX401大孔树脂吸附、用乙醚洗脱,萃取物用二氯丙醇在硫酸催化下进行酯化衍生,衍生物经气相色谱-电子捕获检测.2,4-D、2,4-DP和MCPA的检测限分别为20,8和40 ng/mL.定量分析用2,4-二氯苯乙酸作内标,线性关系和回收率结果均令人满意.     

Composite carbon-fluoroplastic surface-layer sorbents for the rapid preconcentration of organic substances from aqueous solutions

The regularities of the dynamic solid-phase extraction of organic substances (exemplified by chloroform, butyl acetate, and diethyl ether) from aqueous solutions on composite surface-layer sorbents, in which a finely dispersed sorption-active carbon material (active carbon or nanocarbon) was supported onto the surface of porous polytetrafluoroethylene, were found. It was demonstrated that the efficiency of the sorbents developed was higher than that of traditional bulk porous sorbents used for the preconcentration of volatile organic substances from aqueous solutions.     

Selective removal of chlorine from chloroaromatic pollutants by electrocatalytic reduction over palladium-loaded carbon felt

This brief review outlines work on effective hydrodechlorination of environmentally persistent chlorine-containing aromatic pollutants by electrocatalytic reduction at Pd-loaded carbon felt. The selective removal of chlorine from phenoxy herbicides 2,4-D and 2,4,5-T, chlorinated biphenyls and naphthalene was readily achieved (i) at room temperature and (ii) directly in aqueous media. No highly active reducing chemicals were required for such a treatment. The use of carbon felt of high surface area as a solution-permeable cathode offered high adsorption capacity for chloroaromatics, while supported palladium provided the system with a highly reactive reducing species supposed to be a surface-bound hydride, which was generated upon electrochemical reductive decomposition of water. A facilitating effect of bulky tetraalkylammonium cations of a supporting electrolyte on substrate conversion and product recovery is considered. The reaction mechanism for selective hydrodechlorination of chloroaromatics in aqueous media and scheme for activation of Pd-loaded carbon felt by electrolytic pre-treatment are proposed and discussed.