Spinel LiMn2O4 active material with high capacity retention

Heating the mixture of LiMn₂O₄ and NiO at 650 °C was employed to enhance the cyclability of spinel LiMn₂O₄. The results of scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) spectroscopy analyses implied that a LiNi_xMn_2−xO₄ solid solution was formed on the surface of LiMn₂O₄ particles. And charge-discharge tests showed that the enhancement of the capacity retention of modified LiMn₂O₄ is significant, maintained 97.2% of the maximum capacity after 100 cycles at charge and discharge rate of C/2, while the pure one only 75.2%. The modified LiMn₂O₄ also results in a distinct improvement in rate capability, even at the rate of 12C. The improvement of electrochemical cycling stability is greatly attributed to the suppression of Jahn-Teller distortion at the surface of spinel LiMn₂O₄ particles.     

Atomic force microscopy study of surface morphology change in spinel LiMn2O4: Possibility of direct observation of Jahn-Teller instability

Surface morphology in 3.5 × 3.5 μm² area of spinel LiMn₂O₄, which is a typical cathode material for Li ion secondary batteries, is studied using an atomic force microscopy (AFM) with a conductive probe. Negative bias voltage is applied to the probe to attract Li⁺ ions toward LiMn₂O₄ surface during the AFM observation. Before applying the voltage (0 V), the whole LiMn₂O₄ surface is covered with scale-shaped grains. Under the negative voltage of 5.5 V, electric current abruptly increases, indicating Li⁺ ionic conduction. Simultaneously, part of the scale-shaped grains expand and flatten. Jahn-Teller phase transition, which is induced by the repulsive interaction between the Mn-e_g and O-2p electrons in Li accumulated layer, is proposed as a possible origin of these results.     

Novel approach to preparation of LiMn2O4 core/LiNixMn2−xO4 shell composite

Combining two methods, coating and doping, to modify spinel LiMn₂O₄, is a novel approach we used to synthesize active material. First we coated the LiMn₂O₄ particles with the nickel oxide particles by means of homogenous precipitation, and then the nickel oxide-coated LiMn₂O₄ was calcined at 750 °C to form a LiNi_xMn_2−xO₄ shell on the surface of spinel LiMn₂O₄ particles. Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), cyclic voltammetry (CV) and charge-discharge test were performed to characterize the spinel LiMn₂O₄ before and after modification. The experimental results indicated that a spinel LiMn₂O₄ core is surrounded by a LiNi_xMn_2−xO₄ shell. The resulting composite showed excellent electrochemical cycling performance with an average fading rate of 0.014% per cycle. This improved cycle stability is greatly attributed to the suppression of Jahn-Teller distortion on the surface of spinel LiMn₂O₄ particles during cycling.     

Effect of ultrasonic irradiation on structure and electrochemical properties of LiMn2O4 thin films cathode material for Li-ion micro-batteries

Two kinds of spinel LiMn₂O₄ thin film for lithium ion micro-batteries were successfully prepared on polycrystal Pt substrates by spin coating methods, which were carried out under ultrasonic irradiation (USG) and magnetic stirring (MSG), respectively. The microstructures and electrochemical performance of LiMn₂O₄ thin films were characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and galvanostatic charge-discharge measurements. It was found that the crystalline structure of USG samples grew better than that of the MSG samples. At the same time, higher discharge capacity and better cycle stability were obtained for the LiMn₂O₄ thin films of USG at the current density of 50 μAh/cm² between 3.0 and 4.3 V. The 1st discharge capacity was 57.8 μAh/cm²-μm for USG thin films and 51.7 μAh/cm²-μm for MSG thin films. After 50 cycles, 91.4% and 69% of discharge capacity could be retained respectively, indicating that ultrasonic irradiation condition during spin coating was more suitable for preparing spinel LiMn₂O₄ thin films with better electrode performance for lithium ion micro-batteries.     

Advanced electrochemical performance of LiMn1.4Cr0.2Ni0.4O4 as 5 V cathode material by citric-acid-assisted method

Spinel LiMn₂O₄ and LiMn_1.4Cr_0.2Ni_0.4O₄ cathode materials were successfully synthesized by the citric-acid-assisted sol-gel method with ultrasonic irradiation stirring. The structure and electrochemical performance of the as-prepared powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectrometer, cyclic voltamogram (CV) and the galvanostatic charge-discharge test in detail. XRD shows that all the samples have high phase purity, and the powders are well crystallized. SEM exhibits that LiMn_1.4Cr_0.2Ni_0.4O₄ has more uniform cubic-structure morphology than that of LiMn₂O₄. EDX reveals that a small amount of Mn³⁺ still exists in LiMn_1.4Cr_0.2Ni_0.4O₄. The galvanostatic charge-discharge test indicates that the initial discharge capacities for the LiMn_1.4Cr_0.2Ni_0.4O₄ and LiMn₂O₄ at 0.15 C discharge rates are 130.8 and 130.2 mAh g⁻¹, respectively. After 50 cycles, their capacity are 94.1% and 85.1%, respectively. The CV curve implies that Ni and Cr dual substitutions are beneficial to the reversible intercalation and deintercalation of Li⁺, and suppress Mn³⁺ generation at high temperatures and provide improved structural stability.     

Electrochemical behaviour of nano-sized spinel LiMn2O4 and LiAlxMn2−xO4 (x=Al: 0.00-0.40) synthesized via fumaric acid-assisted sol-gel synthesis for use in lithium rechargeable batteries

Pristine spinel LiMn₂O₄ and LiAl_xMn_2−xO₄ (x=Al: 0.00-0.40) with sub-micron sized particles have been synthesized using fumaric acid as chelating agent by sol-gel method. The synthesized samples were subjected to thermogravimetric analysis (TGA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and cyclic voltammetry (CV) and galvanostatic cycling studies. The TGA curve of the gel shows several weight-loss regions stepwise amounting to 55% till 800 °C attributed to the decomposition of the precursors. Calcination to higher temperatures (800 °C) yields pure-phase spinel (LiAl_xMn_2−xO₄), as it is evident from the high-intensity XRD reflections matching to the standard pattern. SEM and TEM studies confirm that the synthesized grains are of uniform regular surface morphology. FT-IR studies show stretching and bending vibration bands of Li-O, Li-Al-Mn-O. LiAl_0.1Mn_1.90O₄ spinel was found to deliver discharge capacity of 139 mA h/g during the first cycle with columbic efficiency of 97%. LiAl_0.1Mn_1.90O₄ spinel exhibits the high cathodic peak current indicating better electrochemical performance. Low doping (x=0.1) of Al is found to be beneficial in stabilizing the spinel structure.     

Columnar-grown porous films of lithium manganese oxide spinel (LiMn2O4) prepared by ultrasonic spray deposition

Using LiNO₃ and Mn(Ac)₂ as raw materials, ultrasonic spray deposition (USD) technique was used to fabricate LiMn₂O₄ films on platinum substrate at different substrate temperatures from 310 to 390 °C. The prepared thick films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Electrochemical performance of the USD-derived films was also evaluated with LiMn₂O₄/Li cells. It is found that all of the LiMn₂O₄ films are porous and composed of orderly oriented columnar particles. The substrate temperature affects the fine microstructure of the columnar particles. The film prepared at 360 °C substrate temperature give rise to best electrochemical behavior.     

Significance of Mg doped LiMn2O4 spinels as attractive 4 V cathode materials for use in lithium batteries

LiMn₂O₄ spinel is one of the most promising cathode materials for lithium-ion batteries because of its cheapness and eco-friendliness. Due to Jahn-Teller distortion, the capacity fades, however, upon repeated cycling. Attempts are being made to improve the cycle life of the spinel by substitution of manganese with other cations. In this paper we report the effect of partial substitution of manganese by Mg²⁺ ions in the LiMn₂O₄ phase. LiMg_yMn_2−yO₄ (y=0 – 0.3) has been synthesized by a thermal method and characterized using XRD, TG/DTA and FTIR. The electrochemical performance is correlated with the dopant concentration.     

Phase transition in multiferroic YMnO3 and its solid solution YMn(0.93)Fe(0.07)O3

Ceramics of YMnO₃ and its Fe substituted YMn_(0.93)Fe_(0.07)O₃ solid solution were synthesized by solid state reaction of the oxides at 1200 °C. Hexagonal phase was identified in both cases by X-ray powder diffraction. Rietveld refinement of cell parameters showed an increase of the parameter values for the solid solution. Dielectric permittivity measurements versus temperature showed a phase transition at 655 °C for yttrium manganite, however, for the solid solution no phase transition was detected on heating up to 700 °C. Dielectric loss measurements showed higher slope changes and better defined local maxima for the solid solution than for the pure phase.     

Effect of temperature on lithium-ion intercalation kinetics of LiMn1.5Ni0.5O4-positive-electrode material

LiMn_1.5Ni_0.5O₄ is synthesized by a sol–gel method and the intercalation kinetics as positive electrode for lithium-ion batteries is investigated by EIS. LiMn_1.5Ni_0.5O₄ particles prepared via sol–gel process possess spinel phase with Fd-3m space group. The charge-transfer resistance, the exchange-current density and the solid-phase diffusion are found as a function of temperature. The apparent activation energy of the exchange current, the charge transfer, and the lithium diffusion in solid phase are also determined, respectively. This result indicates that the effect of the temperature on the cell capacity and the current dependence of the capacity results mainly from the enhancement of the lithium diffusion at elevated temperatures. It can be concluded that LiMn_1.5Ni_0.5O₄ cell has a bad rate cycling performance at elevated temperatures before any modification due to the high diffusion apparent activation energy. The relevant theoretical elucidations thus provide us some useful insights into the design of novel LiMn_1.5Ni_0.5O₄-based positive-electrode materials.     

Immiscibility in the NiFe2O4-NiCr2O4 spinel binary

The solid solution behavior of the Ni(Fe_1−nCr_n)₂O₄ spinel binary is investigated in the temperature range 400-1200 °C. Non-ideal solution behavior, as exhibited by non-linear changes in lattice parameter with changes in n, is observed in a series of single-phase solids air-cooled from 1200 °C. Air-annealing for 1 year at 600 °C resulted in partial phase separation in a spinel binary having n=0.5. Spinel crystals grown from NiO, Fe₂O₃ and Cr₂O₃ reactants, mixed to give NiCrFeO₄, by Ostwald ripening in a molten salt solvent, exhibited single-phase stability down to about 750 °C (the estimated consolute solution temperature, T_cs). A solvus exists below T_cs. The solvus becomes increasingly asymmetric at lower temperatures and extrapolates to n values of 0.2 and 0.7 at 300 °C. The extrapolated solvus is shown to be consistent with that predicted using a primitive regular solution model in which free energies of mixing are determined entirely from changes in configurational entropy at room temperature.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Characteristics of spherical-shaped Li4Ti5O12 anode powders prepared by spray pyrolysis

Spherical-shaped Li₄Ti₅O₁₂ anode powders with a mean size of 1.5 μm were prepared by spray pyrolysis. The precursor powders obtained by spray pyrolysis had no peaks of crystal structure of Li₄Ti₅O₁₂. The powders post-treated at temperatures of 800 and 900 °C had the single phase of spinel Li₄Ti₅O₁₂. The powders post-treated at a temperature of 1000 °C had main peaks of the Li₄Ti₅O₁₂ phase and small impurity peaks of Li₂Ti₃O₇. The spherical shape of the precursor powders was maintained after post-treatment at temperatures below 800 °C. The Brunauer-Emmett-Teller (BET) surface areas of the Li₄Ti₅O₁₂ anode powders post-treated at temperatures of 700, 800 and 900 °C were 4.9, 1.6 and 1.5 m²/g, respectively. The initial discharge capacities of Li₄Ti₅O₁₂ powders were changed from 108 to 175 mAh/g when the post-treatment temperatures were changed from 700 to 1000 °C. The maximum initial discharge capacity of the Li₄Ti₅O₁₂ powders was obtained at a post-treatment temperature of 800 °C, which had good cycle properties below current densities of 0.7 C.     

Improvement of electrochemical performance of all-solid-state lithium secondary batteries by surface modification of LiMn2O4 positive electrode

To improve the electrochemical performance of an all-solid-state In/80Li₂S⋅20P₂S₅ (electrolyte)/LiMn₂O₄ cell, a lithium-titanate thin film was used to coat LiMn₂O₄. The interfacial resistance between LiMn₂O₄ and the electrolyte (measured after initial charging) decreased when the LiMn₂O₄ particles were coated with lithium-titanate. A cell with lithium-titanate-coated LiMn₂O₄ had a higher capacity than a cell with noncoated LiMn₂O₄ for current densities in the range 0.064 to 2.6 mA cm^− 2. Additionally, a cell with coated LiMn₂O₄ retained 96% of the 10th-cycle reversible capacity at a current density of 0.064 mA cm^− 2 after 50 cycles.     

Dielectric properties of Bismuth Titanate (Bi4Ti3O12) synthesized using solution combustion route

Ferroelectric Bismuth Titanate (Bi₄Ti₃O₁₂) was prepared by solution combustion route with glycine as fuel. The single phase Bismuth Titanate was obtained after calcination at 800 °C, which was confirmed with the help of X-ray diffraction studies and EDS analysis. SEM micrographs of the calcined powders show agglomerated particles, which is typical of combustion synthesis. Behavior of dielectric constant and dielectric loss as a function of temperature of as prepared sample are reported here. Ferroelectric to paraelectric phase transition occurs at the temperature T_c∼650 °C. Impedance studies were made in the frequency range from 1 KHz to 1 MHz. The semicircles observed in the complex impedance diagrams indicate deviation from the Debye behavior. Activation energy of the sample around T_c is found to be ∼0.35 eV and below T_c is ∼0.13 eV, which was calculated using the Arrhenius plots.     

Hydrothermal preparation and photoluminescent properties of MgAl2O4: Eu spinel nanocrystals

Nanoplates of the MgAl₂O₄ spinel doped with Eu³⁺ ions were prepared by a microwave assisted hydrothermal method. Structural properties of the precursor calcined at 700 and 1000 ^oC powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). According to the obtained XRD patterns the formation of single-phase spinels after calcination was confirmed. The average spinel particle size was determined to be 11 nm after calcination at 700 °C and it increased up to 14 nm after calcination at 1000 °C. The photoluminescent properties of prepared powders with different Eu³⁺ ion concentrations (0-5% mol) were investigated using excitation and emission spectroscopy at room and low temperatures (77 K).     

Effects of annealing temperature on structure and magnetic properties of CoAl0.2Fe1.8O4/SiO2 nanocomposites

CoAl_0.2Fe_1.8O₄/SiO₂ nanocomposites were prepared by sol–gel method. The effects of annealing temperature on the structure and magnetic properties of the samples were studied by X-ray diffraction, transmission electron microscopy, vibrating sample magnetometer and Mössbauer spectroscopy. The results show that the CoAl_0.2Fe_1.8O₄ in the samples exhibits a spinel structure after being annealed. As annealing temperature increases from 800 to 1200 °C, the average grain size of CoAl_0.2Fe_1.8O₄ in the nanocomposites increases from 5 to 41 nm while the lattice constant decreases from 0.8397 to 0.8391 nm, the saturation magnetization increases from 21.96 to 41.53 emu/g. Coercivity reaches a maximum of 1082 Oe for the sample annealed at 1100 °C, and thereafter decreases with further increasing annealing temperature. Mössbauer spectra show that the isomer shift decreases, hyperfine field increases and the samples transfer from mixed state of superparamagnetic and magnetic order to the completely magnetic order with annealing temperature increasing from 800 to 1200 °C.     

Comparative study of structural and magnetic properties of nano-crystalline Li0.5Fe2.5O4 prepared by various methods

Lithium ferrite has been considered as one of the highly strategic magnetic material. Nano-crystalline Li_0.5Fe_2.5O₄ was prepared by four different techniques and characterized by X-ray diffraction, vibrating sample magnetometer (VSM), transmission electron microscope (TEM) and Fourier transform infrareds (FTIR). The effect of annealing temperature (700, 900 and 1050 °C) on microstructure has been correlated to the magnetic properties. From X-ray diffraction patterns, it is confirmed that the pure phase of lithium ferrite began to form at 900 °C annealing. The particle size of as-prepared lithium ferrite was observed around 40, 31, 22 and 93 nm prepared by flash combustion, sol-gel, citrate precursor and standard ceramic technique, respectively. Lithium ferrite prepared by citrate precursor method shows a maximum saturation magnetization 67.6 emu/g at 5 KOe.     

High pressure Raman spectroscopic study of spinel MgCr2O4

An in situ Raman spectroscopic study was conducted to investigate the pressure induced phase transformation of MgCr₂O₄ spinel up to pressures of 76.4 GPa. Results indicate that MgCr₂O₄ spinel undergoes a phase transformation to the CaFe₂O₄ (or CaTi₂O₄) structure at 14.2 GPa, and this transition is complete at 30.1 GPa. The coexistence of two phases over a wide range of pressure implies a sluggish transition mechanism. No evidence was observed to support the pressure-induced dissociation of MgCr₂O₄ at 5.7-18.8 GPa, predicted by the theoretical simulation. This high pressure MgCr₂O₄ polymorphism remains stable upon release of pressure, but at ambient conditions, it transforms to the spinel phase.     

Charge-discharge characteristics of nanocrystalline Co3O4 powders via aerosol flame synthesis

Nanocrystalline Co₃O₄ powders were synthesized by aerosol flame synthesis (AFS) method for the anode of lithium ion batteries and the basic electrochemical properties were investigated. The effects of synthesis conditions and heat-treatment temperature on the morphology, crystallite size and electrochemical properties were investigated. As-prepared soot contained Co₃O₄, CoO and Co(OH)₂, which were eventually converted into cubic spinel Co₃O₄ by post heat treatment. The as-prepared particle size was in the range of 10-30 nm and grew to 50-85 nm by the heat treatment. With growing particle size and improved crystallinity, charge-discharge capacity and cycle performance were improved and the discharge capacity of the powder heat-treated at 700 °C was 571 mAh/g after 30 cycles, which was better than Co₃O₄ powder reported in the previous literature.