Electrochemical Sensor Based on Oxidation of 2,8‐Dihydroxyadenine to Monitor DNA Damage in Calf Thymus DNA

A novel and reliable direct electrochemical method has been established to monitor DNA damage in acid hydrolyzed calf thymus DNA, based on the determination of 2,8‐dihydroxyadenine (2,8‐DHA). A single‐wall carbon nanotubes (SWCNT) modified edge plane pyrolytic graphite electrode (EPPGE) has been used as a sensor to monitor the DNA damage. 2,8‐DHA the main in vivo adenine oxidation product undergoes oxidation at ～395 mV at SWCNT modified EPPGE using square wave voltammetry (SWV). The sensor exhibits potent and persistent electron‐mediating behavior. A well‐defined oxidation peak for the oxidation of 2,8‐DHA was observed at modified electrode with lowering of peak potential and increase in peak current as compared to bare EPPGE. At optimal experimental conditions, the catalytic oxidative peak current was responsive with the 2,8‐DHA concentrations ranging from 0.05 nM to 100 nM. The detection limit was 3.8×10^?11 M and limit of quantification was 1.27×10^?10 M. The modified electrode exhibited high stability and reproducibility.     

Fabrication of Chitosan‐Multiwall Carbon Nanotube Nanocomposite Containing Ferri/Ferrocyanide: Application for Simultaneous Detection of D‐Penicillamine and Tryptophan

We report a simple and effective strategy for fabrication of the nanocomposite containing chitosan (CS) and multiwall carbon nanotube (MWNT) coated on a glassy carbon electrode (GCE). The characterization of the modified electrode (CS‐MWNT/GC) was carried out using scanning electron microscopy (SEM) and UV–vis absorption spectroscopy. The electrochemical behavior of CS‐MWNT/GC electrode was investigated and compared with the electrochemical behavior of chitosan modified GC (CS/GC), multiwalled carbon nanotube modified GC (MWNT/GC) and unmodified GC using cyclic voltammetry (CV) and electron impedance spectroscopy (EIS). The chitosan films are electrochemically inactive; similar background charging currents are observed at bare GC. The chitosan films are permeable to anionic Fe(CN)₆^3?/4? (FC) redox couple. Electrochemical parameters, including apparent diffusion coefficient for the Fe(CN)₆^3?/4? redox probe at FC/CS‐MWNT/GC electrode is comparable to values reported for cast chitosan films. This modified electrode also showed electrocatalytic effect for the simultaneous determination of D‐penicillamine (D‐PA) and tryptophan (Trp). The detection limit of 0.9 μM and 4.0 μM for D‐PA and Trp, respectively, makes this nanocomposite very suitable for determination of them with good sensitivity.     

Highly Sensitive Electrochemical Sensor for Nitric Oxide Using the Self‐Assembled Monolayer of 1,8,15,22‐Tetraaminophthalocyanatocobalt(II) on Glassy Carbon Electrode

Glassy carbon (GC) electrode modified with a self‐assembled monolayer (SAM) of 1,8,15,22‐tetraaminophthalocyanatocobalt(II) (4α‐Co^IITAPc) was used for the selective and highly sensitive determination of nitric oxide (NO). The SAM of 4α‐Co^IITAPc was formed on GC electrode by spontaneous adsorption from DMF containing 1 mM 4α‐Co^IITAPc. The SAM showed two pairs of well‐defined redox peaks corresponding to Co^III/Co^II and Co^IIIPc^?1/Co^IIIPc^?2 in 0.2 M phosphate buffer (PB) solution (pH 2.5). The SAM modified electrode showed excellent electrocatalytic activity towards the oxidation of nitric oxide (NO) by enhancing its oxidation current with 310 mV less positive potential shift when compared to bare GC electrode. In amperometric measurements, the current response for NO oxidation was linearly increased in the concentration range of 3×10^?9 to 30×10^?9 M with a detection limit of 1.4×10^?10 M (S/N=3). The proposed method showed a better recovery for NO in human blood serum samples.     

Comparison of Boron‐Doped Diamond and Glassy Carbon Electrodes for Determination of Procaine Hydrochloride

The electrochemical oxidation of procaine hydrochloride (PC?HCL, 2‐diethylaminoethyl 4‐aminobenzoate hydrochloride) was investigated at as‐deposited boron‐doped diamond (ad‐BDD) electrode, anodically oxidized BDD (ao‐BDD) electrode and glassy carbon (GC) electrode using cyclic voltammetry (CV). Well‐defined cyclic voltammograms were obtained for PC?HCL oxidation with high signal‐to‐background (S/B) ratio, low tendency for adsorption, good reproducibility and long‐term stability at ad‐BDD electrode, demonstrating its superior electrochemical behavior and significant advantages in contrast to ao‐BDD and GC electrode. At 100 μM PC?HCL, the voltammetric S/B ratio was nearly one order of magnitude higher at an ad‐BDD electrode than that at a GC electrode. In a separate set of experiments for oxidation of 100 μM PC?HCL, 96%, 92% and 84% of the initial oxidation peak current was retained at the ad‐BDD, ao‐BDD and GC electrode, respectively, by stirring the solution after the tenth cycle. The current response was linearly proportional to the square root of the scan rate within the range 10–1000 mV s^?1 in 10 μM PC?HCL solutions, indicating that the oxidation process was diffusion‐controlled with negligible adsorption at an ad‐BDD surface. The good linearity was observed for a concentration range from 5 to 200 μM with a linear equation of y=0.03517x+0.65346 (r=0.999), and the detection limit was 0.5 μM for oxidation of PC?HCL at the ad‐BDD electrode. The ad‐BDD electrode could maintain 100% of its original activity after intermittent use for 3 months.     

Electrochemical Determination of the Herbicide Bentazone Using a Carbon Nanotube β‐Cyclodextrin Modified Electrode

An electrochemical sensor has been developed for the determination of the herbicide bentazone, based on a GC electrode modified by a combination of multiwalled carbon nanotubes (MWCNT) with β‐cyclodextrin (β‐CD) incorporated in a polyaniline film. The results indicate that the β‐CD/MWCNT modified GC electrode exhibits efficient electrocatalytic oxidation of bentazone with high sensitivity and stability. A cyclic voltammetric method to determine bentazone in phosphate buffer solution at pH 6.0, was developed, without any previous extraction, clean‐up, or derivatization steps, in the range of 10–80 µmol L^?1, with a detection limit of 1.6 µmol L^?1 in water. The results were compared with those obtained by an established HPLC technique. No statistically significant differences being found between both methods.     

N‐(3,4‐Dihydroxyphenethyl)‐3,5‐dinitrobenzamide‐Modified Multiwall Carbon Nanotubes Paste Electrode as a Novel Sensor for Simultaneous Determination of Penicillamine,Uric acid,and Tryptophan

N‐(3,4‐dihydroxyphenethyl)‐3,5‐dinitrobenzamide modified multiwall carbon nanotubes paste electrode was used as a voltammetric sensor for oxidation of penicillamine (PA), uric acid (UA) and tryptophan (TP). In a mixture of PA, UA and TP, those voltammograms were well separated from each other with potential differences of 300, 610, and 310 mV, respectively. The peak currents were linearly dependent on PA, UA and TP concentrations in the range of 0.05–300, 5–420, and 1.0–400 µmol L^?1, with detection limits of 0.021, 2.0, and 0.82 µmol L^?1, respectively. The modified electrode was used for the determination of those compounds in real samples.     

Electrochemical Determination of 2‐Nitrophenol in Water Samples Using Mg‐Al‐SDS Hydrotalcite‐Like Clay Modified Glassy Carbon Electrode

A glassy carbon electrode (GCE) modified with Mg‐Al‐SDS hydrotalcite‐like clay (SDS‐HTLC) was used for the sensitive voltammetric determination of 2‐nitrophenol (2‐NP) utilizing the oxidation process. The results indicate the prepared modified electrode has an excellent electrocatalytic activity toward 2‐NP oxidation, lowering the oxidation overpotential and increasing the oxidation current. Under optimal conditions, the oxidation current was proportional to 2‐NP concentration in the range from 1.0×10^?6 to 6.0×10^?4 M with the detection limit of 5.0×10^?7 M by DPV (S/N=3). The fabricated electrode was applied for 2‐NP determination in water samples and the recovery for these samples was from 95.6 to 103.5%.     

Sensitive amperometric pyridoxine sensor based on self‐assembled Prussian blue nanoparticle‐modified poly(o‐phenylenediamine)/glassy carbon electrode

Prussian blue nanoparticles (PBNPs) were prepared by a self‐assembly process on a glassy carbon electrode (GCE) modified with poly(o‐phenylenediamine) (PoPD) film. The stepwise fabrication process of PBNP‐modified PoPD/GCE was characterized using scanning electron microscopy and electrochemical impedance spectroscopy. The prepared PBNPs showed an average size of 70 nm and a homogeneous distribution on the surface of the modified electrode. The PBNPs/PoPD/GCE showed electrocatalytic activity towards the oxidation of pyridoxine (PN) and was used as an amperometric sensor. The modified electrode exhibited a linear response for PN oxidation over the concentration range 3–38.5 μM with a detection limit of ca 6.10 × 10^?7 M (S/N = 3) and sensitivity of 2.79936 × 10³ mA M^?1 cm^?2 using an amperometric method. The mechanism and kinetics of the catalytic oxidation reaction of PN were investigated using cyclic voltammetry and chronoamperometry. The values of α, k_cat and D were estimated as 0.36, 1.089 × 10² M^?1 s^?1 and 8.9 × 10^?5 cm² s^?1, respectively. This sensor also exhibited good anti‐interference and selectivity. Copyright © 2016 John Wiley & Sons, Ltd.     

Electrochemical Determination of Pyrogallol at Conducting Poly(3,4‐ethylenedioxythiophene) Film‐Modified Screen‐Printed Carbon Electrodes

The electrochemical oxidation of pyrogallol at electrogenerated poly(3,4‐ethylenedioxythiophene) (PEDOT) film‐modified screen‐printed carbon electrodes (SPCE) was investigated. The voltammetric peak for the oxidation of pyrogallol in a pH 7 buffer solution at the modified electrode occurred at 0.13 V, much lower than the bare SPCE and preanodized SPCE. The experimental parameters, including electropolymerization conditions, solution pH values and applied potentials were optimized to improve the voltammetric responses. A linear calibration plot, based on flow‐injection amperometry, was obtained for 1–1000 µM pyrogallol, and a slope of 0.030 µA/µM was obtained. The detection limit (S/N=3) was 0.63 µM.     

Selective Electrochemical Determination of Dopamine with Molecularly Imprinted Poly(Carbazole‐co‐Aniline) Electrode Decorated with Gold Nanoparticles

Dopamine (DA) is a significant neurotransmitter in the central nervous system, coexisting with uric acid (UA) and ascorbic acid (AA). UA and AA are easily oxidizable compounds having potentials close to that of DA for electrochemical analysis, resulting in overlapping voltammetric response. In this work, a novel molecularly imprinted (MI) electrochemical sensor was proposed for selective determination of DA (in the presence of up to 80‐fold excess of UA and AA), relying on gold nanoparticles (Au_nano)‐decorated glassy carbon (GC) electrode coated with poly(carbazole (Cz)‐co‐aniline (ANI)) copolymer film incorporating DA as template (DA imprinted‐GC/P(Cz‐co‐ANI)‐Au_nano electrode, DA‐MIP‐Au_nano electrode). The DA recognizing sensor electrode showed great electroactivity for analyte oxidation in 0.2 mol L^?1 pH 7 phosphate buffer. Square wave voltammetry (SWV) was performed within 10^?4–10^?5 mol L^?1 of DA, of which the oxidation peak potential was observed at 0.16 V. The limit of detection (LOD) and limit of quantification (LOQ) were 2.0×10^?6 and 6.7×10^?6 mol L^?1, respectively. Binary and ternary synthetic mixtures of DA‐UA, DA‐AA and DA‐UA‐AA yielded excellent recoveries for DA. Additionally, DA was quantitatively recovered from a real sample of bovine serum spiked with DA, and determined in concentrated dopamine injection solution. The developed SWV method was statistically validated against a literature potentiodynamic method using a caffeic acid modified‐GC electrode.     

Electrocatalytic Properties of a Novel Poly‐1‐Naphthylamine‐Modified Electrode Using Ascorbic Acid as Molecule Probe

A glassy carbon electrode was modified with an electropolymerized film of 1‐naphthylamine in aqueous solution. The electrocatalytic properties of this modified electrode (ME) were investigated using ascorbic acid (AA) as probe molecule. The electrochemical behavior of AA in buffer solution was examined by voltammetry and amperometry. The results showed that the ME exhibited good electrocatalytic activity towards the oxidation of AA, as a consequence, it can be used as amperometric sensor of this analyte in a flow injection system with good sensitivity. Calibration curves were linear over the concentration range 0.05–1.50 mM with a phosphate buffer solution pH 3 as the carrier, the detection limit was 1 ppm (S/N=3). The methods were applied to the determination of AA in beverages and pharmaceutical products. A good correlation with a reference method was attained.     

Evaluation of Meldola Blue‐Carbon Nanotube‐Sol‐Gel Composite for Electrochemical NADH Sensors and Their Application for Lactate Dehydrogenase‐Based Biosensors

A novel MB‐SWNT‐sol‐gel nanocomposite material was prepared by the sol‐gel process incorporating a redox mediator and carbon nanotubes. The electrocatalytic properties of the nanomaterial based sensor toward NADH oxidation were studied by electrochemical measurements. Significant enhancement of oxidation current is obtained at electrodes modified by MB‐SWNT‐sol‐gel in comparison with the analogous carbon black and/or graphite composite modified electrode. The usefulness of the nanocomposite material as a matrix for immobilizing enzymes is also demonstrated. Analytical parameters of D ‐lactate biosensors with and without SWNT in the hybrid film were compared demonstrating that performance of the biosensor was significantly improved when introducing SWNT.     

Selective Detection of Ascorbic Acid Using Octacyanomolybdate‐Doped‐Glutaraldehyde‐Cross‐Linked Poly‐L‐Lysine Film Modified Glassy Carbon Electrode

The present work describes oxidation of ascorbic acid (AA) at octacyanomolybdate‐doped‐glutaraldehyde‐cross‐linked poly‐L ‐lysine (PLL‐GA‐Mo(CN) film modified glassy carbon electrode in 0.1 M H₂SO₄. The modified electrode has been successfully prepared by means of electrostatically trapping Mo(CN) mediator in the cationic film of glutaraldehyde‐cross‐linked poly‐L ‐lysine. The dependence of peak current of modified electrode in pure supporting indicates that the charge transfer in the film was a mixed process at low scan rates (5 to 200 mV s^?1), and kinetically restrained at higher scan rates (200 to 1000 mV s^?1). Cyclic voltammetry and rotating disk electrode (RDE) techniques are used to investigate the electrocatalytic oxidation of ascorbic acid and compared with its oxidation at bare and undoped PLL‐GA film coated electrodes. The rate constant of catalytic reaction k obtained from RDE analysis was found to be 9.5×10⁵ cm³ mol^?1 s^?1. The analytical determination of ascorbic acid has been carried out using RDE technique over the physiological interest of ascorbic acid concentrations with a sensitivity of 75 μA mM^?1. Amperometric estimation of AA in stirred solution shows a sensitivity of 15 μA mM^?1 over the linear concentration range between 50 and 1200 μM. Interestingly, PLL‐GA‐Mo(CN) modified electrode facilitated the oxidation of ascorbic acid but not responded to other electroactive biomolecules such as dopamine, uric acid, NADH, glucose. This unique feature of PLL‐GA‐Mo(CN) modified electrode allowed for the development of a highly selective method for the determination of ascorbic acid in the presence of interferents.     

Detection of Thiols by o‐Quinone Nanocomposite Modified Electrodes

A chemically modified glassy carbon (GC) electrode was developed as an amperometric sensor for detection of biological thiols. The electrode was modified by inclusion of co‐enzyme pyrroloquinoline quinone (PQQ) and a co‐catalyst of oxidized single wall carbon nanotubes (Ox‐SWNT) into a gold polypyrrole (Au‐PPy) nanocomposite matrix. The electrode (PQQ/Ox‐SWNT/Au‐PPy/GC) was characterized using scanning electron microscopy and cyclic voltammetry. Optimal conditions for the PQQ/Ox‐SWNT/Au‐PPy/GC electrode were determined and then utilized for the amperometric detection of L‐cysteine, N‐acetyl‐L‐cysteine, L‐penicillamine and D, L‐glutathione. The electrochemical response for each thiol in pH 3.2 citrate phosphate buffer at +450 mV (vs. Ag/AgCl) was found to be linear with limit of detections (LOD, S/N=3) ranging from 0.50 µM for L‐penicillamine to 1.55 µM for D, L‐glutathione with sensitivities of 30.2 nA/µM and 3.6 nA/µM respectively. The electrode design is simple and easy to construct using a minimum amount of co‐enzyme and co‐catalyst, resulting in detection methods with very good stability and improved sensitivity for thiol detection.     

A NADH Sensor Based on 1,2‐Naphththoquinone Electropolymerized on Multi‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

A new carbon nanotubes modified electrode (poly‐Nq‐MWCNTs/GCE) was fabricated by electropolymerization of 1,2‐naphththoquinone to the surface of multi‐walled carbon nanotubes modified electrode by casting method. The morphology of the nanocomposite was characterized by scanning electron microscopy. Cyclic voltammetry and chronoamperometry were applied to investigate the electrochemical properties of the poly‐Nq‐MWCNTs nanocomposite modified electrode. The result of electrochemical experiments showed that such modified electrode had a favorable catalytic ability to oxidation of β‐nicotinamide adenine dinucleotide (NADH). The resulted sensor was sensitiveness to NADH and achieved 95β of the steady‐state current within 5s. Furthermore, the anodic peak current was linear to the concentration of NADH for the range from 1.0 μM to 0.14 mM. The linear equation was: I(μA) = 0.3987 + 0.1035c (μmol/L), the correlation coefficient r = 0.9962, the detect limit is down to 1 × 10^?7 M (S/N = 3) and the sensitivity is 0.1035 μA/mmol. The well catalytic activity of the sensor was ascribed to the synergistic effect role played by MWCNTs and poly‐Nq. Moreover, the based sensor possesses good stability and reproducibility.     

Electrocatalytic Determination of 6‐Tioguanine at a p‐Aminophenol Modified Carbon Paste Electrode

A p‐aminophenol modified carbon paste electrode (p‐APMCPE) was constructed for determination of an anticancer drug 6‐thioguanine (6‐TG). The cyclic voltammogram showed that the electrocatalytic oxidation of 6‐TG at the surface of p‐APMCPE occurs at a potential about 840 mV less positive than at an unmodified electrode. Square‐wave voltammetry results presented that the electrocatalytic oxidation peak currents of 6‐TG in pH 9.0 had two linear dynamic ranges in the range of 0.2 to 8.0 and 8.0 to 350.0 μM 6‐TG with a detection limit of 0.08 μM. The kinetic parameters such as electron transfer coefficient (α) and rate constant were determined for the chemical reaction between 6‐TG and p‐aminophenol. Finally, this method was evaluated for the determination of 6‐TG in 6‐thioguanine tablets and urine samples.     

Methylthiouracil‐modified Carbon Paste Electrode as a New Voltammetric Sensor Based on a 1,4‐Michael Addition Reaction for Detection of Dopamine

A sensitive dopamine sensor was constructed based on the modified carbon paste electrode with methylthiouracil as a nucleophile in the 1,4‐Michael addition reaction. An ECE mechanism was suggested for dopamine oxidation at the modified electrode. Design of experiments was used in the optimization of variables. Under the optimum conditions, calibration graph was linear in the range of 0.20–15.0 µM with a detection limit of 73 nM. The relative standard deviations (n=5) for 0.50 µM of dopamine was 3.83 %. The selectivity of the sensor was also studied. The developed sensor was applied for analysis of pharmaceutical and biological samples.     

Determination of Phenolic Compounds Based on the Tyrosinase‐ Single Walled Carbon Nanotubes Sensor

An amperometric sensor to phenolic compound was successfully constructed by immobilizing tyrosinase on the SWNTs modified glassy carbon (GC) electrode, which was covered with Nafion film. The sensitivity of the tyrosinase‐SWNTs sensor to phenol was 155 μA/mM. The tyrosinase‐SWNTs sensor also had good response to catechol, p‐chlorophenol and m‐cresol. Furthermore, benzoic acid could be detected based on the inhibition to tyrosinase activity.     

Fabrication of Glucose Biosensor Based on Encapsulation of Glucose‐Oxidase on Sol‐Gel Composite at the Surface of Glassy Carbon Electrode Modified with Carbon Nanotubes and Celestine Blue

A simple procedure was developed to prepare a glassy carbon electrode modified with multi walled carbon nanotubes (MWCNTs) and Celestin blue. Cyclic voltammograms of the modified electrode show stable and a well defined redox couple with surface confined characteristic at wide pH range (2–12). The formal potential of redox couple (E′) shifts linearly toward the negative direction with increasing solution pH. The surface coverage of Celestine blue immobilized on CNTs glassy carbon electrode was approximately 1.95×10^?10 mol cm^?2. The charge transfer coefficient (α) and heterogeneous electron transfer rate constants (k_s) for GC/MWCNTs/Celestine blue were 0.43 and 1.26 s^?1, respectively. The modified electrode show strong catalytic effect for reduction of hydrogen peroxide and oxygen at reduced overpotential. The glucose biosensor was fabricated by covering a thin film of sol‐gel composite containing glucose oxides (GOx) on the surface of Celestine blue /MWCNTs modified GC electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The detection limit, sensitivity and liner calibration rang were 0.3 μM, 18.3 μA/mM and 10 μM–6.0 mM, respectively. The accuracy of the biosensor for glucose detection was evaluated by detection of glucose in a serum sample, using standard addition protocol. In addition biosensor can reach 90% of steady currents in about 3.0 sec and interference effect of the electroactive existing species (ascorbic acid–uric acid and acetaminophen) was eliminated. Furthermore, the apparent Michaelis–Menten constant 2.4 mM, of GOx on the nano composite exhibits excellent bioelectrocatalytic activity of immobilized enzyme toward glucose oxidation. Excellent electrochemical reversibility of redox couple, high stability, technically simple and possibility of preparation at short period of time are of great advantages of this procedure for modification of glucose biosensor.     

Study of Factors Affecting the Performance of Voltammetric Copper Sensors Based on Gly‐Gly‐His Modified Glassy Carbon and Gold Electrodes

This paper reports a study of the factors affecting the analytical performance of gold and glassy carbon electrodes modified with the tripeptide Gly‐Gly‐His for the detection of copper ions. Gly‐Gly‐His is attached to a glassy carbon (GC) surface modified with 4‐carboxyphenyl moieties or a gold surface modified with 3‐mercaptopropionic acid by the reaction of the N‐terminal amine group of the peptide with the carboxylic acid groups of the monolayer via carbodiimide activation. X‐ray photoelectron spectroscopy was used to characterize the steps in the biosensor fabrication. It was found that the analytical performance of a sensor prepared with Gly‐Gly‐His on a GC electrode was similar to that on a gold electrode under the same conditions. The performance was greatly enhanced at higher temperature, no added salt during copper accumulation and longer accumulation time within a pH range of 7–9. Interference studies and investigations of stability of the Gly‐Gly‐His sensor are reported. Analysis of natural water samples show that the sensors measure only copper ions that can complex at the sensor surface. Strongly complexed copper in natural water is not measured. Despite greater stability of diazonium salt derived monolayers on carbon surfaces compared with alkanethiols self‐assembled monolayers on gold, the stability of the sensors was essentially the same regardless of the modification procedure.