Synthesis of poly(styrene-graft-ethylene oxide) by ethoxylation of amide group containing styrene copolymers

Graft copolymers containing poly(ethylene oxide) side chains on a polystyrene backbone have been synthesized. Styrene copolymers synthesized by free radical mechanism and containing between 5 and 15 mol % acrylamide or methacrylamide were used as backbones. The amide groups in the copolymers were ionized by using potassium tert-butoxide or potassium naphthalene, and grafting was achieved by utilizing the amide anions as initiator sites for the polymerization of ethylene oxide in 2-ethoxyethyl ether at 65°C. The graft copolymers were characterized with respect to molecular weight and composition using elemental analysis, NMR, gel permeation chromatography, IR, and viscosity measurements. The size of the side chains were between 600 and 2000 g/mol. GPC results from a hydrolyzed graft copolymer sample suggest a narrow size distribution for the poly(ethylene oxide) grafts. Solution properties of the graft copolymers were investigated in different toluene/methanol mixtures. The intrinsic viscosities of the graft copolymers were found to depend primarily on the poly(ethylene oxide) content rather than the graft density or the poly(ethylene oxide) chain length. © 1993 John Wiley & Sons, Inc.     

Control of the PEO chain conformation on nanoparticles by adsorption of PEO-block-poly(L-lysine) copolymers and its significance on colloidal stability and protein repellency

The physical adsorption of PEO(n)-b-PLL(m) copolymers onto silica nanoparticles and the related properties of poly(ethylene oxide) (PEO)-coated particles were studied as a function of the block copolymer composition. Copolymers adopt an anchor-buoy conformation at the particle surface owing to a preferential affinity of poly(L-lysine) (PLL) blocks with the silica surface over PEO blocks when a large excess of copolymer is used. The interdistance between PEO chains at particle surface is highly dependent on the size of PLL segments; a dense brush of PEO is obtained for short PLL blocks (DP = 10), whereas PEO chains adopt a so-called interacting "mushroom" conformation for large PLL blocks (DP = 270). The size of the PEO blocks does not really influence the copolymer surface density, but it has a strong effect on the PEO layer thickness as expected. Salt and protein stability studies led to similar conclusions about the effectiveness of a PEO layer with a dense brush conformation to prevent colloidal aggregation and protein adsorption. Besides, a minimal PEO length is required to get full stabilization properties; as a matter of fact, both PEO(45)-b-PLL(10) and PEO(113)-b-PLL(10) give rise to a PEO brush conformation but only the latter copolymer efficiently stabilizes the particles in the presence of salt or proteins.     

Graft copolymers composed of high molecular weight poly(ethylene oxide) backbone and poly(N-isopropylacrlylamide) side chains and their thermoassociating properties

Novel, water-soluble thermoassociative graft copolymers based on high molecular weight (HMW) poly(ethylene oxide-co-glycidol) backbone and relatively short grafts of poly-N-isopropyl acrylamide (NIPAAm) were prepared. The copolymer precursors with two architectures (block and graft) were synthesized using Ca-amide-alkoxide initiators. The OH groups in the copolymer precursors have been utilized for grafting NIPAAm using ceric ion (Ce⁴⁺) redox initiation. The idea was to imprint the “smart” properties of PNIPAAm grafts into common HMW poly(ethylene oxide). The sensitive moieties undergo reversible association transitions by changing the temperature of dilute and semidilute aqueous solutions of the copolymers. Associative properties were studied by viscosity and rheology measurements. Two types of interactions, induced by heating, depending on the copolymer concentration namely intra- and intermolecular association were observed.     

Responsive colloidal systems: reversible aggregation and fabrication of superhydrophobic surfaces

We report on a method of fabricating stimuli-responsive core-shell nanoparticles using block copolymers covalently bound to a silica nanoparticle surface. We used the "grafting to" approach to graft amphiphilic block copolymer brushes of poly(styrene-b-2-vinylpyridine-b-ethylene oxide) and poly(styrene-b-4-vinylpyridine) onto silica nanoparticles with two different diameters: colloidal silica 200 nm in diameter and fumed silica 15 nm in diameter. We used the pH-responsive properties of the grafted brush to regulate the interactions between the particles, and between the particles and their environment. We show that this behavior can be applied for a reversible formation of particle aggregates, and can be used to tune and stabilize the secondary aggregates of particles of the appropriate size and morphology in an aqueous environment. The suspensions of the particles form a textured hydrophilic coating on various substrates upon casting and the evaporation of water. Heating above the polymer's glass transition temperature or treatment in acidic water result in back and forth switching between superhydrophobic and hydrophilic surfaces, respectively.     

通过RAFT聚合制备SiO2/接枝共聚物纳米杂化粒子

以二氧化硅(SiO2)纳米粒子表面键接的二硫代苯甲酸酯作为可逆加成-断裂-链转移(RAFT)聚合反应的链转移剂, 在室温下引发苯乙烯和马来酸酐进行表面RAFT交替共聚反应, 制得了SiO2/苯乙烯-alt-马来酸酐杂化材料. 通过聚氧化乙烯(PEO)的羟基与马来酸酐的酯化反应, 将PEO接枝到SiO2纳米粒子的表面, 增加了硅粒子的生物相容性. 用FTIR, TGA和TEM对杂化材料的结构、组成和形貌进行了表征.     

PAA/PEO comb polymer effects on rheological properties and inter-particle forces in aqueous silica suspensions

The effects of a poly(acrylic acid) (PAA)-poly(ethylene) (PEO) comb polymer dispersant on the rheological properties and inter-particle forces in aqueous silica suspensions have been studied under varying pH conditions. The comb polymer was found to adsorb more strongly under acidic than basic conditions, indicating that the PAA backbone of the copolymer preferentially adsorbs onto silica surfaces with the PEO "teeth" extending out from the surface into the solution. In the presence of low concentrations of copolymer, the silica suspensions were stable due to electrostatic repulsions between the silica surfaces. At higher copolymer concentrations and under neutral and basic conditions, where the copolymer interacted only weakly with silica, the suspensions showed a transition from a dispersed to weakly flocculated state and attractive forces were measured between silica surfaces. Under acidic conditions, the silica dispersion also destabilized at intermediate copolymer adsorbed density and then was re-stabilized at higher adsorbed coverage. The silica suspensions were stable at high copolymer coverage due to steric repulsions between the particles. The destabilization at intermediate coverage is thought to be due to polymer bridging between particles or possibly depletion forces.     

Solution behavior of [(ethylene-co-vinyl alcohol)-g-ethylene oxide] graft copolymers

The solution behavior of hydrophobic-hydrophilic water-soluble graft copolymers consisting of poly[(ethylene-co-vinyl alcohol)-g-ethylene oxide] was investigated by high-resolution NMR spectroscopy and measurements of solution viscosity in tetrahydrofuran, water, and mixtures thereof at various temperatures. A graft copolymer with a backbone containing 2.7 mole% vinyl alcohol exists in an intramolecular phase-separated conformation in aqueous solution, independent of the temperature. Graft copolymers with backbones containing 20.3 mol% vinyl alcohol exhibit an intramolecular mixed-phase conformation in which the mobility of chains in the hydrophobic region depends on temperature. The temperature dependence of the intrinsic viscosity in water shows a maximum near 50°C.     

A physico-chemical investigation of poly(ethylene oxide)-block-poly(L-lysine) copolymer adsorption onto silica nanoparticles

The adsorption behavior of poly(ethylene oxide)-b-poly(L-lysine) (PEO(113)-b-PLL(10)) copolymer onto silica nanoparticles was investigated in phosphate buffer at pH 7.4 by means of dynamic light scattering, zeta potential, adsorption isotherms and microcalorimetry measurements. Both blocks have an affinity for the silica surface through hydrogen bonding (PEO and PLL) or electrostatic interactions (PLL). Competitive adsorption experiments from a mixture of PEO and PLL homopolymers evidenced greater interactions of PLL with silica while displacement experiments even revealed that free PLL chains could desorb PEO chains from the particle surface. This allowed us to better understand the adsorption mechanism of PEO-b-PLL copolymer at the silica surface. At low surface coverage, both blocks adsorbed in flat conformation leading to the flocculation of the particles as neither steric nor electrostatic forces could take place at the silica surface. The addition of a large excess of copolymer favoured the dispersion of flocs according to a presumed mechanism where PLL blocks of incoming copolymer chains preferentially adsorbed to the surface by displacing already adsorbed PEO blocks. The gradual addition of silica particles to an excess of PEO-b-PLL copolymer solution was the preferred method for particle coating as it favoured equilibrium conditions where the copolymer formed an anchor-buoy (PLL-PEO) structure with stabilizing properties at the silica-water interface.     

The versatile surface properties of poly(cyclopentadiene)-modified silica particles (PCPD–silica): XPS and electrokinetic studies

Surface properties of poly(cyclopentadiene)–silica hybrid particles (PCPD–silica) were studied by means of XPS and electrokinetic measurements. The surfaces of PCPD–silica particles exhibit two different areas with different properties: bare silica holes and PCPD patches. The PCPD chains contain different functional groups such as alcohol and carbonyl groups that were identified by XPS. The PCPD chains are grafted covalently onto the silica surface via Si–O–C bonds created by the reaction of silanol groups and active PCPD chains. The amount of Si–O–C was examinated by means of XPS. The Brønsted acidity of the residual silanol groups was determined by means of electro-kinetic measurements. It was found that the pK _a values of the residual silanol groups increase with increasing polymer content on the particle surface. The surface acceptor strengths of the hybrid particles in non-aqueous liquids were investigated by the solvatochromic indicator bis(1,10-phenanthroline)-cis-dicyano-iron-II in 1,2-dichloroethane.     

Effects of SDS on the thermo- and pH-sensitive structural changes of the poly(acrylic acid)-based copolymer containing both poly(N-isopropylacrylamide) and monomethoxy poly(ethylene glycol) grafts in water

The effects of SDS on the structural changes of the thermally induced polymeric micelles from a graft copolymer comprising poly(acrylic acid) (PAAc) as the backbone and poly(N-isopropylacrylamide) (PNIPAAm) and monomethoxy poly(ethylene glycol) (mPEG) as the grafts in aqueous solution are studied. At low temperature, SDS micelles form via the hydrophobic association of SDS molecules with the PNIPAAm grafts at a critical aggregation concentration of SDS (cac(SDS)) much lower than its critical micelle concentration. Consequently, the critical aggregation temperature of the graft copolymer is elevated. The corresponding structure of the thermally induced polymeric micelles is characterized by an abrupt reduction in the particle size and an increased tendency toward formation of the monocore structure with a more compact and hydrophobic PNIPAAm microdomain being developed. On the other hand, upon the polymeric micelle formation at high temperature, the copolymer-bound SDS micelle structure is disrupted and the dissociated SDS molecules migrate to the core-shell interface with their alkyl chains residing in the liquidlike region of the hydrophobic PNIPAAm microdomain. The correlation between the polymeric particles and copolymer-bound micelles is further substantiated by showing the change of the colloidal particle size in response to changes in cac(SDS) via adjusting the pH of the aqueous copolymer/SDS solutions.     

Synthesis and properties of poly(ethylene oxide)‐grafted polyethylene copolymer and terpolymer

A series of graft copolymers were synthesized based on ethylene‐co‐m,p‐methylstyrene (EMS) (backbone copolymer), ethylene‐1‐hexene‐m,p‐methylstyrene (EHMS) (backbone terpolymer), and polyethylene glycol monomethyl ethers (PEGM) (grafts) in this study. The PEGMs with molecular weights of 750 and 2000 were used. The chemical composition of the graft copolymers was analyzed by NMR and DSC measurements. The graft copolymers exhibited a phase‐separated morphology with the backbone and the methoxy polyethylene glycol (MPEG) grafts forming separate crystalline phases. The MPEG phase had a melting temperature lower than the corresponding MPEG homopolymer, as determined by DSC. The melting point of the crystalline phase formed by the EMS and EHMS main chains was lower than that of pure polymer backbone. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of anionic graft copolymers containing poly(ethylene oxide) grafts

Anionic graft copolymers were synthesized through grafting of poly(ethylene glycol) monomethyl ether (MPEG) onto terpolymers containing succicinic anhydride groups. The backbone polymers were prepared through radical terpolymerization of maleic anhydride, styrene, and one of the following monomers: methyl methacrylate, ethylhexyl methacrylate, and diethyl fumarate. MPEG of different molecular weights were grafted onto the backbone through reactions with the cyclic anhydride groups. In this reaction one carboxylic acid group is formed together with each ester bond. The molecular weights of MPEG were found to influence the rate of the grafting reaction and the final degree of conversion. The graft copolymers were characterized by IR, GPC, and ¹H-NMR. Thermal properties were examined by DSC. Graft copolymers containing 50% w/w of MPEG 2000 grafts were found to be almost completely amorphous, presumably because of crosslinking, and hydrogen bonding between carboxylic acid groups in the backbone and the ether oxygens in MPEG grafts. © 1995 John Wiley & Sons, Inc.     

An Efficient Approach for Preparing Giant Polypeptide Triblock Copolymers by Protein Dimerization

An efficient and convenient approach for preparing a giant polypeptide–poly(ethylene oxide) triblock copolymer architecture of defined structure and composition is reported. This copolymer consists of two long polypeptide chains derived from bovine serum albumin of distinct lengths with stabilizing poly(ethylene oxide) side‐chains, a connecting poly(ethylene oxide) block, and the presence of secondary structure elements along the polypeptide backbone. It is synthesized from the abundant plasma protein serum albumin and the polypeptide backbone is fully biodegradable. This approach represents a convenient and efficient strategy for preparing giant polypeptide‐based block copolymers of defined structure via a semi‐synthetic strategy. Such high‐molecular‐weight, biodegradable copolymers are attractive for various biomedical applications     

Synthesis and characterization of model block-graft copolymers via anionic polymerization: Introduction of poly(isoprene) and poly(ethylene oxide) as graft chains

New architectural graft copolymers were prepared, that is, the graft chains were situated in terminal or center position of the backbone chain. These graft copolymers were termed block-graft copolymers. Two different block-graft copolymers were prepared from a “grafting onto” process and a “grafting from” process via living anionic polymerization. These backbone chains are poly(styrene), and the graft chains are poly(isoprene) and poly(ethylene oxide). The polymers were characterized by GPC measurements, osmometry, and ultracentrifugation. The block-graft copolymers formed fine microphase separation structures. It was a morphological feature that an apparent volume fraction of the graft to the backbone might be higher than the real volume fraction.     

Influencing the morphology of polymer blends through graft copolymers

Graft copolymers have a potential as compatibilizers in two-component thermoplastic polymer blends, and also as impact-modifiers in one-component thermoplastics. The compatibility of the blocks of the copolymer (i.e. the grafts and the main chain) with the chains of the matrix polymers must be adjusted carefully. Blends of various polymers, especially of polystyrene (PS) and poly(vinyl chloride) (PVC), with graft copolymers on the basis of polybutadiene are discussed. An excellent compatibilizer, for blends PS/PVC, is a block-graft copolymer, derived from a diblock copolymer of Styrene and butadiene, with grafts of cyclohexyl methacrylate monomelic units.     

Two-dimensional ordered arrays of monodisperse silica particles grafted with concentrated polymer brushes

Hybrid particles which have a core of monodisperse silica particle and a shell of well-defined poly(methyl methacrylate) chains end-grafted on the core surface with a surface density as high as 0.8 chains/nm² were prepared by surface-initiated atom transfer radical polymerization of methyl methacrylate with an initiator-fixed silica particle. Monolayers of the hybrid particles were formed at the air-water interface by depositing a defined amount of the particle suspension onto water surface. Transmission electron microscopic and atomic force microscopic observations of these monolayers showed that the hybrid particles formed a two-dimensional hexagonally ordered lattice with a wide controllability of interparticle distance. This lattice structure was utilized as a template for the fabrication of a negatively patterned surface of poly(dimethylsiloxane) elastomer.     

Characterization of layer-by-layer self-assembled multilayer films of diblock copolymer micelles

The in situ layer-by-layer (LbL) self-assembly of low Tg diblock copolymer micelles onto a flat silica substrate is reported. The copolymers used here were a cationic poly(2-(dimethylamino)ethyl methacrylate)-block-poly(2-(diethylamino)ethyl methacrylate) (50qPDMA-PDEA; 50q refers to a mean degree of quaternization of 50 mol % for the PDMA block) and zwitterionic poly(methacrylic acid)-block-poly(2-(diethylamino)ethyl methacrylate) (PMAA-PDEA), which has anionic character at pH 9. Alternate deposition of micelles formed by these two copolymers onto a silica substrate at pH 9 was examined. The in situ LbL buildup of the copolymer micelle films was monitored using zeta potential measurements, optical reflectometry, and a quartz crystal microbalance with dissipation monitoring (QCM-D). For a six layer deposition, complete charge reversal was observed after the addition of each layer. The OR data indicated clearly an increase in adsorbed mass with each additional micelle layer and suggest that some interdiffusion of copolymer chains between layers and/or an increase in the film roughness, and hence in the effective surface area of the micellar multilayers, must take place as the film is built up. QCM-D data indicated that the self-assembled micellar multilayers on a flat silica substrate undergo structural changes over a prolonged period. This is attributed to longer-term interdiffusion of the copolymer chains between the outer two layers after the initial adsorption of each layer is complete. The QCM-D data further suggest that the outer adsorbed layers adopt a progressively more extended conformation, particularly for the higher numbered layers. The morphology of each successive layer was characterized using in situ soft-contact atomic force microscopy, and micelle-like surface aggregates are clearly observed within each layer of the complex film, suggesting the persistence of aggregate structures throughout the multilayer structure.     

Synthesis and bulk assembly behavior of linear–dendritic rod diblock copolymers

Dendritic rod structures can be formed via the branching of dendritic elements from a primary polymer backbone; such systems present an opportunity to create nanoscale material structures with highly functional exterior regions. In this work, we report for the first time the synthesis of a hybrid diblock copolymer possessing a linear–dendritic rod architecture. These block copolymers consist of a linear poly(ethylene oxide)–poly(ethylene imine) diblock copolymer around which poly(amido amine) branches have been divergently synthesized from the poly(ethylene imine) block. The dendritic branches are terminated with amine or ester groups for the full generations and half‐generations, respectively; however, the methyl ester terminal groups can also be readily converted into alkyl groups of various lengths, and this allows us to tune the hydrophilic/hydrophobic nature of the dendritic block and, therefore, the amphiphilic properties of the diblock copolymer and its tendencies toward microphase separation. The block copolymers exhibit semicrystallinity due to the presence of the poly(ethylene oxide) block; however, as the polymer fraction consisting of poly(ethylene oxide) decreases, the overall crystallinity also decreases, and it approaches zero at generation 2.0 and higher. The unfunctionalized block copolymers show weak phase segregation in transmission electron microscopy and differential scanning calorimetry at all generations. The addition of n‐alkyl chains increases phase segregation, particularly at high alkyl lengths. The generation 3.5 polymer with n‐dodecyl alkyl substitution has a rodlike or wormlike morphology consisting of domains of 4.1 nm, equivalent to the estimated cross section of the individual polymer chains. In this case, the nanometer scale of the polymer chains can be directly observed with transmission electron microscopy. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2784–2814, 2004     

Complex,degradable polyester materials via ketoxime ether‐based functionalization: Amphiphilic,multifunctional graft copolymers and their resulting solution‐state aggregates

Degradable, amphiphilic graft copolymers of poly(ε‐caprolactone)‐graft‐poly(ethylene oxide), PCL‐g‐PEO, were synthesized via a grafting onto strategy taking advantage of the ketones presented along the backbone of the statistical copolymer poly(ε‐caprolactone)‐co‐(2‐oxepane‐1,5‐dione), (PCL‐co‐OPD). Through the formation of stable ketoxime ether linkages, 3 kDa PEO grafts and p‐methoxybenzyl side chains were incorporated onto the polyester backbone with a high degree of fidelity and efficiency, as verified by NMR spectroscopies and GPC analysis (90% grafting efficiency in some cases). The resulting block graft copolymers displayed significant thermal differences, specifically a depression in the observed melting transition temperature, T_m, in comparison with the parent PCL and PEO polymers. These amphiphilic block graft copolymers undergo self‐assembly in aqueous solution with the P(CL‐co‐OPD‐co‐(OPD‐g‐PEO)) polymer forming spherical micelles and a P(CL‐co‐OPD‐co‐(OPD‐g‐PEO)‐co‐(OPD‐g‐pMeOBn)) forming cylindrical or rod‐like micelles, as observed by transmission electron microscopy and atomic force microscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3553–3563, 2010     

Comparison of the adsorption of cationic diblock copolymer micelles from aqueous solution onto mica and silica

The similarities and differences in the adsorption behavior of diblock poly(2-(dimethylamino)ethyl methacrylate)-b-poly(2-(diethylamino)ethyl methacrylate) (XqPDMA-PDEA, where X refers to a mean degree of quaternization of the PDMA of either 0, 10, 50, or 100 mol%) copolymers at the mica/ and silica/aqueous solution interfaces have been investigated. These diblock copolymers form core-shell micelles with the PDEA chains located in the cores and the more hydrophilic PDMA chains forming the cationic micelle coronas at pH 9. These micelles adsorb strongly onto both mica and silica due to electrostatic interactions. In situ atomic force microscopy (AFM) has demonstrated that the mean spacing and the dimension of the adsorbed micelles depend on both the substrate and the mean degree of quaternization of the PDMA blocks. In particular, the morphology of the adsorbed nonquaternized 0qPDMA-PDEA copolymer micelles is clearly influenced by the substrate type: these micelles form a disordered layer on silica, while much more close-packed, highly ordered layers are obtained on mica. The key reasons for this difference are suggested to be the ease of lateral rearrangement for the copolymer micelles attached to the solid substrates and the relative rates of relaxation of the coronal PDMA chains.