Highly dynamic and versatile pulsed fiber amplifier seeded?by?a?superluminescence diode

We propose and investigate a high power superluminescence diode (SLD) as a pulsed seed source for a highly dynamic and versatile pulse fiber amplifier system. The SLD provides, contrary to conventional Fabry?CPérot laser diodes, a smooth and broad output spectrum which is independent of the input pulse parameters. The output pulses from the SLD are as short as 10?ns with up to 150?mW peak power. Moreover, the pulses can be directly shaped by modulating the injection current of the SLD. Pulse shaping in an amplifier configuration is demonstrated without the observation of stimulated Brillouin scattering (SBS) due to the provided spectral bandwidth of 10?nm FWHM. Further spectral shaping was realized with a band pass filter in the amplifier chain.     

kJ级宽带低相干激光驱动装置

激光等离子体相互作用的不稳定性将有望通过降低高功率激光装置输出光束的相干性得到大幅缓解。利用低相干光源作为种子源，采用钕玻璃放大介质，研制成功国际首台kJ级大带宽低相干激光装置，实现了带宽13 nm、能量960 J、脉宽3～10 ns可调，相干时间仅为300 fs的大能量光脉冲输出。输出脉冲光谱匀滑无纵模结构，且谱相位随机分布，可实现脉冲波形和光谱分布的无关联精密调控。该装置不仅成功演示验证了低相干激光驱动器的单元技术及系统集成技术，同时也为激光等离子体相互作用及高能量密度物理研究提供了全新的实验研究平台。     

Broadband spectral shaping in a Ti:sapphire regenerative amplifier

A birefringent crystal quartz plate of known thickness has been used as a spectral filter for spectral shaping in a Ti:sapphire regenerative amplifier. The spectral profile of the amplified pulse ejected from the regenerative amplifier was observed while adjusting the birefringent crystal plate in the cavity. By altering the gain spectrum, the bandwidth of the regeneratively amplified pulse was increased from 18 to 35 nm by using a 0.34-mm thick birefringent plate. The output pulse spectrum from the regenerative amplifier neared the bandwidth of the seed pulse. As a comparison, we used a coated filter outside the regenerative amplifier cavity, and the bandwidth of the regeneratively amplified pulse was stretched to 28 nm. When the bandwidth was stretched to 35 nm, the pulse was compressed to 35 fs.     

高能量环形长腔再生放大啁啾脉冲激光的研究

介绍了一种新型的高能量环形长腔再生放大器, 通过对谐振腔的模式分布进行计算, 建立了腔长为12 m的环形腔再生放大器, 在150 mJ的抽运能量下, 得到了单脉冲能量为20 mJ的放大激光输出, 对应的转化效率为13.3%, 其输出激光的能量远远超过了常规的再生放大器输出激光的单脉冲量. 放大激光的输出光谱为30 nm, 可以支持<40 fs的傅里叶转换极限脉宽. 关键词： 环形腔 再生放大 高能量     

滤波对8字腔掺铒光纤激光器锁模运转的影响

构建了基于损耗非对称非线性光学环镜的8字腔掺铒光纤锁模激光器,并讨论了腔内滤波带宽对腔内脉冲演化和激光器输出特性的影响.在非线性光学环镜中引入双向输出耦合器,耦合器和传输光纤位置的不对称产生非互易性,实现锁模运转.利用自制的可调谐滤波器实验研究了滤波带宽对激光器的影响.当滤波带宽为2.1 nm时,腔内脉冲的演化过程受滤波和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲半高全宽分别为583.7fs和2.94 ps.随着滤波带宽增大,滤波的作用逐渐减弱,激光器两路输出脉冲参数逐渐接近,并接近傅里叶变换极限脉冲.当滤波带宽较大时,腔内脉冲的演化过程受增益谱和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲均为变换极限脉冲,半高全宽约为440 fs.通过调节滤波器中心波长实现了对激光器输出脉冲光谱的连续调谐,调节范围大于30 nm.     

高功率固体激光性能仿真模型

为实现高功率固体激光装置的能量平衡和功率平衡,开发了激光性能仿真模型为神光-Ⅲ原型装置的运行提供实时预测。模型能够确定系统参数设置(注入能量、注入脉冲波形和参数诊断衰减设置等)。注入能量的预测采用基于以往实验数据的放大曲线拟合方法。平顶脉冲的注入波形预测采用循环迭代算法,整形脉冲波形的预测采用增益-通量曲线法。参数诊断衰减设置是通过基于SG99光传输放大模型的全光路模拟计算实现。对原型装置的仿真表明,能量预测偏差在5%以内; 基频光束间能量分散度可控制在10%以内。模型已成为神光-Ⅲ原型装置运行仿真的有效工具。     

基于大基模体积的10mJ飞秒钛宝石激光再生放大器

文章报导了基于大基模体积的高能量飞秒钛宝石激光再生放大器的设计与实验研究,在重复频率10 Hz、抽运能量60 mJ的激励下,得到了单脉冲能量17.4 mJ的种子脉冲放大结果,压缩后的脉冲宽度为40.6 fs,能量为13.9 mJ.借助于此大基模体积再生腔,仅增加一级多通放大,实现了峰值功率达1.9 TW飞秒激光脉冲输出.结果表明,大模体积再生放大不仅降低了后续放大对抽运能量的要求,也可以单独压缩实现再生腔直接输出10 mJ量级的飞秒激光脉冲,是大能量高峰值功率飞秒激光系统的优质前端.     

52 mJ narrow-bandwidth degenerated optical parametric system with a large-aperture periodically poled MgO:LiNbO3 device

We have demonstrated efficient, high-energy, narrow-spectral-bandwidth 2.128 microm pulse generation by use of periodically poled MgO:LiNbO3 devices with a 36 mm length and a 5 mm x 5 mm large aperture. A free-running degenerated optical parametric oscillator (OPO) pumped with a Q-switched 1.064 microm Nd:YAG laser exhibits a high slope efficiency of 75% and an optical-to-optical conversion efficiency of 70% with a broad spectral bandwidth (>100 nm). In a configuration with a spectrally narrowed master oscillator followed by a power amplifier, we have achieved an output pulse energy of 52 mJ with a spectral bandwidth of less than 2 nm at the degeneracy point. The total optical-to-optical conversion efficiency of the system reached 50%.     

采用环形再生腔结构的飞秒激光啁啾脉冲放大研究

采用环形再生腔结构的啁啾脉冲放大技术方案, 在重复频率100 Hz,单脉冲能量33.1 mJ的532 nm激光抽运下, 从钛宝石激光中获得了单脉冲能量9.84 mJ的放大输出, 对应的斜效率达33.1%.在重复频率10 Hz的情况下, 同样获得了单脉冲能量为9.64 mJ, 对应斜效率达36.8%的高效率放大结果. 通过色散补偿压缩该啁啾激光脉冲后的单脉冲能量为6.36 mJ, 脉冲宽度为59.7 fs. 测量结果表明典型的能量不稳定度为1.85%. 关键词： 啁啾脉冲放大 再生放大 飞秒激光 环形腔     

基于铌酸锂双折射晶体的皮秒拍瓦激光系统光谱整形

为补偿皮秒拍瓦激光系统中钕玻璃宽带放大引起的增益窄化,提出了一种基于铌酸锂双折射晶体的高能量光谱整形方法.在相同强度调制下,对比了BBO、铌酸锂和石英3种晶体,针对1053 nm激光,选用了高双折射率、大口径且不易潮解的铌酸锂作为整形晶体.理论分析了晶体厚度、倾斜角、面内旋转角对强度调制的影响,发现它们分别决定调制的带宽、中心波长及深度.并对整形过程中晶体引入的光谱相位进行了分析,发现各阶色散量随晶体厚度、倾斜角、面内旋转角变化的规律,因此可通过上述参数控制各阶色散量.在此基础上,开展了中心波长为1053 nm、带宽为10 nm、调制深度为80%的光谱整形实验和相位测量实验,实验与理论分析相一致.针对神光Ⅱ皮秒拍瓦激光系统,利用上述整形方案,国内首次实现了1700 J, 6 nm (FWHM)的高能宽带激光输出,有效补偿了增益窄化.研究结果对国内基于钕玻璃放大系统的宽频带激光装置的工程研制具有重要意义.     

高功率超短脉冲激光系统中用AOPDF实现增益窄化补偿的实验研究

超短脉冲激光系统中，足够宽的带宽是获得超短脉冲的先决条件.高增益放大器，特别是再 生放大器的增益窄化效应严重制约着输出激光脉冲的时间特性.将可编程声光色散滤波器(AO PDF)应用到高功率激光系统中，能有效地克服增益窄化效应.实验表明，再生放大器的光谱 宽度由未应用前的27?nm增加到了44?nm，压缩脉冲的宽度减小了一半，从而也使峰值功率 提高了一倍. 关键词： 超短脉冲 增益窄化 光谱整形 可编程声光色散滤波器     

利用光谱滤波器实现自启动的全光纤超短脉冲掺Yb3+光纤激光器

讨论了利用光谱滤波器实现自启动的被动锁模掺Yb³⁺光纤环形激光器的锁模机理,并研制出全光纤结构超短脉冲掺Yb³⁺光纤环形激光器.使用980 nm二极管激光器作为抽运源,高掺杂浓度掺Yb³⁺光纤作为增益介质.在净群速度色散为正的环形腔中加入光谱滤波器,抑制Yb³⁺离子在1030 nm强发射峰的同时,通过对啁啾脉冲的光谱滤波实现脉冲压缩.光谱滤波器与光纤非线性偏振旋转效应相结合,实现了激光器在1053 nm可自启动、十分稳定的锁模运转.激光器锁模阈值功率300 mW,平均斜率效率18.3%,最大输出功率53.07 mW,对应最大输出脉冲能量3.2 nJ.锁模光脉冲中心波长1053.6 nm,3 dB带宽10.84 nm,重复频率16.45 MHz.锁模脉冲宽度为皮秒量级,经腔外光栅对压缩至188 fs. 关键词： 3+光纤激光器')" href="#">掺Yb³⁺光纤激光器 自启动锁模 全光纤     

High-energy, narrow-bandwidth periodically poled Mg-doped LiNbO3 optical parametric oscillator with a volume Bragg grating

We have demonstrated a simple, high-energy, narrow spectral bandwidth optical parametric oscillator (OPO) by use of a large aperture periodically poled Mg-doped LiNbO(3) device with a volume Bragg grating (VBG). A free-running degenerate OPO pumped by a Q-switched 1.064 microm Nd:YAG laser exhibits maximum output pulse energy of 110 mJ with high slope efficiency of 75% around room temperature. Broad spectral bandwidth (Dlambda~100 nm) around the degeneracy wavelength was suppressed by using a VBG as an output coupler. Up to 61 mJ of the output pulse energy with narrowed spectral bandwidth of less than 1.4 nm was obtained at the degeneracy wavelength of 2.128 microm.     

Broad-band regenerative laser amplification in ytterbium-doped calcium fluoride (Yb:CaF<Subscript>2</Subscript>)

An output pulse energy of 17.3 mJ has been achieved with a diode-pumped Yb:CaF₂ regenerative laser amplifier. The bandwidth of the output pulse spectrum was 7.3 nm, being seeded with femtosecond pulses stretched to 2.2 ns. In cw operation a tuning range of 80 nm has been observed. A maximum pulse energy of 44 mJ at a repetition rate of 1 Hz has been obtained in Q-switched mode. The laser damage threshold of a Yb:CaF₂ crystal has been determined at a wavelength of 1064 nm and a pulse duration of 10 ns. PACS 42.55.Ah; 42.55.Xi; 42.70.Hj     

On the generation of temporally shaped laser pulses for inertial confinement

Pulse shaping of some form is likely to be essential for laser fusion. The problems encountered in amplifying such pulses in present-day laser systems are studied in a computer model. Saturation effects in the amplifiers can significantly alter the input pulse shape. This pulse shape modification sets in when the output flux in the final amplifier reaches ≈ 15% of the saturation flux. Consequently, great flexibility is required for the pulse shaping mechanism if pulses of complex shapes are to be obtained at the output of a large laser amplifier systems. The problems have been simulated and analyzed for one beam line of the University of Rochester's planned 24 beam phosphate glass laser systems.     

Broadband high-energy diode-pumped Yb:KYW multipass amplifier

We report a diode-pumped Yb:KYW amplifier delivering up to 27 mJ pulses at a repetition rate of 100 Hz and a spectral bandwidth of 5.5 nm, centered at around 1030 nm. The system is based on a double-head multipass amplifier configuration where the pump thermal load is distributed over two relatively thin laser crystals, which permits a sufficiently large number of passes with minimal passive losses, thus maximizing the energy extraction efficiency. The amplified pulse bandwidth theoretically supports 340 fs pulses, and as a demonstration, a small fraction of the amplified pulses has been compressed to 560 fs.     

Spectral-Phase-Modulated Cross-Polarized Wave for Chirped Pulse Amplifier with High Contrast Ratio

We demonstrate a high-quality cross-polarized-wave filter based on spectral phase modulation. Driven by wellcompressed spectral-phase fully-compensated fundamental laser pulses, the filter stretches the pulse bandwidth from 35 nm to 70 nm with a conversion efficiency of 20%. After implementing the filter into a femtosecond TW Ti:sapphire laser system, we generate 40 mJ output pulse energy with pulse duration of 18.9 fs. The temporal contrast of the compressed pulse is enhanced to 10~9.     

高稳定激光脉冲波形精密调控技术研究与应用

提出了基于激光脉冲波形精密调控和能量稳定性控制的双回路同步闭环设计方法,进而在任意波形发生器与预放大系统输出处建立脉冲波形闭环控制系统,在保偏大模场光纤放大器和再生放大器间建立能量稳定性闭环系统。依托大口径高通量实验平台,实现了激光脉冲波形的快速高稳定精密调控,脉冲波形闭环精度优于2%（RMS）,脉冲能量稳定性优于5%（PV）。该技术成功应用到物理实验正式发射中,常规整形脉冲波形的功率准确度优于2%,相关结果有力支撑了ICF激光驱动器激光参数精密调控设计。     

滤波位置相关的全正色散掺Yb3+锁模光纤激光器的实验研究

采用非线性偏振旋转锁模,构建了一种全正色散掺Yb³⁺光纤环形激光器.在该激光腔内采用了10 nm带宽的光纤滤波器提供附加的自振幅调制.通过改变滤波器在腔内的位置,实验证明了滤波器位置对高啁啾脉冲的整形过程起到重要的作用.在320 mW的抽运功率下,最终获得平均功率为922 mW,脉冲重复频率为266 MHz,脉冲宽度为62 ps的稳定脉冲输出,单脉冲能量达35 nJ的优化结果.通过数值模拟与实验结果的验证表明,两者相符很好. 关键词： 锁模光纤激光器 全正色散 滤波效应 高啁啾脉冲     

无展宽器的高重复率钛宝石啁啾飞秒脉冲再生放大器的研究

通过优化放大腔结构参数和采用高光束质量的泵浦激光,依靠放大器腔内各个元件的色散展宽种子脉冲, 用钛宝石作为增益介质, 在低泵浦能量下, 实现了高光束质量,高稳定的中等能量的高重复率飞秒脉冲再生放大. 将钛宝石晶体离焦放置,有效的避免了光学损伤. 在1.1 mJ的绿光泵浦下, 获得了2 ps, 120 μJ, 重复频率为1 KHz, 光谱带宽7.8 nm的放大脉冲, 用石英棱镜对压缩可得到130 fs的激光脉冲.