Surface thermodynamics of binary mixtures of ethylene glycol + cyclohexanol or cyclopentanol

Surface tension data of binary mixtures of ethylene glycol + cyclohexanol and ethylene glycol + cyclopentanol was measured over the entire concentration range at various temperatures. The experimental values were correlated with temperature and with mole fraction. The values of the surface entropy, surface enthalpy and excess surface tension for these mixtures were also calculated.     

Micellisation thermodynamics of sodium lauroylsarcosinate in water–alcohol binary mixtures

Aggregation of sodium lauroylsarcosinate (SLS) in aqueous solutions of methanol, ethanol, propanol and ethylene glycol at 288–313 K has been determined from conductivity measurement in the range 0–20% v/v of additives. The precise values of the critical micelle concentration (CMC) and the degree of counter-ion dissociation of micelles were obtained at each temperature by fitting the specific conductivity-surfactant concentration curve to the integrated form of the Boltzmann-sigmoid equation. The CMC was found to increase with increase in additive concentrations in the case of methanol and ethylene glycol, while it decreases with increase in ethanol and propanol concentration. The equilibrium model of micelle formation was applied to obtain the thermodynamic parameters of micellisation. The Gibbs free energies were observed to vary only slightly with temperature and additive concentrations. Enthalpy–entropy compensation was observed for all the systems with a constant compensation temperature of ≈300 K and negative compensation enthalpy.     

Covalent grafting of ethylene glycol and glycerol into brucite

Layered brucite was synthesized at room temperature and, after characterization, was reacted in a closed flask with either ethylene glycol or glycerol. Powder X-ray diffraction patterns have shown that new compounds with interlayer expansions were obtained. New bands attributed to grafting of ethylene glycol and glycerol into the interlayer surface of brucite were detected by FTIR. XPS spectroscopy and thermal analyses (TG/DSC) have shown that nearly all of the hydroxide groups of the layers were replaced by either ethylene glycol or glycerol through Mg-O-C bonds.     

Characterization of low-fouling ethylene glycol containing plasma polymer films

Low-protein-fouling poly(ethylene glycol) (PEG-like) plasma polymer films were prepared using radio frequency glow discharge polymerization of diethylene glycol dimethyl ether (DGpp) on top of a heptylamine plasma polymer primer layer. By varying the plasma deposition conditions, the chemistry of the DGpp film was influenced, especially in regard to the level of ether content, which in turn influenced the relative levels of bovine serum albumin and lysozyme protein fouling. Surface potential measurements indicated that these surfaces carried a net negative charge. While protein fouling remained low ( approximately 10 ng/cm2), there was a slightly higher level of the positively charged protein adsorbed on these films than the negative protein. The interaction forces measured between a silica spherical surface on both "high"- and "low"-protein-fouling DGpp films were all repulsive and short ranged (2-3 nm). There was no correlation between the surface forces measured for high- and low-protein-fouling DGpp films. Thus, it appears that enthalpic effects are very important in reducing protein adsorption. We therefore conclude that it is the concentration of residual, ethylene glycol containing species that are the crucial parameter determining protein resistance due to a combination of both entropic and enthalpic effects.     

Equilibrium Phase Behavior of Ethylene Glycol/Glycerin＋RbNO3/CsNO3＋H2O at 288.15 and 298.15 K

The solubilities, densities and refractive indices for the four ternary systems ethylene glycol/glycerin＋ RbNOJCsNO3＋H20 were measured with mass fractions of ethylene glycol or glycerin in a range of 0 to 1.0 at 288.15 and 298.15 K. In all the cases, the presence of either ethylene glycol or glycerin significantly reduces the solubilities of the rubidium nitrate and cesium nitrate in aqueous solution, but the refractive indices increase with the increase of mass fraction of either ethylene glycol or glycerin. The density, refractive index and solubility of the saturated ternary systems were correlated with each other via polynomial equations. In addition, the refractive indices and densities of unsaturated solutions were also determined for the four ternary systems with different salt concentrations, which were correlated with the salt concentration and proportion of ethylene glycol or glycerin in the solution.     

Covalent Grafting of Ethylene Glycol into the Zn-Al-CO(3) Layered Double Hydroxide

Zn-Al-CO(3) layered double hydroxide was synthesized at room temperature using a procedure reported elsewhere. After characterization, 0.5 g of the Zn-Al-CO(3) layered compound was reacted under air with 15 cm(3) of ethylene glycol at 80 degrees C for a period of 5 days. After washing with acetone and drying at 50 degrees C, the resulting white powder was characterized by X-ray powder diffraction, thermal analysis (simultaneous TG/DSC), elemental analysis (C, H, N, Al, and Zn content), and FTIR spectroscopy. All of the experimental data were consistent with the bidentade grafting of ethylene glycol into the interlayer surface of the Al-Zn double hydroxide. The stoichiometry obtained [Zn(0.66)Al(0.34)(OCH(2)CH(2)O)](OH)(0.34).0.4H(2)O] showed that all of the surface hydroxide groups were replaced by ethylene glycol through Al-(Zn)-O-C bonds. Carbonate could not be detected by FTIR, proving that OH(-) was probably the actual intercalated counteranion. Copyright 2000 Academic Press.     

Langmuir-Blodgett films composed of amphiphilic double-decker shaped polyhedral oligomeric silsesquioxanes

New amphiphilic polyhedral oligomeric silsesquioxanes (POSSs) were synthesized, and their monolayer behavior on a water surface and Langmuir-Blodgett (LB) film formation were studied. Two kinds of amphiphilic POSS molecules, which have two or four di(ethylene glycol) units (2OH-DDSQ and 4OH-DDSQ, respectively), were synthesized by direct hydrosilylation of di(ethylene glycol) vinyl ether with double-decker shaped polyhedral oligomeric silsesquioxanes (DDSQs). Surface pressure (π)-area (A) isotherms and Brewster angle microscope (BAM) measurements indicated that both amphiphilic DDSQs form a stable monolayer at the air-water interface. In addition, 4OH-DDSQ can be deposited on a solid substrate by the LB technique. Atomic force microscope (AFM) images of a one-layer 4OH-DDSQ film showed a homogenous uniform surface on a hydrophilic silicon substrate, whereas nanometer scale dots were formed on a hydrophobic silicon substrate. Multilayer deposition on a hydrophobic substrate resulted in an increase of dot size with increasing deposition number of layers. Moreover, homogenous multilayer films with a few voids were obtained on a hydrophilic substrate. The results indicate that 4OH-DDSQ is a good candidate for preparing hybrid nanoassemblies.     

Effect of ethylene glycol on the thermodynamic and micellar properties of Tween 20

The aggregation behaviour of Tween 20 in ethylene glycol-water mixed solvents has been investigated using surface tension, density, static and dynamic light scattering, and fluorescence measurements. Micellar and surface thermodynamics data were obtained from the temperature dependence of critical micelle concentrations in various aqueous mixtures of ethylene glycol. In order to evaluate the influence of the cosolvent, the differences in the Gibbs energies of micellization of Tween 20 between water and binary solvents were determined. This study allowed us to conclude that the ability of ethylene glycol to act as a structure breaker and its interaction with the surfactant hydrophilic group are the controlling factors of the micellization process. From the evaluation of the thermodynamics of adsorption at the solution-air interface, it was determined that the surface activity of the surfactant decreases slightly with increasing concentration of ethylene glycol at a given temperature. Partial specific volume data, obtained by density measurements, indicate that the fraction of solvent molecules interacting with the micelle, via hydrogen bonds, remained roughly constant. The effect of cosolvent on the size and solvation of the aggregates was analysed by means of static and dynamic light scattering measurements. It was found that the aggregation number decreased, whereas the whole micellar solvation increased with the ethylene glycol content. Micellar micropolarity was examined using two different probes, pyrene and 8-anilinonaphthelene-1-sulfonic acid, and was found to increase with ethylene glycol addition, accompanied by an enhanced solvation. Fluorescence polarization measurements found by using coumarin 6 as a hydrophobic probe revealed an increase in the micellar microviscosity. The observed trends in these microenvironmental properties were ascribed to a participation by ethylene glycol in the micellar solvation layer.     

Excess thermodynamic functions derived from densities and surface tensions of (p- or o-xylene + ethylene glycol dimethyl ether) between the temperatures (298.15 and 308.15) K

Densities (ρ) for binary systems of (p-xylene or o-xylene + ethylene glycol dimethyl ether) were measured over the full mole fraction range at the temperatures of (298.15, 303.15 and 308.15) K along with the densities of the pure components. The excess molar volumes (V^E) calculated from the density data show that the deviations from ideal behaviour in the two binary systems are negative, and they become more negative with the temperature increasing. Surface tensions (σ) of these binary systems were determined at the same temperatures (298.15, 303.15 and 308.15) K by the pendant drop method. The surface tension deviations (δσ) for p-xylene system are negative over the whole composition range, and become less negative with the temperature increasing, but for the o-xylene system, δσ are negative at high o-xylene concentration, and change to positive with the o-xylene concentration decreasing. The V^E and δσ were fitted to the Redlich–Kister polynomial equation. Surface tensions were also used to estimate surface entropy (S_σ) and surface enthalpy (H_σ).     

Immobilization of ethylenesulfide on silica surface using acid and base catalysts Adsorption and thermodynamic data

The reaction of cyclic ethylene sulfide with 3-aminopropyltrimethoxysilane resulted in a new silylating agent, which was anchored onto a silica surface via the sol-gel procedure using hydrochloric acid or ammonium hydroxide as acid or base catalysts, respectively. Both organofunctionalized surfaces have the ability to adsorb divalent cations from aqueous nitrate solution. Through calorimetric titrations, the thermodynamic data of cation-basic center interactions were obtained. Exothermic enthalpy values were obtained for all interaction processes. The calculated free Gibbs energy is in agreement with the spontaneity of the reactions and the positive entropy values for all reactions are favorable for these systems.     

Thermodynamics of micellization of tetradecyltrimethylammonium bromide in ethylene glycol–water binary mixtures

The aggregation behaviour of tetradecyltrimethylammonium bromide in ethylene glycol–water mixtures across a range of temperatures has been investigated by electrical conductivity measurements. The critical micelle concentration (cmc) and the degree of counterion dissociation of micelles were obtained at each temperature from plots of differential conductivity, (κ/c) _{T , P} , versus the square root of the total concentration of the surfactant. This procedure not only enables us to determine the cmc values more precisely than the conventional method, based on plots of conductivity against total concentration of surfactant, but also allows straightforward determination of the limiting molar conductance and the molar conductance of micellar species. The equilibrium model of micelle formation was applied to obtain the thermodynamics parameters of micellization. Only small differences have been observed in the standard molar Gibbs free energies of micellization over the temperature range investigated. The enthalpy of micellization was found to be negative in all cases, and it showed a strong dependence on temperature in the ethylene glycol poor solvent system. An enthalpy–entropy compensation effect was observed for all the systems, but whereas the micellization of the surfactant in the solvent system with 20 wt% ethylene glycol seems to occur under the same structural conditions as in pure water, in ethylene glycol rich mixtures the results suggest that the lower aggregation of the surfactant is due to the minor cohesive energy of the solvent system in relation to water. Received: 13 December 1998 Accepted in revised form: 25 February 1999     

聚苯并咪唑-锂盐-聚乙二醇单甲醚共混全固态聚合物电解质的制备及性能

使用共混后浇铸成膜的方法,制备了聚苯并咪唑-锂盐-聚乙二醇单甲醚组成的锂离子电池共混全固态聚合物电解质。通过傅里叶红外光谱(FT-IR)、X射线衍射(XRD)、差示扫描量热(DSC)、拉伸与交流阻抗测试表征了共混全固态电解质的结构与性能。研究了不同锂盐以及各组分含量对共混全固态电解质的力学性能与电导率的影响。结果表明:聚苯并咪唑与聚乙二醇单甲醚之间存在氢键;共混全固态电解质中聚乙二醇单甲醚处于无定形态;锂盐的加入使聚乙二醇单甲醚的玻璃化转变温度下降;聚乙二醇单甲醚含量越高,共混膜强度越低,电导率越高,并且使用三氟甲磺酸锂作为锂盐时其电导率最高,室温下可以达到3.58×10~(-5) S/cm,高温下可以达到3.3×10~(-3) S/cm,高温下满足对锂离子电池的使用需求。     

Surface properties of diluted solutions of cyclohexanol and cyclopentanol in ethylene glycol

The surface tension, sigma, of dilute solutions of cyclohexanol and cyclopentanol in ethylene glycol was measured in the temperature range between 293.15 and 323.15 K by means of the ring detachment method. The surface entropies and enthalpies were calculated. The surface excess values were obtained using the Gibbs equation. The surface tension data were analyzed using the extended Langmuir (EL) model and the surface composition were obtained from this model. It was shown that clathrate-like solvates (hydrophobic-like solvation) are forming in the dilute solution of cyclohexanol in ethylene glycol.     

Effect of temperature on the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions

In this work the intrinsic viscosity of poly(ethylene glycol)/poly(vinyl pyrrolidone) blends in aqueous solutions were measured at 283.1–313.1 K. The expansion factor of polymer chain was calculated by use of the intrinsic viscosities data. The thermodynamic parameters of polymer solution (the entropy of dilution parameter, the heat of dilution parameter, theta temperature, polymer–solvent interaction parameter and second osmotic virial coefficient) were evaluated by temperature dependence of polymer chain expansion factor. The obtained thermodynamic parameters indicate that quality of water was decreased for solutions of poly(ethylene oxide), poly(vinyl pyrrolidone) and poly(ethylene oxide)/poly(vinyl pyrrolidone) blends by increasing temperature. Compatibility of poly(ethylene oxide)/poly(vinyl pyrrolidone) blends were explained in terms of difference between experimental and ideal intrinsic viscosity and solvent–polymer interaction parameter. The results indicate that the poly(ethylene glycol)/poly(vinyl pyrrolidone) blends were incompatible.     

Partial purification of glucose 6-phosphate dehydrogenase and phosphofructokinase from rat erythrocyte haemolysate by partitioning in aqueous two-phase systems

Glucose 6-phosphate dehydrogenase shows a high partition coefficient in poly-(ethylene glycol)-dextran aqueous two-phase systems in comparison with those for 6-phosphogluconate dehydrogenase, phosphofructokinase and the bulk of proteins present in rat erythrocyte haemolysates. As a consequence, fractions highly enriched in glucose 6-phosphate dehydrogenase can be obtained after multiple partitions in the above systems with a counter-current distribution procedure. Phosphofructokinase shows a high affinity for Cibacron Blue and, as a result, the enzyme can be extracted in the top phase of poly(ethylene glycol)-dextran systems containing Cibacron Blue-poly(ethylene glycol) (affinity systems). The efficiency for the purification of the enzymes by partitioning is increased up to 10-fold when enzyme-rich fractions, obtained by precipitation with poly(ethylene glycol), are used instead of original haemolysate. The recovery of enzyme activities is near 100% in both instances.     

Equilibrium study of polymer–polymer complexation of poly(methacrylic acid) and poly(acrylic acid) with complementary polymers through cooperative hydrogen bonding

The degree of linkage, θ, defined as the ratio of the binding groups to the total of potentially interacting groups and the stability constant K of the polymer–polymer complexes in the systems poly(methacrylic acid)–poly(ethylene glycol), poly(acrylic acid)–poly(ethylene glycol), and poly-(methacrylic acid)–poly(vinyl pyrrolidone) in aqueous and aqueous alcohol media were determined as a function of temperature by potentiometric titration. It was found that θ and K are strongly dependent on chain length, temperature, and medium and that hydrophobic interaction is a significant factor in the stabilization of the complexes. The enthalpy and entropy changes and the cooperativeness parameter of the systems were calculated. A mechanism for the complexation in terms of cooperative interaction was proposed.     

Entropy generation in nonlinear mixed convective flow of nanofluid in porous space influenced by Arrhenius activation energy and thermal radiation

This paper focuses on an experimental study of the surface tension of nanofluids based on ethylene glycol with various types of nitride nanoparticles. Samples were prepared using a two-step method with mass content between 1 and 5% of particles. Nanofluids contain three types of nitride nanoparticles: aluminum nitride, silicon nitride and titanium nitride with various particle average sizes. Surface tension of nanofluids was investigated at a constant temperature of 298.15 K with two different techniques: du Noüy ring method and pendant drop method. It is presented that experimental values obtained with both methods are in good agreement with each other. Also, results obtained during this study show that the addition of this type of nanoparticles does not have a significant impact on the surface tension of base fluid for the concentrations and diameters of nitride nanoparticles considered.

     

Competitive surface adsorption of solvent molecules and compactness of agglomeration in calcium hydroxide nanoparticles

Calcium hydroxide forms unstable reactive nanoparticles that are stabilized when they are dispersed in ethylene glycol or 2-propanol. The aggregation behavior of these particles was investigated by contrast-variation small-angle neutron scattering (SANS), combined with small-angle X-ray scattering (SAXS). Nanoparticles on the order of 100 nm were found to aggregate into mass-fractal superstructures in 2-propanol, while forming more compact agglomerated aggregates with surface fractal behavior in ethylene glycol. Commensurate specific surface areas evaluated at the Porod limit were more than an order of magnitude greater in 2-propanol (approximately 200 m2.g(-1)) than in ethylene glycol (approximately 7 m2.g(-1)). This profound microstructural evolution, observed in similar solvents, is shown to arise from competitive solvent adsorption. The composition of the first solvent layer on the particles is determined over the full range of mixed solvent compositions and is shown to follow a quantifiable thermodynamic equilibrium, determined via contrast-variation SANS, that favors ethylene glycol over 2-propanol in the surface layer by about 1.4 kJ.mol(-1) with respect to the bulk solvent composition.     

Effect of iodine-containing promoter on the catalytic activity of silver in the course of ethylene glycol oxidation

Surface morphology and catalytic properties of electrolytic silver crystals in partial oxidation of ethylene glycol into glyoxal were studied.