Polycyclic aromatic hydrocarbon analysis in different matrices of the marine environment

Polycyclic aromatic hydrocarbons (PAHs) were determined in marine samples of various types, i.e. seawater, sediment and mussel homogenate samples. The samples were spiked with standard PAH mixtures in both polar (acetonitrile) and non-polar (i-octane) solvents, then extracted. Extraction from seawater was performed by liquid/liquid extraction to hexane (LLE) and with solid phase extraction (SPE) discs. The water samples were filtered and unfiltered seawater, and redistilled water for comparison. The discs with PAHs adsorbed from water samples, and also the sediment and mussel homogenate samples, were extracted with acetonitrile by sonication. PAHs in the disc extracts and from the LLE were cleaned-up using TLC and next determined by GC/MS/IT (with ion-trap) and HPLC-DAD/UV. The analytical procedures were verified with deuterated PAH standard mixtures. The large differences in PAH recoveries (from 12 to 86% for sum, and from 3 to 135% for particular PAHs) do not depend solely on the type of matrix and analytical procedure applied (e.g. standard solvent, volume of evaporated sample), but also on the concentration and molecular structure of the analyte. Usually, only a fraction of each PAH content in the matrix is determined, depending on the particulate matter in seawater and the sorption properties of the solid matrix. The recoveries of deuterated PAHs are higher than those of non-deuterated compounds.     

Improved efficiency of extraction of polycyclic aromatic hydrocarbons (PAHs) from the National Institute of Standards and Technology (NIST) Standard Reference Material Diesel Particulate Matter (SRM 2975) using accelerated solvent extraction

The efficiency of extraction of polycyclic aromatic hydrocarbons (PAHs) with molecular masses of 252, 276, 278, 300, and 302 Da from standard reference material diesel particulate matter (SRM 2975) has been investigated using accelerated solvent extraction (ASE) with dichloromethane, toluene, methanol, and mixtures of toluene and methanol. Extraction of SRM 2975 using toluene/methanol (9:1, v/v) at maximum instrumental settings (200 °C, 20.7 MPa, and five extraction cycles) with 30-min extraction times resulted in the following elevations of the measured concentration when compared with the certified and reference concentrations reported by the National Institute of Standards and Technology (NIST): benzo[b]fluoranthene, 46%; benzo[k]fluoranthene, 137%; benzo[e]pyrene, 103%; benzo[a]pyrene, 1,570%; perylene, 37%; indeno[1,2,3-cd]pyrene, 41%; benzo[ghi]perylene, 163%; and coronene, 361%. The concentrations of the following PAHs were comparable to the reference values assigned by NIST: indeno[1,2,3-cd]fluoranthene, dibenz[a,h]anthracene, and picene. The measured concentration of dibenzo[a,e]-pyrene was lower than the information value reported by the NIST. The measured concentrations of other highly carcinogenic PAHs (dibenzo[a,l]pyrene, dibenzo[a,i]pyrene, and dibenzo[a,h]pyrene) in SRM 2975 are also reported. Comparison of measurements using the optimized ASE method and using similar conditions to those applied by the NIST for the assignment of PAH concentrations in SRM 2975 indicated that the higher values obtained in the present study were associated with more complete extraction of PAHs from the diesel particulate material. Re-extraction of the particulate samples demonstrated that the deuterated internal standards were more readily recovered than the native PAHs, which may explain the lower values reported by the NIST. The analytical results obtained in the study demonstrated that the efficient extraction of PAHs from SRM 2975 is a critical requirement for the accurate determination of PAHs with high molecular masses in this standard reference material and that the optimization of extraction conditions is essential to avoid underestimation of the PAH concentrations. The requirement is especially relevant to the human carcinogen benzo[a]pyrene, which is commonly used as an indicator of the carcinogenic risk presented by PAH mixtures.     

Determination of 252–302 Da and tentative identification of 316–376 Da polycyclic aromatic hydrocarbons in Standard Reference Materials 1649a Urban Dust and 1650b and 2975 Diesel Particulate Matter by accelerated solvent extraction–HPLC-GC-MS

We have assessed and compared the extraction recoveries of polycyclic aromatic hydrocarbons (PAHs) with molecular weights of 252, 276, 278, 300 and 302 from diesel particulate matter (PM) and urban air particles using ultrasonically assisted extraction and accelerated solvent extraction methods, and evaluated the effects of sample and treatment parameters. The results show that accelerated solvent extraction can extract PAHs more efficiently from diesel PM than ultrasonically assisted extraction. They also show that PAHs are more difficult to extract from diesel PM than from urban air particles. Using toluene and maximum instrumental settings (200 °C, 3,000 psi and five extraction cycles) with 30-min static extraction times > 85% of the analytes were estimated to be extracted from the diesel particles, but four extraction cycles with just 5-min static extraction times under these conditions seem to be sufficient to extract > 95% of the analytes from the urban air particles. The accelerated solvent extraction method was validated using the Standard Reference Materials (SRM) 1649a, Urban Dust, and SRM 2975 and SRM 1650a, Diesel Particulate Matter, from the US National Institute of Standards and Technology (NIST). PAH concentrations determined by on-line high-performance liquid chromatography–gas chromatography–mass spectrometry (HPLC-GC-MS) following the developed accelerated solvent extraction method were generally higher than the certified and reference NIST values and concentrations reported in the literature (e.g. the estimated concentration of benzo[a]pyrene in SRM 2975 was 15-fold higher than the NIST-certified value), probably because the extraction recoveries were higher than in previous studies. The developed accelerated solvent extraction method was used to analyse high molecular (HMW) weight PAHs (MW > 302) in the investigated SRMs, and more than 170 (SRM 1649a), 80 (SRM 1650b) and 60 (SRM 2975) potential high molecular weight PAHs were tentatively identified in them, with molecular weights (depending on the SRM sample analysed) of 316, 326, 328, 340, 342, 350, 352, 366, 374 and 376. This is, to our knowledge, the first study to tentatively report PAHs with molecular weights of 316, 326, 328, 342, 350, 352, 366 and 376 in diesel particulate matter. GC-MS chromatograms obtained in selected ion monitoring mode (extracted ions for the abovementioned m/z) and full-scan mass spectra of tentatively identified high molecular weight PAHs are shown in the Electronic supplementary material. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Determination of polycyclic aromatic hydrocarbons in marine sediments using a new ASE-SFE extraction technique

In order to determine PAHs in marine sediment samples by GC/MS(SIM) a new extraction approach of ASE-SFE was evaluated using combined accelerated solvent extraction (ASE, dynamic and static mode) and supercritical fluid extraction (SFE, dynamic mode) without further purification of the sample. The solvents used for ASE-SFE were methylene chloride and carbon dioxide. The recovery data, precision and accuracy of the whole method were evaluated statistically. The average recoveries of PAHs, based on deuterated internal standards were 77% for 2-3-ring PAHs, 85% for 4-ring PAHs, 88% for 5-ring PAHs and 97% for 6-ring PAHs. The extraction time required for the ASE-SFE technique was 30 min, which is longer than in the case of independent use of ASE and shorter compared to SFE. ASE-SFE recoveries of PAHs from SRM marine sediment are comparable for (2-3-ring, 4-ring PAHs) or higher (5-ring, 6-ring PAHs) than reported for the conventional extraction methods of ASE and SFE. Method detection limits of (MDL) were statistically estimated. MDL values obtained for 15 PAHs compounds vary between 0.06 ngg(-1) and 3.54 ngg(-1).     

Novel approach to microwave-assisted extraction and micro-solid-phase extraction from soil using graphite fibers as sorbent

A single-step extraction-cleanup procedure involving microwave-assisted extraction (MAE) and micro-solid-phase extraction (micro-SPE) has been developed for the analysis of polycyclic aromatic hydrocarbons (PAHs) from soil samples. Micro-SPE is a relatively new extraction procedure that makes use of a sorbent enclosed within a sealed polypropylene membrane envelope. In the present work, for the first time, graphite fiber was used as a sorbent material for extraction. MAE-micro-SPE was used to cleanup sediment samples and to extract and preconcentrate five PAHs in sediment samples prepared as slurries with addition of water. The best extraction conditions comprised of microwave heating at 50 degrees C for a duration of 20 min, and an elution (desorption) time of 5 min using acetonitrile with sonication. Using gas chromatography (GC)-flame ionization detection (FID), the limits of detection (LODs) of the PAHs ranged between 2.2 and 3.6 ng/g. With GC-mass spectrometry (MS), LODs were between 0.0017 and 0.0057 ng/g. The linear ranges were between 0.1 and 50 or 100 microg/g for GC-FID analysis, and 1 and 500 or 1000 ng/g for GC-MS analysis. Granular activated carbon was also used for the micro-SPE device but was found to be not as efficient in the PAH extraction. The MAE-micro-SPE method was successfully used for the extraction of PAHs in river and marine sediments, demonstrating its applicability to real environmental solid matrixes.     

Comparisons of soxhlet extraction, pressurized liquid extraction, supercritical fluid extraction and subcritical water extraction for environmental solids: recovery, selectivity and effects on sample matrix

Extractions of a polycyclic aromatic hydrocarbon (PAH)-contaminated soil from a former manufactured gas plant site were performed with a Soxhlet apparatus (18 h), by pressurized liquid extraction (PLE) (50 min at 100 degrees C), supercritical fluid extraction (SFE) (1 h at 150 degrees C with pure CO2), and subcritical water (1 h at 250 degrees C, or 30 min at 300 degrees C). Although minor differences in recoveries for some PAHs resulted from the different methods, quantitative agreement between all of the methods was generally good. However, the extract quality differed greatly. The organic solvent extracts (Soxhlet and PLE) were much darker, while the extracts from subcritical water (collected in toluene) were orange, and the extracts from SFE (collected in CH2Cl2) were light yellow. The organic solvent extracts also yielded more artifact peaks in the gas chromatography (GC)-mass spectrometry and GC-flame ionization detection chromatograms, especially compared to supercritical CO2. Based on elemental analysis (carbon and nitrogen) of the soil residues after each extraction, subcritical water, PLE, and Soxhlet extraction had poor selectivity for PAHs versus bulk soil organic matter (approximately 1/4 to 1/3 of the bulk soil organic matter was extracted along with the PAHs), while SFE with pure CO2 removed only 8% of the bulk organic matrix. Selectivities for different compound classes also vary with extraction method. Extraction of urban air particulate matter with organic solvents yields very high concentrations of n- and branched alkanes (approximately C18 to C30) from diesel exhaust as well as lower levels of PAHs, and no selectivity between the bulk alkanes and PAHs is obtained during organic solvent extraction. Some moderate selectivity with supercritical CO2 can be achieved by first extracting the bulk alkanes at mild conditions, followed by stronger conditions to extract the remaining PAHs, i.e., the least polar organics are the easiest organics to extract with pure CO2. In direct contrast, subcritical water prefers the more polar analytes, i.e., PAHs were efficiently extracted from urban air particulates at 250 degrees C, with little or no extraction of the alkanes. Finally, recent work has demonstrated that many pollutant molecules become "sequestered" as they age for decades in the environment (i.e., more tightly bound to soil particles and less available to organisms or transport). Therefore, it may be more important for an extraction method to only recover pollutant molecules that are environmentally-relevant, rather than the conventional attempts to extract all pollutant molecules regardless of how tightly bound they are to the soil or sediment matrix. Initial work comparing SFE extraction behavior using mild to strong conditions with bioremediation behavior of PAHs shows great promise to develop extraction methodology to measure environmentally-relevant concentrations of pollutants in addition to their total concentrations.     

Determination of polycyclic aromatic hydrocarbons in marine sediments using a new ASE-SFE extraction technique

In order to determine PAHs in marine sediment samples by GC/MS(SIM) a new extraction approach of ASE-SFE was evaluated using combined accelerated solvent extraction (ASE, dynamic and static mode) and supercritical fluid extraction (SFE, dynamic mode) without further purification of the sample. The solvents used for ASE-SFE were methylene chloride and carbon dioxide. The recovery data, precision and accuracy of the whole method were evaluated statistically. The average recoveries of PAHs, based on deuterated internal standards were 77% for 2–3-ring PAHs, 85% for 4-ring PAHs, 88% for ¶5-ring PAHs and 97% for 6-ring PAHs. The extraction time required for the ASE-SFE technique was 30 min, which is longer than in the case of independent use of ASE and shorter compared to SFE. ASE-SFE recoveries of PAHs from SRM marine sediment are comparable for (2–3-ring, 4-ring PAHs) or higher (5-ring, 6-ring PAHs) than reported for the conventional extraction methods of ASE and SFE. Method detection limits of (MDL) were statistically estimated. MDL values obtained for 15 PAHs compounds vary between 0.06 ngg^?1 and 3.54 ngg^?1.     

Rapid determination of PAHs in soil samples by HPLC with fluorimetric detection following sonication extraction

A rapid method for the determination of PAHs in soil samples based on their extraction with methylene chloride by sonication and subsequent separation by HPLC with fluorimetric detection is proposed. A Hypersil Green PAH column was used with a gradient of acetonitrile/water as the mobile phase, together with a program of nine excitation and emission wavelength pairs. Recoveries were in the range 70-98%, except for acenaphthene and naphthalene, at concentration levels 1.08-442 microg/kg with relative standard deviations in the range 2-15% (n = 4). Total PAHs found in soil samples were in the range 15-282 microg/kg. The results were compared with those obtained by applying the 3540 EPA method for two samples.     

Magnetic solid-phase extraction of hydrophobic analytes in environmental samples by a surface hydrophilic carbon-ferromagnetic nanocomposite

A new sorbent of carbon-ferromagnetic nanocomposite was proposed for the extraction of polycyclic aromatic hydrocarbons (PAHs) in environmental samples. The sorbent was specially designed with a hydrophobic sublayer and a hydrophilic surface, which endows the sorbent some unique features. The former shows high extraction capability for the PAHs and the latter provides benign compatibility with the sample matrix. The sorbent can be easily dispersed in aqueous solutions for extraction and no additional stirring or shaking was necessary to facilitate the dispersion, which may bring operational convenience especially for on-site sampling and extraction. Parameters affecting the extraction efficiency were investigated in detail. The optimal conditions were as follows: 10mg of nanoparticles, 40mmol/L of sodium chloride, 30min of extraction time without shaking, hexane as the desorption solvent and 15min as the desorption-sonication time. The results demonstrate that enrichment factors ranging from 35- to 133-fold were obtained for the analytes. The limits of detection and the limits of quantification are in the range of 0.015-0.335ng/mL and 0.05-1.14ng/mL, respectively. Finally, the new sorbent was successfully used for the extraction of PAHs in lake water samples.     

Optimization and validation of a low temperature microwave-assisted extraction method for analysis of polycyclic aromatic hydrocarbons in airborne particulate matter

A low temperature microwave-assisted extraction method (MAE) is reported for the analysis of polycyclic aromatic hydrocarbons (PAHs) in airborne particulate matter (PM). The main parameters affecting the extraction efficiency (choice of extractants, microwave power, and extraction time) were investigated and optimized. The optimized procedure requires a 20 ml mixture of acetone:n-hexane (1:1) for extraction of PAHs in PM at 150 W of microwave energy (20 min extraction time). Clean-up of MAE extracts was not found to be necessary. The optimized method was validated using two different SRM (1648-urban particulate matter and 1649a, urban dust). The results obtained are in good agreement with certified values. PAHs recoveries for both reference materials were between 79 and 122% with relative standard deviation ranging from 3 to 21%. Detection limits were determined based on blank determination using two kinds of quartz filter substrates (n = 10), which ranged from 0.001 (0.03) ng m⁻³ (pg/μg) for B(k)Ft to 1.119 (37.3) for Naph in ng m⁻³ (pg/μg), respectively. The repeatability and day-to-day reproducibility obtained in this study were in the range of 4-16 and 3-25% for spiked standards and SRM 1649, respectively. The optimized and validated MAE technique was applied to the extraction of PAHs from a set of real world PM samples collected in Singapore. The sum of particulate-bound PAHs in outdoor PM ranged from 1.05 to 3.45 ng m⁻³ while that in indoor PM (cooking emissions) ranged from 27.6 to 75.7 ng m⁻³, respectively.     

Ultrasound-assisted extraction and on-line LC–GC–MS for determination of polycyclic aromatic hydrocarbons (PAH) in urban dust and diesel particulate matter

A method has been developed for determination of polycyclic aromatic hydrocarbons (PAH) in particulate matter from ambient air and diesel exhaust emissions. It is reproducible and accurate and, compared with similar methods for analysis of individual PAH components in complex matrices, it is relatively fast and simple. Single PAH components can be determined in samples of particulate matter from ambient air and diesel exhaust emissions with LOD of approximately 1 pg/sample. Further, sample throughput is high, because more than 20 samples can be extracted and prepared for analysis in one working (8-h) day. The particulate matter is subjected to ultrasound-assisted extraction, a technique that is shown to extract PAH from particulate material with efficiencies fully comparable with those of Soxhlet extraction. An aliphatic/PAH-enriched fraction is obtained by solid-phase extraction before isolation, separation, and identification/quantification of PAH by on-line liquid chromatography–gas chromatography–mass spectrometry. The method was validated by analysis of US National Institute of Standards and Technology (NIST) Standard Reference Materials (SRM) 1649a, Urban Dust, and 2975, Diesel Particulate Matter. Results from the method are in good agreement with the NIST-certified PAH concentrations and with NIST reference PAH concentrations.     

Optimisation of supercritical fluid extraction of polycyclic aromatic hydrocarbons and their nitrated derivatives adsorbed on highly sorptive diesel particulate matter

Supercritical fluid extraction (SFE) was performed to extract complex mixtures of polycyclic aromatic hydrocarbons (PAHs), nitrated derivatives (nitroPAHs) and heavy n-alkanes from spiked soot particulates that resulted from the incomplete combustion of diesel oils. This polluted material, resulting from combustion in a light diesel engine and collected at high temperature inside the particulate filter placed just after the engine, was particularly resistant to conventional extraction techniques, such as soxhlet extraction, and had an extraction behaviour that differed markedly from certified reference materials (SRM 1650). A factorial experimental design was performed, simultaneously modelling the influence of four SFE experimental factors on the recovery yields, i.e.: the temperature and the pressure of the supercritical fluid, the nature and the percentage of the organic modifier added to CO₂ (chloroform, tetrahydrofuran, methylene chloride), as a means to reach the optimal extraction yields for all the studied target pollutants. The results of modelling showed that the supercritical fluid pressure had to be kept at its maximum level (30 MPa) and the temperature had to be kept relatively low (75 °C). Under these operating conditions, adding 15% of methylene chloride to the CO₂ permitted quantitative extraction of not only light PAHs and their nitrated derivatives, but also heavy n-alkanes from the spiked soots. However, heavy polyaromatics were not quantitatively extracted from the refractory carbonaceous solid surface. As such, original organic modifiers were tested, including pyridine, which, as a strong electron donor cosolvent (15% into CO₂), was the most successful. The addition of diethylamine to pyridine, which enhanced the electron donor character of the cosolvent, even increased the extraction yields of the heaviest PAHs, leading to a quantitative extraction of all PAHs (more than 79%) from the diesel particulate matter, with detection limits ranging from 0.5 to 7.8 ng for 100 mg of spiked material. Concerning the nitrated PAHs, a small addition of acetic acid into pyridine, as cosolvents, gave the best results, leading to fair extraction yields (approximately 60%), with detection limits ranging from 18 to 420 ng.     

Evaluation of the efficiency of extraction of PAHs from diesel particulate matter with pressurized solvents

Pressurized Fluid Extraction (PFE) was evaluated for the extraction of polycyclic aromatic hydrocarbons (PAHs) and nitro-derivatives from diesel particulate matter. Extraction conditions were set up by performing several tests in which temperature, solvent strength, pressure, and static time were gradually increased. The results obtained on a laboratory test material made of a "lean" (low content of soluble fraction) Diesel particulate matter indicate that very severe conditions were needed in order to obtain better recoveries of the higher molecular weight molecules. Moreover, extraction efficiency seems to be influenced by the amount of soluble matter in the particulate, so that a "lean" particulate appears more difficult to extract. Recoveries of the deuterated standards of certain PAHs (i.e. indeno[1,2,3- cd]pyrene) were incomplete even with the toughest conditions tested. Experiments carried out on a certified material (SRM 1650 from NIST) also indicate that PFE can perform a better extraction of some of the PAHs than the method used for certification, but still incomplete. Comparison of results obtained on the SRM with different extraction techniques suggests that the composition of the extract varies considerably with the extraction technique and conditions. It is relevant to notice that recent Diesel engines produce leaner particulate: for future materials more drastic extraction conditions will be required.     

Rapid determination of PAHs in soil samples by HPLC with fluorimetric detection following sonication extraction

A rapid method for the determination of PAHs in soil samples based on their extraction with methylene chloride by sonication and subsequent separation by HPLC with fluorimetric detection is proposed. A Hypersil Green PAH column was used with a gradient of acetonitrile/water as the mobile phase, together with a program of nine excitation and emission wavelength pairs. Recoveries were in the range 70–98%, except for acenaphthene and naphthalene, at concentration levels 1.08–442 μg/kg with relative standard deviations in the range 2–15% (n = 4). Total PAHs found in soil samples were in the range 15–282 μg/kg. The results were compared with those obtained by applying the 3540 EPA method for two samples. Received: 9 May 2000 / Revised: 17 June 2000 / Accepted: 23 June 2000     

Optimisation of the extraction of polycyclic aromatic hydrocarbons and their nitrated derivatives from diesel particulate matter using microwave-assisted extraction

Pressurised microwave-assisted extraction was used to extract a complex mixture containing polycyclic aromatic hydrocarbons (PAHs), nitrated PAHs and heavy n-alkanes from a particularly refractory carbonaceous material resulting from the combustion in a diesel engine. A second-order central composite design was used to determine the optimal conditions of extraction in terms of time, temperature, volume and nature of extracting solvent from spiked diesel soots. To begin, methylene chloride, tetrahydrofuran and chloroform were tested for extracting the spiked diesel particulates; however, the nature of these solvents was not really an influential factor. Volume was the most influential factor and was kept at a medium level to enhance the extraction of heavy PAHs without introducing an important dilution factor. Temperature and time were not influential as main factors but interacted with the other factors. Finally, high temperature and duration associated with a medium volume of methylene chloride were better for the extractions. After this optimisation, five-ring and six-ring PAHs were nevertheless not satisfactorily desorbed. Other solvents were therefore tested. Only aromatic ones, and particularly heterocyclic aromatic solvents, managed to desorb the heaviest PAHs. Pyridine, with its both aromatic and its basic character, was the most successful solvent. Desorption was even complete with an addition of 17% of diethylamine into pyridine. So, using MAE, we succeeded in extracting quantitatively, from the spiked refractory diesel soot surface, two-ring to six-ring PAHs, heavy n-alkanes and short nitrated PAHs. However, heavy nitrated PAHs were better extracted with a small addition of acetic acid (1%) into pyridine instead of a basic cosolvent.     

An experimental design approach to optimise the determination of polycyclic aromatic hydrocarbons from rainfall water using stir bar sorptive extraction and high performance liquid chromatography-fluorescence detection

Stir bar sorptive extraction (SBSE) followed by HPLC-fluorescence detection (FLD) was optimised for analysing 15 polycyclic aromatic hydrocarbons (PAHs) from water samples, especially rainfall water with low PAH content. The literature data described widely different experimental conditions for the extraction of PAHs by SBSE. A chemometric approach was therefore used to evaluate the statistically influential and/or interacting factors, among those described in the literature, and to find the best extraction and desorption conditions. Among six factors studied in a 2(6-2) fractional factorial design, only sample volume, extraction time and the interaction between both of them had significant effects on the PAH extraction recoveries. Optimal sample volume of 10 mL and extraction time of 140 min were obtained with a response surface design. For the desorption conditions, a Box-Behnken design showed that desorption time, temperature and PAH concentrations had significant effects. The best conditions were two successive desorptions with 100 microL of acetonitrile for 25 min at 50 degrees C. The optimised method was repeatable (RSD< or =5.3% for 50 ng L(-1) spiked water and < or =12.8% for 5 ng L(-1) spiked water), linear (R(2)> or =0.9956), with quantitative absolute recoveries (> or =87.8% for 50 ng L(-1) spiked water), and with the LOD between 0.2 and 1.5 ng L(-1). The optimised method was successfully applied to six-rainfall water samples collected in a suburban area. The total PAHs concentrations studied ranged from 31 to 105.1 ng L(-1). Seasonal variation was observed and on average three PAHs were at the highest concentrations (phenanthrene, fluoranthene and pyrene).     

Development of multiwalled carbon nanotubes based micro-solid-phase extraction for the determination of trace levels of sixteen polycyclic aromatic hydrocarbons in environmental water samples

Micro-solid-phase extraction (μ-SPE) was developed for the determination of trace level of 16 United States Environmental Protection Agency priority polycyclic aromatic hydrocarbons (PAHs) in river water samples with gas chromatography-mass spectrometry (GC-MS). In the μ-SPE device, multiwalled carbon nanotubes was employed as sorbent and was packed inside an porous polypropylene membrane "envelope" whose edges were heat-sealed to secure the contents. The μ-SPE device was placed in a stirred sample solution to extract the analytes. The porous polypropylene membrane envelope in μ-SPE device acts as a filter to exclude potential interferences, such as eliminating or reducing the influence of particles that are bigger than the pore size. After extraction, analyte desorption was carried out with a suitable organic solvent under ultrasonication. Important extraction parameters were optimized in detail, including the selection and amount of sorbent materials, the extraction temperature and extraction time, desorption solvent and desorption time, amount of organic modifier, agitation speed and sample ionic strength. Under the developed extraction conditions, the proposed method provided good linearity in the range of 0.1-50 μg/L, low limits of detection (4.2-46.5 ng/L), and good repeatability of the extractions (relative standard deviations, <12%, n=5). The developed μ-SPE method was successfully applied to the extraction of PAHs in river water samples. The μ-SPE method was demonstrated to be a fast and efficient method for the determination of PAHs from environmental water samples.     

Polyaniline-coated magnetite nanoparticles incorporated in alginate beads for the extraction and enrichment of polycyclic aromatic hydrocarbons in water samples

A magnetic solid-phase extraction sorbent consisting of polyaniline-coated magnetite nanoparticles entrapped in alginate beads (PANI/alginate/Fe₃O₄) was successfully synthesised and applied for the extraction and preconcentration of polycyclic aromatic hydrocarbons (PAHs) in water samples. The magnetite nanoparticles helped to provide an easy and rapid isolation of the sorbent from the sample solution using an external magnet. The alginate beads helped to increase the surface area for polyaniline coating. The polyaniline-coated alginate/magnetite composite helped to increase the extraction efficiency due to the π–π interactions between the polyaniline and the PAHs. Various parameters that affected the extraction efficiencies were optimised including the polymerisation time, the amount of sorbent, sample pH, extraction time, ionic strength, and desorption conditions. Under the optimal conditions, a linear response was achieved in the concentration range of 0.040–50.0 µg L^?1, and the limit of detection was 0.010 µg L^?1. This simple, convenient, cost-effective, and environmentally friendly method was successfully applied for the extraction and enrichment of PAHs in water samples. The recoveries ranged from 86.0% to 97.8% with a relative standard deviation <10 %.     

Trace analysis of polycyclic aromatic hydrocarbons in suspended particulate matter by accelerated solvent extraction followed by gas chromatography–mass spectrometry

An analytical procedure based on extraction by accelerated solvent extraction (ASE) followed by gas chromatography–mass spectrometry (GC/MS) analysis has been developed for the determination of particulate polycyclic aromatic hydrocarbons (PAHs) from large-volume water samples (20 L). The effect of temperature and number of cycles on the efficiency of ASE was investigated: the best results were obtained by using a temperature of 100°C and one static cycle. A mixture of hexane/acetone 1:1 (v/v) was used as extraction solvent. Mean total method recovery under optimized conditions was 85%. The developed methodology was applied to the analysis of suspended particulate matter from Lake Maggiore waters (north of Italy). Mean PAH concentrations in suspended particulate matter from Lake Maggiore ranged from 0.2 ng L⁻¹ for anthracene to 18.7 ng L⁻¹ for naphthalene.     

Determination of polycyclic aromatic hydrocarbons from ambient air particulate matter using a cold fiber solid phase microextraction gas chromatography-mass spectrometry method

Polycyclic aromatic hydrocarbons (PAH) from ambient air particulate matter (PM) were analyzed by a new method that utilized direct immersion (DI) and cold fiber (CF) SPME-GC/MS. Experimental design was used to optimize the conditions of extraction by DI-CF-SPME with a 100μm polydimethylsiloxane (PDMS) fiber. The optimal conditions included a 5min equilibration at 70°C time in an ultrasonic bath with an extraction time of 60min. The optimized method was validated by the analysis of a NIST standard reference material (SRM), 1649b urban dust. The results obtained were in good agreement with certified values. PAH recoveries for reference materials were between 88 and 98%, with a relative standard deviation ranging from 5 to 17%. Detection limits (LOD) varied from 0.02 to 1.16ng and the quantification limits (LOQ) varied from 0.05 to 3.86ng. The optimized and validated method was applied to the determination of PAH from real particulate matter (PM10) and total suspended particulate (TPS) samples collected on quartz fiber filters with high volume samplers.