Small-angle X-ray scattering studies of microdomain structure in segmented polyurethane elastomers

The small-angle x-ray scattering (SAXS) technique has been used to characterize the detailed microphase structure of two crosslinked segmented polyurethane elastomers. Both copolymers contain trifunctional polypropylene ether triols in the rubbery elastomeric block, but are synthesized with different hard segments: a symmetric 4,4′-diphenylmethane diisocyanate (MDI) chain extended with butanediol (BD); and an 80/20 mixture of asymmetric 2,4-toluene diisocyanate (TDI) and symmetric 2,6-toluene diisocyanate (TDI) chain extended with ethylene glycol (EG). Calculations of SAXS invariants and determinations of deviations from Porod's law are used to examine the degree of phase segregation of the hard- and soft-segment domains. Results show that the overall degree of phase separation is poorer in the asymmetric TDI/EG-based copolymer than in the symmetric MDI/BD-based copolymer. Determination of diffuse phase boundary thicknesses, however, reveals that the domain boundaries are sharper in the asymmetric TDI/EG system. The contrasting morphologies found in the two systems are interpreted in terms of differences in hard-soft segment compatibility, diisocyanate symmetry, and diisocyanate length. Coupled with conformational considerations, this information is used to construct a new model for polyurethane hard-segment microdomain structure. Important features of the model are that it takes into account the effects of hard-segment sequence length distribution and allows for folding of the longer hard-segment sequences back into the hard-segment domain.     

聚醚氨酯的微区形态

<正> 聚醚氨酯热塑弹性体是属于(AB)n类型的线型多嵌段共聚物,包括交替的硬段和软段单元.自从1966年Cooper和Tobolsky首先提出聚氨酯具有微相分离的本体结构之假设以后,至今已有大量文献报道了这类材料结构形态与性能关系的研究结果. Wilkes和Koberstein等使用SAXS研究了聚氨酯体系的形态特征.一般认为,聚氨酯材料的微相结构包括一个叠层状或类似叠层状形态,由相分离的软段和硬段组成,平均尺寸为100A的数量级,在软硬段微区之间还存在一相混合的过渡区,其厚度可以从几个埃至几十个埃.然而,SAXS虽然能够高分辨地给出多相体系相分离情况的定     

TEMPERATURE EFFECTED STRUCTURAL TRANSITIONS IN POLYURETHANES SATURATED WITH SOLVENTS STUDIED BY SAXS SYNCHROTRON METHOD

ABSTRACT

A set of segmented polyurethanes (PU) differing in the hard-segment structure was saturated with solvents and after the equilibrium saturation was reached, put to temperature-dependent SAXS investigations. The time-resolved mode of SAXS measurements with a linear increase of temperature from ?70°C to +70°C, i.e., within the temperature range between T_g of soft and hard segments, was applied. The order-order transition leading to a greater degree of order was found at higher temperatures for almost all systems investigated. Some of the PUs exhibit two kinds of microphase separated domains. The results obtained are discussed with respect to the mean-field theory of copolymers and Koberstein and Stein model for hard microdomain structure in PUs, and correlated with temperature dependence of membrane permeability in pervaporation process.     

Structure-property relationships in polycaprolactone-polyurethanes

The structure-property relationships of polycaprolactone-based segmented polyurethanes were studied using differential scanning calorimetry (DSC), small-angle x-ray scattering (SAXS), wide-angle x-ray diffraction (WAXD), dynamic mechanical, and stress-strain testing. The materials studied varied in hard-segment type [4,4′-diphenylmethane diisocyanate/butanediol (MDI/BD) or 4,4′-dicyclohexyl methane diisocyanate/butanediol (H₁₂MDI/BD)], soft-segment molecular weight (830 or 2000 MW polycaprolactone), hard-segment content (23–77% by weight), and thermal history. The materials with aromatic (MDI/BD) hard segments had semicrystalline hard-segment domains, while the materials with aliphatic (H₁₂MDI/BD) hard segment had mostly amorphous domains. Materials with the shorter polycaprolactone soft segment (830 MW) exhibited thermal and mechanical behavior which indicated a considerable degree of hard- and soft-segment compatibility. The materials which contained a 2000-MW polycaprolactone soft segment exhibited better-defined microphase separation. SAXS was used to characterize the microphase structure of each system. The effects of hard-segment content and soft-segment molecular weight were similar for the aromatic (MDI) and aliphatic (H₁₂MDI) hard-segment-based block copolymers. Changing the hard segment from aromatic to aliphatic gave materials with larger interfacial area and slightly higher tensile strength. A range of morphologies between isolated hard domains in a rubbery matrix and isolated rubbery domains in a hard matrix was observed.     

Segmented polyurethanes with 4,4′-bis-(6-hydroxyhexoxy) biphenyl as chain extender. I. Synthesis and characterization of 2,4-tdi-polyurethanes

Polyurethanes composed of 2,4-toluene diisocyanate (TDI), poly (butylene adipate) diols (PBA) of different molecular weights, and 4,4′-bis-(6-hydroxyhexoxy) biphenyl (BHHBP) were prepared by a two-step solution polymerization process. The polyurethanes were char-acterized by elemental analysis, NMR, and SEC. The thermal properties were investigated by DSC, DMA, and optical polarizing microscopy. Dependent on the molecular weight of the PBA, a shift in the glass transition temperature T_g of the polyurethanes has been observed by DSC and DMA. Polyurethanes based on poly (butylene adipate)s of M_n ～ 2000 exhibited a T_g nearly independent on the hard-segment content up to 50% LC hard segments, indicating the existence of mainly phase separated soft and hard segments. By shortening the PBA chain length up to 1,000 and further to 600, the T_g of the polyester soft-segment phase increases with growing hard-segment content, a consequence of enhanced interaction between the hard and soft segments. This tendency is observed to the greatest extent at polyurethanes with the shortest, polyester diol and can be interpreted as a partial miscibility or compatibility of hard and soft segments. Although in polyurethanes with PBA 2000 the mesophase can be proven at a hard-segment content of ～ 40%, its appearance in polyure-thances prepared with PBA 1000 or PBA 600 requires a hard-segment content > 60%. © 1995 John Wiley & Sons, Inc.     

Electron microscopy investigations of the morphology of a polyester-polyurethane

In the current paper the morphology of a slightly crosslinked polyester-polyurethane (hard-segment content ca. 33 wt.-%) is studied by means of transmission electron microscopy (TEM). A new staining technique based on ruthenium tetroxide was applied. This new technique allows the unambiguous visualization of the typical microdomain structure of the polyurethane and also of a wide size spectrum of globular hard-segment-rich domains which result from phase separation in the early stage of preparation. The hard-segment-rich microdomains have a size between 1.5 and 10 nm while the globular domains span a size spectrum from 10 to 2000 nm.     

引入PNA、1, 2-PG对聚氨酯胶粘剂微相形态及性能的影响

引入PNA、1; 2-PG对聚氨酯胶粘剂微相形态及性能的影响;聚氨酯胶粘剂;结晶;微相分离;软段;硬段     

Structural and Mechanical Properties of Polybutadiene-Urethane Elastomer

A series of polyurethanes based on hydroxyl-terminated polybutadiene (HTPBD) and cured with Bis-(-hydroxy ethyl)-terephthalate (BHET) have been synthesized. Mechanical, microscopic and kinetic studies were carried out to elucidate the structure-property relationships from the view point of phase separation. We studied the effects of the polymerization method, varying the hard to soft segment ratio and changing the hard-segment domain structure on the properties of the subject materials. Dynamic mechanical responses showed that the Tg of the soft-segment at ?60°C was independent of the hard-segment content, which indicates that the copolymers were well phase separated. A higher hard-segment content brought about a slight increase in the modulus, a moderate increase in the tensile strength and a decrease in the ultimate elongation. The size of the hard-segment domain, as estimated from electron micrographs, ranged from 60A to 100A. It was observed that a higher content of hard-segments causes an increase in the hard-segment domain size. In addition, a general survey of the reaction rate indicated that BHET is less reactive with diphenyl methyl diisocyanate (MDI) than with HTPBD.     

Model MDI/butanediol polyurethanes: Molecular structure,morphology, physical and mechanical properties

Model butanediol–MDI–polypropylene oxide polymers have been synthesized to explore the structure–property relationships in urethane/polyether polymers. The results of mechanical, thermal, and spectroscopic analyses agree remarkably well. The phase mixing in these polymers decreases with increasing hard-segment length, while the hard-segment stability increases with increasing hard-segment length. This is demonstrated clearly by dynamic mechanical, differential scanning calorimetry, infrared, and NMR studies. The importance of hydrogen bonding to the stability of the hard segment is strongly supported by the variable-temperature infrared experiments. The critical hard-segment size for phase segregation was shown to be two butanediols per hard segment. The temperature limit of the flatness of the storage modulus was tied to the thermal stability of the hard-segment hydrogen bonding which is controlled largely by the length of the hard segment and the extent of the hydrogen bonding.     

Detailed analysis of dynamic mechanical properties of TPU nanocomposite: The role of the interfaces

Organo-modified layered silicates (OMLSs) can largely improve mechanical properties of Thermoplastic polyurethanes (TPUs) as well as affect their microdomain morphology. Nanocomposite TPU containing OMLSs were prepared by melt blending at different concentrations. The addition of OMLS has both induced variation in enthalpy of melting of hard and soft phases, and influenced the glass transition temperature of soft domains, as result of the microdomain phase segregation measured by means of fourier transform infrared spectroscopy (FT-IR). Small angle X-ray scattering (SAXS) analysis has shown that the mean distance between hard domains was mostly unaffected by the filler. However, its distribution broadened with the increasing concentration of the OMLSs, resulting in increased extent of the hard domain interface. The storage modulus of TPU nanocomposites incremented with the silicate content, while the dynamic strain scan tests showed pronounced non linear viscoelastic behavior. The analysis of morphological data obtained by SAXS and FT-IR measurements were correlated to thermal and dynamic mechanical properties of TPU samples suggesting a crucial role of the soft domains interface. The storage modulus and loss tangent of TPU nanocomposites were found to increase with the increasing of the interface area of soft domains with both hard domains and OMLS stacks.     

Soy-oil-based segmented polyurethanes

Segmented polyurethanes were prepared from soy polyol, diphenyl methane diisocyanate (MDI), and ethylene glycol or butane diol as chain extenders. Samples were prepared with true hard-segment concentrations (HSC) of about 0, 10, and 40%. Both the soft MDI–polyol and hard MDI/diol segments are glassy at room temperature. These samples were also crosslinked through the polyfunctional polyol soft segment. Partial crystallinity and phase separation were detected in samples with 40% HSC, on the basis of DSC data. Small-angle X-ray scattering shows the existence of phase separation with domain sizes of about 10 nm in the 40% HSC samples, but not in the others. The distribution of domain sizes is considerably broader for the ethylene-glycol extended system compared with that for the butane-diol case. Although the presence of hard segments lowers the crosslink density, samples with higher HSC had higher glass transition temperatures, higher strengths, higher moduli, lower swelling, lower elongation at break, and lower impact strengths. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3178–3190, 2005     

Hard-segment domain sizes in MDI/diol polyurethane elastomers

Wide-angle x-ray line broadening methods have been used to determine the crystallite size and degree of distortion for the crystalline hard domains in MDI/diol polyurethane elastomers. Crystallite widths have been determined from the integral breadths of the 00l reflections following correction for distortions of the second kind according to the method Hosemann for polymers prepared using ethylene glycol, propandiol, butandiol, and hexandiol as the chain extender. These data relate to the width of the crystallites along the chain axis and thus can be interpreted in terms of the morphology of the hard domains. The crystallite sizes increase and the distortions decrease with increasing elongation and annealing time, and the sizes tend toward asymptotic values which correspond approximately to the average lengths of the hard-segment chains. These results rule out any appreciable folding of the hard-segment chains and point to a model for the hard domains formed by lateral aggregation of extended hard segments.     

A scattering study on intermicellar interactions and structures of polymeric micelles

The micellar structure is usually considered to be composed of a hard sphere (liquid) core and a heavily solvated corona. Therefore, the correction for intermicellar interactions at finite concentrations can be relatively complicated. In this article, small-angle neutron scattering of a copolymer, known as Pluronic L64 (PEO₁₃PPO₃₀PEO₁₃), in o-xylene in the presence of D₂O is used to demonstrate that, based on the hard sphere approximation, intermicellar interactions can be corrected by representing the micellar size as having an equivalent hard sphere radius. The procedure remains valid even if the micellar shape becomes asymmetric, with axial ratios of 3 ? 4. For the present system, the equivalent hard sphere radius corresponds to the micellar core radius plus one-half of the micellar shell thickness. With the equivalent hard sphere approach, the scattering behavior of the micelle could be described by using a core-shell structure. © 1994 John Wiley & Sons, Inc.     

Self-assembly via a complex phase transition in mixtures of polystyrene-block -polybutadiene block copolymer and poly(methyl vinyl ether)

The self-assembly of a binary mixture of polystyreneblock-polybutadiene (SB) and poly(methyl vinyl ether) (PVME) was studied by transmission electron microscopy and time-resolved light scattering. The self-assembly studied involved first microphase separation, in which a microdomain structure composed of polybutadiene block chains (PB) was formed in a matrix composed of polystyrene block chains (PS) and PVME homopolymers, and subsequently macrophase separation of the PVME from the microdomain phase of SB. The microphase separation was induced in a film preparation process using a solution cast method at room temperature. The macrophase separation was induced by rapidly heating the film specimens to above a critical temperature where PVME and PS undergo spinodal decomposition (SD). This complex phase transition, involving microphase separation followed by macrophase separation, was found to generate a superlattice structure (or a modulated structure) with two characteristic spacings: A_macro associated with the SD and A_micro associated with the microphase separation, both being generally time-dependent. The growth of the “macrodomains” was found to be pinned at A_macro ˜ 840 nm due to the elastic effect of the microdomain structure. The microdomain structure with A_micro ˜ 57 nm was found to undergo a morphological transition (a transition between two ordered phases of block copolymers) as a consequence of the local composition change of the two polymers induced by the SD.     

Synthesis and characterization of polydimethylsiloxane polyurea-urethanes and related zwitterionomers

A series of segmented polyurea urethane and polyurea block copolymers based on a hexane diisocyanate (HDI) modified aminopropyl terminated polydimethylsiloxane soft segment was synthesized. The hard segments consisted of 4,4′-methylene diphenylene diisocyanate (MDI) which was chain extended with 1,4-butanediol (BD), N-methyldiethanolamine (MDEA), or ethylene diamine. Zwitterionomers were prepared by quaternizing the tertiary amine of the MDEA extended material with γ-propane sultone. The effect of chemical structure on the extent of phase separation and physical properties was studied using a variety of techniques including thermal analysis, dynamic mechanical spectroscopy, tensile testing, and small-angle x-ray scattering. It was observed that the compatibility between the nonpolar polydimethylsiloxane soft segments and the polar urethane hard segments was improved by inserting HDI linkages into the polydimethylsiloxane soft segments. The aggregation of hard segments was enhanced by increasing hard-segment content or by the introduction of ionic functionality. The tensile strength and modulus of these materials was higher than those of polyurethanes containing soft segments based on polydimethylsiloxane and its derivatives.     

Incremental vapor sorption in a phase-segregated polyurethane elastomer

Incremental vapor sorption and desorption runs have been carried out with o-dichlorobenzene (ODCB) a strongly swelling solvent, in 2, 6, and 10 mil polyether polyurethane films. Two-stage sorption behavior occurs at intermediate and higher concentrations but is generally absent in the desorption runs. Analysis of the two-stage curves, using the Berens-Hopfenberg model of independent Fickian diffusion and first-order relaxation processes, leads to apparent diffusion coefficients which increase with thickness and show a pronounced maximum with concentration, whereas the relaxation rate constant decreases with concentration. Correction for the pressure drift during the runs, due to the low vapor pressure of ODCB, reduces the thickness dependence. The negative concentration dependence of the relaxation rate constant is related to the distribution of microdomain stabilities. Calculated values of the self-diffusion coefficient show that the maximum in the apparent diffusion constant with concentration can be accounted for largely, but not entirely, by the thermodynamic contributions. It is proposed that the additional factor is relaxation-controlled swelling which arises from the strong coupling between the matrix and hard-segment responses.     

Patterning of triblock copolymer film and its application for surface-enhanced Raman scattering

In this paper,microphase behavior of an ABC triblock copolymer,polystyrene-block-poly(2-vinylpyridine)-block-poly(ethylene oxide),namely PS-b-P2VP-b-PEO,was systematically studied during spin-coating and solvent vapor annealing based on various parameters,including the types of the solvent,spin speed and thickness.The morphological features and the microdomain location of the different blocks were characterized by atomic force microscope (AFM) and high resolution transmission electron microscopy (HRTEM).With increasing thickness,the order-order transition from nanopores array to the pattern of nanostripes was observed due to microdomain coarsening.These processes of pattern transformation were based on the selectivity of toluene for different blocks and on the contact time between solvent molecules and the three blocks.This work provides different templates for preparation of gold nanoparticle array on silicon wafer,which can be adopted as an active surface-enhanced Raman scattering (SERS) substrate for poly(3-hexylthiophene) (P3HT).     

Small-angle x-ray and light scattering studies of the morphology of blends of poly(ϵ-caprolactone) with poly(vinyl chloride)

Solvent-cast films of blends of poly(?-caprolactone) (PCL) with poly(vinyl chloride) (PVC) were examined by low-angle x-ray scattering and by small-angle light scattering. X-ray scattering from crystalline compositions were analyzed using the Tsvankin–Buchanan technique and led to values of the repeat period of the lamellar structure and the thickness of the crystalline and amorphous layers. With increasing content of PVC, the amorphous layer thickness increased sufficiently to accommodate the PVC, leading to values of the linear crystallinity consistent with macroscopic measurements by density and DSC techniques up to about 50% PVC by weight. Above this concentration, the lamellar structure no longer appeared to be volume filling. At high concentration of PCL, the polymer consisted of volume-filling spherulites containing the lamellar substructure. Spherulite sizes were measured by light scattering and absolute light scattering intensities were consistent with calculations based upon the degree of crystallinity and anisotropy of the spherulites. Compositions containing more than 60% PVC were amorphous. Low-angle x-ray scattering was interpreted in terms of the Debye–Bueche theory which leads to values for a correlation distance l_c and the mean-square electron density fluctuation 〈η²〉 (which was also obtained from the invariant). By the method of Porod, the correlation distances were resolved into persistence lengths within the two phases, which were determined as a function of composition. The fluctuation 〈η²〉 was analyzed in terms of a two-phase model to show that its value was somewhat larger than would be obtained if the phases were composed of the pure components. It was not possible to uniquely determine their compositions. The data were consistent with the existence of a transition zone of the order of 30 Å thick between phases.     

Multiphase structure of segmented polyurethanes: Its relation with spherulite structure

Small-angle light-scattering (SALS), Polarized light microscopy (PLM), differntial scanning calorimetry (DSC), and small-angle x-ray scattering (SAXS) were used to study morphological changes in segmented polyurethanes with 4,4′-diphenylmethane diisocyanate (MDI) and 1,4-butanediol (BD) as the hard segment. It was found. for the first time, that spherulites could form from the melt by quenching the polyurethanes in the melt state to annealing temperatures between 120°C and T_h, the highest annealing temperature for spherulite formation. T_h ranged from 140°C to ca. 170°C and depended upon the hard-and soft-segment compatibility. Within the range 120°C to T_h, the radius of the spherulite increased with increasing hard-segment content at each fixed annealing temperature. Annealing at 135–140°C gave rise to the largest spherulites. SAXS was used to investigate the phase-separated structures corresponding to the spherulite formation. The interdomain spacing increased with increasing hard-segment content and with increasing annealing temperature.The degree of phase separation first increased with increasing annealing temperature from room temperatures (ca. 25°C), reached a maximum at ca. 107°C, and then decreased with further increase in the annealing temperature. On the basis of these observations, the mechanisms of phase separation, crystallization, and spherulite formation are discussed. © 1993 John Wiley & Sons, Inc.