Multiple melting behavior of poly(butylene succinate). I. Thermal analysis of melt‐crystallized samples

The multiple melting behavior of poly(butylene succinate) (PBSu) was studied with differential scanning calorimetry (DSC). Three different PBSu resins, with molecular weights of 1.1 × 10⁵, 1.8 × 10⁵, and 2.5 × 10⁵, were cooled from the melt (150 °C) at various cooling rates (CRs) ranging from 0.2 to 50 K min^?1. The peak crystallization temperature (T_c) of the DSC curve in the cooling process decreased almost linearly with the logarithm of the CR. DSC melting curves for the melt‐crystallized samples were obtained at 10 K min^?1. Double endothermic peaks, a high‐temperature peak H and a low‐temperature peak L, and an exothermic peak located between them appeared. Peak L decreased with increasing CR, whereas peak H increased. An endothermic shoulder peak appeared at the lower temperature of peak H. The CR dependence of the peak melting temperatures [T_m(L) and T_m(H)], recrystallization temperature (T_re), and heat of fusion (ΔH) was obtained. Their fitting curves were obtained as functions of log(CR). T_m(L), T_re, and ΔH decreased almost linearly with log(CR), whereas T_m(H) was almost constant. Peak H decreased with the molecular weight, whereas peak L increased. It was suggested that the rate of the recrystallization decreased with the molecular weight. T_m(L), T_m(H), T_re, and T_c for the lowest molecular weight sample were lower than those for the others. In contrast, ΔH for the highest molecular weight sample was lower than that for the others. If the molecular weight dependence of the melting temperature for PBSu is similar to that for polyethylene, the results for the molecular weight dependence of PBSu can be explained. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2411–2420, 2002     

A modulated dsc study on the in situ polymerization of cyclic butylene terephthalate oligomers

The polymerization of a cyclic butylene terephthalate (CBT) oligomer was studied as a function of temperature (T=200 and 260°C, respectively) by modulated DSC (MDSC). The first heating was followed by cooling after various holding times (5, 15 and 30 min) prior to the second heating which ended always at T=260°C. This allowed us to study the crystallization and melting behavior of the resulting polybutylene terephthalate (PBT), as well. In contrary to the usual belief, the CBT polymerization is exothermic and the related process is superimposed to that of the CBT melting. The melting behavior of the PBT was affected by the polymerization mode (performed below or above the melting temperature of the PBT product) of the CBT. Annealing above the melting temperature of PBT yielded a product featuring double melting. This was attributed to the presence of crystallites with different degrees of perfection. The crystals perfection which occurred via recrystallization/remelting was manifested by a pronounced exothermic peak in the non-reversing trace.     

Effect of annealing on the structure and properties of poly(vinylidene fluoride) β‐form films

Oriented poly(vinylidene fluoride) (PVDF) films consisting of β crystals were prepared by the solid‐state coextrusion (SC) of a gel film near the melting temperature (T_m) and by conventional cold tensile drawing (TD) of a melt‐quenched film. These films were annealed over the temperature range of 75–190 °C (below and above the static T_m) while the sample length was kept constant or constant loads were applied. After annealing with the sample length kept constant, the dynamic Young's modulus markedly decreased because of the relaxation of oriented amorphous chains, as shown by infrared spectroscopy. In contrast, annealing under a constant load improved the chain orientation in both the crystalline and amorphous regions, resulting in an increase in the modulus from an initial 10.5 to 14.3 GPa for the SC and from an initial 3.3 to 4.8 GPa for the TD. The SC, annealed at 190 °C with a constant load corresponding to an initial tension of 200 MPa, exhibited an extreme crystalline‐chain orientation of 0.998 and a modulus of 14.3 GPa, among the highest values ever reported for PVDF. Although the remanent polarization (P_r) of the TD increased slightly from the initial 62 to 68 mC/m², P_r of the SC stayed constant at 100 mC/m² independently of the annealing conditions. This suggests that the P_r value of 100 mC/m² approached the equilibrium value for this PVDF sample containing 3.5 mol % structural defects. Therefore, although the modulus and P_r of the TD increased slightly with annealing, the maximum values achieved by annealing were markedly lower than those of the SC and annealed SC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1701–1712, 2003     

Lamellar thickening in nascent poly(acrylonitrile) upon annealing

No systematic study has been reported on the lamellar thickening in atactic poly(acrylonitrile) (PAN) upon annealing because PAN, in the form of solution‐cast films or their drawn products, generally shows no small‐angle X‐ray scattering (SAXS) maximum corresponding to the lamellar thickness. In this work, PAN crystals were precipitated during the thermal polymerization of acrylonitrile in solution. The nascent PAN film, obtained by the filtration of the crystal suspension, exhibited a clear SAXS maximum revealing the lamellar structure. The lamellar thickening upon annealing of the nascent PAN films was studied in the temperature range 100–180 °C, where the degradation was minimal, as confirmed by the absence of an IR absorption band at 1605 cm⁻¹ ascribed to the cyclized nitrile groups. Above 190 °C, the degradation of the samples was significant, and the SAXS became too broad to determine the scattering maximum. The long period was significantly affected by the annealing time (t_a) and the temperature (T_a). Depending on t_a, three stages were observed for the lamellar thickening behavior. The lamellar thickness stayed constant in stage I (t_a = 0.5–3 min, depending on T_a), rapidly increased in stage II (t_a = 0.5–8 min), and stayed at a constant value characteristic for each T_a at yet longer t_a's in stage III. The lamellar thickness characteristic for T_a increased rapidly with increasing T_a at 165 °C (or higher), which was 152 °C lower than the estimated melting temperature of PAN (T_m = 317 °C). A possible mechanism for such lamellar thickening in PAN far below the T_m is discussed on the basis of the enhanced chain mobility in the crystalline phase above the crystal/crystal reversible transition at 165–170 °C detected by differential scanning calorimetry and wide‐angle X‐ray diffraction. The structural changes associated with annealing are also discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2571–2579, 2000     

On the origin of the multiple melting behavior in poly(ethylene naphthalene‐2,6‐dicarboxylate): Microstructural study as revealed by differential scanning calorimetry and X‐ray scattering

In this article a study on the melting behavior and microstructure of semicrystalline poly(ethylene naphthalene‐2,6‐dicarboxylate) (PEN) prepared by crystallization from the glass under different annealing conditions is presented. The influence of the annealing temperature (T_a), annealing time (t_a), and the heating rate (R_h) at which T_a is reached on the endothermic behavior of the samples was investigated by means of differential scanning calorimetry (DSC). A dual melting behavior appeared for low R_h values (2 deg · min⁻¹) within the range of 145 °C < T_a < 250 °C and 1 min ≤ t_a. ≤ 16 h. Samples subjected to fast heating rates (R_h = 200 deg · min⁻¹) to reach a T_a ≥ 230 °C showed DSC traces in which a transition is observed from three peaks to a single melting peak when t_a increases in the 30–240 min range. On the basis of the DSC results, PEN samples were prepared displaying single or dual endothermic behavior. The microstructure of these samples was studied by wide (WAXS) and small‐angle X‐Ray scattering (SAXS) techniques. The SAXS data were analyzed using the correlation function and interface distribution function formalisms, respectively. In samples with a single melting behavior, microstructural parameters such as the long spacing, the amorphous and the crystalline phase thicknesses are consistent with a lamellar stacking model in which the thickness distributions of both phases are almost the same. For samples exhibiting two melting endotherms, a dual lamellar model, which is in agreement with the experimental results is proposed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1167–1182, 2000     

Investigations of the equilibrium melting temperature in PBT and PC/PBT blends

The melting behavior of poly(butylene terephthalate) and its blends with bisphenol-A polycarbonate was investigated with differential scanning calorimetry. The aim of this work was to determine the equilibrium melting temperature and its dependence on the blend composition using the Hoffman-Weeks plots. It is shown that the critical analysis of various influences on the melting peak is necessary for the reorganization processes and crystallized content of blends. The experimental conditions and the corrections of measured temperatures were derived and discussed. It was found that the use of the extrapolated onset temperature T_m,o of the melting peak is more efficient than the maximum temperature T_m for the Hoffman-Weeks plots. The equilibrium values of pure PBT are determined to be T^o_m,o = 501 K and T^o_m = 506 K. The equilibrium temperatures of the blends do not show a depression with increasing PC content. Using the Nishi-Wang relation, the results can be qualitatively interpreted with a polymer-polymer interaction coefficient χ ≥ 0 between both components. A weak increase in the equilibrium temperature with increasing PC content was observed. A hypothesis to explain this is based on the possibility of a changed population of the different spherulites with various melting temperatures in dependence on PC content. © 1996 John Wiley & Sons, Inc.     

Multiple melting behavior of poly(butylene succinate). II. Thermal analysis of isothermal crystallization and melting process

The multiple melting behavior of poly(butylene succinate) (PBSu) was studied with differential scanning calorimetry (DSC). Three different PBSu resins, with molecular weights (MWs) of 1.1 × 10⁵, 1.8 × 10⁵, and 2.5 × 10⁵, were isothermally crystallized at various crystallization temperatures (T_c) ranging from 70 to 97.5 °C. The T_c dependence of crystallization half‐time (τ) was obtained. DSC melting curves for the isothermally crystallized samples were obtained at a heating rate of 10 K min⁻¹. Three endothermic peaks, an annealing peak, a low‐temperature peak L, and a high‐temperature peak H, and an exothermic peak located between peaks L and H clearly appeared in the DSC curve. In addition, an endothermic small peak S appeared at a lower temperature of peak H. Peak L increased with increasing T_c, whereas peak H decreased. The T_c dependence of the peak melting temperatures [T_m(L) and T_m(H)], recrystallization temperature (T_re), and heat of fusion (ΔH) was obtained. Their fitting curves were obtained as functions of T_c. T_m(L), T_re, and ΔH increased almost linearly with T_c, whereas T_m(H) was almost constant. The maximum rate of recrystallization occurred immediately after the melting. The mechanism of the multiple melting behavior is explained by the melt‐recrystallization model. The high MW samples showed similar T_c dependence of τ, and τ for the lowest MW sample was longer than that for the others. Peak L increased with MW, whereas peak H decreased. In spite of the difference of MW, T_m(L), T_m(H), and T_re almost coincided with each other at the same T_c. The ΔH values, that is crystallinity, for the highest MW sample were smaller than those for the other samples at the same T_c. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2039–2047, 2005     

DENSITY, EQUILIBRIUM HEAT OF FUSION AND EQUILIBRIUM MELTING TEMPERATURE OF NYLON 1010

The density, equilibrium heat of fusion and equilibrium melting temperature of Nylon 1010 were determined by means of infrared spectrum, differential scanning calorimetry, wide angle X-ray diffraction and density measurement techniques. According to Starkweatber' s method crystalline density ρ_c and amorphous density ρ_a were estimated to be 1.098 and 1.003 g/cm~3 respectively by extrapolating the straight lines of the IR absorbanee against density to zero intensity. Owing to the less intense in absorbance and less sensitive to the change in crystallinity of the amorphors band the thus obtained ρ_c was too low in value. Thereby the value of the ratio ρ_c /ρ_a is far less than generally accepted mean value for most crystalline polymers. Accordingly, traditional X-ray diffraction method was used through determining thc crystalline dimension(a=4.9, b=5.4, c=27.8, α=49°β=77.0°, γ=63.5°), and a rather correct value of ρ_c or the crystal density 1.13 g/cm~3 was obtained. The equilibrium heat of fusion △H_m~0 was estimated to be 244.0 J/g piotting △H_m 's of specimens with different crystallinity against their corre sponding specific volumes _(sp), and extrapolating to completely crystalline condition (_(sp)~c= 1/ρ_c) As to the equilibrium melting temperature T_m~0, because of the easiness of recrystallization of melt crystallized Nylon 1010 specimen, the well-known Hoffman's T_m-T_c method failed in determining this value and an usually rarely used Kamide double extrapolation method was adopted. The so obtained value of T_m~0 487 seems to be fairly reasonable.     

Surface properties of hydrosilylated polyolefins annealed in supercritical carbon dioxide

Two hydrosilylated polyolefin compounds are obtained by reacting polypropylene (PP) and polyethylene (PE) with di‐ and multi‐functional hydride‐terminated poly(dimethylsiloxane) (dH‐PDMS and mH‐PDMS), respectively. The PDMS‐rich surface layers on these two samples show different Si concentrations but similar thicknesses. Samples of these materials are annealed in supercritical carbon dioxide (scCO₂) at various temperatures and pressures for different periods of time. On the PP/dH‐PDMS sample, an increase in the annealing temperature does not affect the Si concentration up to 120°C. However, the Si concentration is sharply reduced at T = 150°C at which point the surface appears to be covered by SiO₂ particles. Annealing the PP/dH‐PDMS sample for short times leads to submicron scale SiO₂ particle formation on the surface. The particles form aggregated clusters that spread all over the surface uniformly when the annealing time is extended. However, Si concentration on the PE/mH‐PDMS sample surface is enhanced as the annealing temperature increases, reaching a maximum at an annealing temperature of 100°C. No particle formation is observed on the PE/mH‐PDMS sample surface. The contact angle of both samples is found to increase with annealing temperature. Increasing the scCO₂ pressure leads to a higher Si concentration on the surfaces of both samples. On the other hand, increasing the CO₂ pressure leads to opposite trends in contact angle with the PP/dH‐PDMS sample exhibiting an increasing contact angle and the PE/mH‐PDMS sample exhibiting a decreasing one. Copyright © 2007 John Wiley & Sons, Ltd.     

Multiphase structure of segmented polyurethanes: Its relation with spherulite structure

Small-angle light-scattering (SALS), Polarized light microscopy (PLM), differntial scanning calorimetry (DSC), and small-angle x-ray scattering (SAXS) were used to study morphological changes in segmented polyurethanes with 4,4′-diphenylmethane diisocyanate (MDI) and 1,4-butanediol (BD) as the hard segment. It was found. for the first time, that spherulites could form from the melt by quenching the polyurethanes in the melt state to annealing temperatures between 120°C and T_h, the highest annealing temperature for spherulite formation. T_h ranged from 140°C to ca. 170°C and depended upon the hard-and soft-segment compatibility. Within the range 120°C to T_h, the radius of the spherulite increased with increasing hard-segment content at each fixed annealing temperature. Annealing at 135–140°C gave rise to the largest spherulites. SAXS was used to investigate the phase-separated structures corresponding to the spherulite formation. The interdomain spacing increased with increasing hard-segment content and with increasing annealing temperature.The degree of phase separation first increased with increasing annealing temperature from room temperatures (ca. 25°C), reached a maximum at ca. 107°C, and then decreased with further increase in the annealing temperature. On the basis of these observations, the mechanisms of phase separation, crystallization, and spherulite formation are discussed. © 1993 John Wiley & Sons, Inc.     

Behavior of pressure dependence of melting temperatures in aromatic polyesters: Influence of polymer structure

The thermal behavior of three aromatic polyesters in a homologous series, poly(ethylene terephthalate) (PET), poly(trimethylene terephthalate) (PTT), and poly(butylene terephthalate) (PBT) was studied under hydrostatic pressure up to 200 MPa by using a high pressure differential thermal analysis apparatus. Confining fluid high pressure dilatometer was used to establish the volume–temperature curves (in both solid and liquid regions) from which volume change on melting of these polyesters at atmospheric pressure was determined. Single endothermic peak was seen for PET and PTT, whereas PBT showed double peaks above 50 MPa. Pressure coefficient of melting temperature at atmospheric pressure (dT_m/dp₍₀₎), was obtained from the quadratic fit. The dT_m/dp₍₀₎ for PTT was newly determined to be 0.445 KMPa^?1, whereas for PET and PBT were 0.503 and 0.455 KMPa^?1, respectively, comparable to reported values. The dT_m/dp₍₀₎ exhibited the odd‐even behavior corresponding to odd and even number of methylene groups in the repeat unit. Enthalpy and entropy of fusion had the most influence on this coefficient. Entropy related to conformational and volume change were evaluated and the former was found to have a significant impact on the value of dT_m/dp₍₀₎. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1799–1808, 2009     

The influence of annealing on thermal transitions in a nematic copolyester

Thermal transitions of a glassy, main chain, liquid crystalline, random copolyester, HIQ‐40, have been characterized. HIQ‐40 is made from 40 mol percent p‐hydroxybenzoic acid (HBA) and 30 mol % each of p‐hydroquinone (HQ) and isophthalic acid (IA). This polymer is soluble in organic solvents, permitting the preparation of thin, solution‐cast films that are in a glassy, metastable, optically isotropic state. On first heating of an isotropic HIQ‐40 film in a calorimeter, one glass transition is observed at low temperature (approximately 42°C), and is ascribed to the glass/rubber transition of the isotropic polymer. A cold crystallization exotherm centered near 150°C is observed. This is associated with the development of low levels of crystalline order. A broad melting endotherm is centered at about 310°C; this endotherm marks the melting of crystallites and the transformation to a nematic fluid. A nematic to isotropic transition was not observed by calorimetry. After quenching from the nematic melt, a T_g is observed in the range of 110–115°C and is associated with the glass/rubber transition of the nematically ordered polymer. Annealing optically isotropic films at temperatures above the isotropic glass transition results in the systematic development of axial order. In these annealed samples, T_g increases rapidly until it is near the annealing temperature, then T_g increases more slowly at longer annealing times. In as‐cast films annealed at 120–135°C, the light intensity transmitted through a sample held between crossed polarizers in an optical microscope (a qualitative measure of birefringence and, in turn, axial order) initially increases rapidly and uniformly throughout the sample and, at longer annealing times, approaches asymptotic values that are higher at higher annealing temperatures. The increase in transmitted intensity is ascribed to the development of axial order. The uniform increase in transmitted intensity suggests that ordering occurs by a rather global process and not via a nucleation and growth mechanism. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 505–522, 1999     

Annealing of polymers in the solid-melt region. I. A new approach to estimate the equilibrium melting temperature of polymer crystals

An annealing scheme for semicrystalline polymers is presented whereby a polymer is annealed in its solid-melt region, leading to crystals approaching the equilibrium crystals in terms of melting temperature. The annealing data is mathematically treated to estimate the equilibrium melting temperature (T⁰_m) of polymer crystals. As is the case with any extrapolation procedure, there are minor shortcomings with our approach, but these are far outweighed by the advantages; the latter are exemplified by a comparison with the widely used Hoffman-Weeks method for estimating (T⁰_m). The validity of our annealing scheme for the estimation of (T⁰_m) is demonstrated by analysis of well-studied polymers such as nylon 6, polyethylene terephthalate (PET), polyethylene (PE), polypivalolactone (PPL), and polytetrafluoroethylene (PTFE); other polymers studied include polyether ether ketone (PEEK) and nylon 4,6.     

Self-nucleation and recrystallization of isotactic polypropylene (α phase) investigated by differential scanning calorimetry

The crystallization behavior after partial or complete melting of the α phase of iPP is examined by combined differential scanning calorimetry (DSC) and optical microscopy: calorimetric results are directly correlated with corresponding morphologies of microtome sections of DSC samples. On partial melting at various temperatures (hereafter referred to as T_s) located in a narrow range (4°C) below and near T_m, the number of nuclei increases (as in classical self-nucleation experiments), by several orders of magnitude; on subsequent cooling, the crystallization peak is shifted by up to 25°C. After partial melting in the lower part of the T_s range and recrystallization, the polymers display a prominent morphology “memory effect” whereby a phantom pattern of the initial spherulite morphology is maintained. After partial melting in the upper part of the T_s range the initial morphology is erased and self-nucleation affects only the total number of nuclei. The present experimental procedures make it possible to define, under “standard” conditions, the crystallization range of the polymer and in particular, the maximum crystallization temperature achievable when “ideally” nucleated. © John Wiley & Sons, Inc.     

Melting behavior of poly(ether ether ketone) in its blends with poly(ether imide)

We detail the melting behavior of poly(ether ether ketone) (PEEK) and investigate its melting behavior in miscible blends with poly(ether imide) (PEI). The determination of the equilibrium melting point (T_m⁰) of PEEK is discussed by considering its inhomogeneous morphology. T_m⁰ is obtained by a long extrapolation of a Hoffman–Weeks plot to 384°C. Hindrance of PEEK crystal reorganization induced by PEI during heating is observed over the blend composition investigated (20–75 wt % PEEK). This behavior is correlated with the incorporation of PEI in the interlamellar zones of PEEK crystals. The interaction parameter χ of PEEK/PEI blends is estimated by the equilibrium melting point depression. This gives the interaction density B = ?1.2 cal/cm³, and x = ?0.40 at 400°C. © 1993 John Wiley & Sons, Inc.     

High-temperature aging of Halar film. II. Analysis of melting behavior

Melting behavior of an experimental Halar film, a predominantly alternating 1:1 copolymer of ethylene (E) and chlorotrifluoroethylene (CTFE), has been studied. Differential scanning calorimetry (DSC) reveals single or double melting peaks, depending upon the thermal history. The lower-temperature melting peak T_m1 is produced only by the thermal treatment and shows a strong dependence on annealing time and temperature. On the basis of the DSC and x-ray data it can be suggested that T_m1 represents the melting of relatively small crystallites formed upon annealing. The higher-temperature melting peak T_m2 is always shown at 238°C. (Note: the specification for commercial Halar product is 240°C. The slightly lower melting temperature reported in this study is probably due to the fact that we are dealing with an experimental melt-processed material.) On the basis of the heating rate study we propose that Halar crystallizes with stable crystals (T_m2 = 238°C) regardless of the crystallization conditions, i.e., quenching, slow cooling, or even annealing. Crystals of Halar have a heat of fusion of approximately 35 cal/g or 146 kJ/kg. Detailed analysis of the melting behavior of Halar is presented.     

X‐ray studies on the double melting behavior of poly(butylene terephthalate)

The double melting behavior of poly(butylene terephthalate) (PBT) was studied with differential scanning calorimetry (DSC) and wide‐angle X‐ray analysis. DSC melting curves of melt‐crystallized PBT samples, which we prepared by cooling from the melt (250 °C) at various cooling rates, showed two endothermic peaks and an exothermic peak located between these melting peaks. The cooling rate effect on these peaks was investigated. The melt‐crystallized PBT sample cooled at 24 K min^?1 was heated at a rate of 1 K min^?1, and its diffraction patterns were obtained successively at a rate of one pattern per minute with an X‐ray measurement system equipped with a position‐sensitive proportional counter. The diffraction pattern did not change in the melting process, except for the change in its peak height. This suggests that the double melting behavior does not originate from a change in the crystal structure. The temperature dependence of the diffraction intensity was obtained from the diffraction patterns. With increasing temperature, the intensity decreased gradually in the low‐temperature region and then increased distinctly before a steep decrease due to the final melting. In other words, the temperature‐dependence curve of the diffraction intensity showed a peak that is interpreted as proof of the recrystallization in the melting process. The peak temperature was 216 °C. The temperature‐dependence curve of the enthalpy change obtained by the integration of the DSC curve almost coincided with that of the diffraction intensity. The double melting behavior in the heating process of PBT is concluded to originate from the increase of crystallinity, that is, recrystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2005–2015, 2001     

Effects of annealing above Tg on the physical aging of quenched PLLA studied by modulated temperature FTIR

The effect of the annealing few degrees above the glass transition temperature (T_da = 62 °C) on the physical aging (T_pa = 51 °C) of amorphous quenched poly(l ‐lactide) is investigated by an implementation of variable temperature Fourier transform infrared (FTIR). By using a temperature program composed of a linear heating ramp superimposed to a temperature modulation (modulated temperature FTIR), the reversing and nonreversing intensity variation of selected bands, related to high‐energy gg and low‐energy gt conformers, is investigated. It is observed that the annealing above T _g changes irreversibly the conformation distribution of the liquid polymer. The glasses obtained from annealed and nonannealed liquids behave differently, evolving in the physical aging toward their own liquid state and retaining the memory of their original condition before the vitrification. The recovery through T _g of the relaxation occurred in the physical aging depends not only from aging conditions but also by the thermal history of the sample above the T_g. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 174–181     

Effect of constrained annealing on the mechanical properties of electrospun poly(ethylene oxide) webs containing multiwalled carbon nanotubes

In this work, flexible nanofibrous membranes (mats) of poly(ethylene oxide) (PEO) with and without multiwall carbon nanotubes (MWNTs) were fabricated by electrospinning. The effects of annealing and MWNT concentration on mat morphology, MWNT dispersion within the nanofibers, and the mechanical properties of electrospun mats were studied. Annealing temperatures ranged from 60 °C to 64 °C [near the melting temperature (64 °C via differential scanning calorimetry)] for 4 minutes. Samples were annealed with and without applied tension (constrained and unconstrained annealing). Annealing at the highest temperature (64 °C), before the loss of fibrous morphology, significantly improved fiber–fiber bonding and therefore the tensile strength of the mats. Compared with unconstrained annealing, constrained annealing introduced fiber alignment (and therefore molecular orientation) along the tensile axis (direction of constraint) during annealing and resulted in a significant increase in modulus for all samples (with and without MWNTs). The use of constrained annealing may be a facile approach to enhance modulus in nanofibrous mats while maintaining high porosity. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 787–796     

Synthesis and characterization of wholly aromatic polyesters derived from 1-phenyl-2,6-naphthalene-dicarboxylic acid and aromatic diols

A series of new wholly aromatic polyesters was synthesized by melt polycondensation of 1-phenyl-2,6-naphthalenedicarboxylic acid (PNDA) and diacetates of various aromatic diols. The aromatic diols studied are hydroquinone (HQ), methylhydroquinone (MHQ), phenylhydroquinone (PHQ), (α-phenylisopropyl)hydroquinone (PIHQ), 2,6-naphthalenediol (2,6-ND), 1,4-naphthalenediol (1,4-ND), and 4,4′-biphenol (BP). These polyesters were characterized for their crystallinity, glass transition temperature (T_g), melting temperature (T_m), liquid crystallinity, and thermal stability. In general, crystallinity of the polyesters are very low and the T_g values of the polyesters range from 150 to 172°C depending on the structure of aromatic diols. All of the polymers formed nematic phases above their T_m or T_g. The polyesters derived from PHQ and PIHQ are soluble in chlorinated hydrocarbon solvents. The initial decomposition temperatures of the polyesters are above 400°C under N₂ atmosphere. © 1996 John Wiley & Sons, Inc.