静电纺丝制备具有浸润性梯度的聚酰亚胺纳米纤维膜

采用高压静电纺丝技术, 在非对称异型电极上制备得到放射状聚酰亚胺(PI)纳米纤维膜. 采用环境扫描电子显微镜(ESEM)观察了PI膜的微观形貌以及纳米纤维的排列状态; 采用接触角测量仪研究了水滴浸润性的变化; 采用高敏感性力学微电力学天平测量了水滴的黏附力, 分析了微观形貌变化与水滴浸润性质和黏附性质的关系. 结果表明, 该PI纳米纤维膜沿着非对称异型电极三角电极至弧型电极方向纤维排列由密到疏, 呈放射状, 具有独特的微结构梯度; 整个纤维膜上的PI纳米纤维直径均一且具有光滑均匀表面, 纤维与纤维之间的距离约为几微米到几十微米. 由于PI纳米纤维膜所具有的独特的微结构梯度, 致使沿着微结构梯度方向水滴的接触角(从超疏水到疏水)和黏附力(从低黏附到高黏附)均表现出梯度变化的特征.     

阵列凹坑结构分布与水滴黏附性质的关系

以新鲜玫瑰花花瓣正面为模板, 采用模板印刷法制备具有微米级阵列凹坑和纳米级沟壑结构的聚二甲基硅氧烷(PDMS)薄膜, 通过对该薄膜逐级拉伸改变其微观结构的分布; 采用场发射扫描电子显微镜(SEM)和原子力显微镜(AFM)观察了不同拉伸程度下薄膜表面微观结构的变化, 采用高敏感性微电力学天平测试了样品表面微观结构变化过程中水滴的黏附力, 分析了其微观结构分布与水滴黏附性质的关系; 采用接触角测量仪表征不同拉伸条件下薄膜的浸润性. 结果表明, 随着PDMS薄膜被逐次拉伸, 单位面积内的凹坑结构数目减少, 且凹坑逐渐分离, 凹坑的深度逐渐降低, 水滴更容易浸入到凹坑结构中, 因此水滴与薄膜的黏附力急剧增大; 随着薄膜进一步拉伸, 纳米级沟壑结构会随着凹坑的拉伸而不断伸展, 纳米级沟壑结构的面积增加, 纳米沟壑结构诱捕的空气量逐渐上升, 导致水滴与薄膜表面的接触面积降低, 使得水滴与薄膜的黏附力下降; 继续拉伸PDMS薄膜, 纳米级沟壑结构进一步伸展, 水滴逐渐浸入纳米级沟壑结构中, 水滴与薄膜的黏附力缓慢增大, 当水滴完全进入到纳米级沟壑中时, 水滴与薄膜的黏附力达到极大值, 此时继续拉伸PDMS薄膜, 纳米级沟壑结构随着拉伸程度的增加继续伸展, 水滴与薄膜的接触面积稍有减少, 黏附力将有所下降, 直至薄膜被完全破坏. 由此可见, 微米级凹坑结构和纳米级褶皱结构的分布是影响PDMS薄膜对水滴黏附性质的主要因素.     

生物光子晶体蝴蝶翅膀表面的凝结液滴憎水性

采用环境扫描电子显微镜(ESEM)观测了蝴蝶翅膀的微观结构, 揭示了蝴蝶翅膀颜色的各向异性特征. 采用高速摄像仪实时动态观察了蝴蝶翅膀的水凝结浸润特性, 分别探究了蝴蝶翅膀在水平、 不同倾斜角度以及在振动条件下的水凝结的憎水性. 基于微观结构, 对蝴蝶翅膀的水凝结憎水特性进行机理阐述. 定量描述了其表面的黏滞特性, 并基于蝴蝶翅膀的微观结构效应阐述了翅膀表面水凝结的憎水性机制.     

霸王鞭和麒麟掌叶片的表面微结构及超疏水性

霸王鞭(Euphorbia antiquorum)和麒麟掌(Euphorbia neriifolia var. cristata)是2种特殊的叶片, 正面不疏水而叶片背面超疏水的沙漠植物. 本文通过接触角测试仪、 电子显微镜和表面张力测试仪分别对叶片的超疏水性、 表面微观形貌和表面黏附力进行了测试和表征. 采用模板法, 以聚乙烯醇为模板、 以聚苯乙烯为基底制备仿叶片背面结构的聚苯乙烯薄膜, 并对薄膜表面的超疏水性、 表面微观形貌和表面黏附力进行了测试和表征, 发现这2种叶片背面的平均间距为1~3 μm的层片状微观结构可以构建出具有超疏水高黏附力特性的表面.     

人造玫瑰花花瓣的微结构分布与水滴黏附性质的关系

本文采用模板印刷法制备得到了“人造玫瑰花花瓣”,即具有玫瑰花花瓣结构的PDMS薄膜,通过对该薄膜逐级拉伸改变微观结构的分布;采用环境扫描电镜（ESEM）观察了不同拉伸程度下薄膜表面微观结构的变化,采用高敏感性微电力学天平测试了样品表面微观结构变化过程中水滴的粘附力,分析了微观结构分布与水滴粘附性质的关系;采用接触角测量仪表征不同拉伸条件下薄膜的浸润性.实验结果表明随着PDMS薄膜被逐次拉伸,单位面积内玫瑰花花瓣乳突的数目减少,纳米褶皱面积不断增加,而纳米级褶皱结构尺寸随着拉伸基本上不发生变化,直到样品破坏;与微观结构变化相对应的,该表面对水滴的粘附力先增大后减小,直到该表面彻底破坏.由此可见,微米结构及纳米结构的分布是影响玫瑰花花瓣对水滴粘附的主要因素.     

玫瑰花花瓣微观结构与水滴黏附性质的关系

利用环境扫描电镜(ESEM)分别观察了新鲜、枯萎的玫瑰花花瓣正、反两面的微观形貌,并通过测量样品的表观接触角表征了其浸润性,采用高敏感性微电力学天平测试了样品表面的粘附力,分析了玫瑰花花瓣微观结构与水滴粘附性质的关系.实验结果表明,微米结构主要影响玫瑰花花瓣的超疏水性,而纳米结构则是导致玫瑰花花瓣具有高粘附力的关键原因.     

花生叶表面的高黏附超疏水特性研究及其仿生制备

花生是一种常见的豆科作物.与低黏附超疏水的荷叶不同,花生叶表面同时具有超疏水和高黏附特性.水滴在花生叶表面的接触角为151±2°,显示出超疏水特性.此外,水滴可以牢固地附着在花生叶表面,将花生叶翻转90°甚至180°,水滴均不会从表面滚落,显示了良好的黏附性(黏附力超过80μN).研究发现,花生叶表面呈现微纳米多级结构,丘陵状微米结构表面具有无规则排列的纳米结构.花生叶表面特殊的微纳米多尺度结构是其表面呈现高黏附超疏水特性的关键因素.结合实验数据,对花生叶表面特殊浸润性机理进行了简要阐述.受此启发,利用聚二甲基硅氧烷复形得到了与花生叶表面微结构类似的高黏附疏水表面.本文以期为仿生制备高黏附超疏水表面提供新思路.     

微液滴在仿蛛丝结构TiO_2纤维表面的定向运动与粘附

制备了具有响应性的仿蛛丝周期纺锤节TiO2纤维。通过改变纤维表面微观结构、紫外光照和超声波等手段,仿蛛丝结构TiO2纤维表面浸润性会发生响应性变化。纤维表面的这种浸润性变化,不仅实现了水滴从纺锤节两端到中心处的定向运动,而且可以使得水滴被纤维纺锤节粘附。当仿蛛丝结构TiO2纤维表面为亲水状态时,无论纺锤节光滑还是粗糙,水都是从纺锤节两端向中心方向运动;当仿蛛丝结构TiO2纤维表面疏水时,水滴会被具有粗糙表面的纺锤节两端粘附。     

超疏水性生物表面的研究进展

介绍了几种天然超疏水生物表面的研究进展,包括蛾翅膀、蝉翼、蝴蝶翅膀、白蚁翅膀、甲虫,蚊子的腿、翅及其复眼,水黾的腿部和荷叶的表面。 对现有的仿生超疏水材料的制备方法及常用作表面修饰的低表面能材料做了简单的归纳与总结。 对超疏水材料研究面临的挑战及以后的发展趋势做了展望。     

1993年全国化学竞赛暨冬令营获奖名单

哈佛大学一位化学教授GeorgeM.Whitesides和另一位物理学家Chaudhury发明了一种新的固体表面,这种表面可以使置于其中的水滴沿着与重力相反的方向向上移动。这种表面是一层抛光的硅胶片,当癸基三氯硅烷蒸汽沿着硅胶片扩散时,硅烷便与表面反应,使得表面成了憎水性的了。随着蒸汽的扩散,蒸气在硅胶片上形成了1cm长的梯度。靠近硅烷的硅胶片一端显得特别憎水,而远离硅烷的另一端却仍然保持亲水性。此时把     

仿生表面液固界面摩擦力的动态调控

仿生超疏水材料在自清洁、防雾抗冰、油水分离、集水等领域有着重要应用;而在不同疏水状态之间的转换将大大促进仿生超疏水材料在智能技术领域的应用.利用软印刷技术将玫瑰花表面微观结构转印到聚氨酯弹性体PU膜表面,利用机械应力实现表面微结构的动态实时调控,实现了表面微观结构在各向同性与各向异性之间的可逆转换;利用毛细管投影传感技...     

Microscale correlation between surface chemistry, texture, and the adhesive strength of Staphylococcus epidermidis

Staphylococcus epidermidis is among the most commonly isolated microbes from medical implant infections, particularly in the colonization of blood-contacting devices. We explored the relationships between surface wettability and root-mean-square roughness (Rq) on microbial adhesive strength to a substrate. Molecular-level interactions between S. epidermidis and a variety of chemically and texturally distinct model substrata were characterized using a cellular probe and atomic force microscopy (AFM). Substrata included gold, aliphatic and aromatic self-assembled monolayers, and polymeric and proteinaceous materials. Substrate hydrophobicity, described in terms of the water contact angle, was an insufficient parameter to explain the adhesive force of the bacterium for any of the surfaces. Correlations between adhesion forces and Rq showed weak relationships for most surfaces. We used an alternate methodology to characterize the texture of the surface that is based on a fractal tiling algorithm applied to images of each surface. The relative area as a function of the scale of observation was calculated. The discrete bonding model (DBM) was applied, which describes the area available for bonding interactions over the full range of observational scales contained in the measured substrate texture. Weak negative correlations were obtained between the adhesion forces and the area available for interaction, suggesting that increased roughness decreases bacterial adhesion when nano- to micrometer scales are considered. We suggest that modification of the DBM is needed in order to include discontinuous bonding. The adhesive strength is still related to the area available for bonding on a particular scale, but on some very fine scales, the bacteria may not be able to conform to the valleys or pits of the substrate. Therefore, the bonding between the bacterium and substrate becomes discontinuous, occurring only on the tops of ridges or asperities.     

Pattern-dependent tunable adhesion of superhydrophobic MnO2 nanostructured film

Tuning the adhesive force on a superhydrophobic MnO(2) nanostructured film was achieved by fabricating different patterns including meshlike, ball cactus-like, and tilted nanorod structures. The marvelous modulation range of the adhesive forces from 130 to nearly 0 μN endows these superhydrophobic surfaces with extraordinarily different dynamic properties of water droplets. This pattern-dependent adhesive property is attributed to the kinetic barrier difference resulting from the different continuity of the three-interface contact line. This finding will provide the general strategies for the adhesion adjustment on superhydrophobic surfaces.     

Influence of attractive force on imaging micro‐droplets of water by atomic force microscope

The shape of micro‐droplets of water on a pure copper surface was investigated using the a.c. non‐contact mode of an atomic force microscope (AFM) by applying different attractive forces between the cantilever tip and the liquid surface. The forces largely influenced the observed radii of micro‐droplets; the influence can be reduced significantly by reducing the force. The same attractive force between the cantilever tip and the micro‐droplets is necessary when comparing the contact angles of micro‐droplets on different surfaces. Furthermore, the values of the contact angles of the micro‐droplets should be the average of those on at least four sides of the droplets. Copyright © 2005 John Wiley & Sons, Ltd.     

Sliding/rolling phobic droplets along a fiber: measurement of interfacial forces

Phobic droplet-fiber systems possess complex geometries, which have made full characterization of such systems difficult. This work has used atomic force microscopy (AFM) to measure droplet-fiber forces for oil droplets on oleophobic fibers over a range of fiber diameters. The work adapted a previous method and a theoretical model developed by the authors for philic droplet-fiber systems. A Bayesian statistical model was also used to account for the influence of surface roughness on the droplet-fiber force. In general, it has been found that the force required to move a liquid droplet along an oleophobic filter fiber will be less than that required to move a droplet along an oleophilic fiber. However, because of the effects of pinning and/or wetting behavior, this difference may be less than would otherwise be expected. Droplets with a greater contact angle (~110°) were observed to roll along the fiber, whereas droplets with a lesser contact angle (<90°) would slide.     

Preparation and Characterization of Hydrophobic Nano Silver Film on Butterfly Wings as Bio-template

Hydrophobic nano silver films were fabricated on butterfly wings as bio-template. The micrometric/nano structures and hydrophobicity of the surfaces were investigated with the help of scanning electron microscope（SEM） and video-based contact angle meter. The hydrophobic mechanism of silver film was analyzed with the aid of Cas- sie＇s formula. On the nano silver films of various thicknesses（5, 10, 20, 40, 60, 80, 100 nm）, all the contact an- gles（CAs） of water were bigger than 120°. When the silver film was 5 nm, the CAs of water on it on the wing surfa- ces of Mimathyma nycteis and Speyeria aglaja were 143.2° and 139.2°, respectively. Coated with the sliver film of the same thickness, butterfly wing surface exhibited the CA remarkably bigger than glass slide surface, exhibiting its high hydrophobicity. With the increase of silver film thickness on butterfly wing surface, the hydrophobicity kept de- creasing. The micrometric/nano hierarchical structures on butterfly wing surface result in the transition of metal silver from hydrophilicity to hydrophobicity.     

缓蚀剂吸附行为的电化学及AFM力曲线研究

结合极化曲线,微分电容曲线测试和AFM力曲线技术研究了直链十二胺对氯化钠溶液中铜镍合金的缓蚀行为以及吸附机理。结果表明:十二胺在合金表面形成单分子层吸附膜而起到缓蚀作用。十二胺浓度越大,吸附膜越致密,缓蚀率越高,力曲线上测得的粘附力值也越大。质子化的十二胺在荷负电的合金表面的吸附使电极零电荷电位正移,电荷屏蔽作用使得AFM力曲线上探针与试样之间的长程静电斥力减小。     

Several surfaces with special wettability: Influence on spreading and motion of W/O emulsion droplets

Physical and chemical modifications were made on the surface of the aluminum sheet to change the surface properties and superhydrophobic–hydrophilic wettability gradient surface was made on the perspex surface by using microstructure-pattering technique and self-assembled-monolayer method. By using high-speed video camera system and optical tensiometer, this paper discusses the influence of special surfaces with different wettability on spreading and motion of water, oil, and W/O emulsion droplets both experimentally and theoretically. In addition, the paper also discusses the influence of the superhydrophobic–hydrophilic wettability gradient on fluidity of W/O emulsion droplets and the coalescence process of droplets. The results showed that the contact angle of W/O emulsion droplets on the modified surfaces was related to the water and oil distribution at the three-phase line. On the wettability gradient surface, the droplet moved spontaneously when the droplet was located at the junction of the gradient. A quasi-steady theoretical model was used to analyze the driving and resistant forces acting on a droplet to improve the understanding of the self-transport behavior of the droplets.     

Preparation of Cu-Coated Stainless Steel Surfaces for Superhydrophobic Investigation

Cu-coated stainless steel surfaces containing micro- and nanoscale binary structures with different surface roughness were successfully fabricated by means of a facile one-step electroless plating technology. The resulting surfaces were modified by the low free energy material HFTHTMS (HFTHTMS = (heptadecafluoro-1,1,2,2-tetrahydrodecyl) trimethoxysilane). The experimental results of wettability exhibit that such unmodified surfaces have a strong adhesive force to water droplets, and their contact angles increase with increasing surface roughness, whereas the modified surfaces by HFTHTMS show the superhydrophobic characteristic with contact angles higher than 150° and sliding angles lower than 5°.