基于声压场描述的扩散声场多自由度互易原理研究

应用于复杂结构中频声振分析的扩散场多自由度互易原理采用位移变量描述系统,实质为弹性波场互易原理,应用于声波场时会造成模型自由度数不必要的增加。建立基于声压描述的扩散声场受挡模型,利用声辐射模态描述扩散声场中结构的表面受挡声压;据此提出基于声压描述的扩散声场多自由度互易原理,发现扩散声场中结构表面受挡声压的互谱矩阵与该结构在自由空间中振动辐射声波的声阻矩阵成正比。该互易原理与传统的单自由度互易原理表达形式相似,但适用于任意自由度结构。该互易原理可用于扩散声场中复杂结构的表面受挡声压的自谱及相关分析,仿真研究表明当边界元网格尺寸小于声波波长的1/6(线性单元)或1/3(二次单元)时,数值解与理论解完全吻合。      

开口/封闭薄壳体声辐射和散射的统一边界积分方程解法

推导了在二维和三维空间下开口和封闭薄壳体在任意阻抗边界条件下声辐射和散射的统一边界积分方程.相对于以前的求解方法,该方程求解声辐射和散射问题具有相同的影响矩阵,能够同时求解薄壳体气动和振动噪声的辐射和散射现象,以及分析壳体声阻抗对声波传播的影响.推导的方程可以应用于叶轮机械、管道等噪声和消声器消声性能的预测等方面.在此方程基础上,可以进一步考虑运动边界和运动介质对声辐射和散射的影响. 关键词： 薄壳体 声阻抗 积分方程 边界元方法     

微穿孔板抑制不稳定燃烧的声学数值仿真

为了研究微穿孔板吸声结构对不稳定燃烧的抑制作用,采用高精度的计算气动声学(Computational Aeroacoustics,CAA)方法开展时域下的数值仿真。首先对带有压力时滞模型的三维声学扰动方程进行求解,给出发动机不稳定燃烧的频率信息。然后通过解析模型分析微穿孔板吸声结构的阻抗特性,并由多自由度宽频阻抗模型模拟微穿孔板对该不稳定频率的抑制作用。仿真捕捉到的不稳定燃烧频率与地面试车测得的频率相一致。表明采用的计算气动声学方法及相应模型可以准确地捕捉不稳定燃烧的频率信息,并分析微穿孔板对不稳定燃烧的抑制作用,对于工程上快速预测不稳定燃烧具有一定意义。      

圆孔非线性声阻抗三维时域仿真与特性分析

为研究有限振幅声波作用下圆孔的非线性声学特性,提出了基于三维时域计算流体动力学(CFD)仿真的圆孔非线性声阻抗提取方法,通过求解层流方程来模拟声信号在圆孔及上下游的传播,以及采用横向周期性边界条件来考虑高穿孔率时圆孔之间相互作用的影响。研究了不同幅值声波作用下孔径、厚度和穿孔率对声阻抗的影响规律,通过对质点振速幅值、频率和板厚等组成的无量纲参量进行非线性回归分析,得到了圆孔非线性声阻抗的拟合公式,并将其转换为可考虑多频声波影响的时域模型。最后结合声阻抗时域模型和有限差分方法计算了直通穿孔管消声器在小振幅和有限振幅声波作用下的传递损失,通过与实验测量结果的比较,验证了拟合公式的准确性和实用性。     

Numerical simulation of nonlinear propagation of sound waves in a finite horn

Nonlinear acoustic propagation generated by a piston in a finite horn is numerically studied.A quasi-one-dimensional nonlinear model with varying cross-section uses high-order low-dispersion numerical schemes to solve the governing equation.Because of the nonlinear wave distortion and reflected sound waves at the mouth,broadband time-domain impedance boundary conditions are employed.The impedance approximation can be optimized to identify the complex-conjugate pole-residue pairs of the impedance functions,which can be calculated by fast and efficient recursive convolution.The numerical results agree very well with experimental data in the situations of weak nonlinear wave propagation in an exponential horn,it is shown that the model can describe the broadband characteristics caused by nonlinear distortion.Moreover,finite-amplitude acoustic propagation in types of horns is simulated,including hyperbolic,conical,exponential and sinusoidal horns.It is found that sound pressure levels at the horn mouth are strongly affected by the horn profiles,the driving velocity and frequency of the piston.The paper also discusses the influence of the horn geometry on nonlinear waveform distortion.     

Surface impedance design with ground corrugation for mitigation of large-calibre gun blast noise

The surface impedance design approach is proposed for mitigating large-calibre gun blast noise. Surrounding the blast noise, we employ a group of concentric trenches with critical depths to dampen the propagation of the acoustic wave. These trenches behave like quarter-wavelength resonators and produce acoustic soft surfaces at their openings. The sound pressure is then mitigated over these soft surfaces by destructive interference and the wave attenuates rapidly along the ground surface. To evaluate the overall acoustic performance of such a design, we develop an efficient numerical solver by treating the geometry as a body of revolution (BOR). The symmetry of the structure in the revolution direction allows the 3D boundary integral equation (BIE) for acoustic wave scattering to be reduced to a 2D integral equation by the use of Fourier series expansions. Numerical experiments show that this model can effectively suppress the acoustic wave propagation horizontally and the reduction can reach about 15 dB for large-calibre gun noise with very low-frequency components.     

A Chebyshev–Lagrangian method for acoustic analysis of a rectangular cavity with arbitrary impedance walls

A general Chebyshev–Lagrangian method is proposed to obtain the analytical solution for a rectangular acoustic cavity with arbitrary impedance boundary conditions. The originality of the present paper is the successful attempt of applying orthogonal polynomials, such as Chebyshev polynomials of the first kind, to the analysis of a rectangular sound field with general wall impedance. The sound pressure is uniformly expressed as triplicate Chebyshev polynomial series which is independent in each direction. The Chebyshev polynomial series solution is obtained using the Rayleigh–Ritz procedure after considering the influence of boundary impedance on the cavity as the work done by the impedance surfaces in the Lagrangian function. The accuracy and reliability of the proposed method are validated against the analytical solutions and some numerical results available in the literature. Excellent orthogonality and complete properties of the Chebyshev polynomials ensure the rapid convergence, numerical stability, high accuracy of the current solution. The simplicity and low computational cost of the present approach make it preferable to obtain the results of complex models even in the relative high frequency range by choosing enough truncated terms in the sound pressure expression. Numerous cases with various uniform or non-uniform impedance boundary conditions are analyzed numerically and some of the results can be used as benchmark. It is shown that the impedance boundary condition can effectively influence or modify the acoustic characteristics and response of a cavity.     

有限长号筒中非线性声传播的数值模拟研究

研究了大振幅活塞声源经有限长号筒向外辐射声波的非线性声学问题。采用具有频散保持特性的高精度计算格式求解了适用于变截面管道的一维非线性声场模型,并考虑到声波的非线性畸变及管口处的声反射,加入了宽频时域声阻抗边界条件。宽频阻抗模型的共轭复数系数采用优化拟合方法近似求解,并采用递推卷积算法快速求解出时域声阻抗。在弱非线性条件下模拟指数形号筒中的声传播取得了与已有实验相一致的结果,表明模型能够描述声波非线性畸变带来的宽频特性。进而采用本模型数值模拟了大振幅活塞声源在双曲形、锥形、指数形和正弦形号筒中的非线性声传播问题,结果表明号筒出口声压级受活塞振动速度、频率以及号筒形状的影响,并分析讨论了波形畸变与号筒几何形状之间的关系。      

Effect of flow on quasi-one-dimensional acoustic wave propagation in a variable area duct of finite length

The general equation for the velocity potential of quasi-one-dimensional acoustic wave motion in a variable area, finite duct with one-dimensional flow is derived by using a perturbation technique. The non-linear second-order partial differential equation is linearized and then solved, by either a power series expansion method or the Runge-Kutta fourth-order method, for harmonic time dependence. The boundary condition taken at the duct mouth is that of matching the impedance of the duct sound field to that of the radiation field at the duct opening. Three axial Mach number variations along the duct axis are considered and the results obtained are compared with those for the case of constant Mach number, to determine the influence of the axial velocity gradient on sound propagation. The effect of flow on the radiation impedance is also considered.     

Wide bandwidth acoustic transmission via coiled-up metamaterial with impedance matching layers

Many acoustic metamaterials suffer from a narrow bandwidth transmission because of the impedance mismatch at the airmetamaterial interface. In this paper, a two-dimensional impedance-matched metamaterial with broadband transmission performance is investigated. The impedance matching layer is introduced for a gradient variation of effective impedance from the inlet of the unit to the outlet. The effective medium theory and corresponding effective model are used to explain the underlying mechanism. The improved energy transmission of our designs is demonstrated by experiment and numerical simulation within a broad frequency bandwidth over 6 kHz. Our impedance-matched design can be used to enhance sound absorption, which is expected to present improved acoustic performance in the applications of acoustic damper and muffler.     

Application of the Wiener–Hopf method for describing the propagation of sound in cylindrical and rectangular channels with an impedance jump in the presence of a flow

Exact solutions to problems of the propagation of acoustic modes in lined channels with an impedance jump in the presence of a uniform flow are constructed. Two problems that can be solved by the Wiener- Hopf method—the propagation of acoustic modes in an infinite cylindrical channel with a transverse impedance jump and the propagation of acoustic modes in a rectangular channel with an impedance jump on one of its walls—are considered. On the channel walls, the Ingard–Myers boundary conditions are imposed and, as an additional boundary condition in the vicinity of the junction of the linings, the condition expressing the finiteness of the acoustic energy. Analytical expressions for the amplitudes of the transmitted and reflected fields are obtained.     

Noise reduction in tunnels by hard rough surfaces

This paper examines the feasibility of using two-dimensional hard rough surfaces to reduce noise levels in traffic tunnels with perfectly reflecting boundaries. First, the Twersky boss model is used to estimate the acoustic impedance of a hard rough surface. Second, an image source model is then used to compute the propagation of sound in a long rectangular enclosure with finite impedance. The total sound fields are calculated by summing the contributions from all image sources coherently. Two model tunnels are built to validate the proposed model experimentally. Finally, a case study for a realistic geometrical configuration is presented to explore the use of hard rough surfaces for reducing traffic noise in a tunnel which is constructed with hard boundaries.     

Sound propagation around rigid barriers laterally confined by tall buildings

This paper focuses on the propagation of sound waves in the presence of acoustic barriers placed close to very tall buildings. The boundary element method (BEM) is used to model the acoustic barrier, while the presence of the tall buildings is taken into account by using the image source method. Different geometries are analyzed, representing the cases of a single building, two buildings forming a corner and three buildings defining a laterally confined space. The acoustic barrier is assumed to be non-absorbing, and all the buildings and the ground are modeled as infinite rigid plane surfaces. Calculations are performed in the frequency domain and time signals are then obtained by means of Inverse Fourier Transforms. The sound pressure loss provided by the acoustic barrier is computed, illustrating the importance of the lateral confinements.     

非对称阻抗插入管消声器的Chebyshev-变分法建模与求解

针对非对称阻抗插入管消声器三维理论建模与求解问题,提出了一种半解析变分建模和求解方法,试验及有限元结果验证了理论模型和求解结果的正确性,开展了模态频率、声压响应及传递损失等声场特性的预测分析。首先构建插入管消声器内部子声场拉格朗日泛函,基于声压与质点振速连续性条件,得到插入管消声器三维理论模型。随后,将子声场声压展开为切比雪夫-傅里叶级数组合形式,按里兹法求得消声器三维声场模态信息。搭建了消声器传递损失试验平台,进行了刚性壁面和阻抗壁面消声器传递损失测试试验,对理论模型和计算结果进行了验证。通过算例分析了壁面阻抗的大小、阻抗面积和分布形式以及插入管偏置对消声器消声性能的影响。结果表明,提出的变分建模求解方法是有效的,对消声器壁面阻抗位置和形式的合理设置可有效降低输出声压。      

The use of a hybrid model to compute the nonlinear acoustic performance of silencers for the finite amplitude acoustic wave

In the present study, a hybrid method is proposed for predicting the acoustic performance of a silencer for a nonlinear wave. This method is developed by combining two models: (i) a frequency-domain model for the computation of sound attenuation due to a silencer in a linear regime and (ii) a wavenumber space model for the prediction of the nonlinear time-evolution of finite amplitudes of the acoustic wave in a uniform duct of the same length as the silencer. The present method is proposed under the observation that the physical process of the nonlinear sound attenuation phenomenon of a silencer may be decoupled into two distinct mechanisms: (a) a linear acoustic energy loss that owes to the mismatch in the acoustic impedance between reactive elements and/or the sound absorption of acoustic liners in a silencer; (b) a nonlinear acoustic energy loss that is due to the energy-cascade phenomenon that arises from the nonlinear interaction between components of different frequencies. To establish the validity of the present model for predicting the acoustic performance of silencers, two model problems are considered. First, the performance of simple expansion mufflers with nonlinear incident waves has been predicted. Second, proposed method is applied for computing nonlinear acoustic wave propagation in the NASA Langley impedance duct configuration with ceramic tubular liner (CT57). Both results obtained from the hybrid models are compared with those from computational aero-acoustic techniques in a time-space domain that utilize a high-order finite-difference method. Through these comparisons, it is shown that there are good agreements between the two predictions. The main advantage of the present method is that it can effectively compute the nonlinear acoustic performance of silencers in nonlinear regimes without time-space domain calculations that generally entail a greater computational burden.     

Time-domain impedance formulation for transmission line matrix modelling of outdoor sound propagation

Outdoor sound propagation modelling has attracted considerable attention in the past and has lead to many analytical and numerical models. More recently, the increase of computational power has led to consider time-domain methods that enable to consider transient phenomena. Among these models, the transmission line matrix (TLM) method has been proposed, but the sound absorption at boundaries appears to be a somewhat underdeveloped aspect of this approach. In this paper, a specific implementation of impedance boundary condition is proposed. The method is based on the approximation of the impedance as a sum of linear systems, which allows the formulation of an equivalent impedance model in the time-domain. The proposed implementation is applied for two common impedance models of porous material. Numerical simulations have been carried out in the case of sound propagation over a flat ground with and without an impedance discontinuity, and for several values of specific airflow resistivity. TLM numerical predictions expressed in terms of excess attenuation relative to free field show a good agreement with analytical solutions.     

Propagation of acoustic waves in a fluid-filled pipe with periodic elastic Helmholtz resonators

Helmholtz resonators are widely used to reduce noise in a fluid-filled pipe system. It is a challenge to obtain lowfrequency and broadband attenuation with a small sized cavity. In this paper, the propagation of acoustic waves in a fluid-filled pipe system with periodic elastic Helmholtz resonators is studied theoretically. The resonance frequency and sound transmission loss of one unit are analyzed to validate the correctness of simplified acoustic impedance. The band structure of infinite periodic cells and sound transmission loss of finite periodic cells are calculated by the transfer matrix method and finite element software. The effects of several parameters on band gap and sound transmission loss are probed.Further, the negative bulk modulus of periodic cells with elastic Helmholtz resonators is analyzed. Numerical results show that the acoustic propagation properties in the periodic pipe, such as low frequency, broadband sound transmission, can be improved.     

Acoustic analysis of a rectangular cavity with general impedance boundary conditions

A Fourier series method is proposed for the acoustic analysis of a rectangular cavity with impedance boundary conditions arbitrarily specified on any of the walls. The sound pressure is expressed as the combination of a three-dimensional Fourier cosine series and six supplementary two-dimensional expansions introduced to ensure (accelerate) the uniform and absolute convergence (rate) of the series representation in the cavity including the boundary surfaces. The expansion coefficients are determined using the Rayleigh-Ritz method. Since the pressure field is constructed adequately smooth throughout the entire solution domain, the Rayleigh-Ritz solution is mathematically equivalent to what is obtained from a strong formulation based on directly solving the governing equations and the boundary conditions. To unify the treatments of arbitrary nonuniform impedance boundary conditions, the impedance distribution function on each specified surface is invariantly expressed as a double Fourier series expansion so that all the relevant integrals can be calculated analytically. The modal parameters for the acoustic cavity can be simultaneously obtained from solving a standard matrix eigenvalue problem instead of iteratively solving a nonlinear transcendental equation as in the existing methods. Several numerical examples are presented to demonstrate the effectiveness and reliability of the current method for various impedance boundary conditions, including nonuniform impedance distributions.     

Vibro-acoustic behaviors of an elastically restrained double-panel structure with an acoustic cavity of arbitrary boundary impedance

An analytical study on the vibro-acoustic behaviors of a double-panel structure with an acoustic cavity is presented. Unlike the existing studies, a structural–acoustic coupling model of an elastically restrained double-panel structure with an acoustic cavity having arbitrary impedance on sidewalls around the cavity is developed in which the two dimensional (2D) and three dimensional (3D) modified Fourier series are used to represent the displacement of the panels and the sound pressure inside the cavity, respectively. The unknown expansions coefficients are treated as the generalized coordinates and the Rayleigh–Ritz method is employed to determine displacement and sound pressure solutions based on the energy expressions for the coupled structural–acoustic system. The effectiveness and accuracy of the present model is validated by numerical example and comparison with finite element method (FEM) and existing analytical method, with good agreement achieved. The influence of key parameters on the vibro-acoustic behaviors and sound transmission of the double-panel structure is investigated, including: cavity thickness, boundary conditions, sidewall impedance, and the acoustic medium in the cavity.