Triglyceride Assay by Amperometric Microbial Biosensor: Sample Hydrolysis and Kinetic Approach

ABSTRACT

A triglyceride assay based on triglyceride hydrolysis and glycerol detection was developed. Non-specific lipase isolated from Candida rugosa and intact Gluconobacter oxydans cells, containing membrane-bound glycerol dehydrogenase, were used to develop a biosensor. Two approaches were investigated: analysis of pre-hydrolysed samples and a kinetic approach. The sensor prepared from G. oxydans cells exhibited sensitive and fast response to glycerol: detection limit 20 μM (S/N=3), linear range up to 2 mM and response time 84 s (90% of steady-state). The triglyceride assay of pre-hydrolysed samples was based on a 20 min hydrolysis and determination of released glycerol by the biosensor. A calibration curve linear up to 12 mM was obtained for triolein samples. The kinetic approach was based on simultaneous glyceride hydrolysis and glycerol detection. Analysis time of 10 min, linear range up to 30 mM, and estimated detection limit of 50 μM were achieved using the kinetic approach. The kinetic triglyceride assay is not influenced by free glycerol present in a sample. Storage stability, expressed as a half life (50% of the initial response), was 7 days when trehalose was used as a stabiliser.     

Electrocatalytic Reduction of H2O2 and Oxygen on the Surface of Thionin Incorporated onto MWCNTs Modified Glassy Carbon Electrode: Application to Glucose Detection

A new H₂O₂ enzymeless sensor has been fabricated by incorporation of thionin onto multiwall carbon nanotubes (MWCNTs) modified glassy carbon electrode. First 50 μL of acetone solution containing dispersed MWCNTs was pipetted onto the surface of GC electrode, then, after solvent evaporations, the MWCNTs modified GC electrode was immersed into an aqueous solution of thionin (electroless deposition) for a short period of time <5–50 s. The adsorbed thin film of thionin was found to facilitate the reduction of hydrogen peroxide in the absence of peroxidase enzyme. Also the modified electrode shows excellent catalytic activity for oxygen reduction at reduced overpotential. The rotating modified electrode shows excellent analytical performance for amperometric determination of hydrogen peroxide, at reduced overpotentials. Typical calibration at ?0.3 V vs. reference electrode, Ag/AgCl/3 M KCl, shows a detection limit of 0.38 μM, a sensitivity of 11.5 nA/μM and a liner range from 20 μM to 3.0 mM of hydrogen peroxide. The glucose biosensor was fabricated by covering a thin film of sol–gel composite containing glucose oxides on the surface of thionin/MWCNTs modified GC electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The detection limit, sensitivity and liner calibration rang were 1 μM, 18.3 μA/mM and 10 μM–6.0 mM, respectively. In addition biosensor can reach 90% of steady currents in about 3.0 s and interference effect of the electroactive existing species (ascorbic acid–uric acid and acetaminophen) is eliminated. The usefulness of biosensor for direct glucose quantification in human blood serum matrix is also discussed. This sensor can be used as an amperometric detector for monitoring oxidase based biosensors.     

Morphology controllable synthesis of monkshoodvine root-bark like carbon and its biosensing application

Unique monkshoodvine root-bark like morphology carbon materials (MLC) have been successfully synthesized under hydrothermal conditions. Utilizing the merits of high surface area and good electron conductivity of the MLC, a layered biosensor designed by assembling the MLC, hemoglobin (Hb) and gold nanoparticles was further developed. Scanning electron microscope and transmission electron microscope showed that the morphology of carbon materials can be successfully controlled simply by moderating the initiator amount of precursor and reaction temperature. The results indicated that the MLC was formed at the reaction condition of 5 mg Ferrocene + 6 mL CCl(4) at 280 °C. Electrochemical methods, such as cyclic voltammetry and electrochemical impedance spectroscopy, were used to characterize the layered biosensor and its application for sensitive detection of hydrogen peroxide (H(2)O(2)). Under optimized experimental condition, the linear range for the determination of H(2)O(2) was 0.06 μM to 1.6 mM with a detection limit of 0.03 μM (S/N = 3). Furthermore, the biosensor also showed a fast response (within 2 s) and high stability.     

On-line microdialysis system with poly(amidoamine)-encapsulated Pt nanoparticles biosensor for glutamate sensing in vivo

In this work, an amine-terminated poly (amidoamine) dendrimer containing Pt nanoparticles (PAMAM/Pt) nanocomposite was synthesized and a novel amperometric H(2)O(2) biosensor based on PAMAM/Pt and MWCNTs was developed. The resulting film of MWCNTs/PAMAM/Pt was characterized by transmission electron microscopy (TEM), linear sweep voltammetry (LSV) and amperometric i-t curve. It demonstrates excellent electrocatalytic responses toward the reduction of H(2)O(2) at -200 mV (vs.SCE) without HRP participation. Immobilized with glutamate oxidase (GlutaOx), an effective glutamate biosensor, was fabricated, and the in vivo detection for glutamate was realized combining with the on-line microdialysis system. The glutamate biosensor showed good linear range from 1.0 μM to 50.0 μM with the detection limit of 0.5 μM (S/N=3). The basal level of glutamate in the striatum of rat was detected continuously with this on-line system and was calculated to be 5.80±0.12 μM (n=3). This method was proved to be sensitive and selective and may be feasible in the further application of physiology and pathology.     

Hydrogen peroxide and glucose biosensor based on silver nanowires synthesized by polyol process

Silver nanowires synthesized through a polyol process using polyvinylpyrrolidone as protection (PVP-AgNWs) were used as a new electrode material for constructing a sensor. Hydrogen peroxide (H(2)O(2)) and glucose were used as analytes to demonstrate the sensor performance of the PVP-AgNWs. It is found that the PVP-AgNWs-modified glassy carbon electrode (PVP-AgNWs/GCE) exhibits remarkable catalytic performance toward H(2)O(2) reduction. This sensor has a fast amperometric response time of less than 2 s and the catalytic current is linear over the concentration of H(2)O(2) ranging from 20 μM to 3.62 mM (R = 0.998) with a detection limit of 2.3 μM estimated on a signal-to-noise ratio of 3. A glucose biosensor was constructed by immobilizing glucose oxidase (GOD) onto the surface of the PVP-AgNWs/GCE. The resultant glucose biosensor can be used for glucose detection in human blood serum with a sensitivity of 15.86 μA mM(-1) cm(-2) and good selectivity and stability.     

Detection of hydrogen peroxide in rainwater based on Mg-Al-carbonate layered double hydroxides-catalyzed luminol chemiluminescence

Using a green catalyst of luminol chemiluminescence (CL), Mg-Al-carbonate layered double hydroxides (denoted as Mg-Al-CO(3) LDHs), a novel, sensitive and rapid CL method was developed for the determination of hydrogen peroxide (H(2)O(2)). The corresponding linear regression equation was established in the range of 0.05-10 μM for H(2)O(2). The detection limit (S/N = 3) is 0.02 μM and the relative standard deviation (RSD) for nine repeated measurements of 1.0 μM H(2)O(2) was 2.9%. This proposed method has been successfully applied to detect H(2)O(2) in rainwater samples with good accuracy and precision. The novel methodology is expected to provide a general protocol for the determination of H(2)O(2) as well as for numerous other oxidase-based reactions giving H(2)O(2) as a product (e.g., glucose).     

An amperometric horseradish peroxidase inhibition biosensor for the determination of phenylhydrazine

An amperometric horseradish peroxidase (HRP) inhibition biosensor has been substantially constructed by the help of N,N-dicyclohexylcarbodiimide (DCC), N-hydroxysuccinimide (NHS). The preparation steps and the biosensor response to phenylhydrazine were monitored by electrochemical impedance spectroscopy (EIS), cyclic voltammetry, and chronoamperometry. The proposed biosensor could be applied to determine phenylhydrazine in a 0.10 M phosphate buffer solution containing 1.2 mM hydroquinone and 0.50 mM H(2)O(2) by phenylhydrazine, inhibiting the catalytic activity of the HRP enzyme in the reduction of H(2)O(2). The system was optimized to realize a reliable determination of phenylhydrazine in the range of 2.5 x 10(-7) to 1.1 x 10(-6) M with a detection limit of 8.2 x 10(-8) M and a correlation coefficient of 0.999. The modified electrode displayed good reproducibility, sensitivity and stability for the determination of phenylhydrazine.     

Superoxide radical biosensor based on a nano-composite containing cytochrome c

A biosensor for the quantification of superoxide radical (O(2)˙(-)) was developed based on a nano-composite containing cytochrome c (Cyt c), carboxylated multi-walled carbon nanotubes and a room temperature ionic liquid (RTIL). The immobilized Cyt c was characterized by field emission scanning electron microscopy, electrochemical impedance spectroscopy and cyclic voltammetry. Using this biosensor a formal potential of -280 mV (vs. Ag/AgCl) and electron transfer rate constant of 1.24 was recorded for the immobilized Cyt c in 0.1 M phosphate buffer solution (pH 7.0). The biosensor showed a relatively high sensitivity (7.455 A M(-1) cm(-2)) and a long term stability (180 days) towards O(2)˙(-) in the concentration range from 0.05 to 8.1 μM with a detection limit of 0.03 μM. The selectivity of the biosensor to O(2)˙(-) was verified when its response was compared with those obtained by four potential interfering substances (ascorbic acid, uric acid, acetaminophen and hydrogen peroxide).     

Sensitive detection of H(2)O(2) and H(2)O(2)-related reactant with Ru(bipy)(2)(7,8-dimethyl-dipyridophenazine)(2+) and oligodeoxyribonucleotide

A sensor for H(2)O(2) and H(2)O(2)-related reactant was constructed with oligonucleotides and Ru(bipy)(2)dppx(2+) (bipy = 2,2'-bipyridine, dppx = 7,8-dimethyl-dipyridophenazine), which was performed by converting the H(2)O(2)-induced DNA cleavage into the change of luminescence. The 'DNA light switch' Ru(bipy)(2)dppx(2+) could emit strong luminescence in the presence of dsDNA. DNA cleavage occurred upon addition of H(2)O(2) due to the Fenton reaction, which resulted in the decrease of the luminescence of Ru(bipy)(2)dppx(2+). Therefore, the luminescence intensity depended on the concentration of H(2)O(2) and H(2)O(2)-related reactants, and the detection limits for H(2)O(2), uric acid and cholesterol were 0.20 μM, 0.46 μM and 1.25 μM, respectively. The recovery varied between 94.0% and 105.0% when the assay was applied to the determination of uric acid and cholesterol in biological samples, which demonstrated the good practicability of the assay.     

Amperometric determination of H2O2 at nano-TiO2/DNA/thionin nanocomposite modified electrode

We report electrochemical preparation and characterization of a new biosensor made of nanostructured titanium dioxide (nano-TiO(2)) particles and deoxyribonucleic acid (DNA). Thionin (TN) redox mediator was electrochemically deposited onto DNA/nano-TiO(2) modified glassy carbon electrode (GCE). The X-ray diffraction analysis, atomic force microscope (AFM) and scanning electron microscope (SEM) were used for surface analysis of TN/DNA/nano-TiO(2) film. In neutral buffer solution, TN/DNA/nano-TiO(2)/GCE biosensor exhibited excellent electrocatalytic activity towards the reduction of hydrogen peroxide (H(2)O(2)) and oxygen (O(2)). The biosensor shows excellent analytical performance for amperometric determination of H(2)O(2), at reduced overpotential (-0.2V). The detection limit and liner calibration range were found to be 0.05mM (S/N=3) and 0.05-22.3mM, respectively. In addition, determination of H(2)O(2) in real samples was carried out using the new biosensor with satisfactory results. The TN/DNA/nano-TiO(2)/GCE showed stable and reproducible analytical performance towards the reduction of H(2)O(2). This biosensor can be used as an amperometric biosensor for the determination of H(2)O(2) in real samples.     

Three-dimensional network polyamidoamine dendrimer-Au nanocomposite for the construction of a mediator-free horseradish peroxidase biosensor

A three-dimensional network PAMAM-Au nanocomposite (3D-PAMAM-Au NC) was prepared by using the first generation polyamidoamine dendrimer (G1 PAMAM) as the dispersant agent. The resultant 3D-PAMAM-Au NC was successfully used as an immobilization matrix for the construction of a reagentless mediator-free horseradish peroxidase (HRP)-based H(2)O(2) biosensor on a multi-walled carbon nanotubes (MWCNTs) modified glassy carbon electrode. With the advantages of the three-dimensional network, the organic-inorganic hybrid materials dramatically facilitate the direct electron transfer of HRP, and good bioelectrocatalytic activity towards H(2)O(2) was demonstrated. Under optimum conditions, the current response of the enzyme modified electrode at -0.30 V was detected. The current response is linearly correlated to H(2)O(2) concentration within the range of 18.00 μM to 20.80 mM with a correlation coefficient of 0.9992 and a sensitivity of 377.78 μA mM(-1) cm(-2). The detection limit was down to 6.72 μM (S/N = 3). Furthermore, the biosensor exhibits some other excellent characteristics, such as high selectivity, short response time, and long-term stability. The 3D-PAMAM-Au NC has proved to be a promising biosensing platform for the construction of mediator-free biosensors, and may find wide potential applications in biosensors, biocatalysis, bioelectronics and biofuel cells.     

A non-enzymatic sensor for hydrogen peroxide based on polyaniline, multiwalled carbon nanotubes and gold nanoparticles modified Au electrode

We describe the construction of a polyaniline (PANI), multiwalled carbon nanotubes (MWCNTs) and gold nanoparticles (AuNPs) modified Au electrode for determination of hydrogen peroxide without using peroxidase (HRP). The AuNPs/MWCNT/PANI composite film deposited on Au electrode was characterized by Scanning Electron Microscopy (SEM) and electrochemical methods. Cyclic voltammetric (CV) studies of the electrode at different stages of construction demonstrated that the modified electrode had enhanced electrochemical oxidation of H(2)O(2), which offers a number of attractive features to develop amperometric sensors based on split of H(2)O(2). The amperometric response to H(2)O(2) showed a linear relationship in the range from 3.0 μM to 600.0 μM with a detection limit of 0.3 μM (S/N = 3) and with high sensitivity of 3.3 mA μM(-1). The sensor gave accurate and satisfactory results, when employed for determination of H(2)O(2) in milk and urine.     

A reliable and durable approach for real-time determination of cellular superoxide anion based on biomimetic superoxide dismutase stabilized by a zeolite

This paper demonstrates a reliable and durable method for in situ real-time determination of O(2)˙(-) based on direct electron transfer of Mn(3)(PO(4))(2), which acts as a superoxide dismutase (SOD). Mn(2+) is ion-exchanged into zeolite-ZSM-5 microstructures, and further coated with poly(diallyldimethylammonium chloride) (PDDA). Direct electron transfer of Mn(2+) is greatly facilitated by zeolite microstructures with the formal potential of 561 ± 6 mV vs. Ag|AgCl, which is just located between thermodynamic potentials of O(2)˙(-)/O(2) and O(2)˙(-)/H(2)O(2). The biomimetic catalytic activity of Mn(3)(PO(4))(2), together with the enhanced electron transfer of Mn(2+) obtained at the zeolite electrode has provided a platform for determination of O(2)˙(-) with high selectivity, wide linear range, low detection limit, and quick response. On the other hand, the present Mn(2+)-ZSM/PDDA electrode shows relatively long-term stability, good reproducibility, and biocompatibility, which opens up a way to adhering cells directly onto the film surface for in situ monitoring of cellular species. As a sequence, the remarkable analytical performance of the present O(2)˙(-) biosensor, combined with the characteristics of the Mn(2+)-ZSM/PDDA electrode surface has established a novel approach for real-time determination of O(2)˙(-) released from living cells.     

Amperometric biosensors based on alumina nanoparticles-chitosan-horseradish peroxidase nanobiocomposites for the determination of phenolic compounds

A horseradish peroxidase (HRP) biosensor based on alumina (Al(2)O(3)) nanoparticles-chitosan (CHIT) nanocomposites was developed for the detection of phenolic compounds. UV-Vis spectra and Fourier transform infrared spectra showed that HRP retained its original structure on the Al(2)O(3)/CHIT film. The surface morphologies of the composite films were characterized by scanning electron microscopy. Cyclic voltammetry and amperometry were used to study the proposed electrochemical biosensor. Optimization of the experimental parameters was performed with regard to pH, applied electrode potential and the concentration of hydrogen peroxide. The linear range, sensitivity and detection limit of the biosensor were investigated for eight phenolic compounds. In particular, the linearity of the biosensor for the detection of hydroquinone was obtained from 5 × 10(-9) M to 7 × 10(-5) M with a detection limit of 1 nM (based on the S/N = 3). The optimized biosensor for hydroquinone determination displayed a high sensitivity of 518.4 nA μM(-1) with a response time of ～5 s.     

Electrochemical biosensors based on redox carbon nanotubes prepared by noncovalent functionalization with 1,10-phenanthroline-5,6-dione

To improve the electrocatalytic activities of carbon nanotubes (CNT) towards the oxidation of nicotinamide adenine dinucleotide (NADH), we derive them with a redox mediator, 1,10-phenanthroline-5,6-dione (PD), by the noncovalent functionalization method. The redox carbon nanotubes (PD/CNT/GC) show excellent electrocatalytic activities towards the oxidation of NADH (catalytic reaction rate constant, k(h) = 7.26 × 10(3) M(-1) s(-1)), so the determination of NADH can be achieved with a high sensitivity of 8.77 μA mM(-1) under the potential of 0.0 V with minimal interference. We also develop an amperometric ethanol biosensor by integration of alcohol dehydrogenase (ADH) within the redox carbon nanotubes (PD/CNT/GC). The ethanol biosensor exhibits a wide linear range up to 7 mM with a lower detection limit of 0.30 mM as well as a high sensitivity of 10.85 nA mM(-1).     

Fabrication of Co3O4 nanoparticles-decorated graphene composite for determination of L-tryptophan

A novel Co(3)O(4) nanoparticles-decorated graphene (GR) composite was synthesized by electro-deposition and characterized by scanning electron micrographs, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy and transmission electron microscopy. Then, amperometric biosensors based on a Co(3)O(4) nanoparticles-decorated GR composite modified glassy carbon electrode (GCE) were developed for the sensitive determination of L-tryptophan (Trp). The direct electrooxidation behaviors of Trp on the Co(3)O(4)/GR/Nafion/GCE were carefully investigated by cyclic voltammetry and square wave voltammetry. The results indicated that Trp showed an increase of the oxidation peak current with a negative shift of the oxidation peak potential compared with that on the bare GCE. Under optimum conditions, the proposed biosensor can be applied to the quantification analysis of Trp with a wide linear range covering 0.05-10 μM (R = 0.996) and a low detection limit of 0.01 μM. The experimental results also showed that the sensor exhibited good reproducibility, long-term stability as well as high selectivity. Moreover, the novel biosensor for the detection of Trp in a real amino acid sample with satisfactory results has been proved.     

Anti-inflammatory and free radial scavenging activities of the constituents isolated from Machilus zuihoensis

A new biflavonol glycoside, quercetin-3-O-β-D-glucopyranoside-(3'→O-3')-quercetin-3-O-β-D-galactopyranoside (9), together with eight known compounds was isolated for the first time from the leaves of Machilus zuihoensis Hayata (Lauraceae). The structure of compound 9 was elucidated by various types of spectroscopic data analysis. Analysis of the biological activity assay found that compound 9 showed significant superoxide anion scavenging activity (IC?? is 30.4 μM) and markedly suppressed LPS-induced high mobility group box 1 (HMGB-1) protein secretion in RAW264.7 cells. In addition, the HMGB-1 protein secretion was also inhibited by quercitrin (3), ethyl caffeate (6), and ethyl 3-O-caffeoylquinate (7) treatment. In the LPS-stimulated inducible nitric oxide synthase (iNOS) activation analysis, two known compounds, quercetin (1) and ethyl caffeate (6), were found to markedly suppress nitric oxide (NO) production (IC?? value, 27.6 and 42.9 μM, respectively) in RAW264.7 cells. Additionally, it was determined that ethyl caffeate (6) down-regulated mRNA expressions of iNOS, IL-1β, and IL-10 in the LPS-treatment of RAW264.7 cells via a suppressed NF-kB pathway. These results suggested for the first time that the new compound 9 and other constituents isolated from M. zuihoensis have potential anti-inflammatory and superoxide anion scavenging effects. These constituents may be useful for treating various inflammatory diseases.     

Graphene Quantum Dots‐based Electrochemical Biosensor for Catecholamine Neurotransmitters Detection

An useful electrochemical sensing approach was developed for epinephrine (EP) detection based on graphene quantum dots (GQDs) and laccase modified glassy carbon electrodes (GC). The miniature GC biosensor was designed and constructed via the immobilization of laccase in an electroactive layer of the electrode coated with carbon nanoparticles. This sensing arrangement utilized the catalytic oxidation of EP to epinephrine quinone. The detection process was based on the oxidation of catecholamine in the presence of the enzyme – laccase. With the optimized conditions, the analytical performance demonstrated a high degree of sensitivity −2.9 μA mM⁻¹ cm⁻², selectivity in a broad linear range (1–120×10⁻⁶ M) with detection limit of 83 nM. Moreover, the method was successfully applied for EP determination in labeled pharmacological samples.     

Electrocatalytic activity of horseradish peroxidase/chitosan/carbon microsphere microbiocomposites to hydrogen peroxide

Colloidal carbon microspheres (CMS) are dispersed in chitosan (CHIT) solution to form an organic-inorganic hybrid with excellent micro-environment for the immobilization of biomolecules. A novel amperometric biosensor for the determination of hydrogen peroxide (H(2)O(2)) has been constructed by entrapping horseradish peroxidase (HRP) in as-synthesized CMS/CHIT hybrid. The modification of glassy carbon electrode is made by a simple solution-evaporation method. The electrochemical properties of the biosensor are characterized in electrochemical methods. The proposed biosensor shows high sensitive determination and fast response to H(2)O(2) at -0.15 V. The constructed HRP/CHIT/CMS/GC electrode also exhibits a fine linear correlation with H(2)O(2) concentration. The calculated value of the apparent Michaelis-Menten constant, 2.33 mM, suggests that the HRP in CMS/CHIT hybrid keeps its native bioactivity and has high affinity for H(2)O(2).     

A Novel Superoxide Anion Biosensor for Monitoring Reactive Species of Oxygen Released by Cancer Cells

In this study, novel sensitive and selective hydrogel microstructures to detect superoxide anions released by cancer cells, based on electrochemical biosensors, are proposed. Ferrocene was coupled with superoxide dismutase within a poly(ethylene glycol) diacrylate hydrogel matrix. The pre‐polymer solution was patterned by photolithography in gold microelectrodes fabricated on top of glass slides. The biosensor was characterized by electrochemical impedance spectroscopy and cyclic voltammetry, and was able to detect superoxide anions in a wide linear range from 5 to 100 μM, with a low detection limit of 0.001 μM and sensitivity of 14.1 nA μM/mm². Moreover, the biosensor was able to directly detect reactive oxygen species released from prostate cells. Furthermore, the reproducibility, stability and selectivity of the biosensor achieved better results when compared with the previous report, so this methodology can be used in physiological and pathological detection of reactive oxygen species, providing a powerful platform for clinical diagnostics in the future.