Effect of temperature and solvents on stereospecific polymerization of vinyl alkyl ethers catalyzed by aluminum sulfate–sulfuric acid complex

The effect of polymerization temperature and solvents was determined on the crystallinity of polymers of vinyl isobutyl ether and of vinyl n-butyl ether prepared with aluminum sulfate–sulfuric acid complex catalyst. Principally, the methyl ethyl ketone (MEK)-insoluble fractions of these polymers were used for characterization. Density, per cent crystallinity by x-ray diffraction, infrared ratio, and dilatometric volume contraction of these polymer fractions were used as criteria of crystallinity. The MEK-insoluble fractions of poly(vinyl n-butyl ethers) prepared in carbon disulfide in the temperature range of ?30 to +25°C did not show any significant difference in the values of the above crystallinity parameters. The polymer obtained at 50°C. was less crystalline than the rest of the polymers. The MEK-insoluble fractions of poly(vinyl isobutyl ethers) prepared at 0–50°C. in carbon disulfide and n-heptane solvents also did not significantly differ in their degree of crystallinity. They were, however, decidedly less crystalline than the MEK-insoluble fractions of the corresponding polymers obtained at ?20°C. These data a indicate that on increasing the temperature of polymerization the crystallinity of the polymers was either unchanged or decreased slightly. The polymerizations of vinyl n-butyl ether and vinyl isobutyl ethers were also carried out in binary mixtures of carbon disulfide with n-heptane, chlorobenzene, and MEK. Generally, increasing the concentration of carbon disulfide increased the inherent viscosities of polymers as well as the weight percentage of their MEK-insoluble fractions. The MEK-insoluble fraction of poly(vinyl isobutyl ether) prepared in carbon disulfide-MEK mixture (volume ratio 2:1) was isotactic and highly crystalline. Likewise, the MEK-insoluble fractions of two polymers of vinyl n-butyl ether prepared in MEK itself were also isotactic and highly crystalline. Compared to poly(tetramethylene oxide), these latter fractions exhibited less dependence of rate of crystallization upon temperature. Consequently, at low degrees of supercooling they crystallize much more rapidly than does poly(tetramethylene oxide).     

Quasiliving Carbocationic Polymerization. VIII. Quasiliving Polymerization of Methyl Vinyl Ether and Its Blocking from Quasiliving Poly(isobutyl Vinyl Ether) Dication

Quasiliving carbocationic polymerization of methyl vinyl ether (MVE) was achieved with the p-dicumyl chloride (p-DCC)/AgSbF₆ initiator system by the slow and continuous monomer-addition (quasiliving) technique. A polar solvent (CH₂Cl₂) and a low reaction temperature (-70°C) were optimum for the quasiliving MVE polymerization. Under these conditions, the number-average molecular weight (M _n) of poly(MVE) increased linearly with the cumulative weight of added monomer (W_MVE), and linear M _n versus W_MVE plots passed through the origin. M _n's were inversely proportional to the initial initiator (p-DCC) concentration. Reactions in a nonpolar solvent (toluene) at -70°C or in a polar solvent (CH₂Cl₂) at ?30°C resulted in deviations from these quasiliving characteristics. Block polymerization of MVE from quasiliving poly(isobutyl vinyl ether) dications by the quasiliving technique (p-DCC/AgSbF₆ initiator, CH₂Cl₂ solvent,(-70°C) led to novel isobutyl vinyl ether (IBVE)-MVE block polymers in high yield (>93 wt%) and at high blocking efficiency. The block polymers, most likely poly(MVE-b-IBVE-b-MVE), having M _n = 10,900–14,000 [M _n(center block) = 6,200–9,0001, were soluble in n-heptane and insoluble in water, and gave hazy homogeneous solutions when dissolved in methanol at room temperature.     

Stereospecific polymerization of isobutyl vinyl ether by AIR3–VCl3·LiCl catalyst. II. Effects of polymerization conditions on polymerization

The effect of polymerization conditions such as aging time of the catalyst, polymerization temperature, polymerization time, monomer concentration, and catalyst concentration on the polymerization of isobutyl vinyl ether was intensively studied by using the VCI₃·LiCl–Al(i-Bu)₃ system at an Al(i-Bu)/VCl₃·LiCl ratio of 6 at which the cationic polymerization by VCl₃·LiCl is sufficiently depressed. About 10 min aging of the catalyst in the presence of monomer yields a fairly stable catalytie system. The optimum polymerization temperature is around 30°C. The conversion increased with increasing monomer concentration, whereas the stereospecificity of polymerization decreased. Unexpectedly, the conversion decreased as total catalyst concentration increased. This phenomenon is explained by considering the deactivation of catalytic sites by the excess of Al(i-Bu)₃. A reasonable mechanism from kinetic considerations is that two molecules of Al(i-Bu)₃ deactivate the catalytic site in an equilibrium reaction. This deactivation is understandable by considering that the coordination of two molecules of Al(i-Bu)₃ will occupy all the coordination positions of vanadium, so that there is no room for coordination of monomer coming to the catalytic site.     

Living cationic polymerization of n‐butyl propenyl ether

Cationic polymerization of n‐butyl propenyl ether (BuPE; CH₃CH CHOBu, cis/trans = 64/36) was examined with the HCl–IBVE (isobutyl vinyl ether) adduct/ZnCl₂ initiating system at −15 ∼ −78 °C in nonpolar (hexane, toluene) and polar (dichloromethane) solvents, specifically focusing on the feasibility of its living polymerization. In contrast to alkyl vinyl ethers, the living nature of the growing species in the BuPE polymerization was sensitive to polymerization temperature and solvent. For example, living cationic polymerization of IBVE can be achieved even at 0 °C with HCl–IBVE/ZnCl₂, whereas for BuPE whose β‐methyl group may cause steric hindrance ideal living polymerization occurred only at −78 °C. Another interesting feature of this polymerization is that the polymerization rate in hexane is as large as in dichloromethane, much larger than in toluene. A new method in determining the ratio of the living growing ends to the deactivated ones was developed with a devised monomer‐addition experiments, in which IBVE that can be polymerized in a living fashion below 0 °C was added to the almost completely polymerized solution of BuPE. The amount of the deactivated chain ends became small in hexane even at −40 °C in contrast to other solvents. Thus hexane turned out an excellent solvent for living cationic polymerization of BuPE. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 229–236, 2000     

Living cationic polymerization of dihydrofuran and its derivatives

Cationic polymerization of 2,3‐dihydrofuran (DHF) and its derivatives was examined using base‐stabilized initiating systems with various Lewis acids. Living cationic polymerization of DHF was achieved using Et_1.5AlCl_1.5 in toluene in the presence of THF at 0 °C, whereas it has been reported that only less controlled reactions occurred at 0 °C. Monomer‐addition experiments of DHF and the block copolymerization with isobutyl vinyl ether demonstrated the livingness of the DHF polymerization: the number–average molecular weight of the polymers shifted higher with low polydispersity as the polymerization proceeded after the monomer addition. Furthermore, this base‐stabilized cationic polymerization system allowed living polymerization of ethyl 1‐propenyl ether and 4,5‐dihydro‐2‐methylfuran at ?30 and ?78 °C, respectively. In the polymerization of 2,3‐benzofuran, the long‐lived growing species were produced at ?78 °C. The obtained polymers have higher glass transition temperatures compared to poly(acyclic alkyl vinyl ether)s. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4495–4504, 2008     

Cationic addition polymerization of 1,4‐dioxene using gacl3 as lewis acid catalyst: Long‐lived species‐mediated polymerization

Effective cationic addition polymerization of 1,4‐dioxene, a six‐membered cyclic olefin with two oxygen atoms adjacent to the double bond, was performed using a simple metal halide catalyst system in dichloromethane. The polymerization was controlled when the reaction was conducted using GaCl₃ in conjunction with an isobutyl vinyl ether–HCl adduct as a cationogen at –78°C to give polymers with predetermined molecular weights and relatively narrow molecular weight distributions. The long‐lived properties of the propagating species were further confirmed by a monomer addition experiment and the analyses of the product polymers by ¹H NMR and MALDI–TOF–MS. Although highly clean propagation proceeded, the apparent rate constant changed during the controlled cationic polymerization of 1,4‐dioxene. The reason for the change was discussed based on polymerization results under various conditions. The obtained poly(1,4‐dioxene) exhibited a very high glass transition temperature (T_g) of 217°C and unique solubility. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Free-ionic polymerization of isobutyl vinyl ether by radiation

Radiation-induced free-ionic polymerization of isobutyl vinyl ether in bulk system has been studied by dilatometry and electrical conductivity measurement. Some refinements in kinetic treatment of estimate the propagation rate constant k_p from the rate of polymerization and steady-state conductivity were attempted. Polymerization of superdried monomer which gave a half-power dose-rate dependence of R_p was carried out at 0, 25, and 50°C. The k_p value obtained at 25°C and an activation energy for propagation were estimated as 1.2 ± 0.4 × 10⁵ I./mole-sec and 9.6 ± 2.8 kcal/mole, respectively. In isobutyl vinyl ether, a propagation reaction in free-ionic mechanism was found to be characterized with a high frequency factor and presumably higher activation energy, compared with ion-pair mechanism. Discussions were also made as to several contrasting behaviors between the polymerization of alkyl vinyl ethers and other vinyl monomers as styrene both in free-ion and ion-pair mechanisms.     

Vinyl addition polymerization of norbornene using cyclopentadienylzirconium trichloride activated by isobutyl‐modified methylaluminoxane

Norbornene polymerization using the commercially available and inexpensive catalyst system, cyclopentadienylzirconium trichloride (CpZrCl₃) and isobutyl‐modified methylaluminoxane (MMAO), were carried out over a wide range of polymerization temperatures and monomer concentrations. For the CpZrCl₃ catalyst system activated by aluminoxane with a 40 mol % methyl group and a 60 mol % isobutyl group (MMAO_40/60), the polymerization temperature and monomer concentration significantly affected the molecular weight (M_n) of the obtained polymer and the catalytic activity. With an increase in the polymerization temperature from 0 to 27 °C, the catalytic activity and M_n increased, but these values dramatically decreased with the increasing polymerization temperature from 27 to 70 °C, meaning that the most suitable temperature was 27 °C. The CpZrCl₃/MMAO_40/60 ([Al]/[Zr] = 1000) catalyst system with the [NB] of 2.76 mol L^?1 at 27 °C showed the highest activity of 145 kg mol_Zr^?1 h^?1 and molecular weight of 211,000 g mol^?1. The polymerization using the CpZrCl₃/MMAO_40/60 catalyst system proceeds through the vinyl addition mechanism to produce atactic polynorbornene, which was soluble in chloroform, toluene, and 1,2‐dichlorobenzene, but insoluble in methanol. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1185–1191, 2008     

NMR studies on the stereospecific polymerization of methyl vinyl ether. Part II. Polymerization by sulfuric acid–aluminum sulfate complex: Enantiomorphic catalyst sites model

Highly crystalline poly(methyl vinyl ether) (PMVE) was produced in toluene in a temperature range of 0 to ?20°C. with the use of sulfuric acid–aluminum sulfate complex (SA catalyst). It was found from the NMR spectra that these polymers contained more than 50% of the triad isotactic fraction and the melting point of the unfractionated polymer was about 130°C. However, PMVE containing a large amount of the isotactic fraction was insoluble in nitromethane, so the triad tacticity of highly crystalline PMVE could not be quantitatively determined. The molecular weight of PMVE increased with increasing conversion and increasing polymerization temperature. This behavior is different from that in metal halide catalysts. Also, the stereoregularity of PMVE decreased with increasing monomer concentration. However, addition of a polar solvent and increasing the polymerization temperature had little effect on the stereoregularity of the polymer. The increase in the isotactic fraction at high catalyst concentration and the difference in the monomer composition in the copolymerization of methyl vinyl ether with 2-chloroethyl vinyl ether by SA catalyst from that obtained by BF₃·O(C₂H₅)₂ suggest that the absorption of MVE on a catalyst surface is an important step in the propagation step by SA catalyst. The fraction of the triad tacticity calculated from the enantiomorphic catalyst sites model⁸ coincided with the experimental results. This fact shows that the steric structure of the adding monomer is determined only by the nature of the catalyst irrespective of the nature of a growing chain end. It is concluded, on considering also the results of the previous paper, that completely different factors can control the steric structure of a polymer even for the same monomer when different catalysts are used.     

Radiation-Induced Degradation of a Series of Poly(vinyl Ethers)

The degradative effects of γ-radiation on diethyl ether solutions of poly(alkyl vinyl ethers) under a variety of conditions were studied by polymer molecular weight measurements. Poly(methyl vinyl ether) (PMVE), poly(ethyl vinyl ether) (PEVE), poly(isopropyl vinyl ether) (PIPVE), and poly(isobutyl vinyl ether) (PIBVE) exhibited similar degradative behavior, with G_(SC) values between 0.3 and 0.9 scissions/100 eV at 0°C. Chemically polymerized and radiation-polymerized PEVE samples gave comparable results. Chain degradation was much more pronounced for samples of poly(tert-butyl vinyl ether) (PTBVE) which yielded a G_(SC) value of 3.6 at 0°C. Degradation experiments conducted on PEVE in air resulted in significantly higher rates of scission: G_(SC) = 5.6 scissions/100 eV at 0°C. Chain scission was not measurably influenced by changing the solvent from diethyl ether to di-isopropyl ether. Increased polymer concentration was found to reduce the rate of polymer degradation.     

Stereospecific polymerization of isobutyl vinyl ether. III. Polymerization with VCl3 • LiCl

The polymerization of isobutyl vinyl ether by vanadium trichloride in n-heptane was studied. VCl₃ ? LiCl was prepared by the reduction of VCl₄ with stoichiometric amounts of BuLi. This type of catalyst induces stereospecific polymerization of isobutyl vinyl ether without the action of trialkyl aluminum to an isotactic polymer when a rise in temperature during the polymerization was depressed by cooling. It is suggested that the cause of the stereospecific polymerization might be due to the catalyst structure in which LiCl coexists with VCl₃, namely, VCl₃ ? LiCl or VCl₂ ? 2LiCl as a solid solution in the crystalline lattice, since VCl₃ prepared by thermal decomposition of VCl₄ and a commercial VCl₃ did not produce the crystalline polymer and soluble catalysts such as VCl₄ in heptane and VCl₃ ? LiCl in ether solution did not yield the stereospecific polymer. It was found that some additives, such as tetrahydrofuran or ethylene glycol diphenyl ether, to the catalyst increased the stereospecific polymerization activity of the catalysts. Influence of the polymerization conditions such as temperature, time, monomer and catalyst concentrations, and the kind of solvent on the formed polymer was also examined.     

Cationic polymerization behavior of isobutyl vinyl ether with arenesulfonates as non‐salt‐type latent thermal initiators

Substituted and unsubstituted benzenesulfonic acid cyclohexyl esters (1–7) were synthesized, and their possibility as latent thermal initiators in the cationic polymerization of isobutyl vinyl ether (IBVE) was examined to develop novel non‐salt type latent cationic initiators. Thermal decomposition of cyclohexyl p‐nitrobenzenesulfonate (2) in C₆D₆ at 80°C proceeded to exclusively afford cyclohexene as well as p‐nitrobenzenesulfonic acid. Cationic polymerization of IBVE with 1 mol % of an arenesulfonate (1–6) in bulk was carried out at 40–100°C for 12 h. No polymerization took place below 50°C, while the consumption of IBVE depending on both the polymerization temperature and the structure of the arenesulfonates was observed above 60°C. The obtained polyIBVEs showed bimodal GPC curves in several cases, revealing the intervention of two independent propagation species in the polymerization. The cationic polymerization of IBVE with cyclohexyl 2,4,6‐triisopropylbenzenesulfonate (7) at 80°C confirmed the acceleration effect of bulkiness on the polymerization rate. It was concluded that the polymerization was largely dependent on both electronic and steric factors of the aryl groups of the initiators which were directly related to the stability of the sulfonate anions. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 293–301, 1999     

Stereoregulation in cationic polymerization by designed Lewis acids. II. Effects of alkyl vinyl ether structure

Stereoregulation in the cationic polymerization of various alkyl vinyl ethers was investigated with bis[(2,6‐diisopropyl)phenoxy]titanium dichloride ( 1 ; catalyst) in conjunction with the HCl adduct of isobutyl vinyl ether as an initiator in n‐hexane at −78 °C. The tacticities depended on the substituents of the monomers. Isobutyl and isopropyl vinyl ethers gave highly isotactic polymers (mm = 83%), whereas tert‐butyl and n‐butyl vinyl ethers resulted in lower isotactic contents (mm ∼ 50%) similar to those for TiCl₄, a conventional Lewis acid, thus indicating that the steric bulkiness of the substituents was not the critical factor in stereoregulation. A statistical analysis revealed that the high isospecificity was achieved not by the chain end but by the catalyst 1 or the counteranion derived therefrom. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1060–1066, 2001     

Photoreactions of N-vinylcarbazole induced by metal salts. II. Further studies on the photocationic polymerization sensitized by sodium chloroaurate(III) in nitrobenzene

Further investigations of the photopolymerization of N-vinylcarbazole(VCZ) sensitized by sodium chloroaurate(III) in nitrobenzene were undertaken under irradiation of near-ultraviolet light at 30°C. Copolymerization with isobutyl vinyl ether and the kinetic behavior of polymerization were studied. These propagation and chain-breaking features were discussed in comparison with those obtained in the thermal polymerization. Electron spin resonance spectroscopy was conducted at 77°K in various systems.     

Some new developments in vinyl ether polymerization

Different combinations of acetals with trimethylsilyl iodide have been explored as new initiating systems for the vinyl ether polymerization. The resulting polymers are characterized by controlled molecular weights and narrow molecular weight distributions, confirming the living polymerization mechanism. Acetals can also be used as transfer agents in the polymerization of vinyl ethers. When using 1,1-diethoxyethane (DEE) as transfer agent and isobutyl vinyl ether (IBVE) as monomer, a transfer constant of 0.2 was obtained (at −40°C in toluene). This method, transposed to functional acetals, provides a new way to prepare polyvinyl ethers with one or two functional end groups. The cationic polymerization of isobutyl vinyl ether initiated with the combination triflic acid/thietane, where thietane acts as electron donating moderator, leads to star-shaped polyvinylether-polythietane block-copolymers (at −40°C in dichloromethane). The block-copolymer structure is obtained because the vinyl ether polymerization is stopped when the α-alkoxy thietanium ion (active species) is attacked by a thietane molecule, which is at the same time an initiation reaction for the thietane polymerization. The star-shaped structure of the block-polymer is the result of the intermolecular termination in the cationic polymerization of thietane. When using a bifunctional initiator system, a polymer network is obtained consisting of linear polyIBVE-segments interconnected by branched polythietane segments. These findings support the sulfonium ion structure of the active species in the cationic polymerization of vinyl ethers initiated by the acid-sulfide system.     

Effect of calcination temperature on the physicochemical and catalytic properties of FeSO<Subscript>4</Subscript>/SiO<Subscript>2</Subscript> in hydrogen sulfide oxidation

The effect of calcination temperature on the state of the active component of iron-containing catalysts prepared by the impregnation of silica gel with a solution of FeSO₄ and on their catalytic properties in selective H₂S oxidation to sulfur was studied. With the use of thermal analysis, XPS, and Mössbauer spectroscopy, it was found that an X-ray amorphous iron-containing compound of complex composition was formed on the catalyst surface after thermal treatment in the temperature range of 400–500°C. This compound contained Fe³⁺ cations in three nonequivalent positions characteristic of various oxy and hydroxy sulfates and oxide and sulfate groups as anions. Calcination at 600°C led to the almost complete removal of sulfate groups; as a result, the formation of an oxide structure came into play, and it was completed by the production of finely dispersed iron oxide in the ?-Fe₂O₃ modification (the average particle size of 3.2 nm) after treatment at 900°C. As the calcination temperature was increased from 500 to 700°C, an increase in the catalyst activity in hydrogen sulfide selective oxidation was observed because of a change in the state of the active component. A comparative study of the samples by temperature-programmed sulfidation made it possible to establish that an increase in the calcination temperature leads to an increase in the stability of the iron-containing catalysts to the action of a reaction atmosphere.     

Stereoregularity of poly(vinyl ether)

α-Methylvinyl isobutyl and methyl ethers were polymerized cationically and the structure of the polymers was studied by NMR. Poly(α-methylvinyl methyl ether) polymerized with iodine or ferric chloride as catalyst was found to be almost atactic, whereas poly(α-methylvinyl isobutyl ether) polymerized in toluene with BF₃OEt₂ or AlEt₂Cl as catalyst was found to be isotactic. In both cases, the addition of polar solvent resulted in the increase of syndiotactic structure as is the case with polymerization of alkyl vinyl ether. tert-Butyl vinyl ether was polymerized, and the polymer was converted into poly(vinyl acetate), the structure of which was studied by NMR. A nearly linear relationship between the optical density ratio D₇₂₂/D₇₃₆ in poly(tert-butyl vinyl ether) and the isotacticity of the converted poly(vinyl acetate) was observed.     

Polymerization of 2,2,2-trifluoroethyl vinyl ether

The polymerization of 2,2,2-trifluoroethyl vinyl ether by six different catalyst systems was examined. Low-temperature studies (?78°C) with boron trifluoride etherate catalyst in hydrocarbon and chlorinated solvents slowly yielded low molecular weight polymers which were amorphous and noncrystallizable upon cold drawing. Under similar conditions, polymerizations with boron trifluoride gas were spontaneous, quantitative, and gave relatively high molecular weight, form-stable, amorphous polymer. Heterogeneous polymerizations with chromium trioxide crystals in toluene at 68°C and bulk reactions with ethylmagnesium bromide–carbon tetrachloride catalyst at 40°C failed to produce polymer. Room temperature runs with triisobutylaluminum–titanium tetrachloride catalyst gave amorphous, tacky material. Aluminum hexahydrosulfate heptahydrate (AHS) initiated polymerizations conducted at 25 and 60°C gave low yields of mixtures of amorphous and crystalline polymers, the ratio depending upon the polymerization solvent employed. The infrared spectra and x-ray diffraction intensity curves of crystalline and amorphous poly(trifluoroethyl vinyl ether) are reported and compared herein for the first time.     

New polymer structures based on vinyl ether polymerization

Sequential living cationic polymerization of octadecyl vinyl ether (ODVE) and methyl vinyl ether (MVE) was used for the preparation of amphiphilic ABA‐type block copolymers. The polymerization of ODVE was initiated with the trimethyl silyl iodide/1,1,3,3‐tetramethoxy propane/ZnI₂ system at 0°C in toluene. The living bifunctional polyODVE thus obtained was used as initiator for the polymerization of MVE. Below the LCST of polyMVE (37°C), the copolymers are amphiphiles. Above the LCST of polyMVE, the polyMVE‐blocks become hydrophobic and the amphiphilic nature of the block copolymer is lost. This was demonstrated by using the block copolymers as emulsifiers for water/decane mixtures. The emulsions were stable for several hours at room temperature, while the emulsion stability decreased to about 30 seconds at 40°C. PolyMVE‐α,ω‐bis‐methacrylates were obtained by end‐capping of living bifunctional polyMVE with 2‐hydroxyethyl methacrylate (HEMA). Copolymerization of these bis‐macromers with HEMA leads to segmented networks. The networks showed a reversible swelling/deswelling behavior in water as a function of temperature. This is caused by a change of the hydrophilicity of the polyMVE segments in the networks. Hexa(chloromethyl)melamine, combined with zinc chloride was found to be an efficient hexafunctional initiator for the living cationic polymerization of vinyl ethers. This simple initiating system opens new ways for the synthesis of endgroup‐functionalized star‐shaped poly(vinyl ethers).     

Living cationic polymerization of α‐methyl vinyl ethers using SnCl4

Cationic polymerization of α‐methyl vinyl ethers was examined using an IBEA‐Et_1.5AlCl_1.5/SnCl₄ initiating system in toluene in the presence of ethyl acetate at 0 ～ ?78 °C. 2‐Ethylhexyl 2‐propenyl ether (EHPE) had a higher reactivity, compared to corresponding vinyl ethers. But the resulting polymers had low molecular weights at 0 or ?50 °C. In contrast, the polymerization of EHPE at ?78 °C almost quantitatively proceeded, and the number‐average molecular weight (M_n) of the obtained polymers increased in direct proportion to the EHPE conversion with quite narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.05). In monomer‐addition experiments, the M_n of the polymers shifted higher with low polydispersity as the polymerization proceeded, indicative of living polymerization. In the polymerization of methyl 2‐propenyl ether (MPE), the living‐like propagation also occurred under the reaction conditions similar to those for EHPE, but the elimination of the pendant methoxy groups was observed. The introduction of a more stable terminal group, quenched with sodium diethyl malonate, suppressed this decomposition, and the living polymerization proceeded. The glass transition temperature of the obtained poly(MPE) was 34 °C, which is much higher than that of the corresponding poly(vinyl ether). This poly(MPE) had solubility characteristics that differed from those of poly(vinyl ethers). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2202–2211, 2008