Temperature-programmed desoprtion of H2 from the surfaces of pd/support and Pd-Ag/support catalysts (support = Al2O3, SiO2)

Thermal desorption of H₂ from the surface of Pd/support and Pd-Ag/support (support = Al₂O₃, SiO₂) catalysts has been investigated. Two wide desorption peaks can be observed for the 5% Pd/support catalyst. The presence of these peaks in the thermogram indicates that several adsorption states exist, which is the result of occurrance of different adsorption centers of specific bond strengths for hydrogen. The addition of silver to the palladium catalysts causes a considerable decrease in the size of the high temperature desorption peak. It is also worth noting that the temperature of the maximum of the desorption rate remains practically constant for all bimetallic catalysts studied. This means that the activation energy of the hydrogen desorption process does not change after the introduction of silver to the palladium catalyst.     

过渡金属改性的Pd/TS-1催化氢、氧直接合成H_2O_2的性能

利用等体积浸渍法制备了M-Pd/TS-1(M=Ce,La,Pt,Fe,Co,Ni,Cr,Mn,Zn,Cd,Cu)系列催化剂,并将制得的催化剂用于常压下氢、氧直接合成过氧化氢的反应。考察了M的类型及负载量对M-Pd/TS-1催化剂催化性能的影响。结果表明,M选Ce时,催化剂的性能最好。Ce的最佳掺入量,n_(Ce)/(n_(Ce)+n_(Pd))=0.5%。对Ce改性与未改性的催化剂进行了TEM及静态化学吸附分析,结果表明,掺入Ce可使Pd在TS-1分子筛表面的粒度及分散度得到改善。考察了n_(O_2)/n_(H_2)比,气体流量,反应时间等反应条件对H_2转化率、H_2O_2选择性及收率的影响。在相对优化的工艺条件下,即n_(O_2)/n_(H_2)=3,气体流量为25 mL·min~(-1),反应时间为3 h时,H_2O_2,的收率可达到25.7%,TOF值为18.7 mol·mol~(-1)·h~(-1),此时溶液中H_2O_2的质量百分数为0.8%。     

Direct synthesis of hydrogen peroxide from H2/O2 using Pd/Al2O3 catalysts

Pd/Al₂O₃ catalysts were prepared by the impregnation method and were used for the direct formation of hydrogen peroxide from H₂ and O₂. The H₂O₂ concentration and selectivity were strongly dependent on the solubility of hydrogen in the reaction medium. The modification of the support by halogenate has a beneficial effect on the selectivity. The state of the active Pd on Pd/Al₂O₃ catalysts was studied using X-ray photoelectron spectroscopy, and Pd(0) was found to be active.     

Effect of H2S-uptake on the conversion of cyclohexene on Ru- and Pd-promoted molybdena-alumina catalysts

The effect of H₂S on the activity and selectivity of catalysts (Ru/Al₂O₃, Pd/Al₂O₃ and Ru and Pd promoted molydena-alumina) was different (on differnt catalysts and different conversions of cyclohexene). Ru-containing catalysts showed higher sulfur sensitivities than the Pd-containing ones. The sequence of catalysts by their H₂S uptake related to mass of catalyst was PdMo/Al₂O₃RuMo/Al₂O₃Mo/Al₂O₃>Pd/Al₂O₃Ru/Al₂O₃.     

不同磷含量对NiMoP/Al2O3加氢处理催化剂的影响

采用NiMoP浸渍液浸渍载体γ Al₂O₃制备了不同磷含量的NiMoP/Al₂O₃加氢处理催化剂。为了研究磷对该系列催化剂活性相结构的影响,用二苯并噻吩（DBT）和喹啉为模型化合物,考察了催化剂的加氢脱硫（HDS）和加氢脱氮（HDN）性能。结果表明,添加适当的磷能够提高催化剂的HDS和HDN活性,但是高含量的磷能显著的降低催化剂的催化性能。通过对催化剂进行XRD和HRTEM表征发现,添加磷能够增加MoS2的堆积层数以及Ⅱ型“Ni-Mo-S”相的相对含量,这是因为在制备过程中添加磷降低了活性组分与载体之间的相互作用。     

Effect of metals on the catalytic activity of sulfated zirconia for light naphtha isomerization

We studied on the function of the metal in the sulfated zirconia(SO₄^2–/ZrO₂) catalyst for the isomerization reaction of light paraffins. The addition of Pt to the SO₄^2–/ZrO₂ carrier could keep the high catalytic activity. The improvement in this isomerization activity is because Pt promotes removal of the coke precursor deposited on the catalyst surface. Though this catalytic function was observed in other transition metals, such as Pd, Ru, Ni, Rh and W, Pt exhibited the highest effect among them. It was further found that the Pd/SO₄^2–/ZrO₂–Al₂O₃ catalyst possessed a catalytic function for desulfurization of sulfur-containing light naphtha in addition to the skeletal isomerization. The sulfur tolerance of catalyst depended on the method of adding Pd, and the catalyst prepared by impregnation of the SO₄^2–/ZrO₂–Al₂O₃ with an aqueous solution of Pd exhibited the highest sulfur tolerance.Further, we investigated the improvement in sulfur tolerance of the Pt/SO₄^2–/ZrO₂–Al₂O₃ catalyst by impregnation of Pd. The results of EPMA analysis indicated that this catalyst was a hybrid-type one (Pt/SO₄^2–/ZrO₂–Pd/Al₂O₃) in which Pt/SO₄^2–/ZrO₂ particles and Pd/Al₂O₃ particles adjoined closely. This hybrid catalyst possessed a very high sulfur tolerance to the raw light naphtha that was obtained from the atmospheric distillation apparatus, although this light naphtha contained much sulfur. We assume that such a high sulfur tolerance in the hybrid catalyst is brought about by the isomerization function of Pt/SO₄^2–/ZrO₂ particles and the hydrodesulfurization function of Pd/Al₂O₃ particles. Besides, since the hybrid catalyst also provides high catalytic activity in the isomerization of HDS light naphtha, we suggest that the Pd/Al₂O₃ particles supply atomic hydrogen to the Pt/SO₄^2–/ZrO₂ particles by homolytic dissociation of gaseous hydrogen and also enhance the sulfur tolerance of Pt/SO₄^2–/ZrO₂ particles. Finally, we also propose the most suitable location of Pd and Pt in the metal-supported SO₄^2–/ZrO₂–Al₂O₃ catalyst.     

柠檬酸添加方式对Mo-Ni-P/Al_2O_3催化剂加氢活性的影响

以Mo、Ni为活性组分,Al_2O_3为载体,采用不同柠檬酸添加方法制备了Mo-Ni-P/Al_2O_3催化剂.通过氢气程序升温还原(H2-TPR)、X射线衍射(XRD),透射扫描电镜(TEM)、XPS等表征方法研究催化剂的物化性质.结果表明:催化剂经柠檬酸的后处理,改善了载体氧化铝表面羟基基团的分布,促使Mo物种以八面体配位多核聚钼酸的形态存在,有效地减弱了载体与活性金属之间的强相互作用,提高了Mo物种的分散度与硫化度,使得催化剂形成更多"Mo-Ni-S"加氢活性相,提高了催化剂的加氢活性.与其他处理方法相比,柠檬酸后处理的催化剂对VGO具有更高的加氢脱硫、脱氮与芳烃饱和性能.     

Fischer-Tropsch synthesis over Ru/Al2O3 catalysts

Fischer-Tropsch syntheses (FTS) were carried out in a slurry phase over Ru/Al₂O₃ catalysts using hexadecane as a solvent. The outcome of the FTS was dependent on the oxide support, calcination temperature, synthesis gas composition and sulfur content. The addition of Mn/Na to Ru/Al₂O₃ was effective in raising the initial activity and C5+ selectivity, but after 20 hours, the performance of the modified catalyst was similar to that of the unmodified catalyst. An additional investigation involving the use of fresh vs used catalysts demonstrated that an agglomeration of the metallic Ru, at least in part, does occur during the reaction.     

PdCl2-CuCl2/Al2O3催化剂低温催化CO氧化的失活机理

采用X射线衍射、N₂吸-脱附、X射线光电子能谱分析、氢气-程序升温还原和原位红外漫反射等方法对新鲜和失活的PdCl₂-CuCl₂/Al₂O₃低温催化CO氧化催化剂进行表征,研究了高相对湿度(100%)下催化剂的失活机理.结果表明,催化剂表面沉积的水使得活性铜物种容易从催化剂表面向载体孔道内部迁移,由于Pd、Cu相互作用弱化从而减弱了Pd与Cu物种间的相互作用,使得催化剂的氧化还原性能受到影响,抑制了Pd⁰再氧化为Pd²⁺的过程,从而因CO氧化反应中催化剂氧化还原循环受阻而导致失活.     

Al含量对Pt-SO2-4 /ZrO2-Al2O3固体超强酸催化

通过向SO^2-₄ /ZrO₂催化剂中同时引入适量的Pt和Al₂O₃, 制备出了具有较高催化性能和稳定性的Pt-SO^2-₄ /ZrO₂-Al₂O₃型固体超强酸催化剂. 以正戊烷异构化反应为探针, 考察了Al含量对催化剂性能的影响; 并采用X射线衍射(XRD)、比表面积测定(BET)、红外(IR)光谱、程序升温还原(TPR)、热重-差热分析(TG-DTA)和氨-程序升温脱附(NH₃-TPD)手段对催化剂进行了表征. 结果表明, Al能够提高ZrO₂的晶化温度, 抑制硫的分解, 增加催化剂的比表面积, 增强硫氧键的结合, 提高催化剂的还原性能, 增加催化剂的酸强度和酸总量. 当Al₂O₃含量(质量分数, w)为5.0%时, Pt-SO^2-₄ /ZrO₂-Al₂O₃固体超强酸催化剂的催化活性最好, 在100 h内异戊烷收率可稳定在52.0%以上, 选择性在98.2%以上.     

Elucidation of hydrodesulfurization mechanism on molybdenum‐based catalysts using 35S radioisotope pulse tracer methods

Elucidation of the hydrodesulfurization (HDS) mechanism on molybdenum‐based catalysts using radioisotope tracer methods and reaction kinetics is reviewed. Firstly, to investigate the sulfidation state in Mo/Al₂O₃ and Co–Mo/Al₂O₃ catalysts, presulfiding of these catalysts has been performed using a ³⁵S pulse tracer method. Secondly, HDS of radioactive ³⁵S‐labeled dibenzothiophene was carried out over a series of sulfided molybdena–alumina catalysts and cobalt‐promoted molybdena–alumina catalysts in a pressurized flow reactor to estimate the behavior of sulfur on the working catalysts. Finally, sulfur exchange of a ³⁵S‐labeled catalyst with hydrogen sulfide was performed to estimate the relationship between the amount of labile sulfur and catalytically active sites.     

Propane oxidation over Pd/LaFe0.8Co0.2O3 catalyst

Pd/LaFe_0.8Co_0.2O₃ was found to be more active than the Pd/Al₂O₃ catalyst in propane oxidation. Activity and the oxidation state of palladium were strongly affected by the redox ratio (S) of reactants. Higher propane conversion could be obtained under rich conditions at higher temperatures, contributing to steam reforming. The presence of excess steam would bring about inhibition and oscillation.     

Selective catalytic reduction of NO over metal oxide or noble metal-doped In2O3/Al2O3 catalysts by propene in the presence of oxygen

The activities of metal oxide CuO, SnO₂, CoO, Ag₂O, ZnO or noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts for selective catalytic reduction of NO by propene were investigated. The temperature windows for NO reduction over noble metal-doped In₂O₃/Al₂O₃ catalysts were shifted and broaden slightly compared with single component catalyst alone. This revised version was published online in June 2006 with corrections to the Cover Date.     

Methane Combustion over Pd/Al2O3 Catalyst: Effects of Chlorine Ions and Water on Catalytic Activity

The influences of residual chlorine ions and water on the performance of a Pd/Al₂O₃ catalyst in methane combustion have been studied. The results show that the catalyst containing Cl⁻ exhibits a relatively low activity, and the addition of water to the reaction system accelerates the deactivation process. The catalyst has been characterized by N₂ adsorption, X-ray fluorescence, Fourier transform infrared spectroscopy (FT-IR), and thermogravimetry (TG). The results show that the presence of Cl⁻ appears to strongly inhibit the total oxidation of methane and hinder the dispersion of Pd on Al₂O₃. The formation of Pd(OH)₂ during the reaction is the most likely reason for the inhibition effect of water, which is confirmed by FT-IR and TG analysis. The regeneration of the Pd/Al₂O₃ catalyst can be achieved by purging in nitrogen at 550 °C.     

A novel PdNi/Al2O3 catalyst prepared by galvanic deposition for low temperature methane combustion

Galvanic deposition method was used to prepare the Pd/Ni-Al₂O₃-GD catalyst for the combustion of methane under lean conditions. The new catalyst and compared catalysts (Pd/Al₂O₃-IW, Pd-Ni/Al₂O₃-IW, Pd/Ni-Al₂O₃-IW) prepared by incipient wetness impregnation were characterized by N₂-physisorption, XRD and TEM to clarify particle size and size distribution of palladium species. Combined O₂-TPD and XPS results with the catalytic data, it shows that the surface palladium species with low valence exhibits better combustion performance due to their stronger interaction with support. The results indicate that the galvanic deposition method is an effective route to prepare efficient catalyst for methane combustion, and it also provides useful information for improving the present commercial catalyst.     

Selective hydrogenation of phenylacetylene on Pd/Al2O3: Effect of the addition of Pt and particle size

Phenylacetylene hydrogenation on Pd, Pt and Pd–Pt/Al₂O₃ catalysts has been studied. In all catalysts activity was found not to depend on particle size. However, selectivity to styrene was found to depend on Pd/Al₂O₃ catalysts. Carbon deposition in both metal and support explains such a behavior. Nevertheless, in small Pd particles a longer residence time of styrene may control the selectivity.     

浸渍法制备的Pd-MnO_x/γ-Al_2O_3催化剂及不同载体对地表O_3降解的影响(英文)

在γ-Al2O3载体上用等体积浸渍法浸渍Pd、MnOx活性组分,然后涂覆于堇青石基体上制备Pd-MnOx/γ-Al2O3整体式催化剂.分别用X射线衍射(XRD)、H2-程序升温还原(H2-TPR)、低温N2吸附-脱附及X射线光电子能谱(XPS)对制备的催化剂进行表征.研究了Pd、MnOx浸渍顺序对催化剂活性、氧化还原性能及织构性质的影响.实验结果表明,Pd、MnOx共浸渍较分别浸渍制备的催化剂活性好,Pd和MnOx之间存在一定的协同作用.考察了不同载体如La-Al2O3、SiO2、γ-Al2O3和Zr-Al2O3对催化剂活性、氧化还原性能、织构性质及表面电子性能的影响.研究表明,以La-Al2O3或SiO2为载体的催化剂活性最好,即,14°C时O3转化率为82%,完全转化温度为36°C.γ-Al2O3载体次之,Zr-Al2O3载体较差.不同载体制备的催化剂中MnOx的氧化还原性能顺序为:PdMnOx/SiO2Pd-MnOx/La-Al2O3Pd-MnOx/γ-Al2O3Pd-MnOx/Zr-Al2O3.     

二苯并噻吩和吲哚在NiMoS/γ-Al2O3上加氢脱硫和加氢脱氮反应的相互影响

在固定床高压微反装置上考察了预硫化型NiMoS/γ-Al2O3催化剂上二苯并噻吩（DBT）加氢脱硫（HDS）反应和吲哚加氢脱氮（HDN）反应之间的相互影响。结果表明,吲哚对DBT的加氢脱硫反应具有抑制作用,其中对加氢路径（HYD）比对氢解路径（DDS）的抑制作用强,温度升高后,吲哚的抑制作用减弱。吲哚对DBT加氢脱硫反应的抑制作用源于吲哚及其HDN反应的中间产物在活性位上的竞争吸附。DBT和原位生成的H2S促进了催化剂表面硫阴离子空穴（CUS）向B酸位的转化,从而提高1,2-二氢吲哚（HIN）分子中C(sp3)—N键的断裂能力,使得吲哚的转化率和产物中邻乙基苯胺（OEA）的相对含量增大。HDN活性相的形成虽然需要硫原子的参与,但是活性相的保持并不需要大量的硫原子,较高含量硫化物存在时加氢活性位减少,不利于脱氮反应。     

Two-stage catalytic system of Sn/Al2O3 and Pt/Al2O3for NO reduction by propene in lean conditions

The Pt/Al₂O₃, Sn/Al₂O₃catalysts were prepared by the single sol-gel method. The two-stage Sn/Al₂O₃and Pt/Al₂O₃catalyst in series for NO reduction with propene were investigated. The coexistance of water vapor enhanced the activity at medium temperature of 300-400^oC, and the NO conversion was above 50% at 225 to 500^oC even in the presence of water vapor and SO₂. This revised version was published online in August 2006 with corrections to the Cover Date.     

Isothermal gravimetry and magnetic properties of CoOMoO3γAl2O3 catalysts

Isothermal gravimetry and magnetic susceptibility of MoO₃, MoAl₂O₃, CoAl₂O₃ and CoMoAl₂O₃ with/without Na⁺ ions have been studied in order to investigate the reducibility of the systems in H₂ H₂—hydrocarbons and H₂—hydro-carbon—thiophene. These studies have evidenced the formation of metallic cobalt during reduction of cobalt—moly catalysts containing Na⁺ ions in the Al₂O₃ support. This metallic cobalt accelerates the reduction of supported MoO₃. However, in the absence of sodium, cobalt exerts an inhibitory influence on the reduction of MoAl₂O₃. The inhibition is caused mainly due to retention of the water evolved during the process by well-dispersed Co²⁺ ions which are incapable of undergoing reduction. The presence of sulfur also kelps in suppressing the reduction to cobalt metal.