Electron spin resonance study of polymerization of butadiene with tris(acetylacetonato)titanium and triethylaluminum

ESR spectra of homogeneous catalyst derived from tris(acetylacetonato)titanium(III) and triethylaluminum were observed at several temperatures from ?78°C, to +25°C, at molar ratios of aluminum to titanium of 1–108. At ?78°C, this catalyst yields a violet complex which shows an ESR signal with a g value of 1.959 and is associated with the first intermediate. At ?40°C to ?30°C, this signal decreases, and two signals with g values of 1.947 and 1.960 are observed. The latter two signals diminish at ?5°C to +10°C, while two kinds of new signals with g values of 1.965 and 1.969 appear overlapping each other. The structures of the species corresponding to these five signals are discussed on the basis of the ESR spectra, the intensity change, and the unpaired spin distribution. A new signal with a g value of 1.978 is found in the presence of butadiene at 25°C at Al/Ti > 8 and is assigned to a growing end of polybutadiene with this catalyst. The polymer yield increases remarkedly at Al/Ti molar ratios greater than 10. The microstructure of the resulting polymer consists almost completely of 1,2 units. The structure of the growing end is proposed to be a titanium (III) species containing two 1-substituted allyl groups, by comparison with the structure ascribed to the growing end of polybutadiene with n-butyl titanate-triethylaluminum catalyst.     

Electron spin resonance study on homogeneous catalysts derived from n-butyl titanate and triethylaluminum

ESR spectra of homogeneous catalyst systems derived from n-butyl titanate and triethylaluminum at Al/Ti molar ratios of 1.0–10 were observed in toluene solution at several temperatures from ?78°C to +25°C. In the whole range of Al/Ti molar ratios, a single signal with a g value of 1.951 was observed at ?78°C and was associated with the first reaction intermediate. With increasing temperature, the intensity of the signal decreased gradually, while two series of signals appeared, depending on the Al/Ti molar ratio. At an Al/Ti molar ratio of 1.7, seven kinds of signals with g values of 1.960, 1.946, 1.950, 1.959, 1.980, 1.977, and 1.978, respectively, were observed. On the other hand, four kinds of signals with g values of 1.934, 1.966, 1.952, and 1.979, respectively, were found at Al/Ti molar ratios larger than 3. The structures of the species corresponding to the signals were discussed on the basis of the ESR spectra, the order of their growth and their hyperfine structures being considered. Two series of ESR signal were correlated to two kinds of active species for polymerization of styrene and butadiene, respectively.     

Electron spin resonance study on polymerization of conjugated dienes by homogeneous catalyst derived from n-butyl titanate and triethylaluminum

Polymerizations of butadiene, penta-1,3-diene, and isoprene with n-butyl titanate–triethylaluminum catalyst are examined by ESR measurements on the polymerization state. At Al/Ti molar ratios greater than 2.9 where the conjugated dienes are polymerized, the polymerization system of butadiene always gives an ESR signal with a g value of 1.983 and with a hyperfine structure of about 19 components. This signal does not appear at all, even in the presence of the monomer, at Al/Ti molar ratios smaller than two where butadiene is not polymerized. The absorption intensity of the signal coincides fairly well with the concentration of polymer chain calculated from polymer yield and the molecular weight. On the basis of these facts, the signal is assigned to the growing end of polybutadiene with this catalyst. The structure of the growing end is proposed to have both two substituted π-allyl groups and an alkoxy group in coordination to titanium (III), by analysis of the hyperfine structure. The polymerization system of penta-1,3-diene and that of isoprene respectively, give a new signal with a g value of 1.983, although the signal for the former monomer has a hyperfine structure of 11 components and that for the latter monomer has no hyperfine structure. A structure for the growing end in the polymerization of each of these two monomers analogous to that of the growing end of polybutadiene is proposed.     

Polymerization of n-octadecene-1 with catalysts derived from titanium tetrachloride and triethylaluminum

The effects of variation in Al/Ti mole ratio, catalyst concentration, reaction time, and temperature on the yield and some physical properties of polymers of n-octadecene-1 obtained with the use of Ziegler catalyst systems derived from titanium tetrachloride and triethylaluminum have been investigated. Results show many features similar to those obtained by other workers with lower olefins. In general, the yield of polymer shows a distinct maximum at an Al:Ti mole ratio of 2.8:1 and total catalyst concentration (at the stated mole ratio) of 4%, based on monomer; the yield increases sharply with polymerization temperature to a maximum at about 40°C. and with time up to about 12 hr. at 25°C. Polymer intrinsic viscosity also shows a strong dependence on Al:Ti mole ratio and catalyst concentration, increasing between Al:Ti mole ratios of 2.0–3.4, and showing a maximum at catalyst concentration of 3.5% on monomer. Polymer intrinsic viscosity shows a decrease with increasing reaction temperature and an increase with time of polymerization. The polymer densities, melting points, and fraction soluble in hexane (at 25°C.) appear to show much less dependence on the variables under consideration, and no firm conclusions are drawn. An important reaction concurrent with polymerization is the formation of a trans nonterminal isomer of octadecene. This certainly affects the yield (the nonterminal isomer not being polymerizable under the same conditions); the effect of the presence during polymerization of isomerized monomer on the physical characteristics of the polymer is less clear, and further work is proceeding.     

Monomer-isomerization polymerization. XIII. Monomer-isomerization polymerization of 1,4-cyclohexadiene with Ziegler-Natta catalyst

1,4-Cyclohexadiene underwent monomer-isomerization polymerization to yield poly(1,3-cyclohexadiene) with a Ziegler-Natta catalyst comprising TiCl₄–Al(C₂H₅)₃ catalyst with Al/Ti molar ratios of 0.5–3.0 at 60°C for 96 hr. Good yields of polymer were obtained (49.5% yield at Al/Ti = 3.0; [η] = 0.04 dl/g). The infrared and NMR spectra of the polymer were identical to those of poly-(1,3-cyclohexadiene), confirming that 1,4-cyclohexadiene first isomerizes to 1,3-cyclohexadiene and then homopolymerizes to give poly-1,3-cyclohexadiene. 1,3-Cyclohexadiene polymerized without isomerization easily in the presence of TiCl₃–Al(C₂H₅)₃ catalyst at Al/Ti molar ratios of 0.5–3.0 at 60°C for 3 hr (76.3% yield at Al/Ti = 3.0; [η] = 0.06 dl/g).     

Simultaneous polymerization and formation of polyacetylene film on the surface of concentrated soluble Ziegler-type catalyst solution

A direct method of simultaneously polymerizing and forming acetylene monomer to produce uniformly thin films of polyacetylene was investigated in terms of catalyst system, catalyst concentration, and polymerization temperature. The best catalyst was a Ti(OC₄H₉)₄–Al(C₂H₅)₃ system (Al/Ti = 3–4) and the critical concentration was 3 mmole/l. of Ti(OC₄H₉)₄. Below the critical concentration, only a solid or a powder was obtained. The configuration of the polymers obtained depends strongly upon the polymerization temperature. Thus an all-cis polymer was obtained at temperatures lower than ?78°C, whereas an all-trans polymer resulted at temperatures higher than 150°C. Observations either in an electron microscope by direct transmission or in a scanning electron microscope showed that the film is composed of an accumulation of fibrils about 200–300 Å in width and of indefinite length.     

Synthesis and Mechanical Properties of Polypropylene-based Polymer Hybrids via Controlled Radical Polymerization

Isotactic polypropylene-based graft copolymers linking poly(methyl methacrylate), poly(n-butyl acrylate) and polystyrene were successfully synthesized by a controlled radical polymerization with isotactic polypropylene (iPP) macroinitiator. The hydroxylated iPP, prepared by propylene/10-undecen-1-ol copolymerization with a metallocene/methyl-aluminoxane/triisobutylaluminum catalyst system, was treated with 2-bromoisobutyryl bromide to produce a Br-group containing iPP (PP-g-Br). The resulting PP-g-Br could initiate controlled radical polymerization of methyl methacrylate, n-butyl acrylate and styrene by using a copper catalyst system, leading to a variety of iPP-based graft copolymers with a different content of the corresponding polar segment. These graft copolymers demonstrated unique mechanical properties dependent upon the kind and content of the grafted polar segment.     

Polymerization of vinyl chloride by the Ti(O-n-Bu)4–AlEt3–epichlorohydrin catalyst system

The polymerization of vinyl chloride was carried out by using a catalyst system consisting of Ti(O-n-Bu)₄, AlEt₃, and epichlorohydrin. The polymerization rate and the reduced viscosity of polymer were influenced by the polymerization temperature, AlEt₃/Ti(O-n-Bu)₄ molar ratios, and epichlorohydrin/Ti(O-n-Bu)₄ molar ratios. The reduced viscosity of polymer obtained in the virtual absence of n-heptane as solvent was two to three times as high as that of polymer obtained in the presence of n-heptane. The crystallinity of poly(vinyl chloride) thus obtained was similar to that of poly(vinyl chloride) produced by a radical catalyst. It was concluded that the polymerization of vinyl chloride by the present catalyst system obeys a radical mechanism rather than a coordinated anionic mechanism.     

Stereoregularity of poly(methyl acrylate)

The stereoregularity of poly(methyl acrylate) and poly(methyl acrylate-αd) was determined from the NMR spectra. A method of quantitative determination of stereoregularity of poly(methyl acrylate) proposed in this paper is based on the fact that in the 100 Mc./sec. NMR spectrum the absorption peaks due to methylene protons in syndiotactic configurations overlap absorptions due to only one of two methylene protons in isotactic configurations. The stereostructure of poly(methy1 acrylates) polymerized with anionic catalysts such as Grignard reagents, n-butyllithium, and LiAlH₄ is generally richer in isotactic diads than in syndiotactic diads. For example, poly(methyl acrylate) polymerized with phenylmagnesium bromide as catalyst at ?20°C. consists of 99% isotactic and 1% syndiotactic diads. In radical polymerization, the isotacticity of poly(methyl acrylate) is independent of polymerization temperature. Poly(methyl acrylates) polymerized with a Ziegler-Natta catalyst consisting of Al(C₂H₅)₂Cl and VCl₄ have configurations similar to those polymerized by radical initiators. The stereoregularity of poly(methyl acrylate-α-d) resembled that of poly(methyl acrylate) polymerized under the same conditions.     

Polymerization of MMA catalyzed by different novel mixed ligand lanthanocene{(Cp)(Cl) LnSchiff-base (THF)},(COT) -Ln(methoxyethylindenyl)(THF) /Al (i -Bu)_3 systems

This article deals that the rare earth metal complexes along with Al(i'-Bu),can catalyze the polymerization of methyl-methacrylate (MMA) into high molecular weight poly(MMA) along with narrow molecular weight distributions (MWD).A typical example was mentioned in the case of {Cp(Cl) Sm-Schiff-base(THF)} which expresses maximum (conv.% = 55.46 and Mn=354×103) efficiency along with narrow MWD (Mw/Mn<2) at 60℃.The resulting polymer was partially syndiotactic (>60%).The effect of the catalyst,temperature,catalyst/MMA molar ratio,catalyst/Al( i-Bu)3 molar ratio on the polymerization of MMA at 60℃ were also investigated.     

Demonstration of isospecific free radical polymerization of acrylate controlled by conformation and chirality of monomer

Radical polymerization of lactic acid‐based chiral and achiral methylene dioxolanones, a model for conformationally s‐cis locked acrylate, was carried out with AIBN to demonstrate an isospecific free radical polymerization controlled by chirality and conformation of monomer. Polymerization of the dioxolanones proceeded smoothly without ring opening to give a polymer with moderate molecular weight and 100% of maximum isotacticity. ESR spectrum indicated a twisted conformation of the growing poly(methylene dioxolanone) radical in contrast to an acyclic analogous radical, suggesting a restriction of the free rotation around main chain C_α? C_β bond of the growing radical center. Chirality as well as the polarity and bulkiness of monomer affected the polymer tacticity, and chiral alkyl substituent would afford a high isotactic polymer, in which higher the enantiomeric excess of the monomer was, higher the isotacticity of the polymer was. While, achiral or polar substituents including dibenzyl and trichloromethyl groups would afford an atactic polymer. In addition, glass transition temperature (T_g) of the resulting polymers was significantly high, ranging from 172.2 to 229.8 °C, and even for an isotactic polymer T_g was as high as 206.8 °C. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2007–2016     

Stereoregulation in the polymerization of methyl α-ethylacrylate by n-BuLi in toluene

The polymerization of methyl α-ethylacrylate was carried out in toluene by n-BuLi at various temperatures. The yield of the polymer decreased with increase in the polymerization temperature and at 30°C and above no polymer was obtained, indicating that the ceiling temperature of this monomer lay between 0 and 30°C. The isotacticity increased with an increase in the polymerization temperature and at 0°C a highly isotactic polymer was obtained. The fractionation of the polymer obtained at ?78°C showed that the polymer was a mixture of isotactic and syndiotactic ones. Upon the addition of a small amount of methanol or water in the polymerization mixture the isotacticity of the polymer increased while the yield decreased. Syndiotactic polymer was obtained in the polymerization by n-BuLi in tetrahydrofuran as well as by diisobutyl aluminum diphenylamide in toluene.     

Cyclo- and Cyclized Diene Polymers. XIX. Polymerization of Butadiene with the C2H5AlCl2 + TiCl4 Catalyst

Abstract

The polymerization of butadiene with an EtAlCl₂-TiCl₄ catalyst system yields cyclopolybutadiene with varying amounts of trans-1, 4 units, depending upon the Al/Ti ratio and the solvent. Apparently different active centers are produced at Ti > Al and Al > Ti ratios. When the catalyst system has Ti > Al, there is a rapid decrease in the initial polymerization rate and the cyclopoly butadiene contains large amounts of methyl groups, 10–12% of trans-1, 4 units, 2–3% of 1, 2 units, and, when the polymerization is carried out in aromatic solvents, aromatic moieties are incorporated in the structure. When the catalyst system has Al > Ti, there is a very slow decrease of the initial polymerization rate, and the cyclopoly butadiene contains up to 40% of trans-1, 4 units, less than 1% of 1, 2 units, and methyl groups and solvent moieties are essentially absent even when the polymerization is carried out in aromatic solvents. Cocatalytic amounts of iodine greatly increase the initial rate of polymerization. The Ti > Al catalyst may promote 1, 3-cation-radical propagation with transoid monomer to yield a perhydrophenanthrene structure while the Al > Ti catalyst may promote 1,2 cation-radical propagation with cisoid monomer to yield a perhydroanthracene structure.     

Preparation of poly(methyl acrylate)/phosphate/composites and its possible use as storage medium for radioactive isotopes

The distribution of ¹³⁷Cs, ¹⁵²Eu, ²³⁸U, and ⁸⁵Sr in a solid/aqueous system (poly(methyl acrylate)/phosphate/composite in contact with groundwater, was investigated using γ-Spectrometry and flourometry. The results were compared with earlier results with mineral phosphate in the solid phase. The effect of contact time, pH and the concentration of concurrent element were studied. The ability of the prepared polymer composites to keep the studied radioisotopes in the solid phase is much higher than mineral phosphate. The used polymer composites have been prepared consisting of natural phosphate powder and the monomer methyl acrylate using gamma irradiation. The yield of polymerization was followed up with respect to the irradiation dose using thermogravimetric analyzer (TGA). A thermomechanical analyzer (TMA) was used to locate the area of the glass transition temperatures (T _g ) using the mode with alternative variable force; the mode with constant force was used to determine the T _g of the pure polymer and the polymer composite prepared at the same irradiation dose. The T _g of the pure poly(methyl acrylate) is 13 ± 3 °C, and the T _g of poly(methyl acrylate)/phosphate/composites is 8 ± 3 °C. The T _g were also determined using the DSC technique, and similar values were found.     

Synthesis of poly(2‐ethylhexyl acrylate)/clay nanocomposite by in situ living radical polymerization

This investigation reports the preparation of tailor‐made poly(2‐ethylhexyl acrylate) (PEHA) prepared via in situ living radical polymerization in the presence of layered silicates and characterization of this polymer/clay nanocomposite. Being a low T_g (?65 °C) material, PEHA has very good film formation property for which it is used in paints, adhesives, and coating applications. 2‐Ethylhexyl acrylate was polymerized at 90 °C using CuBr and Cu(0) as catalyst in combination with N,N,N′,N″,N″‐pentamethyl diethylenetriamine (PMDETA) as ligand. A tremendous enhancement in reaction rate and polymerization data was achieved when acetone was added as additive to increase the efficiency of the catalyst system. PEHA/clay nanocomposite was prepared at 90 °C using CuBr as catalyst in combination with PMDETA as ligand. Different types of clay with same loading were also used to study the effect on reaction rate. The molecular weight (M_n) and polydispersity index of the prepared nanocomposites were characterized by size exclusion chromatography. The active end group of the polymer chain was analyzed by ¹H NMR analysis and by chain extension experiment. Polymer/clay interaction was studied by Fourier Transform Infrared spectrometry and wide‐angle X‐ray diffraction analyses. Distribution of clay in the polymer matrix was studied by the transmission electron microscopy. Thermogravimetric analysis showed that thermal stability of PEHA/clay nanocomposite increases on addition of nanoclay. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Catalytic activity of a supported catalyst for ethylene polymerization,obtained by modification of vulcasil with titanium tetrachloride vapour

Titanium-containing surface compounds have been obtained by the interaction of the silanol groups of Vulcasil with TiCl₄ vapour. These substances have been used, in combination with organ-oaluminium and organo-magnesium compounds, for the polymerization of ethylene. The effects upon the catalyst activity of the reaction conditions (temperature, pressure, duration of polymerization), of the titanium amount on the Vulcasil surface and the Al:Ti and Mg:Ti ratios have been studied.The activity of the catalyst system has been shown to increase with increasing pressure up to 11 kg/cm² and to attain its optimum value at 60°. Polymerization has been found to end 15–20 min after the introduction of the monomer. The highest yields of polymer are obtained at Mg:Ti and Al:Ti ratios of about 30.The amount of titanium on the Vulcasil surface depends on the conditions of preliminary heat-treatment of the Vulcasil and decreases from 0.63 to 0.30 mg at/g with increasing dehydroxylation temperature. Simultaneously, the yield of polymer varies within a narrow range (89–107 g/l), and the productivity increases from 21 to 35.5 kg polyethylene (PE) per 1 g of Ti. This is especially clearly expressed with the samples obtained by preliminary heat-treatment at 400–700°.     

Polymer‐supported half‐titanocene catalysts for the syndiospecific polymerization of styrene

Monocyclopendienyltitanium trichloride (CpTiCl₃) was supported on polymer carriers with different hydroxyl contents, and the supported catalysts were used for styrene polymerization. The supported catalysts exhibited high activity even at low Al/Ti ratios and increased the molecular weight of the products, indicating that polymer carriers could stabilize the active sites. The polymers prepared with unsupported and supported catalysts were extracted with boiling n‐butanone and characterized by carbon nuclear magnetic resonance (¹³C NMR) and differential scanning calorimetry. The polymers obtained by supported catalysts had a high fraction of boiling n‐butanone‐insoluble part and high melting temperatures, but ¹³C NMR results showed that syndiotacticity decreased compared with that of polymers prepared with an unsupported catalyst. ESR study on the supported catalysts confirmed that the active sites supported on the carrier dropped into the solution and formed active sites the same as those in the unsupported system when they reacted with methylaluminoxane. ¹³C NMR analysis showed that the polymerization mechanism of the supported active sites was an active‐site controlled mechanism instead of a chain‐end controlled mechanism of the unsupported active sites. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 127–135, 2000     

Radical polymerization and copolymerization of methyl α-(2-carbomethoxyethyl)acrylate,a dimer of methyl acrylate,as a polymerizable α-substituted acrylate

Polymerization and copolymerization of methyl α-(2-carbomethoxyethyl)acrylate (MMEA), which is known as a dimer of methyl acrylate, were studied in relation to steric hindrance-assisted polymerization. The propagating polymer radical from MMEA was detected as a five-line spectrum and quantified by ESR spectroscopy during the bulk polymerization at 40–80°C. The absolute rate constants of propagation and termination (κ_p and κ_t) for MMEA at 60°C (κ_p = 19 L/mol s and κ_t = 5.1 × 10⁵ L/mol s) were evaluated using the concentration of the propagating radical at the steady state. The balance of the propagation and termination rates allows polymer formation from MMEA. The polymerization rate of MMEA at 60°C was less than that of MMA by a factor of about 4 at a constant monomer concentration. Although no influence of ceiling temperature was observed at a temperature ranging from 40 to 70°C, addition-fragmentation in competition with propagation reduced the molecular weight of the polymer. The content of the unsaturated end group was estimated to be 0.1% at 60°C to the total amount of the monomer units consisting of the main chain. MMEA exhibited reactivities almost similar to those of MMA toward polymer radicals. It is concluded that MMEA is one of the polymerizable acrylates bearing a substituted alkyl group as an α-substituent. Characterization of poly(MMEA) was also carried out. © 1996 John Wiley & Sons, Inc.     

Ligated anionic block copolymerization of methyl methacrylate with n-butyl acrylate and n-nonyl acrylate as promoted by lithium 2-(2-methoxyethoxy) ethoxide/diphenylmethyllithium

Poly(methyl methacrylate-b-n-butyl acrylate) (PMMA-b-Pn-BuA) and poly(methyl methacrylate-b-n-nonyl acrylate) (PMMA-b-Pn-NonA) diblock copolymers have been successfully synthesized by the sequential anionic polymerization of methyl methacrylate (MMA) and the n-alkyl acrylate (n-BuA or n-NonA), in a 90/10 toluene/tetrahydrofuran (THF) mixture at −78°C. When diphenylmethyllithium (DPMLi) ligated with lithium 2-(2-methoxyethoxy) ethoxide (LiOEEM) is used as the initiator, the polymerization of each block appears to be living. Molecular weight and composition of block copolymers can be predicted from the monomer over initator molar ratio and the molecular weight distribution is narrow. Size exclusion chromatography (SEC) supports that no homo-PMMA contaminates the final copolymer. Although the reverse polymerization sequence Pn-NonA-b-PMMA always results in some contamination by homo-Pn-NonA, it has no really significant effect on the final product characteristics. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1543–1548, 1997     

Stereospecific polymerization of α-methylstyrene by friedel-crafts catalysts

The relationship between stereoregularity and polymerization conditions of α-methylstyrene has been studied by means of NMR spectra. The effects of solvents and various Freidel-Crafts catalysts have been investigated. The stereoregularity of poly-α-methylstyrene increased with increased polymer solubility in the solvent used and with decreasing polymerization temperature. This behavior is completely different from the stereospecific polymerization of vinyl ethers and methyl methacrylate in homogeneous systems. This may be due to the strong steric repulsion exerted by the two substituents in the α-position of α-methylstyrene. For example, with BF₃ · O(C₂H₅)₂ as catalyst at ?78°C., atactic polymer is obtained in n-hexane, a nonsolvent for α-methylstyrene, whereas highly stereoregular polymer is produced in toluene or methylene chloride, good solvents for the polymer. However, the polarity of the solvent and the nature of the catalyst hardly affect the stereoregularity of the polymer.