La2O3掺杂TiO2光催化剂的制备和性能

采用溶胶-凝胶法制备了La2O3掺杂TiO2纳米光催化剂，并通过XRD、TEM、BET和XPS等手段进行了表征．掺入La2O3后，阻止了TiO2从锐钛矿晶型向金红石晶型的转变，使TiO2的粒径减小，比表面积增大．以甲基橙为光催化降解反应模型化合物，考察了光催化剂的活性．测定了甲基橙在纯TiO2和La2O3掺杂TiO2光催化剂上的吸附常数．考察了pH、H2O2对降解性能的影响．讨论了光催化活性与催化剂性质的关系．     

用于紫外光下氰化物光催化氧化的含硫纳米复合材料的制备和表征(英文)

A sol-gel method was used to prepare TiO_2 and sulfur-TiO_2(S-TiO_2) nanocomposites, which were characterized by N_2 adsorption-desorption, X-ray diffraction, X-ray photoelectron spectroscopy, photoluminescene, ultraviolet visible and transmission electron microscopy measurements. The photocatalytic performance of TiO_2 and S-TiO_2 nanocomposites, with respect to the photocatalytic oxidation of cyanide under visible light irradiation, was determined. The results reveal that S is well dispersed on the surface of TiO_2 nanoparticles. Additionally, the surface area of the S-TiO_2 nanocomposites was observed to be smaller than that of the TiO_2 nanoparticles because of blocked pores caused by doping with S. The S-TiO_2 nanocomposite(0.3 wt% S) exhibited the lowest band gap and the highest photocatalytic activity in the oxidation of cyanide. The photocatalytic performance of S-TiO_2(0.3 wt% S) nanocomposites was stable, even after the fifth reuse of the nanoparticles for the oxidation of cyanide.     

α-Fe_2O_3-TiO_2/SA复合半导体薄膜的制备及光催化性能的研究

应用sol gel法制备纳米α Fe2O3、TiO2及α Fe2O3 TiO2粉体,并以其作前驱体制得该纳米微粒与海藻酸钠的复合膜.由红外光谱(FT IR)、X 射线粉末衍射(XRD)、荧光光谱(PL)、透射电子显微镜(TEM)和循环伏安(I V)等物理化学方法表征、测定各复合薄膜的表面结构与催化活性.紫外 可见吸光光度法等研究结果表明,以杀菌紫外灯作光源,在纳米Fe2O3、TiO2及α Fe2O3 TiO2与海藻酸钠的复合膜悬浮液中,亚甲基蓝可被快速脱色降解,若于α Fe2O3中加入15%的TiO2,其α Fe2O3 TiO2复合晶体比单一的α Fe2O3或TiO2具有更高的光降解活性.     

Preparation of magnetic CoFe2O4-functionalized graphene sheets via a facile hydrothermal method and their adsorption properties

Magnetic CoFe₂O₄-functionalized graphene sheets (CoFe₂O₄-FGS) nanocomposites have been synthesized by hydrothermal treatment of inorganic salts and thermal exfoliated graphene sheets. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations show that cobalt ferrite nanoparticles with sizes of 10-40 nm are well dispersed on graphene sheets. OH⁻ was recognized as a tie to integrate the inorganic salts with the graphene sheets, which made reaction started and developed on the surface of graphene sheets and formed cobalt ferrite nanoparticles on graphene sheets. The adsorption kinetics investigation revealed that the adsorption of methyl orange from aqueous solution over the as-prepared CoFe₂O₄-FGS nanocomposites followed pseudo-second-order kinetic model and the adsorption capacity was examined as high as 71.54 mg g⁻¹. The combination of the superior adsorption of FGS and the magnetic properties of CoFe₂O₄ nanoparticles can be used as a powerful separation tool to deal with water pollution.     

Microwave-assisted synthesis of BiOBr/graphene nanocomposites and their enhanced photocatalytic activity

BiOBr/graphene nanocomposites were synthesized by a green single-step microwave strategy and characterized by X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy. The photocatalytic activity of the as-prepared BiOBr nanoplates and BiOBr/graphene nanocomposites for the photodegeneration of organic dyes in aqueous solution under visible light irradiation was investigated. The results show that BiOBr/graphene nanocomposites have a higher photocatalytic activity than bare BiOBr nanoplates.     

低温热处理制备石墨烯-氧化钴及其超级电容性能

采用简单的水热法制备出功能化石墨烯与CoOOH的复合物,再通过低温热处理得到功能化石墨烯-Co3O4复合材料;采用扫描电子显微镜分析了样品的形貌;测定了其电化学性能和氮气吸脱附行为.结果表明,Co3O4粒子很好地负载在石墨烯片层之间和表面;形成的复合物具有纳米孔道结构,这些纳米孔道结构有利于电解液离子的传输;而石墨烯良好的导电性有利于电子传递和提高Co3O4粒子的电容贡献值.与此同时,复合物在充放电电流密度为1A/g时的电容达320F/g,表现出优异的超电容性能.     

Nitrogen‐doped graphene‐cerium oxide (NG‐CeO2) photocatalyst for the photodegradation of methylene blue in waste water

This study shows a facile approach for the preparation of CeO₂ nanoparticles decorated with porous nitrogen‐doped graphene (NG) nanosheets for effective photocatalytic degradation of methylene blue (MB). NG nanosheets were first synthesized using a hydrothermal method and then nitrogen‐doped graphene‐cerium oxide (NG‐CeO₂) was prepared through mixing of cerium nitrate with different concentrations of NG under ultrasonication followed by hydrothermal treatment. The synthesized nanocomposites were characterized using X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and field emission scanning electron microscopy (FE‐SEM). The photocatalytic activity of the synthesized nanocomposites was analyzed against MB dye. Results showed that the nanocomposites of NG‐CeO₂ have an average particle size of 20 nm. The as‐prepared NG‐CeO₂ nanocomposites exhibited outstanding photocatalytic activity for dye degradation under visible light irradiation, which could be attributed to synergistic effects between the NG nanosheets and CeO₂. The quantum of photodegradation increases with the increase of the NG content in the nanocomposites.     

铜锡改性纳米二氧化钛光催化氧化还原性能的研究

在复合半导体基础上,采用超声浸渍法对催化剂表面作进一步铜改性,制备了铜锡改性的纳米二氧化钛光催化剂CuO_x-SnO₂/TiO₂,考察了表面铜改性、二氧化锡复合对催化剂光催化氧化还原性能的影响.结果表明,表面铜改性和复合都有利于提高催化剂光催化氧化还原能力,二者间表现出相互增强的作用.结合XRD、XPS、TEM等催化剂表征结果,对铜锡改性纳米二氧化钛光激发机制进行了讨论,提出了二氧化碳光催化还原的可能机制.     

Optimal TiO2–Graphene Oxide Nanocomposite for Photocatalytic Activity under Sunlight Condition: Synthesis,Characterization, and Kinetics

TiO₂–graphene oxide nanocomposites have been fabricated by the sol–gel technique for degradation of a typical cationic dye solution. The prepared photocatalysts were characterized by X‐ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric‐differential analyses, Brunauer–Emmett–Teller surface area measurement, and scanning and transmission electron microscopy. In addition, the photocatalytic activities of samples were evaluated by degradation of methylene blue aqueous solution under the sunlight irradiation. The change in color of solution was evaluated by the UV–vis spectroscopy, and the maximum photocatalytic decoloration (94%) was achieved within 60 min, which exceeded that of pure anatase under the same conditions. The results show that the nanocomposite containing 9.0 wt% of graphene oxide has the superior photocatalytic performance to either single‐phase anatase or other composites containing different amounts of graphene oxide. The experimental degradation data obtained from the batch tests were analyzed by a modified kinetic model, which predicted the performance with higher regression coefficients and lower relative errors. The distribution of TiO₂ nanoparticles (<20 nm) on graphene oxide sheets is proposed to be the efficient factor in the homogeneous degradation of dye which can concomitantly improve the photocatalytic activity.     

Flower-like Au/Ag/TiO_2 nanocomposites with enhanced photocatalytic efficiency under visible light irradiation

Uniform flower-like TiO_2 coated Au nanostars and core-shell Au@Ag natiostars with different amounts of Ag coating were prepared through a facile method by hydrolysis of TiF_4 under an acidic environment.The photocatalytic capability of these flower-like nanocomposites under visible light irradiation was found to be enhanced by up to 4.7-fold compared to commercial P25 TiO_2 nanoparticles.The enhanced photocatalytic activity was ascribed to improved light absorption and hot electron injection from the photo-excited Au@Ag core to the TiO_2 shell.     

层状纳米光催化复合材料H0.8Fe0.8Ti1.2O4/TiO2的合成及性质

用固相合成法制备出K0.8Fe0.8Ti1.2O4,并用离子交换反应制备出H0.8Fe0.8Ti1.2O4;通过C3H7NH2层间膨胀,TiO2粒子的插入和紫外光分解等反应,合成出一种新的层状光催化纳米复合材料-H0.8Fe0.8Ti1.2O4/TiO2.X射线衍射和漫反射等表征结果表明 该样品的层间高度为0.47nm,禁带能隙为2.18和2.88eV.用(>400 nm的光照射30 min,0.4 g样品可使甲基橙溶液(20 mg/L)的降解率达到22.1%.而同样条件下标准TiO2(P-25)仅为6.2%,表明所研制的层状纳米复合材料具有较高的光催化活性.     

Green synthesis of Copper oxide nanoparticles decorated with graphene oxide for anticancer activity and catalytic applications

Nanotechnology is an embryonic field that grips countless impacts on the drug delivery system. Nanoparticles as haulers increase the capability of target-specific drug delivery to many folds hence are used in the treatment of dreadful diseases such as cancer, diabetes, etc. This boom has aimed at, to synthesize Copper oxide nanoparticles (CuO-NPs) using Acalypha Indica leaf extract and then incorporated with graphene oxide (GO) to form GO-CuO nanocomposites. Secondly, to sightsee the photocatalytic activity of CuO-NPs and GO-CuO nanocomposites towards the decolorization of methylene blue-dye and to test its activity against HCT-116 Human colon cancer cell lines. Synthesized nanocomposites were characterized using FTIR, UV–vis, X-ray powder diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), X-ray Photoelectron Spectroscopy (XPS) and transmission electron microscopy (TEM) analysis. The photocatalytic studies revealed that synthesized nanocomposites have the efficiency to degrade methylene blue dye by 83.20% and cytotoxic activity was found to be 70% against HCT-116 Human colon cancer cell lines at 100 μg/ml. GO-CuO nanocomposites have appreciable activity towards cancer cell lines and photocatalytic activity when compared to nanoparticles as such.     

A rapid and operator-safe powder approach for latent fingerprint detection using hydrophilic Fe3O4@SiO2-CdTe nanoparticles

A new kind of bifunctional magnetic-fluorescent nanoparticles(NPs)with abundant carboxyls on the surface has been prepared by covalently combining glutathiose(GSH)-modified CdTe quantum dots(QDs)with Fe_3O_4@SiO_2NPs.The silica-coated Fe_3O_4NPs were functionalized with amino groups by(3-aminopropyl)triethoxysilane to provide Fe_3O_4@SiO_2-NH_2NPs,which was then chemically conjugated with GSH-modified CdTe QDs to form bifunctional magnetic-fluorescent NPs,Fe_3O_4@SiO_2-NH-CO-CdTe-QDs NPs.The properties and morphologies of Fe_3O_4@SiO_2-NH-CO-CdTe-QDs NPs were investigated by FTIR,X-ray diffraction,transmission electron microscopy(TEM),absorption and fluorescence spectroscopy and vibrating sample magnetometry.TEM images display that Fe_3O_4@SiO_2-NH-CO-CdTe-QDsNPs possess spherical core-shell structure with a uniform size about 50 nm.The bifunctional NPs were found to exhibit good magnetic and strong fluorescent properties favorable for their application in the detection of latent fingerprints.Furthermore,the carboxyls on the surface of NPs have good absorptions with water in air and the residues of fingerprints so as to not only avoid dust flying to protect the health of operators,but also improve the efficiency of detection.     

多壁碳纳米管负载Fe3O4磁性纳米粒子表面吸附增强过氧化酶的催化活性

采用共沉淀法制备了Fe3O4磁性纳米粒子,将其负载于氨基吡啶修饰多壁碳纳米管(MWCNT-AP)上,得到具有良好的分散性和超顺磁性的Fe3O4/MWCNT-AP复合物.通过傅里叶变换红外(FT-IR)光谱、X射线衍射(XRD)和磁滞回线测量等方法对Fe3O4/MWCNT-AP复合物进行了表征.扫描电镜(TEM)结果表明:Fe3O4磁性纳米粒子多集中于碳纳米管MWCNT-AP的端部,形成的复合物在极性溶剂中具有良好的分散性和超顺磁性;辣根过氧化酶(HRP)可通过物理作用吸附于Fe3O4/MWCNT-AP复合物表面.酸性条件下(pH 4.0),Fe3O4/MWCNT-AP复合物使HRP的最大反应速率(Vmax)提高了3倍.     

复合催化剂NdPW12O40/TiO2的制备、表征及光催化性能

 采用溶胶-凝胶法制备了NdPW12O40/TiO2复合催化剂,并用热重-差热分析、红外光谱、紫外-可见漫反射光谱、荧光发射光谱、扫描电镜和X射线衍射对催化剂进行了表征. 在紫外光照射下,以有机污染物丙酮和甲醇的气相光催化消除为模型反应,考察了催化剂的光催化活性. 结果表明, NdPW12O40的掺杂使TiO2纳米晶粒细化(粒径为11～14 nm), 表面积增大,同时有效抑制了TiO2粒子的团聚. 0.1 g 1%NdPW12O40/TiO2光催化消除初始浓度为6.58 g/m3的丙酮,空时为2.4 s时消除率可达96.74%, 达到排放要求; 催化消除初始浓度为8.82 g/m3的甲醇,空时为2.0 s时消除率可达100%, 实现完全矿化. 与纯的TiO2相比,复合催化剂吸收光的能力增强,吸收带边向长波方向延伸了20 nm.     

氮掺杂石墨烯负载的硫化镉空心球纳米复合材料的光催化性能

通过无模板法一步合成了一种新型N掺杂石墨烯负载的CdS空心球复合材料. 采用X射线衍射、透射电镜、红外光谱、紫外-可见光谱、N₂吸附-脱附、荧光光谱和X射线光电子能谱等技术对该材料进行了表征, 并在可见光照射下测试了其在降解亚甲基蓝和水杨酸中的光催化性能. 结果表明, 相对于氧化石墨烯负载硫化镉空心球和单独的硫化镉空心球, 氮掺杂石墨烯负载的硫化镉空心球具有更高的光催化活性和稳定性. 这是由于氮掺杂的石墨烯能充当优异的电子受体和传输体, 从而抑制了载流子的复合. 另外发现, 羟基自由基是可见光下降解亚甲基蓝的主要活性物种.     

TiO2/石墨烯复合材料的合成及光催化分解水产氢活性

利用石墨粉根据Hummers氧化法制得氧化石墨,并进一步还原得到石墨烯。采用溶胶-凝胶法以钛酸四丁酯和石墨烯为起始材料制备了二氧化钛(TiO₂)和石墨烯的复合光催化材料。研究了该复合材料在紫外-可见光以及可见光条件下的光催化分解水制氢活性。结果表明,紫外-可见光照射下,TiO₂/石墨烯复合光催化材料的光催化分解水产氢速率为8.6 μmol·h^-1,远大于同条件下商业P25的产氢速率 (4.5 μmol·h^-1),光解水产氢活性提高了近2倍;可见光下光照3 h,TiO₂/石墨烯复合材料的光催化分解水产氢量约为0.2 μmol。     

一种TiO2修饰的Pd/Al2O3选择性加氢用催化剂的研究

 研制了一种用TiO2修饰的Pd/Al2O3(Pd/Al2O3-TiO2)选择性加氢催化剂,并采用N2吸附,XRD,SEM,FT-IR,TPD和TPR等手段对催化剂进行了表征,考察了催化剂的催化性能. 结果表明,Pd/Al2O3-TiO2催化剂具有较小的比表面积; 低的表面酸性,且以弱酸中心为主; TiO2在Al2O3表面呈高度分散,并集中于载体到一定的深度; 用含钛溶液浸渍次数以1次为佳. 载体中TiO2的添加使得PdO更易于被还原. 用这种复合氧化物作载体制备的催化剂表现出更高的加氢活性和选择性,优于单纯以Al2O3作载体的催化剂.     

Elaboration of nano titania-magnetic reduced graphene oxide for degradation of tartrazine dye in aqueous solution

In this paper, magnetic nanocomposites are synthesized by loading reduced graphene oxide (RG) with two components of nanoparticles consisting of titanium dioxide (TiO₂) and magnetite (Fe₃O₄) with varying amounts. The structural and magnetic features of the prepared composite photocatalysts were investigated by powder X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectra (UV–vis/DRS), Raman and vibrating sample magnetometer (VSM). The resulting TiO₂/magnetite reduced graphene oxide (MRGT) composite demonstrated intrinsic visible light photocatalytic activity, on degradation of tartrazine (TZ) dye from a synthetic aqueous solution. Specifically, it exhibits higher photocatalytic activity than magnetite reduced graphene oxide (MRG) and TiO₂ nanoparticles. The photocatalytic degradation of TZ dye when using MRG and TiO₂ for 3 h under visible light was 35% and 10% respectively, whereas for MRGT it was more than 95%. The higher photocatalytic efficiency of MRGT is due to the existence of reduced graphene oxide and magnetite which enhances the photocatalytic efficiency of the composite in visible light towards the degradation of harmful soluble azo dye (tartrazine).     

微波辅助溶剂热法制备Pt/石墨烯-TiO2及其催化性能

质子交换膜燃料电池具有比能量高、结构简单、工作温度低、高效清洁和安静无摩擦等优点,是一种非常具有发展前景的电源.燃料电池借用电催化剂把燃料与氧化剂中的化学能转化为电能,通常采用碳粉负载的Pt催化剂.在燃料电池的工作环境下,碳粉载体容易腐蚀和团聚,降低了催化剂活性和稳定性,进而降低了燃料电池的使用寿命.因此,探索高稳定性的催化剂载体有利于提高催化剂的稳定性,促进燃料电池的实用化进程.为增强催化剂载体的抗腐蚀能力,一些金属氧化物如SnO2,WO3,CeO2和TiO2等被用作催化剂载体.其中,TiO2因具有稳定的化学性能以及与金属之间的"强相互作用"而备受研究者关注.但TiO2载体比表面积小和导电能力弱等缺点限制了它在燃料电池中的应用.石墨烯具有卓越的导电性和比表面积,却容易发生团聚.利用TiO2与碳材料间存在的协同作用,将TiO2与石墨烯复合来制备复合载体,能够增强TiO2的导电能力,抑制石墨烯的团聚,提高催化剂载体的化学稳定性和比表面积.本文采用微波辅助溶剂热法制备了石墨烯-TiO2复合载体和Pt/石墨烯-TiO2催化剂,研究了TiO2含量对催化剂活性和稳定性的影响.采用X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对制备的样品进行了微观结构和成分表征.结果表明,Pt/石墨烯-TiO2催化剂中TiO2为立方状纳米颗粒,粒径约为60 nm,均匀地分布在石墨烯上;Pt纳米粒子倾向于锚定在TiO2与石墨烯之间,而且分布均匀.采用线性伏安扫描(LSV)和循环伏安法(CV)测试了不同TiO2含量的Pt/石墨烯-TiO2催化剂的活性和稳定性.发现TiO2的加入确实能够提高催化剂的稳定性,随着TiO2含量的提高,催化剂稳定性增加.当TiO2含量为20%时,催化剂的起始电压与极限电流均与Pt/C催化剂接近.经过循环伏安扫描3000圈的快速老化测试后,Pt/石墨烯-TiO2催化剂起始电压的负移明显低于Pt/C催化剂,呈现了优良的稳定性和催化活性.