Preparation of Designer Resins via Living Free Radical Polymerization of Functional Monomers on Solid Support

Merrifield resin is converted to a solid-supported free radical initiator by reacting with the TEMPO-Na. Heating TEMPO-methyl resin with a variety of functionalized styrene and acrylate monomers gives larger resin beads via living free radical polymerization. We have coined the term Rasta resin to describe resin beads prepared in this fashion. The process can be described as a solvent-free suspension polymerization. It is particularly well suited for preparation of resin beads from monomers which contain electrophilic groups that would be destroyed upon suspension polymerization in water. Rasta resins have a novel macromolecular architecture wherein long straight chain polymers bearing reactive functional groups emanate from the phenyl groups of a cross-linked polystyrene core. With judicious choice of co-monomers and polymerization strategy, the solvent affinity, loading capacity, and distance of functionality from the cross-linked core may be controlled giving beads with properties that are tailored to specific uses as synthesis supports and scavenging resins.     

低交联聚苯乙烯后交联的研究(Ⅰ)

本文用氰尿酰氯为后交联剂,通过Friedel-Crafts反应使低交联聚苯乙烯发生后交联,形成大孔树脂。详细研究了反应条件对树脂孔结构的影响,所得树脂的比表面积可达500m²/g以上,孔容在0.3-0.5ml/g之间,骨架密度可达到1.3g/ml以上。树脂在不同的溶剂中有几乎相同的溶胀度。     

SWELLING AND WETTABILITY OF LIGHT-CURED METHACRYLATE-BASED DENTAL RESINS PREPARED FROM CHOLIC ACID

2 '-methacryloxy-3α, 7α 12α- trimethacryloyl cholic acid ethyl ester (CAGE4MA) has been prepared from cholic acid. Photo-polymeric resins were prepared from CAGE4MA. 2,2-bis[4-(2-hydroxy-3-methacrylyloxypropoxy)phenyl]propane (bis-GMA) was used for comparison, triethyleneglycol dimethacrylate (TEGDMA) was used as diluent. The polymerization was initiated by camphoroquinone (CQ)/N, N-dimethylaminoethyl methacrylate (DMAEMA) system. The conversion of CAGE4MA was 39% when the reaction time is 60s, which is lower than bis-GMA and TEGDMA.The swelling value of CAGE4MA resin was 0.41% in distilled water, which is much lower than those of bis-GMA resin (2.04%) and TEGDMA resin (4.77%) under the same conditions. Copolymers from CAGE4MA and TEGDMA have been prepared. With the increase of TEGDMA in mixture, the degree of conversion of CA GE4MA and swelling value increased. The swelling values of photocured resins in 0. 1mol/L HCl were also measured.     

Synthesis and application of polytetrahydrofuran-grafted polystyrene (PS-PTHF) resin supports for organic synthesis

Cross-linked polystyrene (PS) with polytetrahydrofuran (PTHF) chains were prepared for use in solid phase organic synthesis (SPOS). The resins were prepared from styrene, styrene-PTHF macromonomers and cross-linkers 1,4-bis[4-vinylphenoxy]butane or divinylbenzene by suspension polymerization. The styrene-PTHF macromonomers were prepared by cationic polymerization of 4-vinylbenzyl bromide and 4-(4-vinylphenoxy)butyl iodide activated by silver hexafluoroantimonate and 4-(5-hydroxypentyl)styrene activated by triflic anhydride. Alternatively, polytetrahydrofuran-grafted polystyrene (PS-PTHF) resins could also be directly prepared from 5-hydroxypentyl JandaJel by cationic polymerization using triflic anhydride as the initiator. These PS-PTHF resins exhibited good swelling characteristics across a wide spectrum of polar and non-polar solvents. These resins were used in the synthesis of 3-methyl-1-phenyl-2-pyrazolin-5-one, which requires β-ketoester formation at low temperature (−78 °C), resulting in good yield and product purity; whereas the same synthesis carried out on PEG-grafted PS (PS-PEG) resin resulted in incomplete synthesis.     

Cross-linked poly(4-vinylpyridine/styrene) copolymers as a support for immobilization of ytterbium triflate

Eight cross-linked poly(4-vinylpyridine/styrene) (P/S) resins (as beads) were prepared by radical suspension polymerization. Ytterbium triflate was immobilized in the range of 0.10-0.24 mmol/g by mixing with the P/S resins. The ytterbium triflate-immobilized P/S resins exhibited good activity in two Lewis acid-catalyzed reactions. Low pyridine containing resins were recycled with no loss of activity, while a slight loss of activity was observed with the higher pyridine containing resins.     

Functionalized cross-linked poly(vinyl alcohol) resins as reaction scavengers and as supports for solid-phase organic synthesis

New hydrophilic poly(vinyl alcohol) (PVA-OH) resins were prepared by an inverse suspension polymerization using epichlorohydrin as a cross-linker. These novel resins swell in a variety of solvents commonly used in solid-phase organic synthesis, such as dicholomethane, dioxane, methanol, tetrahydrofuran, and dimethylformamide. In addition, PVA-OH shows excellent swelling in water. The cross-linked PVA-OH beads were functionalized with an aldehyde group and were tested as scavengers for primary amines in three different reactions: amide bond formation, reductive amination reaction, and urea formation. With 1-2 equiv of the PVA aldehyde resin, all the excess primary amines were successfully scavenged. The utility of PVA-OH resins as solid supports in mono- and dipeptide synthesis was also investigated using symmetrical anhydride and MSNT/MeIm (2,4,6-mesitylenesulfonyl-3-nitro-1,2,4-triazolide in the presence of 1-methylimidazol) methods.     

Core-shell-type resins for solid-phase peptide synthesis: comparison with gel-type resins in solid-phase photolytic cleavage reaction

[reaction: see text] Novel core-shell-type resins with a rigid core and amino-functionalized flexible shell were prepared with 2,4,6-trichloro-1,3,5-triazine (CNC) and Jeffamine ED-600 starting from 1% cross-linked aminomethyl (AM) polystyrene resins. All of the amino groups were located outside the resin beads, and the loading capacity was 0.2-0.4 mmol/g. The amount of CNC treated was a determining factor in the properties of the final resins. The core-shell-type resins showed superior performances in terms of the initial loading of amino acid and the photocleavage reaction compared to the gel-type resins.     

基于乙炔基-苯并噁嗪单元双重交联反应的聚酰亚胺树脂的制备与性能

为开发可低温固化的聚酰亚胺树脂, 通过分子结构设计将苯并噁嗪单元引入聚酰亚胺树脂中, 合成了含苯并噁嗪单元及乙炔基封端的双官能化新型聚酰亚胺预聚体(PIBzA). 经高温处理, 苯并噁嗪单元发生开环交联, 同时, 乙炔基端基发生三聚成环反应, 从而在固化树脂中形成双重交联网络结构. 苯并噁嗪单元的引入使聚酰亚胺树脂最快固化反应温度降低约32 ℃, 有效降低了固化温度. 同时, 苯并噁嗪单元的引入未大幅度降低树脂的耐热稳定性, 其玻璃化转变温度(T_g)介于266~290 ℃之间, 5%热失重温度(T_d,5%)接近500 ℃, 依然可以满足耐高温复合材料的应用需求. 此外, PIBzA固化树脂具有低介电特性, 其介电常数k介于2.3~3.0, 介电损耗介于0.002~0.008, 可满足透波复合材料及先进微电子封装材料的应用需求.     

Tailoring ultraresins based on the cross-linking of polyethylene imines. Comparative investigation of the chemical composition, the swelling, the mobility, the chemical accessibility, and the performance in solid-phase synthesis of very high loaded resins

Ultraresins have been prepared from polyethyleneimines and cross-linking molecules and have been provided with various degrees of cross-linking. The total nitrogen loading and the loading with secondary and with tertiary amines have been determined in all products. Nitrogen loadings of the novel resins were up to 15 mmol/g, reactive secondary amines up to 13.8 mmol/g. In addition to the exceptionally high loading, the novel resins displayed efficient swelling volumes in polar and nonpolar solvents. The mobility of resin-bound species as determined by EPR-spectroscopy, depending on the amount of cross-linker, indicated good flexibility and reactivity of this resin type. The novel, high-loaded resins have been investigated subsequently in solid-phase synthesis. The Rink amide linker and two different hydroxy linkers (hydroxyacetamide, HMPB) have been attached to the resin. Despite the high loadings, the secondary amines were easily accessible and could be functionalized exhaustively. Reactivity of the linker-coupled resins was found to be closely related to the resin composition. Increased resin cross-linking led to reduced swelling, reduced mobility, and reduced reactivity in the synthesis of a medium-sized model peptide. As the result of the systematic investigation of structure-property relations in Ultraresins, a support material was identified that combined high reactivity and a mobility in the range of the extremely flexible Tentagel supports. In the optimized Ultraresin, >95% of all available secondary nitrogens could be coupled with Rink linker or with the small 2-hydroxyacetamide anchor, resulting in loadings from 2.7 to 6.8 mmol/g, respectively. A resin with an attached HMPB linker and spacer delivered analytically pure peptides in solid-phase synthesis, fully exploiting the exceptionally high loadings.     

Preparation of PVA membrane for immobilization of GOD for glucose biosensor

A membrane was prepared using polyvinyl alcohol (PVA) with low and high degree of polymerization (DOP), acetone, benzoic acid (BA) and was cross-linked by UV treatment. Membrane composition was optimized on the basis of swelling index. Membrane prepared with 12% low DOP and 8% high DOP of PVA, 2% BA, dissolved in buffer containing 20% acetone and cross-linked with UV treatment exhibited lower swelling index. Fourier transform infrared (FTIR) study of the membranes showed appearance of a strong band at approximately 2337 cm(-1) when UV was used for cross-linking in the presence of benzoic acid. Scanning electron microscope (SEM) study revealed that membrane cross-linked with UV treatment was smoother. Glucose oxidase (GOD)-PVA membrane was associated with the dissolved oxygen (DO) probe for biosensor reading. Glucose was detected on the basis of depletion of oxygen, when immobilized GOD oxidizes glucose to gluconolactone. A wide detection range, 0.9-225 mg/dl was estimated from the linear range of calibration plot of biosensor reading. Membranes were reused for 32 reactions without significant loss of activity and stored for 30 days (approximately 90% activity) at 4 degrees C. Membranes were also used with real blood samples.     

New Composite Proton-Conducting Membranes Based on Nafion and Cross-Linked Sulfonated Polystyrene

New composite membranes based on commercial perfluorinated Nafion-115 membrane and cross-linked sulfonated polystyrene were synthesized and investigated. The membranes were prepared by radical polymerization of styrene in the presence of a cross-linking agent divinylbenzene in Nafion polymer matrix and subsequent sulfonation of formed polystyrene. The membranes containing approximately 5 and 10 wt % of cross-linked polystyrene with ion-exchange capacity of 1.1 to 1.3 mg-eq/g were obtained. Modification with sulfonated polystyrene leads to an increase in the moisture content and proton conductivity of membranes in the humidity range of 15 to 100 RH.     

Investigation of Conversion of Styrene and Fumarate Double Bonds in Unsaturated Polyester Resins

The conversion of styrene and fumarate double bonds in the copolymerization of unsaturated polyesters and styrene was investigated. Several commercial polyester resins including Bisphenol-type, Iso-type and G-type resins were used. The initial fumarate double bond, the equivalent double bond per 100 g of the polyesters, was determined by the hydrogenation procedure which was developed for the present study. Using palladium-carbon catalyst and benzene-acetone (1:1) mixture, polyester resin can be hydrogenated satisfactorily.

The cured resin was extracted with chloroform. The styrene in the chloroform was determined by ASTM D-1159, bromine index method. The conversion of the fumarate double bond was calculated from the soluble part of polyester resin using the theoretical equations which were derived from the basic theory of Flory. The validity of the equations was examined by application of Funke et al.'s experimental results and found to be satisfactory. With the confidence of these results, commercial polyester resins were investigated to determine the effect of the condition of polymerization on the conversion of styrene and fumarate double bonds.

For all the polyesters the conversion of styrene was at least over 80% after a room temperature cure of 24 hr with a dimethyl anilin-cobalt naphthenate-methyl ethyl ketone peroxide three component catalyst system, and it reached approximately 100% after postcure of 100[ddot]C for 2 hr. On the other hand, the conversion of the fumarate double bond depended greatly upon the type of the resin. Bisphenol-type resin gave the highest conversion, and the conversion for Iso-type resin was higher than that for G-type resin. In the case of Bisphenol-type resin, there was no difference in the conversion of fumarate double bond between the room temperature cure and the postcure, but the conversions of fumarate double bond for G- and Iso-type resins were increased remarkably by postcure. The Barcol hardness is applicable to determine the conversion of styrene for the specified polyesters based on the relationship between the conversion of styrene and the Barcol hardness.     

SPED-(styrene-polyethyleneglycol diacrylate-9-decen-1-ol): a novel resin for solid phase peptide synthesis; synthesis and characterization of biologically potent endothelin classes of peptides

Here we present a novel beaded chemically stable, highly permeable hydrophobic/hydrophilic balanced support for solid phase peptide synthesis. The resin (SPED) was prepared by free radical suspension polymerization using monomers styrene and 9-decen-1-ol with amphiphilic cross-linking agent polyethyleneglycol diacrylate (Mn 258). Different cross-linking densities were prepared to check the extent of swelling in different polar and non-polar solvents. The SPED resin was characterized with IR, 13C NMR and surface by SEM. The chemical stability of the support in various peptide synthetic conditions was investigated and monitored by IR spectroscopy. To evaluate the applicability of the new resin in synthetic conditions more challenging peptide sequence of retro-ACP (74-65) was synthesized and compared to commercially available Merrifield resin. The efficiency of SPED was further confirmed by synthesizing biologically important endothelin family of peptides in high yield and purity. The purity of all peptides was checked by RP-HPLC and mass by MALDI-TOF MS.     

Polystyrene resins cross-linked with di- or tri(ethylene glycol) dimethacrylates as supports for solid-phase peptide synthesis

Polystyrene resins cross-linked with di(ethylene glycol) dimethacrylate (DEGDMA) and tri(ethylene glycol) dimethacrylate (TEGDMA), DEGDMA-PS and TEGDMA-PS, were synthesized by suspension copolymerization. Four functionalized resins, chloromethyl resin, 4-hydroxymethylphenoxymethyl resin (Wang resin), 4-methylbenzhydrylamine resin (MBHA resin) and 2-chlorotrityl chloride resin, were prepared from DEGDMA-PS and TEGDMA-PS. DEGDMA-PS and TEGDMA-PS showed high reactivity in the functionalization reactions in comparison with Merrifield resin (polystyrene cross-linked with divinylbenzene, DVB-PS). DEGDMA-PS-Wang resin and TEGDMA-PS-Wang resin were used as the solid-phase support for the synthesis of a difficult sequence, the fragment of acyl carrier protein 65-74. The yields of the crude peptide synthesized using DEGDMA-PS-Wang resin, TEGDMA-PS-Wang resin and DVB-PS-Wang resin were 92.3%, 91.6% and 78.8%, respectively. The purities of the crude peptides were 85.7%, 88.1% and 73.3%, respectively.     

Well-defined azlactone-functionalized (co)polymers on a solid support: synthesis via supported living radical polymerization and application as nucleophile scavengers

Wang resin has been converted to a supported initiator for transition metal-mediated living radical polymerization often called atom-transfer radical polymerization (ATRP) of 2-vinyl-4,4-dimethyl-5-oxazolone (VDM) and styrene (S). Several "Rasta" resins with well-defined macromolecular architectures, including homopolymers PVDM, PS, statistical P(S-stat-VDM), block P(S-b-VDM), and P[S-b-(S-stat-VDM)] copolymers, have been elaborated. For the homopolymerization of VDM and S, a sacrificial initiator, benzyl 2-bromoisobutyrate (BBI), has been introduced to monitor the evolution of molar masses and polydispersity indexes (PDIs) of PS and PVDM onto the Wang resin support without cleavage. After 6 h, 86.7% conversion of VDM is reached, with the isolated PVDM chains having a molar mass of 18 000 g mol(-1) and a PDI value of 1.22. Block copolymers have been synthesized in two steps, involving the synthesis of the PS block isolated at low conversions (<15%) to maintain the bromine end-chain functionality and the subsequent synthesis of the second PVDM or P(S-stat-VDM) block. Polydispersity indexes of the cleaved (co)polymers were low (PDI = 1.11-1.44), and high azlactone loadings have been reached (loading = 6.0 mmol g(-1)). Such azlactone-functionalized Wang resins have shown high efficiency during the scavenging process of benzylamine as monitored by HPLC. Moreover, grafted statistical copolymers have shown the best behavior for removing benzylamine because of an improvement of the accessibility of azlactone rings by the dilution with styrene units.     

Investigating resins for solid phase organic synthesis: the relationship between swelling and microenvironment as probed by EPR and fluorescence spectroscopy

The relationship between observed swelling of two cross-linked polystyrene resins and the microenvironment within polymer matrixes has been examined. Polystyrene cross-linked with either divinyl benzene (Merrifield resin) or 1,4-bis(4-vinylphenoxy)butane (JandaJel) was investigated with fluorescence and electron-paramagnetic resonance spectroscopy. Fluorescence spectroscopy revealed a superior correlation between observed swelling and solvation effects using a dansyl probe with JandaJel than with Merrifield resin. However, the internal viscosity of pre-swollen JandaJel is higher than Merrifield resin, as determined by EPR measurements. The combination of these two analytical methods provides insights into the physical differences observed between these two chemically similar resins and suggests caution should be used if using singular physical techniques to probe the microenvironment of polymeric matrixes.     

Development of column-pretreatment chelating resins for matrix elimination/multi-element determination by inductively coupled plasma-mass spectrometry

Chelating resins, two kinds of iminodiacetate derivatives (IDA) of cross-linked chitosan (CCS) were synthesized and investigated for adsorption capacity, matrix elimination and collection/concentration of analytes by a column pretreatment in a multi-element ICP-MS determination method. The adsorption behavior of 54 elements at the 10 ng ml(-1) level on chitosan derivatives in a packed mini-column was systematically examined. Almost 30 kinds of metal ions were recovered quantitatively at pH 5 with CCS-HP/IDA (cross-linked chitosan possessing N-2-hydroxypropyl iminodiacetic acid groups) column. Compared with available chitosan-iminodiacetate resin, CHITOPEARL CI-03, the recovery of the metal ions such as Cu, Pb and La is satisfactory with CCS-IDA (cross-linked chitosan possessing N,N-iminodiacetic acid groups) and CCS-HP/IDA using 2 M nitric acid as an eluent, which may be attributed to the difference of cross-linking and macroporous structure. Compared with Chelex-100, the adsorption efficiency is in the order: Chelex-100 > CCS-IDA > CCS-HP/IDA, especially in the chelating ability for alkaline earth metals. The resin with a longer spacer (CCS-HP/IDA) showed higher adsorption selectivity between heavy metal ions and alkaline earth metals at pH < 7. The separation efficiency of the major matrix cations in seawater (Na. K, Mg, Ca) has also been investigated, and matrix interference was negligible even in a seawater sample at pH 5 with CCS-HP/IDA. The recoveries of Mn at pH 5 with CCS-HP/IDA or Chelex-100 were almost 100%. However, those of Mg with each resin were 4 or 98%, respectively. The adsorption capacities of synthesized CCS-HP/IDA for Cu(II), Pb(II) and La(III) were 0.90, 0.65 and 0.34 mmol g(-1), respectively. Therefore, the chelating chitosan resins developed are applicable to the pretreatment of trace amounts of elements in various kinds of water samples.     

Acetylacetonyl resins for metal ion chelation

A macroreticular resin (YCH₂CHAc₂) containing acetylacetone moiety can be prepared from macroporous polystyrene (cross-linked with 6% divinylbenzene) by first chloromethylation followed by reaction with nickel, sodium or tetrabutylammonium acetylacetonate. Nickel acetylacetonate was found to be more preferable, according to the analyses of the resin by chelation tests, elemental analyses and infrared spectra. The resin YCH₂CHAc₂ can chelate with Fe³⁺ in the 58% to 87% range (from 4 mmol Fe³⁺/mL aqueous or acetone solution respectively) or with Ni²⁺ up to 0.072 mmol Ni/g resin (from 0.1 mmol Ni²⁺/mL aqueous solution). Factors, such as pH, concentration, stirring etc., which may affect chelation were investigated. Specific surfaces, thermal stability and swelling capacity of these resins have been measured.     

Polytetrahydrofuran cross-linked polystyrene resins for solid-phase organic synthesis

Currently, divinylbenzene cross-linked polystyrene (DVB-PS) is the polymer of choice for use in solid-phase organic synthesis (SPOS). While much research has been directed toward the optimization of linker groups for the attachment of compounds to the polymer, the development of new polymers themselves has been relatively neglected. In an attempt to overcome the shortcomings of DVB-PS and to develop new polymers with optimum properties for use in organic synthesis, we have prepared a series of polystyrene polymers that incorporate flexible polytetrahydrofuran (PTHF) based cross-linkers. The objective of incorporating PTHF into the polymers was to slightly increase the overall polarity of the polymer and thus render the resins more organic solvent-like. Since the degree to which a resin swells in and absorbs a particular solvent correlates to how well substrates attached to the polymer are solvated, we compared the swelling of our new resins to commercially available DVB-PS resins. In all cases, we found that our resins swelled to a much greater extent than do DVB-PS resins, and their use should therefore allow for SPOS reaction conditions that more closely mimic homogeneous solution-phase conditions. It was also found that the PTHF chain length of the cross-linker does not affect the level of swelling since all of our cross-linkers afford resins with comparable levels of increased swelling. Furthermore, we have examined the utility of our resins in directed ortho-metalation reactions and found that the increased swelling of our resins allows for isolation of reaction products in yields comparable to what is achieved using standard solution-phase conditions.     

乙基氰乙基纤维素/交联聚丙烯酸复合物膜的溶胀行为

研究了乙基氰乙基纤维素 [(E CE)C] 交联聚丙烯酸 [PAA]胆甾相液晶复合物膜的厚度以及膜的组成对膜在水中的溶胀行为的影响 .复合物膜越厚则达到溶胀平衡所需要的时间越长 ,但是其最大溶胀率是相同的 .复合物膜的最大溶胀率先是随着 (E CE)C浓度的增加而增加 ,当 (E CE)C的浓度大于 5 1wt%的时候 ,复合物膜的最大溶胀率几乎不再发生变化 .复合物膜的交联密度越大 ,其最大溶胀率越小 ,溶胀速率也随着膜的交联 (点 )密度的增加而减小 .研究还发现复合物膜的交联 (点 )密度越大 ,其溶胀前后最大选择性反射光波长的位移也越小 .