Suspensions of titania nanoparticle networks in nematic liquid crystals: rheology and microstructure

We study the influence of confinement on the rheology and structure of nematic liquid crystals (NLCs). NLCs get confined in networks of titania (TiO₂, primary particle size = 21 nm) nanoparticles in suspensions of TiO₂ and NLC, N-(4-methoxybenzylidene)-4-butylaniline (MBBA). Suspensions with TiO₂ nanoparticle volume fraction (?) of 0.006–0.017, form viscoelastic solids with low elastic modulus (G′) of 10¹ Pa–10² Pa and short relaxation times. Increase in TiO₂ nanoparticle ? leads to a rise in G′ with TiO₂ nanoparticles forming a percolating network at a critical volume fraction (? _c) = 0.023, and G′ of ~10³ Pa. TiO₂/MBBA NLC suspensions at and above ? _c = 0.023 show G′ ~ ω ^x?1 scaling, where ω is the angular frequency and the minimum in loss modulus (G′′) with ω. The effective noise temperature, x decreases and approaches 1 with the increase in the TiO₂ nanoparticle ? from 0.023–0.035, is indicative of an increase in the glassy dynamics. Through the polarized light microscopy and differential scanning calorimetry experiments, we propose that the progressive addition of TiO₂ nanoparticles introduces a quenched random disorder (QRD) in the NLC medium which disturbs the nematic order. This results in metastable TiO₂/MBBA NLC suspensions in which NLC domains get confined in the network of flocs of TiO₂ nanoparticles. We also show that the salient rheological signatures of soft glassy rheology develop only in the presence of NLC MBBA and are absent in the isotropic phase of MBBA.     

Power-law creep and residual stresses in a carbopol gel

We report on the interplay between creep and residual stresses in a carbopol microgel. When a constant shear stress σ is applied below the yield stress σ _y, the strain is shown to increase as a power law of time, γ(t) = γ ₀ + (t/τ) ^α , with an exponent α = 0.39 ± 0.04 that is strongly reminiscent of Andrade creep in hard solids. For applied shear stresses lower than some typical value σ _c ? 0.2σ _y, the microgel experiences a more complex, anomalous creep behavior, characterized by an initial decrease of the strain, that we attribute to the existence of residual stresses of the order of σ _c that persist after a rest time under a zero shear rate following preshear. The influence of gel concentration on creep and residual stresses are investigated as well as possible aging effects. We discuss our results in light of previous works on colloidal glasses and other soft glassy systems.     

Wall slip and multi-tier yielding in capillary suspensions

Impact of wall slip on the yield stress measurement is examined for capillary suspensions consisting of cocoa powder as the dispersed phase, vegetable oil as the continuous primary fluid, and water as the secondary fluid using smooth and serrated parallel plates. Using dynamic oscillatory measurements, we investigated the yielding behavior of this ternary solid-fluid-fluid system with varying particle volume fraction, ?, from 0.45 to 0.65 and varying water volume fraction, ?_w, from 0.02 to 0.08. Yield stress is defined as the maximum in the elastic stress (G^′γ), which is obtained by plotting the product of elastic modulus (G^′) and strain amplitude (γ) as a function of applied strain amplitude. With serrated plates, which offer minimal slippage, capillary suspensions with ? ≥?0.45 and a fixed ?_w =?0.06 showed a two-step yielding behavior as indicated by two peaks in the plots of elastic stress as a function of strain amplitude. On the other hand with smooth plates, the capillary suspensions showed strong evidence of wall slip as evident by the presence of three distinct peaks and lowered first yield stresses for all ? and ?_w. These results can be interpreted based on the fact that a particle-depleted layer, which is known to be responsible for slip, is present in the vicinity of the smooth surfaces. The slip layer presents itself as an additional “pseudo-microstructure” (characteristic length scale) besides the two microstructures, aqueous bridges and solid particle agglomerates, that may occur in the system. With serrated plates, both the yield stresses (σ₁σ₂) and storage moduli plateau at lower strain (before the first yield point) and at higher strain (before the second yield point) (G\(^{\prime }_{p1}\), G\(^{\prime }_{p2}\)) were found to increase with ? (at a fixed ?_w =?0.06) following power-law dependences. Similarly with increasing ?_w (0.02 – 0.08) at a fixed ? =?0.62, the system behaved as a solid-like material in a jammed state with particles strongly held together as manifested by rapidly increasing σ₁ and σ₂. The usage of smooth surfaces primarily affected σ₁ which was reflected by an approximately 70–90% decrement in the measured σ₁ for all values of ?. By contrast, σ₂ and G\(^{\prime }_{p2}\) were found to be unaffected as shown by close agreement of values obtained using serrated geometry due to vanishing slip layers at higher strain amplitudes.     

On the orders of the best approximations of integrals of functions by integrals of rank <Emphasis Type="Italic">σ</Emphasis>

We study the values e _σ(f) of the best approximation of integrals of functions from the spaces L _p (A, dμ) by integrals of rank σ. We determine the orders of the least upper bounds of these values as σ → ∞ in the case where the function ? is the product of two nonnegative functions one of which is fixed and the other varies on the unit ball U _p (A) of the space L _p (A, dμ). We consider applications of the obtained results to approximation problems in the spaces S _p ^? .     

Linearized Stability for Semiflows Generated by a Class of Neutral Equations,with Applications to State-Dependent Delays

We prove a principle of linearized stability for semiflows generated by neutral functional differential equations of the form x′(t) = g(? x _t , x _t ). The state space is a closed subset in a manifold of C ²-functions. Applications include equations with state-dependent delay, as for example x′(t) = a x′(t + d(x(t))) + f (x(t + r(x(t)))) with \({a\in\mathbb{R}, d:\mathbb{R}\to(-h,0), f:\mathbb{R}\to\mathbb{R}, r:\mathbb{R}\to[-h,0]}\).     

Multipulse Phases in k-Mixtures of Bose–Einstein Condensates

For the system

$-\Delta U_i+ U_i=U_i^3-\beta U_i\sum_{j\neq i}U_j^2,\quad i=1,\dots,k,$

(with k ≧ 3), we prove the existence for β large of positive radial solutions on \({\mathbb R^N}\) . We show that as β →  + ∞, the profile of each component U _i separates, in many pulses, from the others. Moreover, we can prescribe the location of such pulses in terms of the oscillations of the changing-sign solutions of the scalar equation  ? ΔW  +  W  =  W³. Within an Hartree–Fock approximation, this provides a theoretical indication of phase separation into many nodal domains for the k-mixtures of Bose–Einstein condensates.

     

Inviscid Models Generalizing the Two-dimensional Euler and the Surface Quasi-geostrophic Equations

Any classical solution of the two-dimensional incompressible Euler equation is global in time. However, it remains an outstanding open problem whether classical solutions of the surface quasi-geostrophic (SQG) equation preserve their regularity for all time. This paper studies solutions of a family of active scalar equations in which each component u _j of the velocity field u is determined by the scalar θ through \({u_j =\mathcal{R}\Lambda^{-1}P(\Lambda) \theta}\) , where \({\mathcal{R}}\) is a Riesz transform and Λ = (?Δ)^1/2. The two-dimensional Euler vorticity equation corresponds to the special case P(Λ) = I while the SQG equation corresponds to the case P(Λ) = Λ. We develop tools to bound \({\|\nabla u||_{L^\infty}}\) for a general class of operators P and establish the global regularity for the Loglog-Euler equation for which P(Λ) = (log(I + log(I ? Δ))) ^γ with 0 ≦ γ ≦ 1. In addition, a regularity criterion for the model corresponding to P(Λ) = Λ ^β with 0 ≦ β ≦ 1 is also obtained.     

Rheology and structural changes of plasticized zeins in the molten state

Zeins, storage proteins from maize, are suitable for making biobased thermoplastic materials. The rheological behavior of a commercial zein plasticized with 20 w% glycerol was studied in the molten state by steady-state flow experiments in extrusion conditions and oscillatory rheometry. For low residence times, a shear-thinning viscoelastic behavior was observed, with G″ exceeding G′. After 300 s at 130 °C, the complex viscosity |η ^?|?=?7?×?10³ ω ^?0.46 was found to be similar to that of thermoplastic polymer melts used in fused deposition modeling. However, the ratio between the exponents of the power laws describing G′(ω) and G″(ω) did not meet the typical value of 2 for entangled polymer melts. Moreover, for longer residence times, the viscosity increased and a gelation phenomenon was observed with a crossing over of G′(ω) and G″(ω). Gel times ranged from 6000 s at 120 °C to 1700 s at 150 °C. The evolution of the macromolecular structure assessed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis and high-performance size exclusion chromatography suggested that this gelation phenomenon involves various types of covalent and non-covalent cross-links. Disulfide bonds played a significant role in gelation kinetics despite a very low cysteine residue content in the protein primary structure (about 1 mol%). These results suggested that plasticized zeins initially behave like a low-viscosity non-entangled polymer melt, before cross-linking progressively led to a continuous network.     

Effects of Fuel Lewis Number on Localised Forced Ignition of Globally Stoichiometric Stratified Mixtures: a Numerical Investigation

The influences of fuel Lewis number Le_F on localised forced ignition of globally stoichiometric stratified mixtures have been analysed using three-dimensional compressible Direct Numerical Simulations (DNS) for cases with Le_F ranging from 0.8 to 1.2. The globally stoichiometric stratified mixtures with different values of root-mean-square (rms) equivalence ratio fluctuation (i.e. ?^′= 0.2, 0.4 and 0.6) and the Taylor micro-scale l_? of equivalence ratio ? variation (i.e. l_?/l_f= 2.1, 5.5 and 8.3 with l_f being the Zel’dovich flame thickness of the stoichiometric laminar premixed flame) have been considered for different initial rms values of turbulent velocity u^′. A pseudo-spectral method is used to initialise the equivalence ratio variation following a presumed bi-modal distribution for prescribed values of ?^′ and l_?/l_f for global mean equivalence ratio 〈?〉=1.0. The localised ignition is accounted for by a source term in the energy transport equation that deposits energy for a stipulated time interval. It has been observed that the maximum values of temperature and the fuel reaction rate magnitude increase with decreasing Le_F during the period of external energy deposition. The initial values of Le_F, u^′/S_b(?=1), ?^′ and l_?/l_f have been found to have significant effects on the extent of burning of the stratified mixtures following localised ignition. For a given value of u^′/S_b(?=1), the extent of burning decreases with increasing Le_F. An increase in u^′ leads to a monotonic reduction in the burned gas mass for all values of Le_F in all stratified mixture cases but an opposite trend is observed for the Le_F=0.8 homogeneous mixture. It has been found that an increase in ?^′ has adverse effects on the burned gas mass, whereas the effects of l_?/l_f on the extent of burning are non-monotonic and dependent on ?^′ and Le_F. Detailed physical explanations have been provided for the observed Le_F, u^′/S_b(?=1), ?^′ and l_?/l_f dependences.     

Operator method for solving the plane elasticity problem for a strip with periodic cuts

In the present paper, we use the conformal mapping z/c = ζ?2a sin ζ (a, c?const, ζ = u + iv) of the strip {|v| ≤ v ₀, |u| < ∞} onto the domain D, which is a strip with symmetric periodic cuts. For the domain D, in the orthogonal system of isometric coordinates u, v, we solve the plane elasticity problem. We seek the biharmonic function in the form F = C ψ ₀ + S ψ*₀ + x(C ψ ₁ ? S ψ ₂) + y(C ψ ₂ + S ψ ₁), where C(v) and S(v) are the operator functions described in [1] and ψ ₀(u), …, ψ ₂(u) are the desired functions. The boundary conditions for the function F posed for v = ±v ₀ are equivalent to two operator equations for ψ ₁(u) and ψ ₂(u) and to two ordinary differential equations of first order for ψ ₀(u) and ψ*₀(u) [2]. By finding the functions ψ _j (u) in the form of trigonometric series with indeterminate coefficients and by solving the operator equations, we obtain infinite systems of linear equations for the unknown coefficients. We present an efficient method for solving these systems, which is based on studying stable recursive relations. In the present paper, we give an example of analysis of a specific strip (a = 1/4, v ₀ = 1) loaded on the boundary v = v ₀ by a normal load of intensity p. We find the particular solutions corresponding to the extension of the strip by the longitudinal force X ^∞ and to the transverse and pure bending of the strip due to the transverse force Y ^∞ and the constant moment M ^∞, respectively. We also present the graphs of normal and tangential stresses in the transverse cross-section x = 0 and study the stress concentration effect near the cut bottom.     

Effect of vibration on the creep of tensile-test specimens of the aluminum alloy Al−Mg−Si (PA-4)

In this work are presented the results of research on vibrational creep at normal temperature of an aluminum alloy containing magnesium and silicon (designated PA-4). A uni-directional positive load is applied to a tensile-test specimen, such that the stress intensity in the specimen is of the type\(\sigma (t) = \sigma _m (1 + Asin\omega t)\) whereσ _m is the mean (static) stress intensity andA =σ _a /σ _m is the ratio of the vibratory-stress intensity to the mean intensity. The results are given in the form of families of curves of plastic (i.e., permanent) deformation for various values ofA, namely,A=0.0000, 0.0065, 0.05500, 0.1000 and 0.2000. Taking the creep limit for plastic strain as ε _p = 1.8 percent, equations for this creep limit were deduced from experimental data. The following conclusions are drawn from these investigations:

1. 1.
   Vibrations of small-stress-amplitude ratioA encourage creep, particularly with more lengthy tests.     
   
   

Brinkman Flow of a Viscous Fluid Through a Spherical Porous Medium Embedded in Another Porous Medium

An analytical investigation for a two-dimensional steady, viscous, and incompressible flow past a permeable sphere embedded in another porous medium is presented using the Brinkman model, assuming a uniform shear flow far away from the sphere. Semi-analytical solutions of the problem are derived and relevant quantities such as velocities and shearing stresses on the surface of the sphere are obtained. The streamlines inside and outside the sphere and the radial velocity are shown in several graphs for different values of the porous parameters \({\sigma _1 =(\mu /\tilde {\mu }) (a/\sqrt{K_1 })}\) and \({\sigma _2 =(\mu /\tilde {\mu }) (a/\sqrt{K_2 })}\) , where a is the radius of the sphere, μ is the dynamic viscosity of the fluid, \({\tilde {\mu }}\) is an effective or Brinkman viscosity, while K ₁ and K ₂ are the permeabilities of the two porous media. It is shown that the dimensionless shearing stress on the sphere is periodic in nature and its absolute value increases with an increase of both porous parameters σ ₁ and σ ₂.     

Growths of mechanical elasticity and electrical conductance of graphene nanoplatelet/poly(lactic acid) composites under strong electric field: correlation with time evolution of higher order structure of graphene nanoplatelets

For a composite of poly(lactic acid) containing graphene nanoplatelets (GNPs) at a low concentration (0.34 vol%), this study examined growths of mechanical and electrical properties under an alternating current (AC) electric field, focusing on field-induced GNP structures governing those properties. The composite was subjected to the AC field (60 Hz) of various intensities E for various times t _E at 190 °C. A fraction of randomly oriented GNPs was aligned by the field and then connected into columns, as suggested from optical microscopy. This structural evolution led to qualitatively similar growths of low-frequency storage modulus and static electrical conductivity. The key quantity for understanding this growth was a time t _E* for occurrence of short circuit that detected formation of GNP columns conductively bridging the electrodes. The growths of both modulus and conductivity for various E were summarized as functions of a reduced variable, t _E/t _E*, confirming the growths commonly reflected the evolution of the GNP columns. However, the modulus grew fast and leveled off by t _E/t _E* ~ 1, whereas the conductivity kept growing gradually even at t _E/t _E* > 1. This difference was discussed in relation to the matrix chains and leftover GNPs out the column.     

Global Attractor for a Nonlinear Oscillator Coupled to the Klein–Gordon Field

The long-time asymptotics is analyzed for all finite energy solutions to a model\(\mathbf{U}(1)\)-invariant nonlinear Klein–Gordon equation in one dimension, with the nonlinearity concentrated at a single point: each finite energy solution converges as t→ ± ∞ to the set of all “nonlinear eigenfunctions” of the form ψ(x)e^{?iω t}. The global attraction is caused by the nonlinear energy transfer from lower harmonics to the continuous spectrum and subsequent dispersive radiation.We justify this mechanism by the following novel strategy based on inflation of spectrum by the nonlinearity. We show that any omega-limit trajectory has the time spectrum in the spectral gap [ ? m,m] and satisfies the original equation. This equation implies the key spectral inclusion for spectrum of the nonlinear term. Then the application of the Titchmarsh convolution theorem reduces the spectrum of each omega-limit trajectory to a single harmonic \(\omega\in[-m,m]\).The research is inspired by Bohr’s postulate on quantum transitions and Schrödinger’s identification of the quantum stationary states to the nonlinear eigenfunctions of the coupled\(\mathbf{U}(1)\)-invariant Maxwell–Schrödinger and Maxwell–Dirac equations.     

Spray-Flame Dynamics in a Rich Droplet Array

We numerically study spray-flame dynamics. The initial state of the spray is schematized by alkane droplets located at the nodes of a face-centered 2D-lattice. The droplets are surrounded by a gaseous mixture of alkane and air. The lattice spacing s reduced by the combustion length scale is large enough to consider that the chemical reaction occurs in a heterogeneous medium. The overall spray equivalence ratio is denoted by ?_T, with ?_T = ?_L + ?_G, where ?_G corresponds to the equivalence ratio of the gaseous surrounding mixture at the initial saturated partial pressure, while ?_L is the so-called liquid loading. To model such a heterogenous combustion, the retained chemical scheme is a global irreversible one-step reaction governed by an Arrhenius law, with a modified heat of reaction depending on the local equivalence ratio. ?_T is chosen in the range 0.9 ≤ ?_T ≤ 2. Three geometries (s = 3, s = 6, s = 12) and four liquid loadings, ?_L = 0.3, ?_L = 0.5, ?_L = 0.7, ?_L = 0.85 are studied. In the rich sprays, our model qualitatively retrieves the recent experimental measurements: the rich spray-flames can propagate faster than the single-phase flames with the same overall equivalence ratio. To analyse the conditions for this enhancement, we introduce the concept of “spray Peclet number”, which compares the droplet vaporization time with the combustion propagation time of the single-phase flame spreading in the fresh surrounding mixture.     

Effects of Fuel Lewis Number on Localised Forced Ignition of Turbulent Mixing Layers

The influences of fuel Lewis number Le _F on localised forced ignition of inhomogeneous mixtures are analysed using three-dimensional compressible Direct Numerical Simulations (DNS) of turbulent mixing layers for Le _F  = 0.8, 1.0 and 1.2 and a range of different root-mean-square turbulent velocity fluctuation u′ values. For all Le _F cases a tribrachial flame has been observed in case of successful ignition. However, the lean premixed branch tends to merge with the diffusion flame on the stoichiometric mixture fraction isosurface at later stages of the flame evolution. It has been observed that the maximum values of temperature and reaction rate increase with decreasing Le _F during the period of external energy addition. Moreover, Le _F is found to have a significant effect on the behaviours of mean temperature and fuel reaction rate magnitude conditional on mixture fraction values. It is also found that reaction rate and mixture fraction gradient magnitude \(\vert \nabla \xi \vert \) are negatively correlated at the most reactive region for all values of Le _F explored. The probability of finding high values of \(\vert \nabla \xi \vert \) increases with increasing Le _F . For a given value of u′, the extent of burning decreases with increasing Le _F . A moderate increase in u′ gives rise to an increase in the extent of burning for Le _F  = 0.8 and 1.0, which starts to decrease with further increases in u′. For Le _F  = 1.2, the extent of burning decreases monotonically with increasing u′. The extent of edge flame propagation on the stoichiometric mixture fraction ξ = ξ _st isosurface is characterised by the probability of finding burned gas on this isosurface, which decreases with increasing u′ and Le _F . It has been found that it is easier to obtain self-sustained combustion following localised forced ignition in case of inhomogeneous mixtures than that in the case of homogeneous mixtures with the same energy input, energy deposition duration when the ignition centre is placed at the stoichiometric mixture. The difficultly to sustain combustion unaided by external energy addition in homogeneous mixture is particularly prevalent in the case of Le _F  = 1.2.     

Filling the gap between transient and steady shear rheology of aqueous graphene oxide dispersions

Even though the rheological behavior of aqueous graphene oxide (G-O) dispersions has been shown to be strongly time-dependent, only few transient measurements have been reported in the literature. In this work, we attempt to fill the gap between transient and steady shear rheological characterizations of aqueous G-O dispersions in the concentration range of 0.004 < ? <?3.5 wt%, by conducting comprehensive rheological measurements, including oscillatory shear flow, transient shear flow, and steady shear flow. Steady shear measurements have been performed after the evaluation of transient properties of the G-O dispersions, to assure steady-state conditions. We identify the critical concentration ? _c =?0.08 wt% (where G-O sheets start to interact) from oscillatory shear experiments. We find that the rheology of G-O dispersions strongly depends on the G-O concentration ?. Transient measurements of shear viscosity and first normal stress difference suggest that G-O dispersions behave like nematic polymeric liquid crystals at ?/? _c =?25, in agreement with other work reported in the literature. G-O dispersions also display a transition from negative to positive values of the first normal stress difference with increasing shear rates. Experimental findings of aqueous graphene oxide dispersions are compared and discussed with models and experiments reported for nematic polymeric liquid crystals, laponite, and organoclay dispersions.     

Supersonic viscous perfect-gas flow past a slender sharp elliptic cone

The supersonic M_∞ = 5 flow past slender elliptic cones with the semi-vertex angle in the plane of the major semi-axis ? _c = 4° and an isothermal surface is investigated under the assumption of the flow symmetry. Calculations on the basis of the time-dependent three-dimensional Navier-Stokes and Reynolds equations are carried out on the Reynolds number and angle of attack ranges 10⁴ ≤ Re ≤ 108 and 0 ≤ α ≤ 15° for cones with ellipticity coefficients 1/32 ≤ δ= b/a ≤ 1. The effect of the relevant parameters of the problem on the flowfield structure and the aerodynamic characteristics of the cones is demonstrated.     

Does Density Ratio Significantly Affect Turbulent Flame Speed?

In order to experimentally study whether or not the density ratio σ substantially affects flame displacement speed at low and moderate turbulent intensities, two stoichiometric methane/oxygen/nitrogen mixtures characterized by the same laminar flame speed S _L = 0.36 m/s, but substantially different σ were designed using (i) preheating from T _u = 298 to 423 K in order to increase S _L , but to decrease σ, and (ii) dilution with nitrogen in order to further decrease σ and to reduce S _L back to the initial value. As a result, the density ratio was reduced from 7.52 to 4.95. In both reference and preheated/diluted cases, direct images of statistically spherical laminar and turbulent flames that expanded after spark ignition in the center of a large 3D cruciform burner were recorded and processed in order to evaluate the mean flame radius \(\bar {R}_{f}\left (t \right )\) and flame displacement speed \(S_{t}=\sigma ^{-1}{d\bar {R}_{f}} \left / \right . {dt}\) with respect to unburned gas. The use of two counter-rotating fans and perforated plates for near-isotropic turbulence generation allowed us to vary the rms turbulent velocity \(u^{\prime }\) by changing the fan frequency. In this study, \(u^{\prime }\) was varied from 0.14 to 1.39 m/s. For each set of initial conditions (two different mixture compositions, two different temperatures T _u , and six different \(u^{\prime })\), five (respectively, three) statistically equivalent runs were performed in turbulent (respectively, laminar) environment. The obtained experimental data do not show any significant effect of the density ratio on S _t . Moreover, the flame displacement speeds measured at u′/S _L = 0.4 are close to the laminar flame speeds in all investigated cases. These results imply, in particular, a minor effect of the density ratio on flame displacement speed in spark ignition engines and support simulations of the engine combustion using models that (i) do not allow for effects of the density ratio on S _t and (ii) have been validated against experimental data obtained under the room conditions, i.e. at higher σ.     

Regularity and Singularities of Optimal Convex Shapes in the Plane

We focus here on the analysis of the regularity or singularity of solutions Ω ₀ to shape optimization problems among convex planar sets, namely:

$J(\Omega_{0})={\rm min} \{J(\Omega), \Omega \quad {\rm convex},\Omega \in \mathcal{S}_{\rm ad}\},$

where \({\mathcal{S}_{\rm ad}}\) is a set of 2-dimensional admissible shapes and \({J:\mathcal{S}_{\rm ad}\rightarrow\mathbb{R}}\) is a shape functional. Our main goal is to obtain qualitative properties of these optimal shapes by using first and second order optimality conditions, including the infinite dimensional Lagrange multiplier due to the convexity constraint. We prove two types of results:

1. i)
   under a suitable convexity property of the functional J, we prove that Ω ₀ is a W ^2,p -set, \({p\in[1, \infty]}\). This result applies, for instance, with p = ∞ when the shape functional can be written as J(Ω) = R(Ω) + P(Ω), where R(Ω) = F(|Ω|, E _f (Ω), λ₁(Ω)) involves the area |Ω|, the Dirichlet energy E _f (Ω) or the first eigenvalue of the Laplace–Dirichlet operator λ₁(Ω), and P(Ω) is the perimeter of Ω;
    

1. ii)
   under a suitable concavity assumption on the functional J, we prove that Ω ₀ is a polygon. This result applies, for instance, when the functional is now written as J(Ω) = R(Ω) ? P(Ω), with the same notations as above.