时分全分辨率可控液晶光栅设计

设计了一种可实现分光效果的可控液晶光栅.该液晶光栅由双层交错结构的驱动电极来控制液晶偏转,避免了单层控制电极之间的空白区,增加了控制面积,同时还实现了快速切换,补给了因空间分割损失的图像信息,从而使空分与时分结合实现时分全分辨率的自由立体显示.利用光刻和镀膜工艺在玻璃基板上制作氧化铟锡-二氧化硅-掺铝氧化锌双层交错结构的驱动电极,采用液晶成盒工艺将制备好的驱动电极基板和公共电极基板组装成液晶盒.光学显微镜测试表明,氧化铟锡第一电极和掺铝氧化锌第二电极的宽度为275.8μm,两者之间通过SiO2介质层隔离并相互交错覆盖在玻璃基板上.结合液晶光栅驱动电路,能有效地控制遮光区与透光区的切换,从而实现时分全分辨率可控液晶光栅.     

低压驱动高阻值层液晶透镜

针对传统电极驱动液晶透镜的电场分布在驱动电极边缘的问题,设计了一种高阻值层驱动电极来控制液晶分子偏转的低压驱动和焦距可调的液晶透镜.利用磁控溅射工艺在含镂空孔阵列的面状铝电极基板表面沉积一层掺铝氧化锌透明薄膜,形成高阻值层驱动电极;利用液晶盒成盒工艺将制备好的驱动电极基板和公共电极基板(氧化铟锡玻璃基板)组装成液晶透镜,研究掺铝氧化锌高阻值层、驱动电压、工作频率对液晶透镜光学性能的影响.实验结果表明,对比传统电极驱动液晶透镜,高阻值层电极驱动液晶透镜在驱动电压2.2Vrms和工作频率130kHz下获得的干涉圆环均匀,聚焦光斑小.同时,在驱动电压1.8～2.8Vrms和工作频率130kHz下所制备的液晶透镜焦距可调范围为4.27～2.88mm.     

柔性液晶微透镜阵列的制备与性能研究

针对集成成像视场角狭小的问题,设计并制备了一种柔性圆孔驱动电极控制液晶分子偏转的可弯曲和焦距可调的柔性液晶微透镜阵列。利用光刻技术在柔性ITO基板表面刻蚀并形成规则的圆孔阵列电极,旋涂工艺制备柔性聚酰亚胺(PI)膜层,PI膜层经60℃加热5 min后,再利用等离子体在功率630 W条件下处理5 min固化成PI取向层。利用液晶盒成盒工艺将上、下基板组装成液晶透镜,研究未弯曲和弯曲曲率半径7.5 cm条件下液晶微透镜阵列的光学性能。实验结果表明,所制备的液晶透镜在未弯曲和曲率半径为7.5 cm的情况下均可实现聚焦功能,且液晶微透镜阵列的干涉圆环均匀,聚焦光斑小。在驱动电压3~5.3 Vrms下,弯曲曲率半径为7.5 cm的液晶微透镜阵列焦距可调的范围为0.43~1.05 mm。     

基于亚波长光栅结构的硅基液晶器件模型研究

金(Au)亚波长光栅被溅射到经典硅基液晶(LCoS)的ITO电极上,它与薄液晶盒和底层铝电极组成复合共振波导结构,简称GLCoS。与基于液晶传播效应的LCoS截然不同,在GLCoS中,上电极的表面等离激元与光栅槽中的TM-FP (TM-Fabry Pérot)共振耦合,诱导一个0阶反射的相位调制;铝(Al)电极既是反射背板又与Au光栅、薄液晶盒组成波导,使共振耦合得到增强。在操控光波阵面的同时,GLCoS也作为电控器件,施加电压改变液晶的折射率,进而控制开腔FP的边缘介质条件,达到有源0~2π相位调制。实验结果表明,本文结构可用于1μm量级像素的相位空间光调制器,在高空间带宽积的全息视频显示中具有广阔的应用前景。     

紫外光诱导液晶相位光栅

使用紫外光诱导取向技术制作了可转换的液晶相位光栅,通过光掩模两次曝光的方法形成光栅条纹.这种光栅制作工艺较为简单,不需要上下基板精确的对准,驱动电压较低.采用He-Ne激光器和光探测器进行测试,结果表明,衍射效率具有电场调制性并出现同预测一致的衍射条纹.对液晶光栅的偏振特性进行了研究,利用琼斯矩阵和衍射理论对液晶相位光栅衍射强度进行了分析和模拟计算.     

具有可变电控光栅常数的液晶光栅

针对现有液晶光栅器件存在的光栅常数不能变化、电极尖端放电、边缘效应等缺点,设计了一种可转换光栅常数的液晶光栅。通过控制不同导电区的通断电,使液晶光栅不同区域产生透光与不透光,实现光栅常数的转换;液晶光栅梳状电极端部的圆弧状设计,避免了尖端放电现象,减小了边缘效应的影响。以He-Ne激光为光源,用WGD-8A型组合式多功能光栅光谱仪对所设计的液晶光栅器件进行了测量,结果表明：通过控制导电区的变化实现了光栅常数的转变,在2～3.4 V电压驱动下,具有3种不同光栅常数的液晶光栅的1级衍射光强逐渐增强,且其衍射光强的差值不断增大,达到了预期设计目的。设计的液晶光栅在视差栅栏、光栅尺等方面有好的应用前景。     

高绒度掺硼氧化锌透明导电薄膜用作非晶硅太阳电池前电极的研究

将自行研制的具有优异陷光能力的掺硼氧化锌用作p-i-n型非晶硅太阳电池的前电极,并且将传统商业用U型掺氟二氧化锡作为对比电极.相比表面较为平滑的掺氟二氧化锡,掺硼氧化锌表面大类金字塔的绒面结构会在本征层生长过程中触发阴影效应,形成大量的高缺陷材料区和漏电沟道,进而恶化电池的开路电压和填充因子.在不修饰掺硼氧化锌表面形貌的情况下,通过调节非晶硅本征层的沉积温度来消弱高绒度表面形貌引起的这种不利影响,对应的电池开路电压和填充因子均出现提升.在仅有铝背电极的情况下,在本征层厚度为200 nm的情况下,以掺硼氧化锌为前电极的非晶硅太阳电池转换效率达7.34%(开路电压为0.9 V,填充因子为70.1%,短路电流密度11.7 mA/cm2).     

不同结构的电控双折射无刻痕光栅研究

用MLC-7700-100向列相液晶制备了不同结构的电控双折射无刻痕液晶光栅.用波长为632.8 nm的He-Ne激光为光源,测量两种液晶光栅的光学衍射特性,用偏光显微镜观察不同电压下两种液晶光栅的液晶分子偏转状态和织构态改变的情况,并进行分析对比.发现双面电极条纹液晶光栅的电控衍射特性比单面电极条纹液晶光栅好.此结果...     

二元光学液晶闪耀光栅的特性分析

在二元光学理论的基础上,结合波动光学理论和液晶指向矢的计算提出一种新的二元光学液晶闪耀光栅设计.对液晶光栅电极施加阶梯分布的电压使之形成相位阶梯形分布,推导出液晶闪耀光栅的衍射效率.结果表明,通过改变周期单元光栅电极数日而改变光栅常数,可以改变光衍射角度,一级衍射角度调节范围0°～10°;调节电极电压可以使特定级次衍射光效率达到90%以上,使该级次得到闪耀.     

液晶棱镜双折射实验

介绍了液晶棱镜盒的制作及利用其测试液晶双折射的实验方法.这种棱镜盒的2片梯形透明导电玻璃的重合部分为等边三角形.不加电场时,液晶盒不是光学各向异性的单轴晶体,没有双折射现象,只能观察到散射现象;在电极上施加电压使液晶垂面排列,液晶盒成双折射单晶,利用三棱镜最小偏向角原理测试液晶双折射率.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.