光纤法布里-珀罗复合结构折射率传感器的灵敏度分析

理论上推导了光纤法布里-珀罗复合结构传感器的反射光谱条纹对比度与外界介质折射率的关系,并分析了实验参数对传感器灵敏度的影响.利用化学腐蚀渐变折射率多模光纤制作了光纤法布里-珀罗复合结构折射率传感器,空气中的条纹对比度可达30 dB以上,折射率测量的灵敏度达45 dB/RIU(refraction index unit,简RIU)以上.实验结果与理论符合很好.通过理论和实验分析,提出了进一步提高传感器灵敏度的方法. 关键词： 光纤传感器 法布里-珀罗复合结构 折射率测量 灵敏度     

基于光子晶体光纤法布里-珀罗干涉仪的温度自补偿折射率计

采用手动熔接实芯光子晶体光纤和普通单模光纤制作本征法布里-珀罗(Fabry-P6rot,F-P)干涉传感器的方法,提出了一种可实现温度自补偿的高灵敏度折射率计.理论与实验表明,新型F-P干涉传感器的对比度不受环境温度影响只随着外界折射率的变化而变化,当外界折射率在1.32～1.44范围内变化时,其折射率灵敏度约为4.59/RIU,分辨率约为2×10-5.此外,该传感器的腔长具有较高的温度灵敏度,在20～100℃范围内,其温度灵敏度为18.72 nm/℃.因此,可以通过同时监测该传感器对比度和腔长的变化就可以实现折射率和温度的同时测量,在实际工业应用中具有广泛的应用前景.     

基于激光微加工的新型光纤法布里-珀罗折射率传感器

提出了一种新型的光纤法布里-珀罗(F-P)折射率传感器,该传感器由单模光纤头端面和靠近该端面的由157 nm激光加工而成的短空气腔构成.短空气腔两个端面的反射光和光纤头端面的反射光发生干涉形成了传感器的反射谱干涉条纹.干涉条纹的对比度受光纤头端面外部的折射率影响,在干涉条纹包络的波谷处具有最大的对比度,外部待测折射率可通过计算该处的对比度得到.传感器对温度不敏感同,测量范围广.在1.33至1.441范围内,折射率灵敏度约为27 dB,分辨率约为1.12X10-4;在1.45～1.62范围内.折射率灵敏度约为24 dB,分辨率约为1.26×10-4.     

基于纤芯失配型马赫曾德尔光纤折射率和温度同时测量传感器的研究

设计和制作了一种基于单模多模细芯单模光纤马赫曾德尔(Mach-Zehnder)干涉仪结构,可同时测量折射率和温度的传感器。该传感器中,多模光纤和细芯单模熔接点充当光耦合器。导入光纤中传输的光经多模光纤后在细芯光纤的纤芯和包层中激发出纤芯模和包层模,不同模式光在细芯光纤中传输时将产生光程差,再经细芯单模熔接点耦合成为导出光纤的纤芯模而干涉。传感器透射光谱随着环境折射率和温度的变化发生漂移,通过监测不同级次的干涉谷可实现折射率和温度的同时测量。通过对传感器的透射光谱进行傅里叶变换分析可知该透射光谱主要由LP01模和LP16模干涉形成。该传感器透射光谱中1535nm附近干涉谷的折射率和温度响应灵敏度的理论值分别为-55.90nm/RIU和0.0501nm/℃(其中RIU为折射率单位);1545nm附近干涉谷的折射率和温度响应灵敏度的理论值分别为-56.26nm/RIU和0.0505nm/℃。在折射率和温度的变化范围分别为1.3449~1.3972和20℃~90℃的环境中对传感器的响应特性进行实验研究,结果表明:透射光谱中1535nm附近干涉谷的折射率和温度响应灵敏度分别为-53.03nm/RIU和0.0465nm/℃;1545nm附近干涉谷的折射率和温度响应灵敏度分别为-54.24nm/RIU和0.0542nm/℃。理论分析与实验结果相一致。该传感器在生物医学领域有较好的应用前景。     

基于光传输矩阵方法对EFFP传感器的参数优化研究

为研究光纤法珀传感器中法珀腔结构参数对其条纹对比度的影响,基于光传输矩阵方法,建立了描述非本征型光纤法珀干涉结构中光束传播特性的理论模型。以基于化学腐蚀渐变多模折射率光纤方法制作而成的光纤法珀传感器为例,进行了数值模拟。由模拟结果可以得出,腔长为40μm、曲率半径在85～115μm范围内可以获得较高的条纹对比度。其结果表明,通过优化法珀腔的腔长和形状可以改善光纤法珀传感器反射光谱的条纹对比度。     

157nm准分子激光制作的光纤珐-珀干涉折射率传感器

利用157nm激光微加工技术在单模光纤的端面加工一个微槽,用一段光纤将其密封形成一个空气珐-珀腔,这段密封用光纤与两侧的空气界面形成第二个珐-珀腔,传感器干涉条纹由两个珐-珀腔共同作用而成。计算表明,当两珐-珀腔长度接近时,传感器反射光谱的波谷位置会随着外界折射率变化而发生漂移。这种双干涉腔结构提供了一种新的折射率测量方案。实验表明当外界折射率在1．3333～1．4712内变化时,响应为非线性,平均灵敏度为28．21nm／RIU,系统折射率分辨率为3．54×10^-5,与理论计算吻合。     

基于椭球封闭空气腔的光纤复合法布里-珀罗结构折射率传感特性研究

提出了基于微椭球型空气腔的在线型光纤复合法布里-珀罗干涉结构,并对其折射率传感特性进行了研究.椭球型空气微腔是利用光纤熔接机对实芯光子晶体光纤和单模光纤以特定的熔接参数熔接形成.用高斯光束模型和ABCD法则分析了椭球型空气腔的腔内损耗,建立了电磁场在复合法布里-珀罗干涉结构中传播的物理模型.根据腔长比值的不同,环境折射率对干涉条纹的影响有对比度调制和波长调制,主要研究了一种波长调制型复合法布里-珀罗结构折射率传感器.仿真结果表明该折射率传感器在1—1.6范围内不出现折射率转折点;实验结果表明在1.333—1.466范围内,折射率灵敏度～37.088 nm·RIU-1,分辨率约为2.69×10-5.该光纤复合法布里-珀罗结构干涉条纹对比度高、体积小、成本低,用于折射率测量可靠性高、分辨率高、无折射率拐点、温度串扰小.     

一种基于马赫-曾德干涉仪的全光纤传感器双参数测量技术

提出一种干涉式全光纤传感器,能够同时实现对折射率和轴向拉力或温度进行双参数测量。传感器由一个微腔和一个纤芯失配衰减器组成。其中微腔结构是由飞秒激光加工光纤纤芯形成,直径和深度分别是6μm和2.5μm。该干涉式传感器可以获得20dB的高品质干涉对比度。传感器透射谱波长为1496.68nm和1533.18nm的两个衰减峰对应的折射率灵敏度分别为-29.91nm/RIU和-16.72nm/RIU,拉力灵敏度分别为-1.55pm/με和-0.31pm/με。实验结果表明,传感器通过灵敏度矩阵可以同时测量折射率和轴向拉力或温度两个参数。     

基于光纤锥和纤芯失配的Mach-Zehnder干涉湿度传感器

介绍了一种简单且灵敏度较高的Mach-Zehnder干涉湿度传感器.将单模光纤和多模光纤渐变熔接光纤锥,色散补偿光纤被熔接在两个多模渐变光纤之间,形成了单模光纤-光纤锥-多模渐变光纤-色散补偿光纤-多模渐变光纤-光纤锥-单模光纤结构的传感器.光纤锥起到了增加包层模能量的作用,两个多模渐变光纤节点作为光耦合器,从而形成光纤Mach-Zehnder干涉仪.外界环境湿度的变化,将使得传感器透射谱能量发生变化,通过测量干涉谱波峰峰值能量实现对湿度的测量.实验结果表明干涉谱波峰峰值能量与环境湿度之间存在良好的线性关系.当环境湿度在35%RH—85%RH范围内变化,一段由20 mm色散补偿光纤组成的传感器,其灵敏度为-0.0668 dB/%RH,相关度为0.995.该传感器结构紧凑、尺寸小、制造工艺简单,这使其可以被广泛用于湿度测量.     

一种基于马赫-曾德干涉仪的全光纤传感器双参数测量技术

提出一种干涉式全光纤传感器,能够同时实现对折射率和轴向拉力或温度进行双参数测量。传感器由一个微腔和一个纤芯失配衰减器组成。其中微腔结构是由飞秒激光加工光纤纤芯形成,直径和深度分别是6μm和2.5μm。该干涉式传感器可以获得20dB的高品质干涉对比度。传感器透射谱波长为1496.68nm和1533.18nm的两个衰减峰对应的折射率灵敏度分别为-29.91nm/RIU和-16.72nm/RIU,拉力灵敏度分别为-1.55pm/με和-0.31pm/με。实验结果表明,传感器通过灵敏度矩阵可以同时测量折射率和轴向拉力或温度两个参数。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.