高指数晶面结构氧化铁化学链燃烧反应活性及深层还原反应机理

采用密度泛函理论计算和实验研究形貌可控制备氧化铁作为高效载氧体用于化学链燃烧的可行性. 首先从理论上对比分析Fe₂O₃高指数晶面[104]和低指数晶面[001]的反应活性及深层还原反应机理. 表面反应结果显示, Fe₂O₃[104]氧化CO的反应活性远高于Fe₂O₃[001], Fe₂O₃[104]被还原成为低价的铁氧化物或单质, 这些低价的铁氧化物或单质可被O₂氧化再生. 载氧体和CO深层反应结果显示Fe₂O₃[104]可被CO彻底还原成Fe单质, Fe₂O₃[104]释放氧能力强, 反应活性高; 而Fe₂O₃[001]还原到一定程度后反应能垒高, 抑制表面进一步还原, 释放氧能力有限. 最后, 实验结果进一步证明了Fe₂O₃[104]作为载氧体用于化学链燃烧的高反应活性及稳定性.     

Fe1-xO基氨合成催化剂的制备化学

采用高温熔融法制备了各类铁氧化物,用XRD分析了熔融过程中的物相变化,EOS考察了熔融体凝固-冷却速率对助催化剂分布的影响.结果表明,采用大气气氛中的高温熔融法不能制取Fe₂O₃和化学计量比的FeO,前者会发生分解反应,后者会发生歧化反应;在1.333≤n(O)/n(Fe)<1.38范围时,可以制取Fe₃O₄或非化学计量比的Fe₃-yO₄;在1.113O₄和FeO的混合氧化物;在1.0451-xO,即维氏体.Fe_1-xO基催化剂的制备必须采用物理熔融与化学反应相结合的工艺.凝固冷却速度对抑制氧化亚铁的氧化反应和歧化反应,保证助催化剂的均匀分布和晶粒度均有很大影响     

还原气氛对CoFe/SBA-15催化剂F-T反应性能的影响

考察了不同还原气氛处理CoFe/SBA-15催化剂对F-T反应性能的影响。结果表明,H2气氛下有利于六方钴的生成;催化剂的活性取决于钴含量,随着钴含量的增加,F-T反应中CO转化率增加,C5+选择性增加。随着铁含量的增加,催化剂表现了较高的CO2选择性。CO还原有利于立方钴的生成,导致催化活性相比H2还原的催化剂活性要低。同时CO还原容易产生积炭使催化剂的钴活性位被覆盖,导致甲烷选择性随着钴含量增加而升高。但碳化铁的生成有利于提高20Fe/SBA-15催化剂的活性,有利于低碳烃生成及C2~4烃烯烷比增加。     

Fe3O4矿石球团焙烧化学的穆斯堡尔效应研究

应用穆斯堡尔效应实验对焙烧过程中球团的矿相变化及铁离子的赋存情况进行了研究,进一步了解了焙烧化学。     

化学链制氢中Fe2O3/LaFeO3载氧体的性能研究

采用柠檬酸络合法制备Fe₂O₃/LaFeO₃复合氧化物,将该氧化物作为化学链制氢过程的载氧体,在反应温度为900 ℃、常压下,对Fe₂O₃/CH₄（剂烷比）、进水量、金属负载量进行了考察。结果表明,剂烷比为2：1、进水量为0.1 mL、质量分数15%Fe时载氧体性能最好,甲烷转化率达到60%,单次循环氢气产量为45 mL。将该评价结果与XRD和H₂-TPR表征结果进行关联发现,反应过程的活性位不是金属氧化物,而是吸附氧,而且吸附氧越容易还原,甲烷转化率和氢气产量越高。通过连续60次还原-氧化循环发现,该载氧体上甲烷转化率和氢气产量比较稳定,循环后仍然保持钙钛矿结构。     

氧化铁负载铂纳米簇催化卤代硝基苯本体氢化性质研究

复相金属催化剂中的载体效应研究具有重要意义。我们以结构不同的氧化铁载体吸附"非保护型"Pt金属纳米簇制备了具有相同Pt纳米簇的Pt/Fe_3O_4、Pt/γ-Fe_2O_3和Pt/α-Fe_2O_3催化剂,考察了其在无溶剂条件下(本体条件)催化邻氯硝基苯(o-CNB)选择性氢化反应的性能,发现三种铂/氧化铁催化剂的催化选择性远高于商购铂/碳催化剂,Pt/γ-Fe_2O_3和Pt/α-Fe_2O_3的催化选择性明显高于Pt/Fe_3O_4,而Pt/Fe_3O_4的催化活性较Pt/α-Fe_2O_3高50%。铂/氧化铁对不同卤代硝基苯的本体选择性氢化反应表现出优良的催化性能,相应卤代苯胺产物的选择性均可达到99%以上。考察了温度、氢气压力对Pt/Fe_3O_4催化o-CNB本体氢化性能的影响。本工作为理解氧化铁负载金属纳米簇催化剂的特殊催化性质,进而发展高效金属纳米簇基催化体系提供了新的基础。     

The electrolyte NRTL model and speciation approach as applied to multicomponent aqueous solutions of H2SO4, Fe2(SO4)3, MgSO4 and Al2(SO4)3 at 230–270 °C

This work presents chemical modeling of solubilities of metal sulfates in aqueous solutions of sulfuric acid at high temperatures. Calculations were compared with experimental solubility measurements of hematite (Fe₂O₃) in aqueous ternary and quaternary systems of H₂SO₄, MgSO₄ and Al₂(SO₄)₃ at high temperatures. A hybrid model of ion-association and electrolyte non-random two liquid (ENRTL) theory was employed to fit solubility data in three ternary systems H₂SO₄–MgSO₄–H₂O, H₂SO₄–Al₂(SO₄)₃–H₂O at 235–270 °C and H₂SO₄–Fe₂(SO₄)₃–H₂O at 150–270 °C. Employing the Aspen Plus™ property program, the electrolyte NRTL local composition model was used for calculating activity coefficients of the ions Al³⁺, Mg²⁺ Fe³⁺ and SO₄²⁻, HSO₄⁻, OH⁻, H₃O⁺, respectively, as well as molecular species. The solid phases were hydronium alunite (H₃O)Al₃(SO₄)₂(OH)₆, hematite Fe₂O₃ and magnesium sulfate monohydrate (MgSO₄)·H₂O which were employed as constraint precipitation solids in calculating the metal sulfate solubilities. A correlation for the equilibrium constants of the association reactions of complex species versus temperature was implemented. Based on the maximum-likelihood principle, the binary interaction energy parameters for the ionic species as well as the coefficients for equilibrium constants of the reactions were obtained simultaneously using the solubility data of the ternary systems. Following that, the solubilities of metal sulfates in the quaternary systems H₂SO₄–Fe₂(SO₄)₃–MgSO₄–H₂O, H₂SO₄–Fe₂(SO₄)₃–Al₂(SO₄)₃–H₂O at 250 °C and H₂SO₄–Al₂(SO₄)₃–MgSO₄–H₂O at 230–270 °C were predicted. The calculated results were in excellent agreement with the experimental data.     

SO_4~(2-)功能化处理对Fe_2O_3催化剂上氨选择性催化还原NO_x性能的促进机理研究

采用沉淀法制备了Fe(OH)_3和Fe_2O_3。通过硫酸化处理得到SO_4~(2-)/Fe(OH)_3和SO_4~(2-)/Fe_2O_3两种催化剂,并将其应用于氨选择性催化还原NO_x(NH_3-SCR)反应,研究了SO_4~(2-)功能化处理对Fe_2O_3催化剂上NH_3-SCR脱硝性能的促进机理。结果表明,与纯的Fe_2O_3相比,硫酸化处理得到的催化剂上SCR活性得到显著提升;其中,SO_4~(2-)/Fe(OH)_3表现出更加优异的催化性能,在250-450℃时NO_x转化率高于80%,且具有优异的稳定性和抗H_2O+SO_2性能。XRD、Raman、TG、FT-IR、H_2-TPR、NH_3-TPD和in situ DRIFTS等表征结果显示,硫酸功能化处理能抑制Fe_2O_3的晶粒生长,同时SO_4~(2-)与Fe~(3+)结合形成硫酸盐复合物,提高了催化剂表面酸性位点的数量和酸强度,抑制了Fe_2O_3上的氨氧化反应,从而提高了其脱硝催化性能。     

静电自组装方法合成的具有多孔三维网络结构的Fe_3O_4/石墨烯复合材料作为高性能锂离子电池负极材料(英文)

采用静电自组装方法,分两步合成Fe(OH)3/GO前驱体(GO:氧化石墨烯),再通过水热反应和600°C高纯氮气气氛下煅烧,获得了Fe3O4/石墨烯复合材料.通过X射线衍射(XRD)、扫描电镜(SEM)、高分辨透射电镜(HRTEM)、拉曼(Raman)光谱等多种分析,发现该复合材料具有三维多孔石墨烯网络结构.把合成的这种Fe3O4/石墨烯复合材料作为锂离子电池负极材料,电化学测试结果表明其具有优良的电化学性能:首次放电容量为1390 mAh·g-1,50次循环后容量为819 mAh·g-1.通过对比实验表明,三维石墨烯网络结构的形成对复合材料的电化学循环稳定性起着关键作用.     

理想与还原Fe2O3[001]表面上汞吸附协同催化CO分解作用

煤化学链燃烧必然释放汞,汞与载氧体表面相互作用,影响表界面的氧化还原反应。本文采用密度泛函理论计算,研究汞（Hg⁰）在理想表面（Fe₂O₃[001]）和一系列被还原表面（Fe₂O_2.75、Fe₂O_2.5、Fe₂O_2.25、Fe₂O_1.625、Fe₂O_0.875、Fe₂O_0.375和Fe）的吸附,以及Hg⁰对Fe₂O_1.625、Fe₂O_0.875、Fe₂O_0.375和Fe等表面催化CO分解反应的协同作用机理。Hg⁰物理吸附在理想Fe₂O₃[001]表面。随着Fe₂O₃[001]表面不断被还原,Hg⁰发生化学吸附。Hg⁰吸附降低了CO与Fe₂O₃、Fe₂O_2.75、Fe₂O_2.5和Fe₂O_2.25等表面之间的相互作用,抑制O传递氧化CO为CO₂的反应;载氧体进一步还原过程中,Hg⁰吸附促进了CO与Fe₂O_1.625、Fe₂O_0.875、Fe₂O_0.375及Fe等表面之间的相互作用,进而促进了表面对CO的催化分解反应,加速了载氧体表面的积碳,降低了化学链燃烧效率。因此,合理控制载氧体的还原程度既可以减弱Hg⁰的吸附,也可以抑制积碳的形成,这对化学链燃烧的操作优化至关重要。     

Study of an iron-based Fischer–Tropsch synthesis catalyst incorporated with SiO2

The effect of adding SiO₂ to a precipitated iron-based Fischer–Tropsch synthesis (FTS) catalyst was investigated using N₂ physical adsorption, H₂ differential thermogravimetric analysis, temperature-programmed reduction/desorption (TPR/TPD) and Mössbauer spectroscopy. The FTS performances of the catalysts with or without SiO₂ were compared in a fixed bed reactor. The characterization results indicated that SiO₂ facilitates the high dispersion of Fe₂O₃ and significantly influences the Fe/Cu and Fe/K contacts, which play an important role in the surface basicity, reduction and carburization behaviors, as well as the FTS performances. The incorporation of SiO₂ enhances the Fe/Cu contact, further enlarges the H₂ adsorption and promotes the reduction of Fe₂O₃ → FeO_x, while the transformation of FeO_x → Fe is suppressed probably due to the strong Fe–SiO₂ interaction. SiO₂ indirectly weakens the surface basicity and severely suppresses the carburization and CO adsorption of the catalyst. In the FTS reaction, it was found that SiO₂ decreases the FTS initial activity but improves the catalyst stability. Due to the lower surface basicity than the catalyst without SiO₂, the catalyst incorporated with SiO₂ has higher selectivity to light hydrocarbons and methane and decreased selectivity to the olefins and heavy hydrocarbons.     

Ultraviolet Light Assisted Hierarchical Porous Fe2O3 Catalyzing Heterogeneous Fenton Degradation of Tetracycline Under Neutral Condition with a Low Requirement of H2O2

The hierarchical porous Fe2O3 particles as a novel ultraviolet light assisted heterogeneous Fenton catalysts were synthesized by bio-template synthesis method using iron nitrate as precursor at high temperature of around 550℃.The hierarchical porous structured Fe2O3 was endowed with a large surface area and abundant pore volume,leading to the exposure of more active sites and rapid mass transfer.The synergistic effect of UV irradiation and hie-rarchical porous Fe2O3 improved the photo-degradation efficiency of Tetracycline(TC).The degradation efficiency of Fe203 catalyzing UV-Fenton system reached 97.4%after 60 min reaction,which was more substantial than Fe2O3 catalyzing Fenton system(7.6%)and UV/H2O2 system(59.2%).Moreover,the hierarchical porous Fe2O3 catalyzing UV-Fenton system exhibited an extremely wide pH range(from 3.0 to 9.0,from mildly acidic to slightly alkaline)for efficient degradation of TC.Simultaneously,the extraordinary higher degradation efficiency was based on 10 mmol/L H2O2 concentration,which was low requirement for H2O2,Further,the hierarchical porous Fe2O3 can be used for five consecutive cycles with over 95%of the original degradation efficiency.Ultraviolet light assisted heterogeneous Fenton reaction in the hierarchical porous Fe2O3 improved the·OH and O2·^-production and Fe(III)/Fe(II)redox cycle,which consequently achieved an excellent degradation rate.     

Pd/Fe3O4-C催化剂对甲醇、乙醇和丙醇氧化的电催化活性

制备对醇氧化反应具有优异电活性的钯催化剂是醇燃料电池研究的重要内容。本文用硼氢化钠还原法制备了钯纳米颗粒, 然后沉积在Fe3O4/C复合物表面, 得到了不同Fe₃O₄负载量的Pd/Fe₃O₄-C催化剂. 透射电镜（TEM）图显示钯纳米颗粒均匀地分散在Fe₃O₄/C表面. 对制备好的Pd/Fe₃O₄-C催化剂进行了循环伏安法（CV）、计时电流（CA）和电化学阻抗谱（EIS）的测试, 研究了其在碱性介质中对C1-C3醇类（甲醇、乙醇和丙醇）氧化的电催化活性. 结果表明, 所制备的不同Fe₃O₄负载量的Pd/Fe₃O₄(2%)-C,Pd/Fe₃O₄(5%)-C, Pd/Fe₃O₄(10%)-C和Pd/C催化剂中, Pd/Fe₃O₄(5%)-C催化剂表现出最高的醇氧化电流密度. 依据循环伏安（CV）数据,Pd/Fe₃O₄(5%)-C催化剂对甲醇、乙醇、正丙醇和异丙醇氧化的阳极峰电流密度分别是Pd/C催化剂的1.7、1.4、1.7和1.3倍. Pd/Fe₃O₄(5%)-C催化剂对乙醇氧化的电荷传递电阻也远低于Pd/C催化剂. 制备的所有催化剂对C1-C3醇类电氧化的电流密度大小排序如下: 正丙醇﹥乙醇﹥甲醇﹥异丙醇. 此外, 碳粉中Fe₃O₄纳米颗粒的存在提高了钯纳米颗粒的电化学稳定性.     

Relationship between temperature-programmed reduction profile and activity of modified ferrite-based catalysts for WGS reaction

A series of modified ferrites were prepared by doping iron oxide with various transition/non-transition/inner-transition metal ions [M = Cr, Mn, Co, Ni, Cu, Zn and Ce] in situ during synthesis. All the modified ferrites thus obtained exhibit remarkably high surface areas, greater than that of pure iron oxide (Fe₂O₃) sample. The efficacy of the dopant ions in modifying the resultant specific surface area, could be directly related to variations in the rate of crystal growth. The nature and concentration of the foreign cations present in the system govern this variation. Interestingly all the modified ferrites, exhibit a narrow pore size distribution in the range of 4.9–25 nm. XRD analysis revealed the existence of hematite (Fe₂O₃) phase in all the as-prepared samples. The X-ray diffraction experiments performed on activated catalysts, confirmed the existence of magnetite (Fe₃O₄) phase with a nominal composition of Fe_2.73M_0.27O₄. These inverse or mixed spinels with general formula A_(1−δ)B_δ[A_δB_(2−δ)]O₄, possess highly facile Fe³⁺  Fe²⁺ redox couple, the degree of facileness depends on the extent of synergistic interaction between iron and the other substitutent metal ion. The rapid electron hopping between Fe³⁺  Fe²⁺ in the Fe₃O₄ lattice system is essential to catalyze WGS reaction. From TPR it was observed that, incorporation of metal cations into the hematite (-Fe₂O₃) crystal structure alters the reducibility of the hematite particles, which in turn depends on the nature of the incorporated metal cation. A plausible explanation for the WGS activity over various modified ferrites has been attempted with the help of TPR analysis.     

Effects of oxidation pretreatment temperature on Kovar used as CO_2 reforming catalyst

The effect of oxidation pretreatment temperature(500 ~ 1 000 ℃) on the catalytic activity of Kovar applied on hydrocarbon CO2reforming was examined. Catalytic performance evaluation using tetradecane at 800 ℃ with 70 μmol/s CO2revealed 700 and 1 000 ℃ as the best pre-oxidation temperature in producing CO and H2,respectively. XRD and SEM-EDX analyses showed that a separate metal oxide layer composed of iron oxide(Fe2O3and F3O4),nickel,cobalt,and possibly their respective oxides started to form when oxidation was conducted at 700 ℃ or higher.The presence of iron enhanced the stability of nickel in the structure while the compact structure of Fe3O4resulted into the formation of a thick and rigid metal oxide layer on the surface of the Kovar tube. The strong physical bond between the metal oxide layer and Kovar tube provided the catalyst good mechanical strength and consequently good catalytic activity.     

水热法制备Fe3O4/rGO纳米复合物作为锂离子电池阳极材料

以氢氧化铁为四氧化三铁的前驱体,氧化石墨烯（GO）为还原石墨烯（rGO）的前驱体,以水合肼和二水合柠檬酸三钠为混合还原剂,采用水热法制备了还原石墨烯负载四氧化三铁纳米颗粒（Fe₃O₄/rGO）的复合材料。通过透射电子显微镜（TEM）、X-射线衍射（XRD）和热重分析（TGA）对产物的形貌、结构和组成进行了表征。以锂片为对电极进行了扣式电池的组装,通过恒电流充放电和循环伏安法对其电化学性能进行了测试。材料具有均一的形貌,rGO具有较高的还原程度且可以在充放电过程中缓冲Fe₃O₄纳米颗粒的体积变化,使得Fe₃O₄/rGO纳米复合物具有较好的电化学性能。     

An unexpected generation of magnetically separable Se/Fe3O4 for catalytic degradation of polyene contaminants with molecular oxygen

Selenization of Fe₂O₃ with NaHSe led to Se/Fe₃O₄. The unexpected generation of Fe₃O₄ attributed to the reduction conditions of the reaction, and the resulted magnetic features of the material facilitated its separation in practical applications. Owning to the synergistic effect of Se with Fe, the material was especially active to catalyze the oxidative C=C scission using O₂ as mild oxidant. The technique has been successfully applied in polyene degradation project, which is of profound practical values for the treatment of the polyene pigment pollution and may be applied in the food and pharmaceutical industry.     

Surface Modifications of Halloysite Nanotubes with Superparamagnetic Fe3O4 Nanoparticles and Carbonaceous Layers for Efficient Adsorption of Dyes in Water Treatment

Surface modification of halloysite nanotube(HNT) with in situ grown Fe₃O₄ nanoparticles and carbonaceous layers introduced by a hydrothermal carbonization process of glucose has been achieved. Structure and morphology investigations demonstrate that iron oxide nanoparticles are uniformly anchored on the halloysite and prevent the aggregations of halloysite and carbon, forming a protective layer that stabilizes and improves the property of HNT/Fe₃O₄/C nanocomposite. Magnetism characterization proves the superparamagnetic behavior of HNT/Fe₃O₄/C hybrid at room temperature, which makes it easily separated from dye solution under an external magnetic field. Exploration of adsorption ability demonstrates that the maximum adsorption capacity of the as-prepared HNT/Fe₃O₄/C nanocomposite for methylene blue(MB) is about twice and 1.5 times those of HNT/Fe₃O₄ and HNT according to Langmuir equation, respectively. The adsorption behavior investigations indicate that HNT/Fe₃O₄/C hybrid has a heterogeneous structure and shows a non-ideal monolayer adsorption that fits the Redlich-Peterson isotherm, and the adsorption process follows a pseudo-second-order kinetic model. Therefore, the as-prepared HNT/Fe₃O₄/C hybrid is a fast, separatable and superparamagnetic adsorbent with a good adsorption ability, demonstrating great potential in the application of water treatment.     

三维多级孔类石墨烯载三氧化二铁锂离子电池负极材料

采用简单的水解、热处理方法合成三氧化二铁（Fe₂O₃）负载在三维多级孔类石墨烯（3D HPG）上的复合材料. 3D HPG有效的导电网络有利于负载纳米Fe₂O₃,使其呈均匀分散状态,并有效增强纳米复合物的导电率,提高Fe₂O₃利用率,抑制纳米Fe₂O₃的团聚,从而制得稳定、高性能的锂离子电池负极材料. Fe₂O₃-3D HPG电极在50 mA·g^-1电流密度下首次放电容量达1745 mAh·g^-1,50周期放电容量保持于1095 mAh·g^-1.     

煤化学链燃烧Fe2O3载氧体的反应性研究

利用流化床反应器并以水蒸气作为气化-流化介质,研究了温度、反应时间、循环数对Fe₂O₃载氧体反应性的影响。实验表明,载氧体与煤气化产物的反应性随温度升高而增强,且温度越高,反应受化学反应控制时间越短。当温度高于900℃时,煤中碳转化为CO₂的比率大于90%,载氧体体现了很好的反应性,但反应温度低于850℃时,比率小于75%。反应温度900℃时,CO₂干基浓度随循环数而逐渐降低,CO、CH₄浓度增加,且CH₄浓度值大于CO。利用XRD、SEM分析了固体反应产物成分与微观形态结构。分析表明,Fe₂O₃的还原产物为Fe₃O₄,载氧体颗粒随循环数增加而逐渐烧结。