The effect of molecular weight of polymer matrix on properties of polymer-dispersed liquid crystals

The electro-optical properties and memory effects are important characters of polymer-dispersed liquid crystal (PDLC) devices. Molecular weight of polymer matrix influences the morphology of liquid crystal droplets in PDLC film and the performance of PDLC devices. In this letter, PDLC films were doped with a small amount of chain transfer agent (CTA), in order to control the molecular weight of polymer matrix. It is observed that the addition of CTA induces a reduction of threshold voltage. In addition, the effect of molecular weight on memory effects of PDLC devices was also discussed. It is found that the entanglement between polymer and liquid crystal molecule increased with the molecular weight, which reduces the memory effect.     

Relaxation time of polymer ball type PDLC films

“Polymer ball” polymer dispersed liquid crystal (PDLC) samples were fabricated by the photo-polymerization induced phase separation method and their relaxation behaviour was studied. It was found that upon removal of the applied electric field, the transmittance of the “polymer ball” PDLC sample decays exponentially from T_on to T_memo with a relaxation time constant in the order of msec. It was found that the measured relaxation time constant decreases as the curing time increases and the LC concentration increases.     

固化条件对聚合物分散液晶膜电光性能的影响

选用聚乙二醇二缩水甘油醚(EGDE)/季戊四醇缩水甘油醚(PERTGE)/1,8-二氨基-3,6-二氧杂辛烷(EDBEA)/向列相液晶(SLC1717)复合体系,在不同的固化条件下,通过热聚合诱导相分离方法制备了一系列电光性能不同的聚合物分散液晶(polymer dispersed liquid crystal,简称PDLC)膜.研究了固化温度和固化时间对制备的PDLC膜中聚合物网络的微观形貌和电光性能的影响.结果表明,随着固化温度的升高以及固化时间的缩短,PDLC膜的对比度、驱动电压和开态响应时间逐渐增大,而关态响应时间逐渐减小.在固化温度为363.2 K,固化时间为7 h时,所制备的PDLC膜具有较佳的电光性能.     

The fabrication of polymer dispersed liquid crystal based on SiO2 photonic crystal template

The conductance of polymer matrix is an important factor for the property of the polymer dispersed liquid crystal (PDLC). The nanographites are dispersed into the polymer matrix for optimising the dielectric conductive property. The synthesised nanoparticles SiO₂ was used as photonic crystal (PC) to work as a template for fabricating PDLC films. A mixture of pre-polymer and liquid crystals (LCs) was infiltrated into the void of the PC and polymerised under ultraviolet light. The void of the PC made uniform the dispersion of the liquid crystals in the films. The optical property of the PDLC films was optimised by doped nanographites and negative charge SiO₂ template. The effect of negative charge SiO₂ and nanographites on the threshold voltage and driving voltage was researched. The morphology of the PDLC films was studied by the FTIR image. The dispersed LCs droplets were uniformly affected by the addition of the nanographites. The LCs droplets dispersed in the polymer were located in the void of the SiO₂ photonic crystal.     

Effects of off-state alignment in polymer dispersed liquid crystals

Partial off-state alignment of the liquid crystal in polymer dispersed liquid crystal (PDLC) droplets was obtained by the application of electric or magnetic fields during their formation. Photopolymerization was used to induce phase separation of the liquid droplets from monomer/liquid crystal solutions. Substantial director directionality was retained in these PDLC films after removal of the fields used during their formation. This alignment affected both the off-state and the on-state electro-optic properties of the films. Transverse electrical fields (5 to 60 V across a 15 μm thickness) applied during PDLC formation from a solution of E7 (BDH Ltd) in a monomer resulted in PDLC films with progressively lower off-state scattering and lower threshold voltage. Strong longitudinal magnetic fields (9 to 14 T) applied during PDLC formation with these materials resulted in strong polarization effects in the light scattering off-state. In the infrared region, where there is less light scattering than in the visible region, the longitudinally aligned films shows tunable birefringent electro-optic effects while retaining the fast time response characteristics of PDLC films with small droplet sizes.     

Electrooptic properties of polymer dispersed liquid crystals

An investigation of the electrooptic properties of polymer dispersed liquid crystals (PDLC) is presented. These materials are light modulating systems. They show a reversible optical response from an opaque state to a highly transmitting state under the action of an appropriate electric field which aligns the liquid crystal director. The switching voltage required to establish such an electric field has been monitored as a function of (i) the starting materials used for the preparation of the PDLCs, (ii) the ageing (curing time) of the PDLC cells. Other physical properties, such as the electrical resistivity and the dielectric constant of the materials, have been measured. The correlations between these properties have been studied. The PDLC switching voltage appears to be strongly correlated with the resistivity. Our data suggest that ionic impurities play a dominant role with respect to the electrooptic response of PDLC films.     

Electrooptic properties of polymer dispersed liquid crystals

An investigation of the electrooptic properties of polymer dispersed liquid crystals (PDLC) is presented. These materials are light modulating systems. They show a reversible optical response from an opaque state to a highly transmitting state under the action of an appropriate electric field which aligns the liquid crystal director. The switching voltage required to establish such an electric field has been monitored as a function of (i) the starting materials used for the preparation of the PDLCs, (ii) the ageing (curing time) of the PDLC cells. Other physical properties, such as the electrical resistivity and the dielectric constant of the materials, have been measured. The correlations between these properties have been studied. The PDLC switching voltage appears to be strongly correlated with the resistivity. Our data suggest that ionic impurities play a dominant role with respect to the electrooptic response of PDLC films.     

Effects of off-state alignment in polymer dispersed liquid crystals

Partial off-state alignment of the liquid crystal in polymer dispersed liquid crystal (PDLC) droplets was obtained by the application of electric or magnetic fields during their formation. Photopolymerization was used to induce phase separation of the liquid droplets from monomer/liquid crystal solutions. Substantial director directionality was retained in these PDLC films after removal of the fields used during their formation. This alignment affected both the off-state and the on-state electro-optic properties of the films. Transverse electrical fields (5 to 60 V across a 15 μm thickness) applied during PDLC formation from a solution of E7 (BDH Ltd) in a monomer resulted in PDLC films with progressively lower off-state scattering and lower threshold voltage. Strong longitudinal magnetic fields (9 to 14 T) applied during PDLC formation with these materials resulted in strong polarization effects in the light scattering off-state. In the infrared region, where there is less light scattering than in the visible region, the longitudinally aligned films shows tunable birefringent electro-optic effects while retaining the fast time response characteristics of PDLC films with small droplet sizes.     

大分子引发剂分子量对接枝聚合物基体的PDLC电光性能的影响

以可逆加成-断裂链转移(RAFT)、引发转移终止(iniferter)活性自由基聚合相结合的方法,用一步法制备了不同分子量的大分子引发剂RAFT-PS-co-PCMSI(MI),并通过紫外光聚合诱导相分离法制备了以接枝聚合物为基体的聚合物分散液晶(PDLC)膜.研究了不同分子量的MI对PDLC的微观形貌,关闭状态透光率,阈值电压,饱和电压以及记忆效应等方面的影响.研究表明,降低PDLC中MI的分子量,会使得液晶微滴粒径增大,阈值电压(Vth)、饱和电压(Vsat)减小,记忆效应、关闭状态透光率升高.     

The effect of mono-sized liquid crystal domains on electro-optical properties in a polymer dispersed liquid crystal prepared by using monodisperse poly(methylmethacrylate)/liquid crystal microcapsules

Highly mono-sized poly(methyl methacrylate) (PMMA)/liquid crystal (LC) microcapsules having a mono-sized single LC domain were prepared by the solute codiffusion method and solvent evaporation. The size of the LC domain in the microcapsules could be controlled by the amount of LC introduced during the swelling stage. The electro-optical properties of the polymer dispersed liquid crystal (PDLC) prepared by using the microcapsules was highly improved. In particular, the threshold voltage was lowered and the switching behaviour with an applied electric field was sharpened drastically compared with PDLC prepared simply by solvent evaporation-induced phase separation.     

The effect of mono-sized liquid crystal domains on electro-optical properties in a polymer dispersed liquid crystal prepared by using monodisperse poly(methylmethacrylate)/liquid crystal microcapsules

Highly mono-sized poly(methyl methacrylate) (PMMA)/liquid crystal (LC) microcapsules having a mono-sized single LC domain were prepared by the solute codiffusion method and solvent evaporation. The size of the LC domain in the microcapsules could be controlled by the amount of LC introduced during the swelling stage. The electro-optical properties of the polymer dispersed liquid crystal (PDLC) prepared by using the microcapsules was highly improved. In particular, the threshold voltage was lowered and the switching behaviour with an applied electric field was sharpened drastically compared with PDLC prepared simply by solvent evaporation-induced phase separation.     

Studies on electro‐optical properties of polymer matrix/LC/ITO nanoparticles composites

In this paper, polymer‐dispersed liquid crystal (PDLC) films consisting of liquid crystal (LC)/monomers/indium tin oxide (ITO) nanoparticles with good near‐infrared absorption property had been fabricated, and the influence of the ITO nanoparticles modified with 3‐methacryloxypropyltrimethoxysilane (KH570) on the PDLC films was systematically studied. First, different liquid crystal content was studied to obtain PDLC films with good electro‐optical properties. And then, various weight ratio of ITO nanoparticles was added to samples. While the content of ITO nanoparticles was increased, the saturation voltage increased and the CR decreased. Though the electro‐optical properties of PDLC samples reduced with the addition ITO nanoparticles, the near‐infrared absorption property of films was enhanced.     

A novel polymer dispersed liquid crystal film prepared by reversible addition fragmentation chain transfer polymerization

Polymer as an important component of polymer dispersed liquid crystal (PDLC) has a great influence on electro-optical properties. In this letter, the effect of molecular weight of polymer matrix on the electro-optical properties of PDLC films was investigated with reversible addition fragmentation transfer (RAFT) polymerization. It was found that the saturation voltage and memory effect were apparently influenced by molecular weight of polymer which can be regulated efficiently by irradiation time, while the morphology of liquid crystal droplets kept unaltered. It was estimated that the increase of molecular weight of polymer enhanced entanglement between polymer and liquid crystal, which induced the different surface interaction and electro-optical properties.     

Orientational control of liquid crystal molecules via carbon nanotubes and dichroic dye in polymer dispersed liquid crystal

Polymer dispersed liquid crystals (PDLCs) using nematic liquid crystal and photo-curable polymer (NOA 65) were prepared by polymerisation-induced phase separation technique, in equal ratio (1:1) of polymer and liquid crystal (LC). We demonstrate that doping of small amount (0.125%, wt./wt.) of multiwall carbon nanotubes (CNTs) and orange azo dichroic dye in PDLC generously controlled the molecular orientation, dynamics of LC in droplet and size of droplets. The effects of multiwall CNTs and dye on PDLCs were studied in terms of transition temperature, droplet morphology, transmittance characteristic, contrast ratio and response time. The results exhibited that the values of the threshold electric fields were reduced from 8 V/µm (pure PDLC) to 1.18 and 1.72 V/µm, doped with multiwall CNTs and dye, respectively. The CNTs-doped PDLC shows faster switching response as compared with pure PDLC and dye-doped PDLC. However, dye-doped PDLC shows much higher contrast among all PDLC samples. Further, the results also illustrate that the birefringence value of LC in PDLCs was changed with doping of CNTs and dye.     

TSC study and electro‐optical properties of epoxy/acrylic polymer‐dispersed liquid‐crystal film in DICY thermal cure

We report on the structures and electro‐optical properties of epoxy/acrylic polymer‐dispersed liquid‐crystal (PDLC) films. A thermal stimulated current (TSC) analysis was used to investigate the physical structures of PDLC. In the TSC spectrum of PDLC, three relaxation peaks were observed: the glass transition of the liquid crystal, the glass transition of the polymer matrix, and the ρ transition. The ρ transition represents the discharge behavior of space charges, and its intensity increased as the curing time and content of the curing agent dicyandiamide (DICY) increased. The pre‐UV‐cured films with different DICY contents were thermally cured at 130 °C for various periods. The electro‐optical properties of PDLC, such as the contrast ratio and switching voltage, increased as the curing time of DICY, the content of DICY, or both increased. As the ambient temperature increased from 10 to 40 °C, the contrast ratio and switching voltage of PDLC gradually decreased. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 507–514, 2001     

Highly transparent memory states in polymer dispersed liquid crystal films

Electro-optical properties of polymer dispersed liquid crystal (PDLC) films which have reversed morphology are investigated. Highly transparent memory states, for which transmittances exceed more than 80 per cent, are observed in these PDLC films. The saturation voltage V₉₀ can be decreased by a PTF (a phase transition with a field) operation and becomes 10 times lower than that without PTF operation. A contrast ratio of more than 600 is obtained in the memory state of a thick PDLC film.     

The effect of the resultant microphase-separated structures of polymer matrices on the electro-optical properties of polymer dispersed liquid crystal films by Iniferter polymerization

Iniferter polymerization was employed to prepare polymer dispersed liquid crystal (PDLC) films and an additional photoinitiator was introduced to induce the phase separation of polymer matrices themselves on the process of preparing the PDLC. The effect of the polymerization kinetics and the resultant microphase-separated structures of polymer matrices on the electro-optical properties of PDLC films were studied. It was found that the bigger length scale of phase separation of polymer matrices induced strong light-scattering resulting in low ON-state transmittance. And faster polymerization kinetic induced higher threshold and saturation voltages.     

Photopolymerization kinetics and phase behaviour of acrylate based polymer dispersed liquid crystals

Polymer dispersed liquid crystal (PDLC) materials were prepared by a polymerization induced phase separation (PIPS) process using UV radiation. The samples were obtained from the liquid crystalline component E7 and a blend of monofunctional (2-ethylhexyl acrylate) and difunctional (1,6-hexane diol diacrylate) monomers as precursors of the matrix. Polymerization energetics and thermodynamic properties of PDLC materials were studied by differential scanning calorimetry. Photopolymerization kinetics and phase behaviour of the PDLC are presented and discussed as a function of UV polymerization conditions (UV light intensity, UV time exposure and isothermal curing temperature).     

Effects of hyperbranched prepolymers prepared from butyl acrylate and butyl methacrylate on the electro‐optical properties of polymer dispersed liquid crystal

Two hyperbranched prepolymers were synthesized via the reversible addition‐fragmentation chain transfer copolymerization of butyl acrylate or butyl methacrylate with divinyl benzene, respectively. These prepolymers were used in the photopolymerization‐induced phase separation process of preparing polymer dispersed liquid crystal (PDLC) films with no risk of gelation. The morphologies of PDLC samples were investigated. Of particular interest was that the driving voltage (V₉₀) of PDLC with high glass transition temperature (T_g) matrix was as low as 5 V, whereas the V₉₀ of PDLC with low T_g matrix was still high. An explanation for this phenomenon is the hypothesis that different interaction modes function at the interface of liquid crystal and polymer. Meanwhile, the hysteresis of the two systems was minor, which correlated with the hyperbranched structure of polymer. The on‐state transmittance (T_ON) of PDLC films enhanced because of the well matching between the refractive index of polymer and that of liquid crystal. Copyright © 2011 John Wiley & Sons, Ltd.     

High on-state clarity polymer dispersed liquid crystal films

Abstract

Results are presented which show that the on-state clarity of a UV cured polymer dispersed liquid crystal (PDLC) film depends on the refractive index of the final polymer in the PDLC film, the ordinary refractive index of the liquid crystal, the solubility of the liquid crystal in the prepolymer and the rate at which the film is cured. Liquid crystal mixtures for use in PDLC films are chosen such that the ordinary refractive index of the liquid crystal is equal to the refractive index of the polymer matrix. It has been shown previously that a large quantity of liquid crystal remains dissolved in the polymer matrix, thus increasing the mismatch between the refractive index of the polymer and the ordinary refractive index of the liquid crystal and therefore reducing the on-state clarity. For liquid crystal mixtures which have high solubility in the prepolymer (>60 per cent) the mismatch in the refractive indices can be very large and the on-state clarity of the resulting film can be very poor (T _on<70 per cent). Results are presented which show that it is possible to increase the on-state clarity of such films by increasing the rate at which these films cure. If the liquid crystal is less soluble in the prepolymer (<45 per cent), a PDLC film formed from such a liquid crystal/ prepolymer system often has very good on-state clarity (T _on>75 per cent) be it cured slowly or quickly. Results are also presented which show that in order to achieve a true measure of on-state clarity it is necessary to use a small collection angle (<3°) in the detecting optics. If larger collection angles are used, the photodetector collects light which is scattered out of the specular beam, thus leading to a false measure of on-state clarity.