In-Vitro Degradation Behaviors of Composite Scaffolds Based on 1,4-Butadnediamine Modified Poly(lactide-co-glycolide) and Nanobioceramics

In-vitro degradation behaviors of composite scaffold materials composed of 1,4-butanediamine modified poly(lactide-co-glycolide) (BMPLGA), nanobioactive glass (NBG) and β-tricalcium phosphate (β-TCP) were systematically investigated in phosphate-buffered solution (PBS) at 37?°C. The properties of the BMPLGA/NBG-β-TCP and BMPLGA scaffolds, including the changes of pH value, mass, water uptake, compressive strength and molecular mass, were investigated as a function of degradation time. The results showed that the introduction of the NBG and β-TCP particles played important roles in the degradation of BMPLGA matrix. The degradation rate of the BMPLGA/NBG-β-TCP scaffolds was slower than that of the BMPLGA scaffolds.     

Preparation and In Vitro Degradation Behavior of Poly(L-lactide-co-glycolide) by Direct-Melt Polycondensation

Poly(L-lactide-co-glycolide)(PLGA)copolymer (85/15) was prepared by direct-melt polycondensation instead of a ring-opening process. The polymer samples were hydrolyzed at 37°C in phosphate-buffered saline (PBS) for periods up to 10 weeks and the degradation behavior was characterized through weight average molecular mass change, mass loss, water uptake, and morphology. The results indicate that mass loss, weight average molecular mass, and water uptake of PLGA increase with increasing time; however, pH value of the PBS solution decreases. The degradation is heterogeneous—degradation in their central parts was faster than in the surface and regions due to the increased concentration of the acidic degradation products inside.     

Thermal and Thermo-Oxidative Degradation of Biodegradable Poly(Ester Urethane) Containing Poly(L-Lactic Acid) and Poly(Butylene Succinate) Blocks

A novel biodegradable poly(ester urethane; PEU) was synthesized by chain extension reaction of dihydroxylated poly(L-lactic acid; PLLA) and poly(butylene succinate; PBS) using diisocyanate as a chain extender. The kinetics of thermal and thermo-oxidative degradation of PEU containing PLLA and PBS blocks were studied by thermogravimetric analysis (TGA). TGA results indicated that PEU was more stable in air than in nitrogen and went through a two-stage degradation process irrespective of the experimental atmosphere. Activation energy of each stage was calculated by means of Kissinger, Kim-Park, Friedman, Flynn-Wall-Ozawa, and Kissinger-Akahira-Sunose methods. For the first stage, the activation energy value obtained in air was slightly higher than the corresponding value obtained in nitrogen; and for the second stage, the activation energy showed a much higher value in air than in nitrogen. The Coats-Redfern method was employed to study the degradation mechanism of each stage. The results indicated that the degradation of the first stage follows the P3/4 mechanism irrespective of the experimental atmosphere; the degradation of the second stage of PEU obeys the P1 mechanism in nitrogen while P3/2 in air.     

In vitro studies of PEG thin films with different molecular weights deposited by MAPLE

In this work, polyethylene glycol (PEG) films were produced by Matrix Assisted Pulsed Laser Evaporation (MAPLE). The possibility to tailor the properties of the films by means of polymer molecular weight was explored. The films of PEG of average molecular weights 400 Da, 1450 Da, and 10000 Da (PEG₄₀₀, PEG₁₄₅₀, and PEG₁₀₀₀₀) were investigated in vitro, in media similar with those inside the body (phosphate buffer saline PBS with pH 7.4 and blood). The mass of the polymer did not change during this treatment, but the polymer molecular weight was found to strongly influence the films properties and their behavior in vitro. Thus, immersion in PBS induced swelling of the PEG films, which was more pronounced for PEG polymers of higher molecular weight. Prior to immersion in PBS, the PEG films of higher molecular weight were more hydrophilic, the water contact angles decreasing from ～66 grd for PEG₄₀₀ to ～41 grd for PEG₁₄₅₀ and to ～15 grd for PEG₁₀₀₀₀. The same trend was observed during immersion of the PEG films in PBS. Before immersion in PBS, the refractive index of the films increased from ～1.43 for PEG₄₀₀ to ～1.48 for PEG₁₄₅₀ and to ～1.68 for PEG₁₀₀₀₀. During immersion in PBS the refractive index decreased gradually, but remained higher for the PEG molecules of higher mass. Finally, blood compatibility tests showed that the PEG films of higher molecular weight were most compatible with blood.     

Preparation and Characterization of Composites Based on Poly (Butylene Succinate) and Poly (Lactic Acid) Grafted Tetracalcium Phosphate

Tetracalcium phosphate (TTCP, Ca₄(PO₄)₂O) was functionalized by poly (l-lactic acid) (PLLA) in order to improve the dispersion of TTCP particles in poly (butylene succinate) (PBS) matrices, and then a series of the PLLA grafted TTCP/PBS (g-TTCP/PBS) composites were prepared via melt processing. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), tensile analysis, differential scanning calorimetry (DSC), thermogravimetric analysis (DTG/TGA) and melt rheological analysis were used to investigate the structure and properties of the g-TTCP/PBS composites. The results revealed that l-lactide could be grafted onto the surface of TTCP, and the g-TTCP/PBS composites showed the best mechanical properties when the content of g-TTCP was 10 wt%. The crystallization temperature of g-TTCP/PBS composites tended to increase with the increase of g-TTCP contents. The functionalized particles played an important role in augmenting the thermal degradation rate and the complex viscosity of the composites due to their unique structure and the reasonable interfacial interaction between the particles and PBS matrix.     

Characterization of Chitosan-Gelatin Blend Scaffolds

Vacuum freeze-drying was used to prepare chitosan-gelatin (CG) scaffolds from hydrogels, with glutaraldehyde (GA) used as a crosslinker. The effects of the changes in volume ratios of the 2?wt% CG and GA solutions on scaffold performance were studied. The ratio of chitosan to gelatin solution volumes, vr(C/G), was adjusted to 1/2 or 1/1, with the 0.25?wt% GA volume at 3, 6, or 8% of the CG/GA volume. Six groups of CG scaffolds were fabricated and the scaffolds performance compared. After the cells were incubated for 4?days, hematoxylin eosin (HE) staining was used to observe the spreading of human skin keratinocyte (HaCaT) cells on these scaffolds, with the MTT method also used to detect the cells proliferation. The inhibition zone method was used on cells cultures to determine the antibacterial properties of the scaffolds against S. aureus and E. coli. Scaffolds were also examined for degradation in lysozyme and their compression properties were tested after degradation. The results showed that the HaCaT cells grew well on these scaffolds and proliferated significantly, indicating that these scaffolds possessed good cytocompatibility. With increased chitosan volume, the antibacterial properties of the scaffolds against S. aureus increased, however, there was no significant change in the antibacterial properties toward E. coli. Increased volumes of chitosan and GA decreased the scaffolds degradation rates and improved the elastic compressive moduli of the scaffolds after degradation. The scaffolds in the vr(C/G) = 1/1, 8% GA group have potential application prospects in the field of skin regeneration.     

Water electrolysis-induced optical degradation of aluminum-doped zinc oxide films

A type of optical degradation of aluminium-doped zinc oxide (AZO) films due to water electrolysis-induced reduction reaction was reported. An experiment was designed in which AZO films were immersed in a 0.01 M NaOH aqueous solution as cathode to electrolyze water. Significant decreases in the optical transmission of the treated samples were observed. Studies by X-ray diffraction and scanning electron microscope showed that the degradation of AZO films was due to compositional and structural changes with the treatment of water electrolysis, which resulted from the reduction reaction of atomic hydrogen generated in the electrolysis of water. This optical degradation reflects the stability degradation of AZO films under water electrolysis environment.     

Preparation and Characterization of Gelatin–Poly(L-lactic) Acid/Poly(hydroxybutyrate-co-hydroxyvalerate) Composite Nanofibrous Scaffolds

Poly(L-lactic) acid (PLLA) scaffolds, prepared by electrospinning technology, have been suggested for use in tissue engineering. They remain a challenge for application in biological fields due to PLLA's slow degradation and hydrophobic nature. We describe PLLA, PLLA/poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV), and PLLA/PHBV/gelatin (Gt) composite nanofiberous scaffolds (Gt–PLLA/PHBV) electrospun by changing the electrospinning technology. The morphologies and hydrophilicity of these fibers were characterized by scanning electron microscopy (SEM) and water contact angle measurement. The results showed that the addition of PHBV and Gt resulted in a decrease in the diameters and their distribution and greatly improved the hydrophilicity. The in-vitro degradation test indicated that GT–PLLA/PHBV composite scaffolds exhibited a faster degradation rate than PLLA and PLLA/PHBV scaffolds. Dermal fibroblasts viabilities on nanofibrous scaffolds were characterized by [3-(4, 5-dimethylthiazol-2-yl)-2, 5-diphenyltetrazolium bromide] (MTT) assay and cell morphologies after 7 days culture. Results indicated that the GT–PLLA/PHBV composite nanofibers showed the highest bioactivity among the three scaffolds and increased with increasing time. The SEM images of cells/scaffolds composite materials showed the GT–PLLA/PHBV composite nanofibers enhanced the dermal fibroblasts's adhesion, proliferation, and spreading. It is suggested that the nanofibrous composite scaffolds of GT–PLLA/PHBV composites would be a promising candidate for tissue engineering scaffolds.     

Preparation and Degradation Behaviors of Poly(L-lactide-co-glycolide-co-ε-caprolactone)/1,4-butanediamine Modified Poly(lactic-co-glycolic acid) Blend Film

Abstract

Polymer blending is an attractive method for producing new polymer materials with excellent properties. In this work the blended polymers were prepared from poly(L-lactide-co-glycolide-co-ε-caprolactone) and 1,4-butanediamine modified poly(lactic-co-glycolic acid) (PLLGC/BMPLGA). The hydrophilicity was studied by static water contact angle tests. The in-vitro degradation behaviors of the PLLGC/BMPLGA blended films were investigated during various degradation periods. The results showed that the introduction of the PLLGC reduced the hydrophilicity and degradation rate of the blended polymers while improved the tensile strength and elongation percentage. Therefore, we suggest the blends of the PLLGC and BMPLGA could supply a potential biomaterial for application in the medical field for use as tissue engineering scaffolds or drug delivery.     

Diffusion of dimethyl sulfoxide in tissue engineered collagen scaffolds visualized by computer tomography

Cryopreservation is a convenient method for long-term preservation of natural and engineered tissues in regenerative medicine. Homogeneous loading of tissues with CPAs, however, forms one of the major hurdles in tissue cryopreservation. In this study, computer tomography (CT) as a non-invasive imaging method was used to determine the effective diffusion of Me2SO in tissue-engineered collagen scaffolds. The dimensions of the scaffolds were 30 x 30 x 10 mm3 with a homogeneous pore size of 100 microm and a porosity of 98%. CT images were acquired after equilibrating the scaffolds in phosphate buffered saline (PBS) and transferring them directly in 10% (v/v)Me2SO. The Me2SO loading process of the scaffold could thus be measured and visualized in real time. The experimental data were fitted using a diffusion equation. The calculated effective diffusion constant for Me2SO in the PBS loaded scaffold was determined from experimental diffusion studies to be 2.4 x 10(-6) cm2/s at 20 degrees C.     

Influence of Bovine Bone Content on In Vitro Degradation of Poly-L-lactic Acid and Bovine Bone Composite Materials

In vitro degradation experiments of poly-L-lactic acid (PLLA) and bovine bone (BB) composites were carried out in a phosphate-buffered solution (PBS) at 37°C with a pH of 7.4. The influence of BB content on pH value of PBS, water uptake, molecular weights, molecular weight distributions, weight losses, mechanical strengths, and morphologies of PLLA/BB was investigated with degradation times. The results indicated that the presence of the BB modified the degradation of the PLLA matrix. The degradation rate of PLLA in the PLLA/BB composite was slower than the degradation rate of the sole PLLA material. Furthermore, the degradation rate of the composites became slower with the increasing content of BB in PLLA/BB composites.     

PL and CL degradation and characteristics of SrAl2O4: Eu,Dy phosphors

Strontium aluminate phosphors are ideal for luminescent infrastructure materials. Their brightness and persistent glow time are much higher than previously used sulphide phosphors. Strontium aluminates prepared by the sol–gel and combustion methods are compared with commercially available strontium aluminate. High luminescent efficient SrAl₂O₄:Eu²⁺,Dy³⁺ pulsed laser deposited (PLD) thin films were also produced using the commercially available powder. Photoluminescence (PL) degradation studies showed that the phosphor intensity decreased about 20% over a period of 2 weeks under ultraviolet (UV) irradiation. Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) showed that cathodoluminescence (CL) degradation is due to the formation of SrO due to electron stimulated surface reactions. The light output mechanism of the phosphor is also discussed in more detail.     

Fabrication of Poly(D,L-lactide-co-glycolide) Microspheres and Degradation Characteristics in vitro

Poly(D,L-lactide-co-glycolide) (PLGA, 75/25) microspheres were prepared by the emulsion solvent extraction/evaporation technique and their degradation behaviors in vitro at 37°C were investigated. PLGA microspheres with a smooth and nonporous surface were obtained, with a mean particle size of 114.15 μm. It was observed that mass loss and water uptake of PLGA increased with increasing degradation time; however, weight average molecular weight and the pH value of the phosphate buffered saline (PBS) solution decreased. The observed relative rates of mass loss vs. molecular weight decreases were consistent with the explanation that PLGA underwent bulk degradation rather than surface degradation. During the degradation time, the surface of the PLGA microspheres became coarse and there were many micropores that developed upon immersion in the PBS. The microspheres lost their spherical form with increasing degradation time.     

Biocompatible polymeric implants for controlled drug delivery produced by MAPLE

Implants consisting of drug cores coated with polymeric films were developed for delivering drugs in a controlled manner. The polymeric films were produced using matrix assisted pulsed laser evaporation (MAPLE) and consist of poly(lactide-co-glycolide) (PLGA), used individually as well as blended with polyethylene glycol (PEG). Indomethacin (INC) was used as model drug. The implants were tested in vitro (i.e. in conditions similar with those encountered inside the body), for predicting their behavior after implantation at the site of action. To this end, they were immersed in physiological media (i.e. phosphate buffered saline PBS pH 7.4 and blood). At various intervals of PBS immersion (and respectively in blood), the polymeric films coating the drug cores were studied in terms of morphology, chemistry, wettability and blood compatibility. PEG:PLGA film exhibited superior properties as compared to PLGA film, the corresponding implant being thus more suitable for internal use in the human body. In addition, the implant containing PEG:PLGA film provided an efficient and sustained release of the drug. The kinetics of the drug release was consistent with a diffusion mediated mechanism (as revealed by fitting the data with Higuchi's model); the drug was gradually released through the pores formed during PBS immersion. In contrast, the implant containing PLGA film showed poor drug delivery rates and mechanical failure. In this case, fitting the data with Hixson-Crowell model indicated a release mechanism dominated by polymer erosion.     

Transport and stability studies on high band gap a-Si:H films prepared by argon dilution

Device quality hydrogenated amorphous silicon films (a-Si:H) are deposited at a high deposition rate (4–5 Å/s) using a mixture of argon and hydrogen-diluted silane. The films exhibit good opto-electronic properties and show less degradation upon light soaking. Light-induced changes in conductivity could be annealed at much lower temperature. The presence of Ar^* and atomic hydrogen in plasma replaces the weak Si-Si bonds, which are responsible for light-induced degradation by strong Si-Si bonds. This results in the improved stability of the films.     

Solid-phase photocatalytic degradation of polystyrene plastic with goethite modified by boron under UV-vis light irradiation

A novel photodegradable polyethylene-boron-goethite (PE-B-goethite) composite film was prepared by embedding the boron-doped goethite into the commercial polyethylene. The goethite catalyst was modified by boron in order to improve its photocatalytic efficiency under the ultraviolet and visible light irradiation. Solid-phase photocatalytic degradation of the PE-B-goethite composite film was carried out in an ambient air at room temperature under ultraviolet and visible light irradiation. The properties of composite films were compared with those of the pure PE films and the PE-goethite composite films through performing weight loss monitoring, scanning electron microscope (SEM) analysis, FT-IR spectroscopy and X-ray photoelectron spectroscopy (XPS). The photo-induced degradation of PE-B-goethite composite films was higher than that of the pure PE films and the PE-goethite composite films under the UV-irradiation, while there has been little change under the visible light irradiation. The weight loss of the PE-B-goethite (0.4 wt.%) composite film reached 12.6% under the UV-irradiation for 300 h. The photocatalytic degradation mechanism of the composite films was briefly discussed.     

Effects of substrate temperature and Zn addition on the properties of Al-doped ZnO films prepared by magnetron sputtering

Al-doped ZnO (AZO) films prepared at different substrate temperature and AZO films with intentional Zn addition (ZAZO) during deposition at elevated substrate temperature were fabricated by radio frequency magnetron sputtering on glass substrate, and the resulting structural, electrical, optical properties together with the etching characteristics and annealing behavior were comparatively examined. AZO films deposited at 150 °C showed the optimum electrical properties and the largest grain size. XPS analysis revealed that AZO films deposited at elevated temperature of 450 °C contained large amount of Al content due to Zn deficiency, and that intentional Zn addition during deposition could compensate the deficiency of Zn to some extent. It was shown that the electrical, optical and structural properties of ZAZO films were almost comparable to those of AZO film deposited at 150 °C, and that ZAZO films had much smaller etching rate together with better stability in severe annealing conditions than AZO films due possibly to formation of dense structure.     

In-vitro degradation behavior and biological properties of a novel maleated poly (D,L-lactide-co-glycolide) for biomedical applications

Synthesized biodegradable polymers with controlled degradability and good biological safety would be useful in biomedical applications. In this work a novel maleated poly(D,L-lactide-co-glycolide) (MPLGA) was melt copolymerized from maleic anhydride, D,L-lactide and glycolide monomers. The degradation behavior in phosphate-buffered solution (PBS) was investigated and the biological properties were studied by using fibroblastic cells cultured in an extract of MPLGA and by an in-vitro cell cytotoxicity test. The results indicated that the MPLGA was successfully obtained using the melt-copolymerization method. The maleic anhydride groups in the MPLGA led to a faster degradation in PBS than PLGA. Fibroblastic cells showed normal morphologies in MPLGA extracts, and the MPLGA materials showed no cell cytotoxicity. The in-vitro biological properties indicated that the obtained MPLGA had good biocompatibility and would be useful for medical applications.     

Effects of Mn doping on BaTiO3 thin films grown on highly oriented pyrolytic graphite substrates

We report multiferroelectric properties of Mn-doped BaTiO₃ (MBTO) thin films on highly oriented pyrolytic graphite (HOPG) substrates. The MBTO thin films were grown on the HOPG substrate by pulse laser deposition. For comparison purpose, undoped BaTiO₃ (BTO) thin films were also prepared under same experimental conditions. The BTO and MBTO thin films were polycrystalline, indicating that the MBTO thin film has better crystallinity than the BTO thin film. The leakage current of the MBTO thin film was reduced due to the Mn doping substitution. In addition, the MBTO thin film exhibited better than the BTO thin film in ferroelectric and magnetic behaviors. We suggest that the Mn doping bring about the improvements of ferroelectric and ferromagnetic properties of the BTO thin films. Based on atomic force microscopy (AFM) and conducting AFM (CAFM) studies, the grain size of MBTO thin film was much larger than that of BTO thin film.     

Mechanically induced changes in amylose structure and effect on thermal behavior in the presence of TiO2 nanoparticles

Thermal behavior of amylose/TiO₂ films under ultrasonic irradiation was investigated, and the final product of each process was applied to prepare amylose/TiO₂ nanocomposite films. The effects of different degradation techniques on thermal behavior, crystallinity, and molecular weight distribution of amylose were surveyed. The evaluations of structural changes and thermal behaviors were performed by X-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermogravimetry analysis, FT-IR spectroscopy, and scanning electron microscopy. The XRD results clarified that the crystalline shape of amylose molecules formed is an A-type crystal due to the sonophotocatalytic processing, while the FT-IR spectra does not approve any chemical change in amylose structure. The DSC data submitted a broad endothermic peak for amylose. In the case of high loading of nanoparticles, the endothermic analysis results and diffraction peaks for the sonophotocatalytic process were not significant. This indicates that the length of amylose chains through the sonophotocatalytic degradation became smaller. An increase at the loading of TiO₂ improved the hydrophilic properties of amylose/TiO₂ films, which leads to the modification of water absorption behavior. Mechanical properties of amylose/TiO₂ films were affected by the uniform dispersion of TiO₂ in the polymer matrix.