Synthesis and characterization of partially disulfonated hydroquinone‐based poly(arylene ether sulfone)s random copolymers for application as proton exchange membranes

Partially disulfonated hydroquinone (HQ)‐based poly(arylene ether sulfone) random copolymers were synthesized and characterized for application as proton exchange membranes. The copolymer composition was varied in the degree of disulfonation. The copolymers were characterized by ¹H NMR, Differential Scanning Calorimetry (DSC), and other analytical techniques. The copolymer with a 25% degree of disulfonation showed the best balance between water uptake and proton conductivity. The copolymers showed substantially reduced methanol permeability compared with Nafion® and satisfactory direct methanol fuel cell performance. The methanol selectivity improved significantly in comparison to Nafion® 117. At a given ionic composition, the HQ‐based system showed higher water uptake and proton conductivity than the biphenol‐based (BPSH‐xx) poly(arylene ether sulfone)s copolymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 384–391, 2009     

Synthesis of novel phosphinic acid-containing polymers

Three arylene difluoride monomers containing phosphine oxide ( 1 ), phosphinic acid ( 2 ), or phosphinate ester ( 3 ) groups were prepared and polymerized with bisphenol A to give novel poly-(arylene ether)s ( 4 , 5 , and 6 ). The polymers obtained had moderate molecular weights (η_inh: 0.14–0.30 dL g⁻¹ in N-methylpyrrolidinone) and glass-transition temperatures (T_g: 102–200 °C), depending on the phosphine group in the main chain. Using bis(4-fluorophenyl)sulfone as a comonomer improved the polymerization to give copolymers with higher solution viscosities. The stoichiometric investigation revealed that 7 mol % excess of fluoride monomer gave the highest molecular weight copolymer 8 with η_inh of 0.78 dL g⁻¹, which had a T_g of 176 °C, a T of 432 °C, and formed a hard film by casting from solution. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1854–1859, 2001     

Selectively sulfonated poly(aryl ether sulfone)‐b‐polybutadiene for proton exchange membrane

A series of selectively sulfonated poly(arylene ether sulfone)‐b‐polybutadiene copolymers (SPAES‐b‐PB) were prepared based on carboxyl terminated polybutadiene (CTPB) and sulfonated poly(arylene ether sulfone) (SPAES) that was directly prepared by polycondensation of 4,4′‐isopropylidenediphenol with different molar ratios of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenyl sulfone (SDCDPS) to 4,4′‐dichlorodiphenylsulfone (DCDPS), and subsequent selective postsulfonation of flexible PB block was carried out. Epoxidized modification of membranes was conducted by an in situ‐generated peracid method. The content of sulfonic acid groups attaching to aromatic rings in SPAES was determined by ¹H NMR and was in good aggrement with the controlled ratios. The effect of sulfonated rigid blocks on the postsulfonation of PB blocks was studied by Fourier transform infrared spectroscopy. The glass transition temperature (T_g) and the temperature of the melting peak (T) of membranes in acid form were studied by differential scanning calorimetry. Fenton's reagent test revealed that the selectively sulfonated SPAES‐b‐PB membranes had good stability to oxidation. The microstructure of rod‐like rigid SPAES blocks and interpenetrating network of ions were observed by transmission electron microscopy. Complex impedance measurement showed that an epoxidized membrane with SPAES‐40 exhibited the highest proton conductivity (1.08 × 10^?1 S/cm, 90 °C), which was due to the formation of obvious ionic networks. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 665–672, 2006     

Graft‐crosslinked Copolymers Based on Poly(arylene ether ketone)‐gc‐sulfonated Poly(arylene ether sulfone) for PEMFC Applications

Novel poly(arylene ether ketone) polymers with fluorophenyl pendants and phenoxide‐terminated wholly sulfonated poly(arylene ether sulfone) oligomers are prepared via Ni(0)‐catalyzed and nucleophilic polymerization, respectively, and subsequently used as starting materials to obtain graft‐crosslinked membranes as polymer electrolyte membranes. The phenoxide‐terminated sulfonated moieties are introduced as hydrophilic parts as well as crosslinking units. The chemical structure and morphology of the obtained membranes are confirmed by ¹H NMR and tapping‐mode AFM. The properties required for fuel cell applications, including water uptake and dimensional change, as well as proton conductivity, are investigated. AFM results show a clear nanoscale phase‐separation microstructure of the obtained membranes. The membranes show good dimensional stability and reasonably high proton conductivities under 30–90% relative humidity. The anisotropic proton conductivity ratios (σ_⟂/||) of the membranes in water are in the range 0.65–0.92, and increase with an increase in hydrophilic block length. The results indicate that the graft‐crosslinked membranes are promising candidates for applications as polymer electrolyte membranes.

     

Copoly(arylene ether nitrile) and copoly(arylene ether sulfone) ionomers with pendant sulfobenzoyl groups for proton conducting fuel cell membranes

Three series of fully aromatic ionomers with naphthalene moieties and pendant sulfobenzoyl side chains were prepared via K₂CO₃ mediated nucleophilic aromatic substitution reactions. The first series consisted of poly(arylene ether)s prepared by polycondensations of 2,6‐difluoro‐2′‐sulfobenzophenone (DFSBP) and 2,6‐dihydroxynaphthalene or 2,7‐dihydroxynaphthalene (2,7‐DHN). In the second series, copoly(arylene ether nitrile)s with different ion‐exchange capacities (IECs) were prepared by polycondensations of DFSBP, 2,6‐difluorobenzonitrile (DFBN), and 2,7‐DHN. In the third series, bis(4‐fluorophenyl)sulfone was used instead of DFBN to prepare copoly(arylene ether sulfone)s. Thus, all the ionomers had sulfonic acid units placed in stable positions close to the electron withdrawing ketone link of the side chains. Mechanically strong proton‐exchange membranes with IECs between 1.1 and 2.3 meq g⁻¹ were cast from dimethylsulfoxide solutions. High thermal stability was indicted by high degradation temperatures between 266 and 287 °C (1 °C min⁻¹ under air) and high glass transition temperatures between 245 and 306 °C, depending on the IEC. The copolymer membranes reached proton conductivities of 0.3 S cm⁻¹ under fully humidified conditions. At IECs above ∼1.6 meq g⁻¹, the copolymer membranes reached higher proton conductivities than Nafion^® in the range between −20 and 120 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis,structure, and properties of poly[1‐(trimethylgermyl)‐1‐propyne]

Polymerization of 1‐(trimethylgermyl)‐1‐propyne (TMGP) with TaCl₅ and NbCl₅ produced a colorless polymer in high yields, whose molecular weight reached about 3 × 10⁵–14 × 10⁵. The molecular weight distribution of the poly(TMGP) with NbCl₅ in cyclohexane was somewhat narrow (M_w /M_n = ∼1.54). The TaCl₅‐based poly(TMGP) dissolved in toluene, chloroform, cyclohexane, carbon disulfide, carbon tetrachloride, tetrahydrofuran, hexane, and so forth; the NbCl₅‐based polymer was less soluble and did not dissolve in hexane, despite its lower molecular weight. The cis contents of the NbCl₅‐ and TaCl₅‐based poly(TMGP)s determined by ¹³C NMR were 67 ± 5 and 28 ± 3%, respectively. The onset temperature of the weight loss of poly(TMGP) in air was 350 °C, indicating fair thermal stability. The oxygen permeability coefficient (P) of poly(TMGP) at 25 °C was 7800 barrer after the methanol conditioning, and the permeability was fairly stable to aging. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2964–2969, 2000     

Phosphonyl/hydroxyl hydrogen bonding–induced miscibility of poly(arylene ether phosphine oxide/sulfone) statistical copolymers with poly(hydroxy ether) (phenoxy resin): Synthesis and characterization

High molecular weight bisphenol A or hydroquinone‐based poly(arylene ether phosphine oxide/sulfone) homopolymer or statistical copolymers were synthesized and characterized by thermal analysis, gel permeation chromatography, and intrinsic viscosity. Miscibility studies of blends of these copolymers with a (bisphenol A)‐epichlorohydrin based poly(hydroxy ether), termed phenoxy resin, were conducted by infrared spectroscopy, dynamic mechanical analysis, and differential scanning calorimetry. All of the data are consistent with strong hydrogen bonding between the phosphonyl groups of the copolymers and the pendent hydroxyl groups of the phenoxy resin as the miscibility‐inducing mechanism. Complete miscibility at all blend compositions was achieved with as little as 20 mol % of phosphine oxide units in the bisphenol A poly(arylene ether phosphine oxide/sulfone) copolymer. Single glass transition temperatures (T_g) from about 100 to 200°C were achieved. Replacement of bisphenol A by hydroquinone in the copolymer synthesis did not significantly affect blend miscibilities. Examination of the data within the framework of four existing blend T_g composition equations revealed T_g elevation attributable to phosphonyl/hydroxyl hydrogen bonding interactions. Because of the structural similarities of phenoxy, epoxy, and vinylester resins, the new poly(arylene ether phosphine oxide/sulfone) copolymers should find many applications as impact‐improving and interphase materials in thermoplastics and thermoset composite blend compositions. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1849–1862, 1999     

Synthesis and characterization of multiblock partially fluorinated hydrophobic poly(arylene ether sulfone)‐hydrophilic disulfonated poly(arylene ether sulfone) copolymers for proton exchange membranes

Hydrophobic‐hydrophilic sequence multiblock copolymers, based on alternating segments of phenoxide terminated fully disulfonated poly(arylene ether sulfone) (BPS100) and fluorine‐terminated poly(arylene ether sulfone) (6FBPS0) were synthesized and evaluated for application as proton exchange membranes. By utilizing mild reaction conditions the ether–ether interchange reactions were minimized, preventing the randomization of the multiblock copolymers. Tough, ductile, transparent membranes were solution cast from the block copolymers and were characterized with regard to intrinsic viscosity, morphology, water uptake, and proton conductivity. The conductivity values of the 6FBPS0‐BPSH100 membranes were compared to Nafion 212 and a partially fluorinated sulfonated poly(arylene ether sulfone) random copolymer (6F40BP60). The nanophase separated morphology was confirmed by transmission electron microscopy and small angle X‐ray scattering, and enhanced proton conductivity at reduced relative humidity was observed with longer block lengths. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and characterization of poly(arylene ether sulfone) copolymers with sulfonimide side groups for a proton‐exchange membrane

A sulfonimide‐containing comonomer derived from 4,4′‐dichlorodiphenylsulfone was synthesized and copolymerized with 4,4′‐dichlorodiphenylsulfone and 4,4′‐biphenol to prepare sulfonimide‐containing poly(arylene ether sulfone) random copolymers (BPSIs). These copolymers showed slightly higher water uptake than disulfonated poly(arylene ether sulfone) copolymer (BPSH) controls, but their proton‐conductivity values were very comparable to those of the BPSH series with similar ion contents. The proton conductivity increased with the temperature for both systems. For samples with 30 mol % ionic groups, BPSI showed less temperature dependence in proton conductivity and slightly higher methanol permeability in comparison with BPSH. The thermal characterization of the sulfonimide copolymers showed that both the acid and salt forms were stable up to 250 °C under a nitrogen atmosphere. The results suggested that the presumed enhanced stability of the sulfonimide systems did not translate into higher protonic conductivity in liquid water. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6007–6014, 2006     

Cross‐linked poly(aryl ether sulfone) membranes for direct methanol fuel cell applications

Partially sulfonated poly(aryl ether sulfone) (PESS) was synthesized and methacrylated via reaction with glycidyl methacrylate (PESSGMA) and cross‐linked via radical polymerization with styrene and vinyl‐phosphonic acid (VPA). The chemical structures of the synthesized pre‐polymers were characterized via FTIR and ¹H NMR spectroscopic methods and molecular weight was determined via GPC. Membranes of these polymers were prepared via solution casting method. The crosslinking of the PESS polymer reduced IEC, proton conductivity, swelling in water, and methanol permeability of the membranes while increasing the modulus and the glass transition temperature. However, the introduction of the VPA comonomer increased the proton conductivity while maintaining excellent resistance to methanol cross‐over, which was significantly higher as compared with both PESS and the commercial Nafion membranes. Membranes of PESSGMA copolymers incorporating VPA, exhibited proton conductivity values at 60 °C in the range of 16–32 mS cm⁻¹ and methanol permeability values in the range of 6.52 × 10⁻⁹ – 1.92 × 10⁻⁸ cm² s⁻¹. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 558–575     

Synthesis and properties of hyperbranched poly(ether sulfone)s prepared by self‐polycondensation of novel AB2 monomer

Hyperbranched poly(ether sulfone)s were prepared by the self‐polycondensation of the novel AB₂ monomer, 4‐(3,5‐hydroxyphenoxy)‐4′‐fluorodiphenylsulfone. The high‐molecular‐weight polymers were isolated in good yields. The degree of branching (DB) of the resulting polymers was investigated by the preparation of dendritic and linear model compounds. The DB determined by gated decoupling ¹³C NMR measurements was in the range 0.17–0.41 and was dependent on the base used for the self‐polycondensation. It was found that cesium fluoride was an effective base to form the polymer having the DB of 0.41. The resulting hyperbranched poly(ether sulfone)s showed good solubility in organic solvents. The solubility and the glass transition temperature of the polymers were influenced by the terminal functional groups. The unique thermal crosslinking phenomenon was observed during the DSC measurements of the hydroxyl‐terminated hyperbranched poly(ether sulfone) under air condition. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Nanometer‐scale surface modification by polymerization of tetrafluoroethylene on polymer substrates in supercritical fluoroform

Surface penetrated polymerization of tetrafluoroethylene (TFE) was carried out on a polycarbonate (PC) plate in supercritical fluoroform (scCHF₃). Since the high diffusiveness is one of peculiar features of supercritical fluids, TFE monomers and initiators (perfluorinated benzoyl peroxide) could penetrate into the surface of polymer substrates and be photo‐polymerized. After washing physisorbed homopolymers on the surface, polytetrafluoroethylene (PTFE) was found to penetrate into 50–800 nm depth from the surface and covered the PC surface in the proportion of 85%. The surface coverage density and the penetration depth could be controlled by adjusting of the pressure of scCHF₃. The TFE‐penetrated polymerization could be applied for various polymer plates such as polyethylene, polystyrene, polypropylene, poly(ethylene terephthalate), and polyimide. In addition to polymer plates, this technique could be applied to a cellulose paper, a nylon textile, and a porous PC membrane. The PTFE‐penetrated nylon textile showed a high resistance for washing test with detergents, compared with the commercial fluoropolymer‐sprayed nylon textile. The PTFE‐penetrated porous PC membrane showed high oxygen permeability (P/P = 5.2), compared with that of the untreated PC membrane (P/P = 3.5) in gas permeation experiments of O₂ and N₂. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1577–1585, 2008     

Synthesis and Properties of Novel Side‐Chain Sulfonated Poly(Arylene Ether Sulfone)s for Proton Exchange Membranes

A series of novel side‐chain sulfonated poly(arylene ether sulfone) (SPAES) multiblock and random copolymers were synthesized by condensation polymerization from a new disulfonated aryl sulfone monomer, 4,4′‐difluoro‐2,2′‐bis(3‐sulfobenzoyl)diphenyl sulfone disodium salt (DFBSPS). The chemical structures of DFBSPS and the SPAESs were characterized by proton nuclear magnetic resonance (¹H NMR) and Fourier transform infrared (FTIR) spectra. The SPAES membranes prepared by solution cast method exhibited high tensile strength (50–71 MPa) and high radical oxidative stability. They could keep their morphology and maintain proton conductivities after hydrolysis test in 95 °C water for 1000 h. They also showed smaller swelling ratio in in‐plane direction than in through‐plane direction and such an anisotropic effect was more significant for the multiblock copolymers than for the random ones. The multiblock copolymer membranes exhibited higher proton conductivity than the random ones with similar ion exchange capacities (IECs). Preliminary hydrogen‐oxygen fuel cell tests were performed at 60 °C and 80% relative humidity (RH). The results showed that the single cell equipped with the multibiock copolymer membrane SB3 exhibited 0.12 W cm^?2 higher maximum output power density than the one equipped with the random copolymer membrane SR3 (with the same IEC), indicating much better performance of the former. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2304–2313     

Effects of lithium salt and poly(4‐vinyl phenol) on crystalline and amorphous phases in poly(ethylene oxide)

Effects of a strong‐interacting amorphous polymer, poly(4‐vinyl phenol) (PVPh), and an alkali metal salt, lithium perchlorate (LiClO₄), on the amorphous and crystalline domains in poly(ethylene oxide) (PEO) were probed by differential scanning calorimetry (DSC), optical microscopy (OM), and Fourier transform infrared spectroscopy (FTIR). Addition of lithium perchlorate (LiClO₄, up to 10% of the total mass) led to enhanced T_g's, but did not disturb the miscibility state in the amorphous phase of PEO/PVPh blends, where the salt in the form of lithium cation and ClO anion was well dispersed in the matrix. Competitive interactions between PEO, PVPh, and Li⁺ and ClO ions were evidenced by the elevation of glass transition temperatures and shifting of IR peaks observed for LiClO₄‐doped PEO/PVPh blend system. However, the doping distinctly influenced the crystalline domains of LiClO₄‐doped PEO or LiClO₄‐doped PEO/PVPh blend system. LiClO₄ doping in PEO exerted significant retardation on PEO crystal growth. The growth rates for LiClO₄‐doped PEO were order‐of‐magnitude slower than those for the salt‐free neat PEO. Dramatic changes in spherulitic patterns were also seen, in that feather‐like dendritic spherulites are resulted, indicating strong interactions. Introduction of both miscible amorphous PVPh polymer and LiClO₄ salt in PEO can potentially be a new approach of designing PEO as matrix materials for electrolytes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3357–3368, 2006     

Effect of fullerene on radical polymerization of vinyl acetate

The effect of fullerene (C₆₀) on the radical polymerization of vinyl acetate (VAc) with dimethyl 2,2′‐azobisisobutyrate (MAIB) in benzene was investigated kinetically and by means of ESR. C₆₀ was found to act as an effective inhibitor in the present polymerization. All C₆₀ molecules used were incorporated into poly(VAc) during polymerization. The relationship of induction period and initiation rate reveals that a C₆₀ molecule can trap 15 radicals formed in the polymerization system. The polymerization rate (R_p) after the induction period is given by R_p = k [MAIB]^0.6 [VAc]^2.0 (60 °C), which is similar to that observed in the absence of C₆₀. Stable fullerene radical (C) was observed in the polymerization system by ESR. The C concentration increased with time and was then saturated. The saturation time well corresponds to the induction period observed in the polymerization. About 20% of C₆₀ molecules added could survive as stable C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2572–2578, 2000     

SET–LRP of N‐isopropylacrylamide in the presence of chain transfer agent

In this study, single electron transfer‐living radical polymerization (SET–LRP) of N‐isopropylacrylamide (NIPAM) in the presence of 2‐mercaptoethylamine chain transfer agent (CTA) was carried out by Cu(0) generated in situ from the disproportionation of CuBr/2,2′‐bipyridine (2,2′‐bpy) in N,N‐dimethylformamide (DMF) at 90 °C. Analysis of polymerization kinetics in the presence of CTA showed that the premature termination of growing polymer chains leads to retardation. The apparent rate constant of polymerization (k) decreased from 4.49 × 10^?4 to 2.59 × 10^?4 min^?1 with increasing CTA concentration. The initiator efficiency (I_eff) and the chain transfer constant (C_s) were found to be 0.524 and 0.286, respectively. The molecular weights of poly(N‐isopropylacrylamide) [poly(NIPAM)] produced were significantly higher than the predicted values, and the polydispersities were less than 1.22. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Proton‐conducting poly(vinylpyrrolidon)–polyphosphoric acid blends

Anhydrous, proton‐conducting polymer electrolytes of poly(vinylpyrrolidon) (PVP) with polyphosphoric acid (PPA) were prepared. PVP‐x‐PPA blends were obtained for 0.5 ≤ x ≤ 3, where x was the number of moles of PO per polymer repeat unit. Fourier transform infrared studies indicated protonation of the carbonyl group in the five‐member ring. Thermogravimetric analysis showed that these materials were stable up to about 180 °C. Differential scanning calorimetry data demonstrated that the addition of the acid plasticized the material, shifting the glass‐transition temperature from 180 °C for the pure polymer to ?23 °C for x = 3. The temperature dependence of the mechanical properties was investigated with shear experiments. The direct‐current conductivity increased with x and reached about 10^?5 S/cm at ambient temperature. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1987–1994, 2001     

Locally sulfonated poly(ether sulfone)s with highly sulfonated units as proton exchange membrane

Novel locally sulfonated poly(ether sulfone)s with highly sulfonated units were successfully synthesized for fuel cell applications. Poly(ether sulfone)s were prepared by the nucleophilic substitution of bis(4‐fluorophenyl) sulfone with 1,2,4,5‐tetrakis([1,1′‐biphenyl]‐2‐oxy)‐3,6‐bis(4‐hydroxyphenoxy)benzene and bis(4‐hydroxyphenyl) sulfide, followed by oxidation using m‐chloroperoxybenzoic acid. The desired highly sulfonated units were easily introduced by postsulfonation and each one had ten sulfonic acid groups. The sulfonated polymers gave tough, flexible, and transparent membranes by solvent casting. The high contrast in polarity between highly sulfonated units and hydrophobic poly(ether sulfone) units enabled the formation of defined phase‐separated structures and well‐connected proton paths. The sulfonated polymers exhibited excellent proton conductivity over a wide range of relative humidities. The proton conductivity of the sulfonated polymer with an ion exchange capacity value of 2.38 mequiv/g was comparable to that of Nafion 117 even at 30% relative humidity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3444–3453, 2009     

Synthesis,properties, and gas permeability of novel poly(diarylacetylene) derivatives

Poly(diphenylacetylene)s having various silyl groups are soluble in common solvents, from whose membranes poly(diphenylacetylene) membranes can be obtained by desilylation. The oxygen permeability coefficients of the desilylated polymers are quite different from one another (120–3300 barrers) irrespective of the same polymer structure. When bulkier silyl groups are removed, the oxygen permeability increases to larger extents. Poly[1-aryl-2-p-(trimethylsilyl)phenylacetylene]s are soluble in common solvents, and afford free-standing membranes. These Si-containing polymer membranes are desilylated to give the membranes of poly[1-aryl-2-phenylacetylene]s. Both of the starting and desilylated polymers show very high thermal stability and high gas permeability. 1-Phenyl-2-p-(t-butyldimethylsiloxy)phenylacetylene polymerizes into a high-molecular-weight polymer. This polymer is soluble in common organic solvents to provide a free-standing membrane. Desilylation of this membrane yields a poly(diphenylacetylene) having free hydroxyl groups, which is the first example of a highly polar group-carrying poly(diphenylacetylene). The P/P and P/P permselectivity ratios of poly(1-phenyl-2-p-hydroxylphenylacetylene) membrane are as large as 47.8 and 45.8, respectively, while keeping relatively high P of 110 barrers. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5028–5038, 2006     

Synthesis and properties of amine‐containing poly(arylene ether sulfone) as an anion‐exchange matrix

Poly(arylene ether sulfone) (PSF), showing good thermal stability and excellent mechanical properties, was synthesized as an anion‐exchange matrix. It was synthesized by the condensation polymerization between bisphenol A and 4,4′‐dichlorodiphenylsulfone. 1°‐Amine‐containing poly(arylene ether sulfone) (1°‐APSF) was synthesized by the reduction reaction of a nitrated PSF. Then, it was transferred to 3°‐amine‐containing poly(arylene ether sulfone) (3°‐APSF) by the alkylation of the amine of 1°‐APSF. The properties of PSF, 1°‐APSF, and 3°‐APSF were investigated by Fourier transform infrared, ¹H NMR spectroscopy, differential scanning calorimetry, and thermogravimetric analysis. The introduction of the 3°‐amine group into PSF increased the glass‐transition temperature but decreased thermooxidative stability. The ion‐exchange capacities of 1°‐APSF and 3°‐APSF were shown to be 2.24 and 2.86 mequiv/g, respectively. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4281–4287, 2002