Magnetization temperature dependence in Fe/Cr superlattices

We report the temperature dependence of the saturation magnetization, M_s(T), of Fe(t)/Cr(40 Å) superlattices grown on MgO(1 0 0) and MgO(1 1 0) and its variation with Fe-layer thickness (5 Å<t<80 Å). The structure was characterized by X-ray diffraction. M_s(t) vs. T, as measured by DC magnetization and ferromagnetic resonance, show a large interface effect. The origins of this effect are discussed.     

Surface structure and composition of flat titanium thin films as a function of film thickness and evaporation rate

To correlate flat titanium film surface properties with deposition parameters, titanium flat thin films were systematically deposited on glass substrates with various thicknesses and evaporation rates by electron-beam evaporation. The chemical compositions, crystal structure, surface topographies as well as wettability were investigated by using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), atomic force microscopy (AFM) and water contact angle measurement, respectively. The films consisted mainly of TiO₂. Small percentages of Ti₂O₃ and metallic Ti were also found at the film surface using high-resolution XPS analysis. Quantitative XPS showed little differences regarding elemental compositions among different groups of films. The films were obtained by varying the deposition rate and the film thickness, respectively. XRD data showed consistent reflection patterns of the different titanium samples deposited using different film thicknesses. Without exception measurements of all samples exhibited contact angles of 80° ± 5°. Quantitative AFM characterization demonstrated good correlation tendency between surface roughness and film thickness or evaporation rate, respectively. It is important to notice that titanium films with different sizes of grains on their surfaces but having the same chemistry and film bulk structure can be obtained in a controllable way. By increasing the film thickness and evaporation rate, the surface roughness increased. The surface morphology and grain size growth displayed a corresponding trend. Therefore, the control of these parameters allows us to prepare titanium films with desired surface properties in a controllable and reproducible way for further biological investigations of these materials.     

The use of macroscopic modelling of intermetallic phases in aluminium alloys in the study of ferricyanide accelerated chromate conversion coatings

Chromate conversion coatings are used on aluminium alloys, primarily for their renowned corrosion resistant properties. Although these coatings are in common industrial use, neither the protection mechanisms, nor the coating interation with the intermetallic precipitation phases are fully understood. Macroscopic models have been developed in order to represent the galvanic cells present in aluminium alloys due to the presence of such intermetallic particles. Particles modelled include CuAl₂, FeAl₃ and Cu₂FeAl₇, all know to be cathodic to the aluminium matrix. Variations in deposition, both in composition and thickness, are indicative of the mechanisms of deposition over each phase. Characterisation of the coating deposition was carried out using X-ray photoelectron spectroscopy, Rutherford backscattering spectroscopy, Auger electron spectroscopy, scanning electron microscopy with X-ray analysis. Depositional characteristics have been determined for each phase. The coating on the intermetallic phases is primarily Al oxide, and is significantly thinner than the coating on the matrix. This coating on the matrix consists mainly of a mixed Cr/Al oxide. The coating on the intermetallic phases was only one tenth the thickness of the matrix coating, and contained higher levels of Fe, Al and O. Matrix coating chemistry predominated with Cr, O, Fe and N, indicative of a chromate conversion coating. The mechanism for reduced rates of deposition over intermetallic phases was found to be affected by fluorine ion attack leading to intermetallic de-alloying and decomposition of Fe(CN)₆²⁻ accelerator into amide groups on the matrix.     

Thickness-dependent coercivity of ultrathin Co films on a rough substrate: Cu-buffered Si(111)

The hysteresis loops, of Co films with thicknesses ranging from 12- to 80-monolayer-equivalent (MLE) coverages grown by thermal evaporation on a Cu-covered Si(111) surface, were measured in situ by the surface magneto-optic Kerr effect (SMOKE) technique. The hysteresis loops were measured as a function of Co coverage under an external sinusoidal magnetic field at fixed driving frequency. The coercivity H_c of the Co film versus thickness t followed a power law t⁻ⁿ with n=0.4±0.1 between 12 and 44 MLE, and stabilized after 44 MLE, up to the 80 MLE studied. The surface morphology of the 80-MLE Co film was imaged ex situ by atomic force microscopy (AFM) and scanning tunneling microscopy (STM), revealing cauliflower-like islands that were rough both in the short and long range. Analysis of the height–height correlation function for the largest image gave measurements of the effective roughness exponent (0.8), the vertical interface width w(2500 Å), and the lateral correlation length ξ(10 000 Å). We suggest that the coercivity changed in part due to changes in roughness of the Co films, deposited on a rough substrate; the spatial roughness would create an additional surface anisotropy, contributing to a fluctuation in the domain wall energy, resulting in a roughness-dependent coercivity.     

Structural properties of diamond fine particles and clusters prepared by detonation and decomposition of TNT

The thermal parameter B for three different particle sizes of diamond samples (bulk powder 1–4 μm, fine particle 144–195 Å and cluster 55–61 Å) was determined by the grazing incidence X-ray diffraction method. The values of B were found to be in the range 0.50–0.70 Å² for particles in the size range 195–55 Å and 0.27 Å² for 1–4 μm. All of them are larger than that of diamond bulk. A clear size dependence of B, increasing with decreasing particle size, was found. By analysing X-ray diffraction data at several temperatures the magnitude of B was found to be due to B_S (static part) instead of B_T (dynamic part). The average B_S values obtained were 0.04 Å², 0.19 Å² and 0.27 Å² for bulk powder, fine particle and cluster samples respectively. Ultrahigh resolution transmission electron microscope (TEM) observation confirmed the presence of strain, distortion, roughness and dislocation lines in many particles. TEM images of particles indicate that the clusters were not spherical in shape; they were mostly cubiform and some were truncated prism-like polyhedral. The present study reveals that the B_S component is responsible for the large B value in diamond fine particles and clusters. No clear surface local atomic distortion was found in the particles.     

Deposition of lead iodide films on Rh(1 0 0) electrodes from colloidal solutions––the effect of an iodine adlayer

The growth of PbI₂ precipitates on single crystal substrates from colloidal solutions has been investigated with in air scanning tunneling microscopy and synchrotron-based X-ray photoelectron spectroscopy. The PbI₂ growth on Rh(1 0 0) results in nano-clusters with lateral dimensions between 30 and 60 Å, consistent with earlier reports. However, the growth of PbI₂ on a well-ordered iodinated Rh(1 0 0), denoted as (√2×√2)R45°-I, leads to atomically smooth PbI₂ films having a hexagonal symmetry with lattice constant identical to the bulk value of 4.5 Å. The heteroepitaxy is believed to be effected by the atomic iodine monolayer that helps to accommodate large lattice mismatch between PbI₂ and Rh surface with short-range van der Waals interaction.     

On the growth of conversion chromate coatings on 2024-Al alloy

The initial growth of chromate conversion coatings on aluminium 2024-T3 alloy has been investigated by scanning Auger microscopy, scanning electron microscopy and X-ray photoelectron spectroscopy. The coating initiation is shown to be influenced by the alloy microstructure. In agreement with previously proposed growth models, Cr(VI) to Cr(III) reduction begins on the Al-Cu-Fe-Mn intermetallic second-phase particles, which act as cathodic sites, and then over the entire Al matrix surface. The less noble Al-Cu-Mg second-phase particles demonstrate dual behaviour during the initial stage of coating; some dealloy, with formation of a Cu-rich sponge-like structure, while others show no evidence for etching during the first few seconds and coating deposits on them similar to the situation for the Al-Cu-Fe-Mn particles. XPS measurements show more Cr(III) at the very initial stage of nucleation and growth, whereas the amount of Cr(VI) in the coating increases with the length of the chromating treatment. This is discussed in relation to Raman spectroscopy measurements made in a separate study.     

Structural characterization of ultrathin Cr and Sc films for soft X-ray mirrors

The structure of multilayers of ultrathin scandium (Sc) and chromium (Cr) films has been characterized by means of transmission electron microscopy (TEM). Face centered cubic Sc was found both in magnetron sputtered thin Sc layers on Si(0 0 1) and in Cr/Sc multilayers for soft X-ray mirrors. The single Sc and Cr layers are polycrystalline with randomly oriented grains, while Sc and Cr within the Cr/Sc multilayer show a strong [0 0 1] texture in the deposition direction. From high-resolution images the orientation-relationship at the Cr/Sc interfaces could be deduced as: Sc_[110]//Cr_[100] and Sc_[010]//Cr_[110], which was confirmed by image simulations.     

Hydroxyapatite coating on porous silicon substrate obtained by precipitation process

Hydroxyapatite Ca₁₀(PO₄)₆(OH)₂ (HAP) is known as a bioactive and biocompatible material, HAP coatings were used to improve the biocompatible of substrate by many researcher, In this work, HAP thin films on porous silicon (PS) substrates have been prepared by aqueous precipitation method with rapid thermal annealing (RTA) processes. The HAP films had been prepared under the annealing temperature ranging from 300 to 1000 °C. By the measurement of X-ray diffraction (XRD), it was found that for the crystallinity optimization, the heat-treatment at 850–950 °C for 1 h would be favorable. Atomic force microscopy (AFM) and scanning electron microscope (SEM) measurements reveal a dense and smooth surface of the HAP film, and tightly adherence of the coating on porous silicon substrate after sintered. Thus, by this method, porous silicon could be increased its bioactivity and so that could be used in the biomedical area.     

Formation of high quality gallium nitride thin films on Ga-diffused Si(1 1 1) substrate

High quality gallium nitride thin films have been successfully grown on the Ga-diffused Si(1 1 1) substrates through ammoniating Ga₂O₃ thin films deposited by r.f. magnetron sputtering. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), atomic force microscope (AFM) and photoluminescence (PL) were used to characterize the synthesized samples. The analyses reveal that the formed films are high quality polycrystalline hexagonal gallium nitride. The as-formed GaN films show a flat surface topography with RMS roughness varied from 29 to 48 Å. The strong near-band-edge-emission peak around 368 nm was observed at room temperature. This is a novel method to fabricate GaN thin films based on the direct reaction between Ga₂O₃ and NH₃ on the Ga-diffused Si(1 1 1) substrates.     

Study on crystalline to amorphous structure transition of Cr coatings by magnetron sputtering

The influence of deposition rate on crystalline to amorphous microstructure transition of Cr coatings was studied through preparation of Cr coatings deposited onto silicon wafers using magnetron sputtering technique. The microstructure and morphology of Cr coatings were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Results show that Cr coating prepared at 400 W exhibits dense columnar crystalline structure and the crystallite size and crystallization rate are increased expressly in the initial 5 min. When the deposition rate achieved to the maximum, Cr coating shows a case of infinite periodic renucleation where new crystals are assumed to be nucleated periodically on the surfaces of growing crystals and strong persistence of the columnar growth morphology is apparent. However, Cr coating exhibits overall microstructure of amorphous phase mixed with a few nano-crystal grains as the deposition rate decreases to the minimum.     

Surface properties of Hafnium diboride(0 0 0 1) as determined by X-ray photoelectron spectroscopy and scanning tunneling microscopy

The surface structure and properties of the HfB₂(0 0 0 1) (Hafnium diboride, HfB₂) surface have been investigated with X-ray photoelectron spectroscopy, low energy electron diffraction (LEED), and scanning tunneling microscopy (STM). Annealing temperatures above 1900°C produce a sharp (1×1) LEED pattern, which corresponds to STM images showing flat (0 0 0 1) terraces with a very low contamination level separated by steps 3.4 Å in height, corresponding to the separation of adjacent Hf planes in the HfB₂ bulk structure. For lower annealing temperatures, extra p(2×2) spots were observed with LEED, which correspond to intermediate terraces of a p(2×1) missing row structure as observed with STM.     

Properties of solvent-free perylene iodine

The perylene iodine system was prepared by a vapour-phase reaction without the use of solvents. Compositions between peryleneI₂ and peryleneI₆ were synthesized and studied by gravimetric analysis, infrared spectroscopy, X-ray diffraction and temperature-dependent resistivity measurements. Infrared spectra in the region 400–4000 cm⁻¹ taken after different amounts of iodine were removed from the sample are distinct from perylene with new absorption lines at 1551 and 1302 cm⁻¹ and shifts of some perylene frequencies. Powder X-ray diffraction measurements indicate that the lattice is monoclinic with parameters a=11.65 Å, b=10.85 Å, c=10.1 Å, β=100.5°. The (1 0 0) reflection, which is forbidden in the space group of perylene, is observed from the compound. The material is electrically conductive and obeys Ohm's law at high temperatures. At low temperatures and high currents, nonlinear effects are observed. The conductivity of the material increases to 1.0 (Ω cm)⁻¹ at room temperature as the iodine content increases to a composition of peryleneI₆. The resistivity obeys an exponential temperature dependence.     

Nanosized titania encapsulated silica particles using an aqueous TiCl4 solution

In this study, sub-micron sized silica particles were encapsulated with nanosized titania particles using an aqueous TiCl₄ solution. The particle size distribution of the synthesized titania particles in the coating layer was estimated to be 10 nm from X-ray powder diffraction and transmission electron microscopy. The thickness of the coating layer ranged from a few nm to about 30 nm from transmission electron microscopy analysis. Zeta potential analysis demonstrated the presence of a titania particle coating layer and the extent of its coverage on the surface of silica particles. X-ray photoelectron spectroscopy analysis also demonstrated that titania particles were successfully deposited on the surface of core silica particles from the chemical shift of binding energies of O 1s, Ti 2p and Si 2p.     

Solid-phase epitaxy of CaSi2 on Si(1 1 1) and the Schottky-barrier height of CaSi2/Si(1 1 1)

Thin Ca films were evaporated on Si(1 1 1) under UHV conditions and subsequently annealed in the temperature range 200–650 °C. The interdiffusion of Ca and Si was examined by ex situ Auger depth profiling. In situ monitoring of the Si 2p core-level shift by X-ray photoemission spectroscopy (XPS) was employed to study the silicide formation process. The formation temperature of CaSi₂ films on Si(1 1 1) was found to be about 350 °C. Epitaxial growth takes place at T≥400 °C. The morphology of the films, measured by atomic force microscopy (AFM), was correlated with their crystallinity as analyzed by X-ray diffraction (XRD). According to measurements of temperature-dependent I–V characteristics and internal photoemission the Schottky-barrier height of CaSi₂ on Si(1 1 1) amounts to qΦ_Bn=0.25 eV on n-type and to qΦ_Bp=0.82 eV on p-type silicon.     

Determination of the K adsorption site on Fe(1 1 0) with XSW

We have used X-ray standing waves (XSW) in near normal incidence to determine the K–Fe bond length and the adsorption site of K at the saturation coverage at room temperature on the Fe(1 1 0) surface. Three different scattering geometries were used to enable the determination of the adsorption site by triangulation. From the results we conclude that the potassium atoms adsorb in a distorted hexagonal overlayer. The Fe–K distance, as determined from the measurements in the (2 2 0) Bragg reflection, is 3.4±0.2 Å. The long bridge site seems to be the preferred adsorption site for the potassium atoms in the distorted hexagonal overlayer. This geometry not only fits all the XSW data, but also explains all spots in the LEED pattern without the need to introduce multiple scattering. Comparison of the measured and simulated XSW data, based on the distorted hexagonal overlayer, enables a more accurate determination of the Fe–K bond length to 3.36±0.14 Å. This corresponds to a potassium hard sphere radius of r_K=2.12±0.14 Å. This radius is among the largest reported for potassium on a metal, which is attributed to the high coverage and coordination of the K atoms in this overlayer arrangement.     

Rietveld refinement and electronic structure studies for the Sm2FeMnO6 new complex perovskite

We report synthesis and crystalline structure study of the Sm₂FeMnO₆ new complex perovskite, by X-ray diffraction experiments and through the application of Rietveld refinement. Results revealed the crystallization of system in a structure given by Pmn21 (#31) space group and lattice parameters a=7.621(1) Å, b=5.675(3) Å and c=5.378(3) Å. Ab initio calculations of density of states (DOS) and electronic structure were carried out for this perovskite-like system by the density functional theory (DFT) and using the full-potential linearized augmented plane waves (FP-LAPW) method. All calculations were carried out using spin polarization. Material evidences a conductor-like character, predominantly due to d–xy Fe orbital of the spin down channel. Magnetic response of system has contributions of Fe and Mn spin up orientation. The calculated magnetic moment in cell was 34.48 μ_B and the magnetic moment in interstitial was 1.54 μ_B.     

X-ray diffraction evidence of the single solid solution character of bi-metallic Pt-Pd catalyst particles on an amorphous SiO2 substrate

An X-ray diffraction study was carried out on powders of a series of catalysts prepared from aqueous solutions of H₂PtCl₆ and PdCl₄ and amorphous SiO₂ with different concentrations in weight of Pt and Pd at about 4% in overall metallic weight. Measurements of the position of high angle Bragg reflections in the diffractograms show evidence of the fact that the small catalyst particles are bi-metallic Pt-Pd crystals having a face-centred cubic Bravais lattice. The lattice constant of these crystals was found to change with the relative concentration of Pt and Pd by following the Vegard’s rule. This correlation leads to the conclusion that the bi-metallic catalyst particles are made of a single solid solution of Pt and Pd atoms in the whole range of relative concentrations. Relative concentrations of these metals in the samples under study were determined by using energy dispersive X-ray spectrometry and their values were found to be close to the stochiometric relative concentrations in weight of the metals in the precursor aqueous solution. An average size of about 96 Å was estimated for the bi-metallic particles from the full-width at half-maximum value measured for the (2 0 0) diffractometric curve.     

Influence of NH beam bombarding energy on structural characterization and cell attachment of CNx coating

The carbon nitride (CN_x) coating with its novel properties will be excellent candidate for biomedical applications. CN_x coatings were prepared on the surface of Ti–6Al–4V by ion-beam-assisted deposition (IBAD) with different NHⁿ⁺ beam bombarding energies at low substrate temperature. The coatings were characterized by Scanning electron microscopy (SEM), Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and Fourier-transform infrared (FTIR) spectroscopy. The result showed that the wear-resistance of CN_x coatings was better at higher beam bombarding energy. The cell attachment tests also gave interesting results that CN_x coatings exhibited low macrophage attachment and provide desirable surface for the normal cellular growth and morphology of the fibroblasts. Structural analysis showed that NHⁿ⁺ beam bombardment at the energies of 300–400 eV could result in more nitrogen concentration and fraction of sp³CN bonds in the structure of CN_x coatings, which may be responsible for the improvement in the wear-resistance and the cell attachment.     

Electronic structure investigation of the Ag(1 1 0)(n×1)O surfaces––new photoemission results for an old problem

We have used angle-resolved photoelectron spectroscopy to investigate the occupied antibonding electron states of the Ag(1 1 0)(n×1)O surface along different directions in the surface Brillouin zone. We present experimental evidence that several earlier results obtained along (along the Ag–O chains) contain admixtures from contamination, most probably from carbonate-like contributions. New results are obtained along and (perpendicular to the chains). These data indicate that the n=2 structure is stabilized by repulsive electronic interaction between neighbouring chains, which diminishes drastically for n=3 and disappears almost completely at n4. This observation points to a strain field within the substrate which stabilizes the geometry between n=3 (interchain distance 8.7 Å) and n=8 (23.1 Å). Its existence is indirectly seen in the n-dependence of the surface phonon energies at , which can be explained quantitatively by umklapp-processes induced by the lateral periodicity of the strain field. We compare our photoemission results for (2 × 1)O with available surface band structure calculations.