Sorption of uranium from alkaline waste onto radiation grafted phosphoryl-g-Teflon matrix

High energy ⁶⁰Co γ-radiation was used to graft glycidylmethacrylate onto Teflon scrap through mutual radiation grafting technique. The epoxy ring of grafted polyGMA chains were later converted to U selective phosphoryl group, chemically. The grafted matrix was used as solid–liquid adsorbent of uranium from alkaline waste solution. More than 98% recovery of uranium from alkaline waste (~pH 8) solution was achieved. The effect of grafting extent on adsorption kinetics was also investigated. The selectivity of uranium extraction over other fission products was established. The uptake of other fission products was <5% for equilibration time of ~1 h.

     

Interaction Between Liposomes and Neutral Polymers: Effect of Adsorption on Drug Release

The processes of adsorption of two neutral polymers (poly(vinyl pyrrolidone), PVP and poly(vinyl alcohol), PVA) were investigated on liposomes composed of soy lecithin/dicetyl phosphate/cholesterol = 25:2:3 (molar ratio). The liposomes were prepared in buffered solution at pH = 7.4 and mixed with the solution of the measured polymers in the desired polymer/lipid (w/w) ratios. Adsorption was measured by determination of the equilibrium bulk concentration of the polymer. In the case of PVA quantitative adsorption measurements with a specific reagent were possible. Adsorption isotherms were recorded at 25 ± 1°C. It was concluded that adsorbed and unadsorbed PVA molecules are in equilibrium even at low polymer/ lipid ratios. The results were confirmed by dynamic laser light scattering (DLS), and thermal activity monitoring (TAM) experiments. Another group of the liposomes was prepared in 60 mM ammonium sulphate (pH = 5.0) and we filled the vesicles with a test dye, acridine orange (AO) using the pH-gradient (remote loading) method. The AO release property of liposomes was tested with a special vertical diffusion cell after we had made PVA adsorb on their surface in different PVA/lipid (w/w) ratios.     

Leveraging Actinide Hydrolysis Chemistry for Targeted Th and U Separations using Amidoxime-Functionalized Poly(HIPE)s

P olymerized h igh i nternal p hase e mulsions (poly(HIPE)s) are porous polymer monoliths whose synthesis can easily be tailored to allow incorporation of functional units. In this work, nitrile containing poly(HIPE)s have been prepared with either acrylonitrile (AN) or 4-cyanostyrene (4CS) comonomers. Post-synthetic modification of these nitrile-containing poly(HIPE)s yields their corresponding amidoximated analogues, which were studied for actinide uptake. These amidoxime-functionalized, porous polymers were shown to adsorb 95 % Th⁴⁺ species from aqueous solution within 30 minutes. In contrast to other amidoxime containing polymers the uptake of UO₂²⁺ in these poly(HIPE)s is lower under similar conditions. A critical analysis of actinide separations and high-energy X-ray scattering data provides insight into the polymers’ selectivity, enabled by the uptake of multinuclear Th clusters.     

Ultrasonic Degradation and Copolymerization of Poly (Vinyl Alcohol) with Acrylonitrile

The ultrasonic degradation of poly(vinyl alcohol) (PVA) in aqueous solution and copolymerization of PVA with acrylonitrile (AN) were studied. It is confirmed that the rate of degradation of PVA follows the kinetic equation suggested by Baramboim. Both water-soluble and water-insoluble copolymer can be obtained by changing the irradiation time or the amount of AN added to the aqueous solution of PVA. The structure of the copolymer was identified by IR, MS, PGC, and x-ray diffraction. The copolymer prepared is mainly a block one. By irradiating 2% PVA/AN (1/1.6, w/w) at 20 ± 1°C and 21. 5 kHz with 490 W for 28 min, the yield of water-soluble copolymer is 25.49%, the AN content in which is 13.98%. After 100 min, with the weight ratio between PVA and AN 1/4, the yield of the water-insoluble copolymer amounted to 296.01%, the AN content in which is 75.56%.     

The effects of sodium chloride on the explosive performance of ammonium nitrate

Sodium chloride (NaCl) was added to the ammonium nitrate (AN) by different mixing methods. The heat sensitivity performance and the explosive performance of AN and ammonium nitrate fuel oil (ANFO) were studied by using differential scanning calorimeter (DSC), the UN gap test and Koenen test. The results show that: When AN contained 15 % (solution mixing) and 35 % (mechanical mixing) additive, AN maximum exothermic peak increased from 286.75 to 300.63 and 307.83 °C, respectively. For the mechanical mixing, the critical values of the UN gap test and Koenen test AN were 35 and 40 %. The ANFO both were 50 %; for the solution mixing, AN were 15 and 40 %, the critical value of the UN gap test, ANFO was 25 %. AN and ANFO contain more than the critical value of additive, the AN and ANFO would not be detonated.     

Surface modification of cellulose nanocrystal with chitosan oligosaccharide for drug delivery applications

A novel drug delivery system based on two of the most abundant natural biopolymers was developed by modifying the surface of oxidized cellulose nanocrystal (CNC) with chitosan oligosaccharide (CS_OS). First, the primary alcohol moieties of CNC were selectively oxidized to carboxyl groups using the 2,2,6,6-tetramethylpiperidine-1-oxyl radical catalyst. The amino groups of CS_OS were then reacted with carboxylic acid groups on oxidized CNC (CNC-OX) via the carbodiimide reaction using N-hydroxysuccinimide and 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide as coupling agents. Successful grafting of CS_OS to CNC-OX was confirmed by infrared spectroscopy, thermogravimetry, potentiometric titration, and zeta potential measurements. The grafting resulted in a conversion of ~90 % carboxyl groups on CNC-OX and the degree of substitution was 0.26. CNC–CS_OS nanoparticles showed a binding efficiency of 21.5 % and a drug loading of 14 % w/w. A drug selective electrode was used to directly measure the concentration of procaine hydrochloride released from CNC–CS_OS particles. The in vitro drug release was studied at pH 8 and the nanoparticles revealed a fast release of up to 1 h, which can be used as biocompatible and biodegradable drug carriers for transdermal delivery applications.     

Utilization of low-cost sorbent for removal and separation of 134Cs, 60Co and 152+154Eu radionuclides from aqueous solution

Eggshell material was used as low-cost and eco-friendly biosorbent for removal of ¹³⁴Cs, ⁶⁰Co and ^152+154Eu radionuclides from aqueous solution. The eggshell material was calcined at 500 and 800 °C, and then characterized. Comparative studies on the natural and calcined eggshell for sorption of the three radionuclides were carried out. It was found that, the uptake is in the order: Eu(III) > Co(II) > Cs(I). Further, column chromatography was used in separation of ¹³⁴Cs, ⁶⁰Co and ^152+154Eu using 0.15, 0.2 and 0.5 mol/l nitric acid, respectively. Eggshell material can be considered as a promising material for separation of radionuclides from radioactive waste solution.     

Preparation of Latexes with Poly(Methyl Methacrylate) Cores and Hydrophilic Polymer Shells Containing Amino Groups

Abstract

Functional latexes with poly(methyl methacrylate) (PMMA) cores and amino‐containing, water‐soluble polymer shells were synthesized via direct graft copolymerization of methyl methacrylate from water‐soluble polymers induced by a small amount of tert‐butyl hydroperoxide (TBHP) at 80°C for 2 h. Amphiphilic graft copolymers and PMMA homopolymers were generated concurrently to form highly monodispersed latexes. The effects of water‐soluble polymer containing different amino group, reaction temperature, TBHP concentration, molecular weight of the polymer and pH of the solution on conversion and grafting efficiency of the monomer and particle size were investigated. Transmission electron microscopic images of the PMMA/poly(ethyleneimine) (PEI) and PMMA/poly(allylamine) (PAA) particles clearly show well‐defined core‐shell morphologies, where PMMA cores are coated with either PEI or PAA shell. The amino‐containing polymer shells were also confirmed with zeta‐potential measurements. Furthermore, the amino‐containing latexes can be produced with a solids content up to 22 wt.%. Thus, this method provides a commercially viable route to functional latexes.     

Miscibility and Mechanical Behavior of SAN/NBR Blends

Summary: Aiming the development of high toughness polymer materials, blends of poly(styrene-co-acrylonitrile) (SAN) and poly(butadiene-co-acrylonitrile) (NBR) rubbers, with contents of acrylonitrile (AN) varying from 21 to 45%, were prepared by casting, coprecipitation and monoscrew extrusion followed by injection molding. SAN/NBR blends, prepared in the compositions (w/w) 90/10, 80/20, 70/30, 60/40, and 50/50, were characterized by differential scanning calorimetry (DSC) and Izod impact tests. DSC analyses showed that blends with 33% AN NBR prepared by casting, and with 39% AN NBR prepared by coprecipitation, are partially miscible at 60/40, 70/30 and 80/20 (SAN/NBR) compositions and immiscible for 50/50 compositions. On the other hand, 90/10 SAN/NBR systems were totally miscible. The blends with 45% AN NBR prepared by coprecipitation showed partial miscibility to 50/50, 60/40, 70/30 and 90/10 compositions and total miscibility to 80/20 composition. The NBR addition results in a significant increase in the impact resistance, strongly dependent on the blend composition and the NBR AN content. The best result of impact resistance — 75.2 ± 8.6 (kJ · m⁻²) — was obtained for SAN/NBR 50/50, using 45% AN NBR. This value is 15.7 times bigger than that for pure SAN -4.8 ± 0.7 (kJ · m⁻²).     

A viscosity-tunable polymer for DNA separation by microchip electrophoresis

A thermo-responsive separation matrix, consisting of Pluronic F127 tri-block copolymers of poly(ethylene oxide) and poly(propylene oxide), was used to separate DNA fragments by microchip electrophoresis. At low temperature, the polymer matrix was low in viscosity and allowed rapid loading into a microchannel under low pressure. With increasing temperatures above 25°C, the Pluronic F127 solution forms a liquid crystalline phase consisting of spherical micelles with diameters of 17–19 nm. The solution can be used to separate DNA fragments from 100 bp to 1500 bp on poly(methyl methacrylate) (PMMA) chips. This temperature-sensitive and viscosity-tunable polymer provided excellent resolution over a wide range of DNA sizes. Separation is based on a different mechanism compared with conventional matrices such as methylcellulose. To illustrate the separation mechanism of DNA in a Pluronic F127 solution, DNA molecular imaging was performed by fluorescence microscopy with F127 polymer as the separation matrix in microchip electrophoresis. Figure Temperature dependence of the viscosity of 20% w/w Pluronic F127 solution in 1xTBE buffer. Dotted approximates resultant curve.     

Graft Copolymerization of Benzyl Methacrylate onto Poly(Acryloyl-L-valine) Microspheres by Using the Photoreaction of Side Carboxyl Groups with Lead Tetraacetate

N-Acryloyl-L-valine (ALV) was found to yield polymer microspheres when it was polymerized with a radical initiator in acetophenone. The resulting microspheres showed thermochromism in aromatic solvents such as benzonitrile, methyl benzoate, and acetophenone. Graft copolymerization of benzyl methacrylate (BzMA) onto poly(ALV) microspheres was carried out in benzonitrile by using the photoreaction of carboxyl groups in poly (ALV) with Pb(OAc)₄. The grafting efficiency was not very high (15–28%). Methyl methacrylate as the second monomer gave a higher grafting efficiency (56%) although the polymer yield was considerably lower. The resulting graft copolymer was characterized by IR spectroscopy and thermogravimetry. The grafted poly (ALV) microspheres were well dispersed in benzene. A benzene solution of grafted poly(ALV) microspheres and homopoly(BzMA) gave a film with finely dispersed poly (ALV) microspheres.     

Thermally-activated shape memory behaviour of bionanocomposites reinforced with cellulose nanocrystals

Bionanocomposites with thermally-activated shape memory ability have been designed based on a synthesized poly(ester-urethane) matrix reinforced with both neat and functionalized cellulose nanocrystals. The functionalization of the cellulose nanocrystals was performed by grafting poly(l-lactic acid) (PLLA) chains onto their surface. The matrix has a block copolymer structure of two biodegradable and biocompatible polymers, poly(ε-caprolactone) (PCL) and PLLA. This research is focused on the effects of cellulose nanofillers on the thermally-activated shape memory response of the neat matrix confirming that the bionanocomposites are able to show shape memory effects at 35 °C, close to the human body temperature, making these materials good candidates for biomedical applications. Three thermo-mechanical cycles at 50 % of deformation were performed in order to check the thermally-activated shape memory ability of the bionanocomposites and to determine the shape memory parameters, namely the strain fixity (R_f), and the strain recovery (R_r) ratio. Both bionanocomposites, with neat and functionalized cellulose nanocrystals, present excellent shape memory behaviour maintaining the recovery behaviour at values of about 90 % as measured previously for the pure matrix, indicating that the addition of the nanofiller maintains the good ability to recover the initial shape of the matrix. The cellulose nanofillers clearly improve the ability of the polymer to fix the temporary shape. In fact, the bionanocomposites show R_f at about 90 %. Moreover, bionanocomposites reinforced with the functionalized cellulose nanocrystals maintain constant their performance during all the thermo-mechanical cycles thus confirming that the improvement in the shape memory behaviour can be mainly attributed to the increase of the interactions between the functionalized cellulose nanocrystals with the polymeric matrix.     

Heat-Resistant Polymer-Grafted Carbon Black: Grafting of Poly(Organophosphazenes) onto Carbon Black Surface

Abstract

The grafting of poly(organophosphazenes) onto carbon black surface by the reaction of poly(dichlorophosphazene) (PDCP) with carbon black having sodium phenoxide groups was investigated. PDCP was prepared by the ring-opening polymerization of hexachlorocyclotriphos-phazene in solution using sulfamic acid as a catalyst. The introduction of sodium phenoxide groups onto carbon black was achieved by treatment of phenolic hydroxyl groups on the surface with sodium hydroxide in methanol. Poly(diphenoxyphosphazene) (PDPP) was successfully grafted onto carbon black by the reaction of PDCP with sodium phenoxide groups introduced onto the surface followed by the replacement of chlorine atoms in PDCP with phenoxy groups. The percentage of grafting onto carbon black increased to 206% at 30°C after 12 h. It was found that only 1.4% of sodium phenoxide groups on carbon black surface was used for the grafting of PDCP because of the blocking of the surface by grafted polymer chains. Poly(diaminophenylphosphazene) and poly-(diethoxyphosphazene) were also grafted onto carbon black surface by the treatment of PDCP-grafted carbon black with aniline and sodium ethoxide, respectively. Poly(organophosphazenes)-grafted carbon blacks produced stable colloidal dispersions in good solvents for grafted polymers. Furthermore, thermogravimetric analysis indicated that poly-(organophosphazenes)-grafted carbon blacks were stable in air about 300°C.     

Partial purification of neutron-activation 99Mo from cross-contaminant radionuclides onto potassium nickel hexacyanoferrate(II) column

Potassium nickel hexacyanoferrate(II) matrix was prepared and characterized. Purification of neutron-activation ⁹⁹Mo–molybdate(VI) solutes from some residual cross-contaminant radionuclides including ¹³⁴Cs, ⁸⁶Rb, ¹²⁴Sb, ⁶⁰Co and ⁵¹Cr was carried out onto small chromatographic columns of the matrix (each of 1.0 g). Gamma-ray spectrometric analysis data showed that the purification process was not affected by either Mo(VI) concentrations (0.13 and 0.02 M Mo) in the feeding solution of 3.5 M NaNO₃ at pH 9.5 or flow rates (0.2 and 5.0 mL/min) at room temperature. Molybdenum(VI) average loss onto the column matrix did not exceed 7.7 × 10^?2 mmol Mo. Except for ⁵¹Cr, the matrix has very high selectivity for ¹³⁴Cs, ⁸⁶Rb and ¹²⁴Sb with ~50% ⁶⁰Co elimination. The obtained data were briefly discussed.     

Anion-exchange supermacroporous monolithic matrices with grafted polymer brushes of N,N-dimethylaminoethyl-methacrylate

Graft polymerization using potassium diperiodatocuprate as initiator was found to be an effective and convenient method for grafting functional polymer of N,N-dimethylaminoethyl methacrylate (DMAEMA) onto superporous polyacrylamide gels, so-called cryogels (pAAm cryogels). It was possible to achieve grafting degrees up to 110% (w/w). The two-step graft polymerization i.e. first activation of the matrix followed by displacement of initiator solution with the monomer solution, decreased pronouncedly the soluble homopolymer formation. The efficiency of graft polymerization using a two-step technique increased up to 50% (w/w) at a monomer conversion of 10%, compared to 10% graft efficiency with 60-70% monomer conversion for one-step direct graft polymerization. The pAAm cryogels grafted in one-step and two-step procedures, respectively, behaved similarly when binding low-molecular weight ligand but showed very different behavior for sorption of a high-molecular-weight ligand, bovine serum albumin (BSA). The differences in behavior were rationalized assuming different structure of the graft polymer layers and tentacle-type BSA binding to the grafted polymer.     

Production of polyacrylonitrile particles by precipitation polymerization in supercritical carbon dioxide

Polyacrylonitrile particles were produced by precipitation polymerization of acrylonitrile (AN) without any colloidal stabilizer in supercritical carbon dioxide as a polymerization medium at about 30 MPa for 24 h at 65 °C at different initiator concentrations (0.8–45.2 mmol/l) and at different AN concentrations (10–40% w/v). An increase in the initiator concentration led to increases in the conversion and in the degree of coagulation and to a decrease in the molecular weight. At AN concentration of 20% w/v, micron-sized, relatively monodisperse polyacrylonitrile particles with clean and uneven surfaces were produced.     

Grafting of hyperbranched poly(amidoamine) onto carbon black surfaces using dendrimer synthesis methodology

To modify carbon black surface, the surface grafting of hyperbranched poly(amidoamine) onto the surface by using dendrimer synthesis methodology was investigated. Carbon black having amino groups (initiator sites) was prepared by the reduction of surface nitro groups introduced by nitration of aromatic rings. It was found that hyperbranched poly(amidoamine) was propagated from carbon black surface by repeating two processes: (1) Michael addition of methyl acrylate (MA) to surface amino groups and (2) amidation of the resulting esters with ethylenediamine: the percentage of poly(amidoamine) grafting reached to 96.2% after 10th‐generation. The grafting of hyperbranched poly(amidoamine) onto polystyrene‐bead as a model compound of carbon black was also achieved by the above procedures. However, the theoretical propagation of poly(amidoamine) dendrimer was not achieved, because of steric hindrance of grafted polymer. Hyperbranched poly(amidoamine)‐grafted carbon black gave a stable dispersion in a good solvent for poly(amidoamine). Copyright © 2001 John Wiley & Sons, Ltd.     

Preparation of poly(ε-caprolactone)-co-poly(acrylic acid) by radiation-induced grafting

Acrylic acid was grafted onto poly(ε-caprolactone) (PCL) films by using electron beam (EB) preirradiation technique. The effect of reaction time, monomer concentration, radiation dose, time between irradiation and grafting, radiation atmosphere, and polymer crystallinity on the extent of grafting were studied. Silver and tin ions were attached to the grafted chains in order to study the grafting process. The irradiation in air was initially more rapid, but the final extent of grafting was the same when irradiated in nitrogen atmosphere. Maximum grafting extents exceeding 400% could be obtained. The optimal grafting was obtained at an acrylic acid to water ratio of 30 : 70. The grafting process could be initiated at a dose as low as 12 kGy. The grafting process proved to start at the surface and was extended into the bulk with time. The ability to form crystals was reduced as the grafting extent increased. The water uptake of the poly(ε-caprolactone)-graft-poly(acrylic acid) was increasing with increasing grafting extent, but reached a maximum of ca 100% for all grafting extents above 85%. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1805–1812, 1998     

Preparation,characterization and evaluation of a hybrid polymeric coating with sorbent properties

A hybrid polymeric coating (PDMS–CNPrTEOS) with sorbent properties was prepared by the sol–gel method from hydroxyl-terminated poly(dimethylsiloxane) (OH-PDMS), and cyanopropyltriethoxysilane (CNPrTEOS) as an inorganic precursor, using trifluoroacetic acid (TFA) as a catalyst. A coating with the sol–gel solution was prepared on glass plates using the dip-coating method and subsequently characterized. Characterization by FTIR shows that cyano groups are present on the surface coating and contact angle tests show that the coating presents hydrophilic characteristics. The organic–inorganic polymer was stable up to 400 °C with a weight loss of 8 wt % and showed good stability after immersion for 60 min in vortex and 45 min in ultrasonic bath, in various solvents: water, methanol (MeOH), acetone, isooctane, ethyl acetate (AcOEt) and acetonitrile (ACN), and solutions at different pH (1–12) for 48 h (h). The PDMS–CNPrTEOS hybrid polymer was evaluated and was found to have the ability to extract simultaneously furanic compounds in aqueous solution when it is employed as a sorbent for stir bar sorptive extraction (SBSE).     

Influence of solvent type on porosity structure and properties of polymer separator for the Li-ion batteries

Polyethylene-supported polymethyl methacrylate/poly(vinylidene fluoride-co-hexafluoropropylene) separator for gel polymer lithium-ion battery use was prepared with a mixed solvent of n-butanol and acetone. The prepared separator was characterized with scanning electron spectroscopy and X-ray diffraction, and its performance was investigated by electrochemical impedance spectroscopy and battery charge/discharge test. Compared to the separator prepared with acetone, the separator prepared with the mixed solvent shows an enhanced porosity (from 42 to 49 %) and electrolyte uptake (from 104 to 125 %). The ionic conductivity of the corresponding gel polymer electrolyte is improved from 2.81 to 3.39 mS cm^?1, the discharge capacity retention of the LiCoO₂/artificial graphite battery is increased from 95 to 98 % after 100 cycles at 0.5 C, and the discharge capacity of the battery at 1 C increases by 4 %.