Measurement of temperature and refractive index based on surface long-period gratings deposited onto a D-shaped photonic crystal fiber

We propose a surface long-period grating (LPG) based on a D-shaped photonic crystal fiber (PCF). The D-shaped PCF is fabricated by a side-polishing technique. The surface LPG based on periodic patterns of photoresist (PR) is formed by using the spin-coating and the standard contact lithography methods. Resonant coupling is created by the surface PR-LPG in the D-shaped PCF. The resonant peak shifts to longer wavelength as the ambient index is increased and shifts to shorter wavelength as the temperature is increased. The total wavelength shift is measured to be 122 nm in the refractive index range from 1 to 1.45 and the temperature sensitivity is measured to be −0.3 nm/°C in the temperature range from 30 to 100°C.     

Optical refractometer based on large-core air-clad photonic crystal fibers

A large-core air-clad photonic crystal fiber-based sensing structure is described, which is sensitive to refractive index. The sensing head is based on multimodal interference, and relies on a single-mode/large-core air-clad photonic crystal fiber (PCF)/single-mode fiber configuration. Using two distinct large-core air-clad PCF geometries-one for refractive index measurement and the other for temperature compensation, it was possible to implement a sensing head sensitive to refractive index changes in water as induced by temperature variations. The results indicated the high sensitivity of this sensing head to refractive index variations of water, and a resolution of 3.4×10(-5) refractive index units could be achieved.     

一种基于模间干涉的亚波长直径光纤气体折射率传感

设计了一种基于模间干涉的亚波长直径光纤气体折射率传感方案,并分析了其测量灵敏度.将标准单模光纤和一段仅传输基模与二阶模的无包层亚波长直径光纤结合形成传感头,通过分析传感头外气体折射率的变化对两个模式干涉谱峰值移动的影响,研究了这种传感器的折射率测量灵敏度.结果表明,这种传感器的灵敏度高于利用折射率引导型光子晶体光纤的基于模间干涉的折射率传感器.因为没有气体向微孔扩散的过程,这种基于模间干涉的亚波长光纤折射率传感器可用于实时探测.     

Refractive index sensor based on high-order surface plasmon resonance in gold nanofilm coated photonic crystal fiber

We propose a novel kind of wide-range refractive index optical sensor based on photonic crystal fiber(PCF) covered with nano-ring gold film.The refractive index sensing performance of the PCF sensor is analyzed and simulated by the finite element method(FEM).The refractive index liquid is infiltrated into the cladding air hole of the PCF.By comparing the sensing performance of two kinds of photonic crystal fiber structures, a wide range and high sensitivity structure is optimized.The surface plasmon resonance(SPR) excitation material is chose as gold, and large gold nanorings are embedded around the first cladding air hole of the PCF.The higher order surface plasmon modes are generated in this designed optical fiber structure.The resonance coupling between the fundamental mode and the 5 th order surface plasmon polariton(SPP)modes is excited when the phase matching condition is matched.Therefore, the 3 rd loss peaks appear obvious red-shift with the increase of the analyte refractive index, which shows a remarkable polynomial fitting law.The fitnesses of two structures are 0.99 and 0.98, respectively.When the range of refractive indices is from 1.40 to 1.43, the two kinds of sensors have high linear sensitivities of 1604 nm/RIU and 3978 nm/RIU, respectively.     

Numerical analysis of a temperature sensor based on the photonic band gap effect in a photonic crystal fiber

In this paper we investigate, by the plane wave expansion method and an analytical model, the temperature effect on the photonic band gap fiber, and we report on a numerical demonstration of a temperature sensor based on the photonic band gap (PBG) shift in a solid core photonic crystal fiber (PCF) infiltrated with a high refractive index oil. The bandwidth and the position of the central wavelength of the band gap are the parameters of interests for our temperature sensing purpose. Simulation results were found to be in excellent agreement with the refractive index scaling law and the highest sensitivity of 3.21?nm/°C was achieved, and it will be even higher than the grating based sensors written in PCFs with similar structure.     

基于闪耀光纤光栅的折射率传感技术实验研究

提出了一种基于闪耀光纤光栅传感技术的折射率测量新方法,即采用SLED作为光源,通过检测闪耀光纤光栅透射谱强度实现折射率的测量.实验证明,当环境折射率在1.372 3~1.453 2之间变化时,闪耀光纤光栅透射功率从0.611~0.472 mW线性下降,其灵敏度达到1.718 μW/（0.001折射率变化）.该检测方法具有结构简单、无需波长检测、灵敏度高、易于工程化等优点.     

Long period grating cascaded to photonic crystal fiber modal interferometer for simultaneous measurement of temperature and refractive index

We propose and demonstrate a novel and simple dual-parameter measurement scheme based on a cascaded optical fiber device of long-period grating (LPG) and photonic crystal fiber (PCF) modal interferometer. The temperature and refractive index (RI) can be measured simultaneously by monitoring the spectral characteristics of the device. The implemented sensor shows distinctive spectral sensitivities of -30.82 nm/RIU (refractive index unit) and 47.4 pm/°C by the LPG, and 171.96 nm/RIU and 10.4 pm/°C by the PCF modal interferometer. The simultaneous measurement of the temperature and external RI is experimentally demonstrated by the sensor. The temperature shift and RI shift calculated by the sensor matrix agree well with the actual temperature and RI change in the experiment.     

Simultaneous measurement of refractive index and temperature using dual-period grapefruit microstructured fiber grating

By cascading the long period fiber grating (LPFG) and fiber Bragg grating (FBG) in grapefruit microstructured fiber, a novel dual-period fiber grating sensor is proposed. The refractive index and temperature are measured simultaneously by using the different sensitivity of FBG and LPFG. The relationship between dual-period fiber grating transmission spectrum and refractive index, resonant wavelengths and temperature are analyzed theoretically, respectively. The simulation results show that the accuracy of the sensor in measuring refractive index and temperature is estimated to be 2319.6 nm/RIU in a range from 1.33 to 1.36 and 0.017 nm/°C from 0 °C to 100 °C, respectively. Thus, the sensor has high refractive index sensitivity, and can provide the theoretical foundation for the optical fiber biosensor.     

长周期光纤光栅气敏薄膜传感器结构优化

基于三包层长周期光纤光栅模型,研究了包层表面涂覆一层溶胶凝胶气敏薄膜的长周期光纤光栅化学传感器的灵敏度Sn与薄膜光学参量(折射率n3和厚度h3)和光纤光栅结构参量(光栅周期、折变量和光栅长度)之间的关系。采用最优化数值方法,找到了获得高灵敏度所需的最佳膜层光学参量和光栅结构参量。理论计算表明,该类型传感器对膜层折射率的测量分辨率高达10-8。实验上制作了对乙醇气体敏感的传感器,并证实了传感器结构优化的必要性。     

Photonic crystal fiber tip interferometer for refractive index sensing

In this paper we present an interferometer based on photonic crystal fiber (PCF) tip ended with a solid silica-sphere for refractive index sensing. The sensor is fabricated by splicing one end of the holey PCF to a single mode fiber (SMF) and applying arc at the other end to form a solid sphere. The sensor has been experimentally tested for refractive index and temperature sensing by monitoring its wavelength shift. Measurement results show that the sensor has the resolution of the order of 8.7×10(-4) over the refractive index range of 1.33-1.40, and temperature sensitivity of the order of 10 pm/°C in the range of 20-100 °C.     

Temperature sensor based on an isopropanol-sealed photonic crystal fiber in-line interferometer with enhanced refractive index sensitivity

We fabricate a simple, compact, and stable temperature sensor based on a liquid-sealed photonic crystal fiber (PCF) in-line nonpolarimetric modal interferometer. Different from other reported PCF devices, it does not need expensive polarimetric devices, and the liquid is sealed in one fiber. The device consists of a stub of isopropanol-filled PCF spliced between standard single-mode fibers. The temperature sensitivity (-166 pm/°C) increases over an order of magnitude compared with those of the previous sensors based on air-sealed PCF interferometers built via fusion splicing with the same mechanism. In addition, the refractive index sensitivity also increases. Higher temperature sensitivity can be realized by infiltrating some liquid having a higher thermo-optic coefficient into the microholes of the PCF.     

Refractive index sensor based on tapered PCF in-line interferometer

A simple and compact refractive index sensor is demonstrated by tapering a photonic crystal fiber (PCF) in-line interferometer. The PCF is spliced between two single-mode fibers and tapered via hydrofluoric acid etching. Its sensitivity in liquid is more than an order of magnitude larger than the untapered one. By optimizing the etching process, we can fabricate more uniformly and thinly tapered PCF interferometers with higher sensitivity in the future.     

High sensitivity dual core photonic crystal fiber sensor for simultaneous detection of two samples

The optical control ability of photonic crystal fiber (PCF) is a distinctive property suitable for improving sensing and plasma performance. This article proposes a dual-core D-channel PCF sensor that can detect two samples simultaneously, which effectively solves the problems of coating difficulty and low wavelength sensitivity. The PCF has four layers of air holes, which dramatically reduces the optical fiber loss and is more conducive to the application of sensors in actual production. In addition, by introducing dual cores on the upper and lower sides of the central air hole, reducing the spacing between the core and the gold nanolayer, a stronger evanescent field can be generated in the cladding air hole. The optical fiber sensor can detect the refractive index of two samples simultaneously with a maximum sensitivity of 21300 nm/RIU. To the best of our knowledge, the sensitivity achieved in this work is the highest sensitivity with the dual sample synchronous detection sensors. The detection range of the refraction index is 1.35-1.41, and the resolution of the sensor is 4.695×10^-6. Overall, the sensor will be suitable for medical detection, organic chemical sensing, analyte detection, and other fields.     

基于包层模的光纤布拉格光栅折射率传感特性

提出了基于光纤布拉格光栅(FBG)包层模式的折射率传感方案。实验中,利用不同浓度的丙三醇水溶液作为外界折射率传感溶液,采用氢氟酸溶液化学腐蚀的方法来减小光纤包层的直径以增大包层模式对外界折射率的敏感度,研究了腐蚀后光纤布拉格光栅包层模式的耦合波长对外部折射率的变化关系。实验结果表明在1.3300~1.4584的折射率范围内,包层模式耦合波长随外界折射率增大而增大,在接近光纤包层折射率处具有很高的折射率灵敏度,最大达到了172 nm/riu(refractive index unit)。而且,包层模谐振的光谱半峰全宽(约0.07 nm)仅为布拉格纤芯模谐振光谱半峰全宽的1/4,能够获得更好的传感精度。     

重构多信道光纤光栅的改进离散层析算法

对重构多信道光纤光栅的离散层析算法进行了优化.在各信道加入相移的基础上,运用非线性最小二乘法对耦合系数进行高斯曲线拟合,降低了折射率调制深度的最大值且可以将剧烈变化的折射率调制深度平滑化.仿真表明,较之改进前的折射率调制最大值（0.001 3）,利用新算法在折射率调制最大值为0.000 5时成功设计了一个8信道光纤光栅,极大地降低了对光纤光敏性的要求.同时,折射率调制曲线的平滑化降低了光栅的实际刻写难度.     

基于少模-无芯-少模光纤结构的高灵敏度折射率传感器

光纤折射率传感器广泛应用于各种复杂环境的监测。设计了一种基于少模光纤（fewmode fiber,FMF）–无芯光纤（coreless fiber,CLF）–FMF结构的高灵敏度折射率传感器。该传感器由2小段FMF之间熔接1段减薄的CLF组成马赫-增德尔干涉仪（Mach–Zehnder interference,MZI）,测量外界折射率,利用光纤布拉格光栅（fiber Bragg grating,FBG）进行温度补偿。MZI干涉光谱中的谐振波谷同时受折射率和温度影响,FBG只受温度的影响。利用MZI和FBG的折射率和温度灵敏度系数构建灵敏度矩阵,实现折射率和温度的同步测量。实验结果表明,MZI折射率灵敏度为345.66 nm/RIU,温度灵敏度为0.013 4 nm/℃;FBG的温度灵敏度为0.010 4 nm/℃。     

基于空气孔微结构光纤的表面等离子体共振折射率传感器北大核心CSCD

提出了一种基于表面等离子体共振(SPR)效应增强的光子晶体光纤折射率传感器。该传感器结构通过光纤熔接机拼接光子晶体光纤(PCF),在光子晶体光纤中间引入一个空气孔形成PCF-空气孔-PCF的光纤传感结构,随后使用磁控溅射镀膜工艺在其表面沉积一层薄金膜制备而成。实验探究了折射率及温度对传感器的响应。结果表明,在1.333~1.389的折射率范围内,所提出的传感器的平均折射率灵敏度为2 142.52 nm,且测量线性度为0.981,品质因子约13.10。实验结果表明该传感器对温度不敏感。相比于无空气孔的PCF传感结构,引入的空气孔增强了SPR效应,使得传感器拥有良好的共振峰深度。得益于上述优势,该类型传感器有望在生物医学、环境监测等领域得到应用。     

不同包层直径的倾斜光纤光栅折射率传感特性

倾斜光纤光栅的透射谱中有纤芯模和大量的包层模,它们具有与布拉格光栅相同的温度特性.利用HF酸腐蚀的方法得到具有不同包层直径的倾斜光纤光栅,研究了其对外界折射率的传感特性.结果表明,外界环境折射率在1.333～1.4532之间变化时,同一直径倾斜光纤光栅的高阶包层模的敏感性要比低阶包层模强;随着包层直径的减小,包层模的敏感性增强,且在折射率比较高的环境中有更高的敏感性.因此,利用倾斜光纤光栅的温度特性不仅可以解决温度交叉敏感问题,而且通过小同的腐蚀程度能定制所需要的灵敏度,以实现对环境折射率的高灵敏度测量.该办法可应用于对生物和化学等高灵敏度传感领域的各种溶液进行实时监控.     

Three-hole microstructured optical fiber for efficient fiber Bragg grating refractometer

We present a photosensitive three-hole microstructured optical fiber specifically designed to improve the refractive index sensitivity of a standard fiber Bragg grating (FBG) sensor photowritten in the suspended Ge-doped silica core. We describe the specific photowriting procedure used to realize gratings in such a fiber. We then determine their spectral sensitivity to the refractive index changes of material filling the holes surrounding the core. The sensitivity is compared with that of standard FBGs photowritten in a six-hole fiber with a larger core diameter. We demonstrate an improvement in the sensitivity by two orders of magnitude and reach a resolution of 3 x 10(-5) and 6 x 10(-6) around mean refractive index values of 1.33 and 1.40, respectively.     

Polarization-dependent refractometer for discrimination of temperature and ambient refractive index

Transmission characteristics of polarization-dependent refractometer based on a surface long-period grating (SLPG) inscribed in a D-shaped photonic crystal fiber (PCF) are investigated. The birefringence of SLPG produces the separation of transmission spectra for TE and TM polarization modes. We also measure the sensitivities of PCF-based SLPG to temperature and external refractive index change depending on the input polarization states. The SLPG-based sensor exhibits different temperature and ambient index sensitivities corresponding to TE and TM polarization modes. Therefore, the SLPG inscribed in D-shaped PCFs can effectively discriminate temperature and ambient index sensitivities.