Cross-point analysis for a multimode fiber sensor based on surface plasmon resonance

A novel analysis based on surface plasmon resonance (SPR) with a side-polished multimode fiber and a white-light (halogen light) source is presented. The sensing system is a multimode optical fiber in which half of the core has been polished away and a 40 nm gold layer is deposited on to the polished surface by dc sputter. The SPR dip in the optical spectrum is investigated with an optical spectrum analyzer (OSA). In our SPR fiber sensor, the use of liquids with different refractive indices leads to a shift in the spectral dip in the SPR curve. The cross point (CP) of the two SPR spectra obtained from the refractive-index liquid and the deionized water measurements was observed with the OSA. The CP is shifted sensitively in wavelength from 630 to 1300 nm relative to a change in the refractive index of the liquid from 1.34 to 1.46. High sensitivities of 1.9 x 10(-6) refractive-index units (RIUs) in the range of the refractive index of the liquid from 1.40 to 1.44 of 5.7 x 10(-7) RIUs above the value of 1.44 are proposed and demonstrated in our novel SPR analysis.     

基于光纤气泡和纤芯失配的Mach-Zehnder干涉液体折射率传感器

介绍了一种基于光纤气泡和纤芯失配的Mach-Zehnder干涉液体折射率传感器. 将两根纤芯经过腐蚀的普通单模光纤熔接在一起, 在熔接点处形成一个气泡, 在距气泡20 mm处级联一段20 mm的细芯光纤, 再接入一段单模光纤, 形成单模光纤-气泡-单模光纤-细芯光纤-单模光纤结构的传感器. 气泡与光纤芯径失配处的两个节点起到光纤耦合器的作用, 从而形成光纤Mach-Zehnder干涉仪. 环境液体折射率的变化,将使得传感器透射谱能量发生变化, 通过测量干涉谱波峰峰值能量从而实现对折射率的测量. 并对所制作传感器的折射率响应特性进行了实验研究, 实验结果表明干涉谱波峰峰值能量与环境液体折射率之间存在良好的线性关系, 当环境液体折射率变化范围在1.351–1.402时, 响应灵敏度为143.537 dB/RIU, 线性度0.996. 该传感器在生物化学领域有较好的应用前景. 关键词： 光纤气泡 纤芯失配 Mach-Zehnder干涉仪 折射率传感     

Continuous-wave measurement of the fiber nonlinear refractive index

We propose a technique for measuring the nonlinear refractive index of fiber based on transmission-coefficient measurements in a fiber Sagnac interferometer. In contrast with traditional methods, the proposed method uses a single optical source operating in cw mode and direct intensity measurement, enabling one to avoid the errors caused by fiber dispersion and uncertainty of spectral peak difference measurements that occur with pulse-based methods. The nonlinear refractive index in 20-mol. % GeO(2) fiber was measured to be (3.1 +/- 0.2) x 10(-16) cm(2) W(-1) at 1064 nm.     

Microstructured fiber based plasmonic index sensor with optimized accuracy and calibration relation in large dynamic range

A novel surface plasmon resonance photonic sensor is proposed using an index-guided microstructured fiber with an analyte channel introduced into the central core. Compared with the previous designs of porous fiber core, variation of the signal amplitude with exterior refractive index is demonstrated to be contrary to that of the sensitivity in the proposed fiber, contributing to optimized detecting accuracy over a large refractive index range of 1.33 to 1.42. By carefully choosing the central channel size, the analyte-filled core can achieve narrower resonance spectral width and higher signal to noise ratio (SNR) than the air-filled core. Sensor responses are also studied in this paper based on two spectral interrogation methods, including monitoring single resonance shift and measuring change in the resonance separation. For both methods, response linearity has been improved considerably through partially filling the core with analyte. The maximal sensitivity reaches 10^− 6 refractive index unit (RIU). The linear sensing performance along with the broad measurement range is very promising in the application of the proposed sensor as sensitive refractometer.     

Ultrahigh sensitivity polarimetric strain sensor based upon D-shaped optical fiber and surface plasmon resonance technology

An ultrahigh sensitivity polarimetric strain sensor is proposed based upon a four-layer D-shaped optical fiber and surface plasmon resonance (SPR) technology. In contrast to existing SPR-based sensors, which are based on changes in the refractive index of the overlayer, the sensor proposed in this study is based on the change in the refractive index of the fiber core in response to the application of an axial load. Specifically, the phase difference between the P and S waves after passing through the sensor under SPR conditions is measured using a common-path heterodyne interferometer and is used to determine the corresponding change in the refractive index of the core, from which the strain is then inversely derived. The experimental results show that the sensitivity of the proposed sensor is around 2.19×10? deg/ε, i.e., degree/strain. By contrast, that of a conventional (non-SPR) polarimetric fiber sensor is just 5.2×102 deg/ε. To the best of the authors' knowledge, the sensor proposed in this study represents the first reported attempt to exploit the refractive index change of the core of an SPR-based fiber sensor for strain measurement purposes.     

侧边抛磨的U型金溅射塑料光纤等离子体共振传感器

为了测量溶液折射率变化，对塑料光纤纤芯表面的纤芯-金层-液体的3层膜结构进行研究，制作了一种使用U型结构并结合侧边抛磨方法的表面等离子体共振传感器。将截取的一段塑料光纤弯曲成为U型，并在烘箱中通过较高温度使这段光纤的曲率固定，对弯曲部分的外表面进行抛光，暴露该位置塑料光纤芯层并在其上溅射金纳米薄膜层，将制备好的传感器浸入不同折射率的液体中，使用光谱分析仪观察光谱的移动。实验结果表明:当塑料光纤SPR传感器测量折射率变化范围在1.333~1.406的液体时，可以通过光谱观察到随着液体折射率的增大，等离子体共振吸收峰位置也不断地向波长增大的方向移动，并且二者之间存在线性关系，其灵敏度为7.5×10-4 RIU/nm。该传感器探头具有灵敏度高、小型化、易制备、低成本的特点。     

Photonic crystal fiber tip interferometer for refractive index sensing

In this paper we present an interferometer based on photonic crystal fiber (PCF) tip ended with a solid silica-sphere for refractive index sensing. The sensor is fabricated by splicing one end of the holey PCF to a single mode fiber (SMF) and applying arc at the other end to form a solid sphere. The sensor has been experimentally tested for refractive index and temperature sensing by monitoring its wavelength shift. Measurement results show that the sensor has the resolution of the order of 8.7×10(-4) over the refractive index range of 1.33-1.40, and temperature sensitivity of the order of 10 pm/°C in the range of 20-100 °C.     

Highly sensitive refractometer with a photonic-crystal-fiber long-period grating

We present highly sensitive refractometers based on a long-period grating in a large-mode-area photonic crystal fiber (PCF). The maximum sensitivity is 1500 nm/refractive index unit at a refractive index of 1.33, to our knowledge the highest reported for any fiber grating. The minimal detectable index change is 2 x 10(-5). The high sensitivity is obtained by infiltrating the sample into the holes of the PCF to give a strong interaction between the sample and the probing field.     

Optical refractometer based on an asymmetrical twin-core fiber Michelson interferometer

We report and demonstrate an optical refractometer based on a compact fiber Michelson interferometer. The Michelson interferometer is composed of an asymmetrical twin-core fiber containing a central core and a side core. By chemically etching a segment of the twin-core fiber until the side core is exposed, the effective index of the side core in the etched region is sensitive to the environmental refractive index, which leads to a shift of the transmission spectrum of the Michelson interferometer. The experimental results show that such a device has a refractive index resolution of more than 800 nm/refractive index unit in the range of 1.34-1.37.     

基于无芯光纤的多参数测量传感器

设计并制作了一种基于单模-无芯-单模-无芯-单模光纤结构的马赫-曾德尔传感器,可用来同时测量折射率和温度.该传感器中,两处无芯光纤充当输入、输出耦合器,中间单模光纤作为传感臂.利用有限元仿真和理论分析,确定耦合器和传感臂的最优长度为15 mm.在无芯光纤中激发出的高阶模进入单模光纤的包层传输,由于倏逝场的作用,受到环境折射率和温度的影响.选取透射谱不同干涉级次的波谷作为研究对象,实现了折射率和温度的同步测量.实验结果表明:1545 nm附近干涉谷的折射率和温度灵敏度分别为–153.89 nm/RIU(refractive index unit)和0.166 nm/℃;1570 nm附近干涉谷的折射率和温度灵敏度分别为–202.74 nm/RIU和0.183 nm/℃.该传感器在实现折射率和温度同步测量的同时,仍能保持较高灵敏度,在生物医疗等方面有着较好的应用前景.     

Reflective fiber-optic refractometer based on a thin-core fiber tailored Bragg grating reflection

A novel reflective refractometer based on a thin-core fiber (TCF) sandwiched between a leading single-mode fiber (SMF) and a fiber Bragg grating (FBG) imprinted SMF stub was demonstrated. The reflection from the fiber stub occurs in two well-defined wavelength bands, corresponding to the Bragg core mode and cladding modes. The TCF section functions as a tailorable bridge between the FBG core mode reflection and the surrounding refractive index (SRI). Linear response with enhanced sensitivity of 133.26 dB/refractive index unit for temperature-immune SRI measurement within the biologically desirable sensing range of 1.33-1.41 has been achieved via cost-effective power detection.     

Optimization of photonic bandgap fiber long period grating refractive-index sensors

Long period gratings in low-index contrast solid-core photonic bandgap fibers are a promising platform for fiber-based fluid refractive index sensing with very low detection limits. We provide a comprehensive investigation of the possibilities for refractive index sensing using that principle in a commercial photonic crystal fiber filled with a fluid: using an acoustic grating, we map out the cladding bands, and use this data to optimize a long period grating’s sensitivity. We then implement the optimized long period grating, again using an acoustic grating, and directly measure its sensitivity to refractive index. We demonstrate a sensitivity of 17,900 nm/RIU (6.94 nm/°C) which corresponds to a smallest detectable index change of the fluid of 8.4 × 10⁻⁶.     

Resonant optical nonlinearity measurement of Yb(3+) / Al(3+) codoped optical fibers by use of a long-period fiber grating pair

A new method of measuring optical nonlinearity for resonant nonlinear optical fibers is proposed. A long-period fiber grating (LPG) pair was used to measure the nonlinear refractive index n(2) of a Yb(3+)/Al (3+) codoped optical fiber, which was spliced between the two LPGs, as the fiber was pumped with a laser diode. The nonlinear refractive index of the Yb(3+)/Al (3+) codoped fiber near 1580 nm depended on the pump power. As the pump power increased, the nonlinear refractive index decreased. At launched pump powers of 2-8 mW, the nonlinear refractive index of the Yb(3+)/Al (3+) codoped fiber near 1580 nm was ~7.5x10(-15)m (2)/W .     

Fiber refractometer based on a fiber Bragg grating and single-mode-multimode-single-mode fiber structure

A refractive index (RI) sensor based on a novel fiber structure that consists of a single-mode-multimode-single-mode (SMS) fiber structure followed by a fiber Bragg grating was demonstrated. The multimode fiber in the SMS structure excites cladding modes within output single-mode fiber (SMF) and recouple the reflected cladding Bragg wavelength to the input SMF core. By measuring the relative Bragg wavelength shift between core and cladding Bragg wavelengths, the RI can be determined. Experimentally we have achieved a maximum sensitivity of 7.33 nm/RIU (RI unit) at RI range from 1.324 to 1.439.     

Bragg光纤包层制作误差对导模特性的影响

对Bragg光纤中包层制造误差对导模特性的影响进行了深入的分析和研究,给出了一般N层波导中模式场标量波动方程求解的传输矩阵方法,并将其应用在Bragg光纤模式场的分析当中。分别研究了Bragg包层存在折射率误差和厚度误差时对光纤基模模式场的有效折射率、模场半径和芯区功率占比的影响,并利用统计的方法分析了不同制作误差时导模特性的相对变化。折射率误差在1‰的水平时,基模有效折射率、模场半径和芯区功率占比的方差水平为1.55×10~(-4)、1.04×10~(-1)和1.79×10~(-2);厚度误差在2%的水平时模式场参量的方差水平分别为3.61×10~(-5)、1.84×10~(-2)和2.35×10~(-3)。     

Single S-tapered fiber Mach-Zehnder interferometers

A fiber Mach-Zehnder interferometer (MZI) sensor, novel to our knowledge, based on a single "S"-like fiber taper has been fabricated via applying nonaxial pull in fiber tapering by a fusion splicer. The typical feature size of the structure has a length of 660 μm and the axial offset of 96 μm. This S fiber taper MZI has a refractive index (RI) sensitivity of 1590 nm/refractive index unit in the RI range of 1.409-1.425 and a strain sensitivity of about -60 pm/microstrain, which is 30 times higher than that of the normal two-taper-based MZI sensors.     

Precision measurement of the refractive index of air with frequency combs

We report an experimental method for high-precision refractive index measurement using a Michelson interferometer setup with a femtosecond optical frequency comb as the light source. We demonstrate this technique by measuring the refractive index of air, under different pressures, inside a 29 m multipass cell. Both spectral and temporal interferograms are recorded. The method has a sensitivity of 6.2 x 10(-9) and a standard error of 7.4 x 10(-8) at fixed parameters (pressure and temperature). The possible variation of the density factor from the Lorentz-Lorenz equation is also discussed.     

Fiber Optical Bragg Grating Refractometer

We have demonstrated an evanescent field refractive indexfiber sensor comprising a 42-mm Bragg grating in an etched fiber together with a tunable Distributed Bragg Reflector (DBR) laser. Characterization of different aqueous sucrose solutions resulted in a resolution of roughly 10 mM sucrose. The sensor in the presented form has a theoretical sensitivity of higher than 10 5 refractive index unit (riu) in a refractive index region close to the cladding index of the fiber. However, the technique allows for an even higher sensitivity than 10 6 riu with a proper signal processing scheme.     

Measurement of refractive-index variation with temperature by use of long-period fiber gratings

The thermo-optic coefficient of the core material of a fiber is analyzed by use of a pair of long-period fiber gratings. First the effective index difference between the core and the cladding modes is measured from the peaks of the interference fringe generated by the grating pair. The order of the cladding mode is decided by the cutoff wavelength and the numerical aperture of the fiber. The material index of the fiber core is obtained in terms of wavelength. At each wavelength the index is chosen to minimize the difference between the measured and the calculated spectra of the grating pair. Finally the thermo-optic coefficient of the fiber core is calculated by repetition of the measurement at different temperatures. With a germanosilicate-core fiber and a boron codoped germanosilicate-core fiber, the thermo-optic coefficients were 1.1x10(-5)/( degrees )C and 0.75x10(-5)/( degrees )C, respectively.     

Tunable phase-shifted fiber Bragg grating based on a microchannel fabricated by a femtosecond laser

A phase-shifted fiber Bragg grating(PS-FBG) based on a microchannel was proposed and realized by combining the pointby-point scanning method with chemical etching. The PS-FBG is composed of a fiber Bragg grating(FBG) and a microchannel through the fiber core. The microchannel can introduce phase shift into the FBG. What is more important is that it exposes the fiber core to the external environment. The phase shift peak is sensitive to the liquid refractive index, and it shows a linear refractive index response wavelength and intensity sensitivity of 2.526 nm/RIU and-111 d B/RIU, respectively.Therefore, such gratings can be used as sensors or tunable filters.