EQCM Study of Ru and RuO2 Surface Electrochemistry

The present study represents comparative analysis of voltammetric and microgravimetric behavior of active ruthenium (Ru), electrochemically passivated ruthenium (Ru/RuO₂) and thermally formed RuO₂ electrodes in the solutions of 0.5 M H₂SO₄ and 0.1 M KOH. It has been found that cycling the potential of active Ru electrode within E ranges 0 V–0.8 V and 0 V–1.2 V in 0.5 M H₂SO₄ and 0.1 M KOH solutions, respectively, leads to continuous electrode mass increase, while mass changes observed in alkaline medium are considerably smaller than those in acidic one. Microgravimetric response of active Ru electrode in 0.5 M H₂SO₄ within 0.2 V–0.8 V has revealed reversible character of anodic and cathodic processes. The experimentally found anodic mass gain and cathodic mass loss within 0.2–0.8 V make 2.2–2.7 g F^?1, instead of 17 g F^?1, which is the theoretically predicted value for Ru(OH)₃ formation according to equation: Ru+3H₂O?Ru(OH)₃+3H⁺+3e^?. In the case of Ru/RuO₂ electrode relatively small changes in mass have been found to accompany the anodic and cathodic processes within E range between 0.4 V and 1.2 V in the solution of 0.5 M H₂SO₄. Meanwhile cycling the potential of thermally formed RuO₂ electrode under the same conditions has lead to continuous decrease in electrode mass, which has been attributed to irreversible dehydration of RuO₂ layer. On the basis of microgravimetric and voltammetric study as well as the coulometric analysis of the results conclusions are presented regarding the nature of surface processes taking place on Ru and RuO₂ electrodes.     

An EC-FTIR study on the catalytic role of Pt in carbon corrosion

In this study, we investigate the role of Pt in the corrosion of carbon by Fourier-transformed infrared spectroscopy coupled in situ with electrochemical measurements. We confirm that the carbon corrosion rate is strongly enhanced in the presence of Pt and shed light on the reaction mechanisms at both anode and cathode potentials. It is shown that carbon surface oxide species (phenol, ether, carboxylic and carbonyl groups), formed at low electrode potential E < 0.60 V vs. RHE, spillover back from the carbon support to the Pt nanoparticles, where they are converted into CO and then slowly oxidized into CO₂. At higher electrode potential E > 0.60 V vs. RHE, oxygenated species resulting from water splitting on Pt facilitate the removal of these carbon surface oxides species yielding increased kinetics for carbon corrosion.     

EQCM Study of Iridium Anodic Oxidation in H2SO4 and KOH Solutions

In the present study anodic oxidation of iridium layer formed thermally on a gold‐sputtered quartz crystal electrode has been investigated by electrochemical quartz crystal microgravimetry (EQCM) in the solutions of 0.5 M H₂SO₄ and 0.1 M KOH. The emphasis here has been put on the microgravimetric behavior of iridium as a metal, because a few previous EQCM studies reported in literature have been devoted to iridium oxide films (IROFs). The objective pursued here has been to elucidate the nature of the main voltammetric peaks, which occur at different ranges of potential in the solutions investigated. It has been found that anodic oxidation of iridium electrode in 0.5 M H₂SO₄ and 0.1 M KOH solutions is accompanied by irregular fluctuations of the electrode mass at 0.4 V<E<0.8 V followed by regular increase in mass at 0.8 V<E<1.2 V. The cathodic process initially, at 1.2 V>E>0.9 V, proceeds without any or with slight increase in electrode mass, whereas at E<0.8 V a regular decrease in mass is observed. It has been found that mass to charge ratio characterizing the processes of interest is 2 to 3 g F^?1in acidic medium, whereas in the case of alkaline one it is 4 to 6 g F^?1. The main pair of peaks seen in the voltammograms of Ir electrode in alkaline medium at E<0.8 V is attributable to redox transition Ir(0)→Ir(III), whereas those observed in the case of acidic medium at E>0.8 V should be related to the redox process Ir(0)→Ir(IV) going via intermediate stage of Ir(III) formation. As a consequence of these redox transitions, the gel‐like surface layer consisting of Ir(III) or Ir(IV) hydrous oxides forms on the electrode surface.     

Influence of electrodeposition conditions on the properties of CdTe films

The results of the influence of electrodeposition conditions on the structural, compositional, optical, and photoelectrochemical properties of CdTe thin films deposited in one-step electrochemical method are presented. The CdTe films were prepared electrochemically from aqueous acidic solution with low ratios of Cd²⁺ ions to Te(IV) ions concentration. Instead of commonly used TeO₂, water-soluble Na₂TeO₃ was used as a source of tellurium ions. The cathodic deposition of CdTe was performed at different constant potentials from solutions containing different cadmium and tellurium ions concentration. As-deposited CdTe thin films were studied by different analytical techniques. The X-ray photoelectron spectroscopy spectra exhibited CdTe formation on the electrode with some amount of tellurium oxides and cadmium oxides. The best quality CdTe deposits, free of TeO₂, were formed in bath containing excess of Cd²⁺ ions and at the potential of ?0.65 V vs. saturated calomel electrode, slightly more positive than E _eq of Cd/Cd²⁺ system. Structural X-ray diffraction studies revealed polycrystallinity of deposits with the highest content of the (111)-oriented cubic (111) form. Optical band gap energy values were found in the range from 1.36 to 1.6 eV for CdTe films prepared at various synthesis conditions. The preliminary photoelectrochemical studies have shown that the variation of the deposition potential as well as bath composition leads to the formation of p- or n-type CdTe films. As-deposited CdTe films were not stable in polysulfide solution under illumination.     

A polynuclear mixed-valent ruthenium oxide/cyanoruthenate composite that yields thin coatings on a glassy carbon electrode with high catalytic activity toward methanol oxidation

Polynuclear ruthenium oxide/cyanoruthenate films on carbon substrates were grown by cycling the potential between 0.5 and 1.0 V (vs SCE) for 5–90 min in fresh 2 mM RuCl₃·3 H₂O, 2 mM K₄Ru(CN)₆·3 H₂O, 0.5 M KCl solution at pH 2. During the positive scans, the cationic Ru(III,IV)-oxo polynuclear species interacted with the simultaneously formed anionic CN-bridged Ru dimers to yield sparingly soluble deposits on the electrode surfaces. Different thicknesses, typically corresponding to 2–50×10⁻¹⁰ mol cm⁻², could be obtained by varying the cycling times. The absorption spectra of the coatings obtained at SnO₂-covered glass electrodes were different from those known for RuO₂ films and exhibited two absorption bands at about 400 and 700 nm. IR spectroscopic measurements confirmed the presence of a CN group in the deposit, as well as showing significant aquation of the entire coating. Ru, O, N and K (from KCl) were detected by means of Auger electron spectroscopy. The surface electrochemistry and stability of the film were significantly enhanced in K⁺-containing supporting electrolytes. The system provides a durable catalytic surface which allows the voltammetric oxidation of methanol; in 0.5 M H₂SO₄+0.5 M K₂SO₄ electrolyte the resulting anodic peak is at 1.01 V (vs. SCE). Electrooxidation was not possible at bare carbon electrodes, at least before the onset of the electrolyte decomposition.     

Surface and Subsurface Oxygen on Platinum in a Copper Perchlorate Solution

The formation of an adatom layer on polycrystalline platinum and the three-dimensional nucleation of copper in a copper perchlorate solution are studied by cyclic voltammetry at 0.1 V s^–1 while varying potential ranges and by recording potentiostatic current transients. About 0.6 monolayers of copper adatoms are deposited when cycling with anodic limit E _a = 1.35 V, the process is slower than that in an acid sulfate solution. Decreasing E _a accelerates the process (nearly one monolayer forms for E _a = 0.80–0.95 V in a cathodic scan) due to an increased number of active centers (metastable copper oxides) and, probably, to a change in the platinum surface microstructure. Oxygen for copper oxides is presumably supplied by water molecules adsorbed on a monolayer of copper adsorbed atoms and by subsurface oxygen (O_ss), which appears on the platinum surface after the destruction of complexes O_ss–Pt _n –ClO₄. Both the copper nucleation and the deposit growth accelerate at higher concentrations of copper oxides, which form at low E _a. High cathodic overvoltages decrease the number of active crystallization centers due to reduction or removal of copper oxides.     

Electrochemical Properties of Overoxidized Poly-3,4-Ethylenedioxythiophene

The properties of poly(3,4-ethylenedioxythiophene) (PEDOT) films were studied electrochemically at high positive potentials (from–0.3 to 1.5 V relative to the Ag/AgCl electrode). A cyclic voltammetry (CV) study revealed the range of potentials (up to 1.3–1.5 V) where the cycling leads to significant changes in the electrochemical, structural, and morphological properties of the polymer film due to overoxidation. When the upper cycling potential E_up exceeded 1.4 V, the anodic current significantly increased during the first cycle and then decreased, which suggests a loss of the electroactivity of the polymer and degradation of its properties. In the high-frequency region of the impedance spectra of the PEDOT films, a semicircle appears after overoxidation, which indicates a notable increase of the charge transfer resistance in the system, in contrast to the films subjected to potentiodymanic processing in a limited range of potentials from–0.3 to 1.3 V. The effect of overoxidation on the polymer morphology was studied by scanning electron microscopy. The chemical state of elements in the structure of the polymer film was determined by X-ray photoelectron spectroscopy. The obtained data indicate that–S=O groups formed at the thiophene sulfur in the polymer.

     

Realization of Rhodium Metal‐Oxide Electrode in Indifferent Electrolytes

The pH‐dependence of the stationary open‐circuit potential E_i=0^st of rhodium electrode with a surface layer of anodically formed insoluble compounds has been studied in sulfate and phosphate solutions by means of cyclic voltammetry and chronopotentiometry. The range of potentials of the investigations performed has been confined to the region of rhodium electrochemical oxidation/reduction, i.e., 0.2<E<1.2 V (RHE) in order to prevent any possible interference of other reactions such as H₂ and O₂ evolution. It has been shown that rhodium electrode with a layer of surface compounds formed anodically at E<<1.23 V (RHE) behaves like a reversible metal‐oxide electrode within the range of pH values from ca. 1.0 to ca. 8.0. It has been presumed that the stationary potential of such electrode is determined by the equilibrium of the following electrochemical reaction: Rh+3H₂O??Rh(OH)₃+3H⁺+3e^?. The pH‐dependence of the reversible potential of Eequation/tex2gif-inf-6.gif electrode has been found to be: Eequation/tex2gif-inf-8.gif=E_i=0^st=0.69?0.059 pH, V. In acid solutions (pH<2.0) rhodium hydroxide dissolves into the electrolyte, therefore, to reach equilibrium, the solution must be saturated with Rh(OH)₃. This has been achieved by adding Rh³⁺ ions in the form of Rh₂(SO₄)₃. The solubility product of Rh(OH)₃, estimated from the experimental Eequation/tex2gif-inf-16.gif?pH dependence obtained, is ca. 1.0×10^?48, which is close to the value given in literature.     

Chemical and electrochemical behavior of metallic technetium in acidic media

The chemical and electrochemical properties of technetium metal were studied in 1–6 M HX and in 1 M NaX (pH 1 and 2.5), X = Cl, NO₃. The chemical dissolution rates of Tc metal were higher in HNO₃ than in HCl (i.e. 8.63 × 10^?5 mol cm^?2 h^?1 in 6 M HNO₃ versus 2.05 × 10^?9 mol cm^?2 h^?1 in 6 M HCl). The electrochemical dissolution rates in HNO₃ and HCl were similar and mainly depended on the electrochemical potential and the acid concentration. The optimum dissolution of Tc metal was obtained in 1 M HNO₃ at 1 V/AgAgCl (1.70 × 10^?3 mol cm^?2 h^?1). The dissolution potentials of Tc metal in nitric acid were in the range of 0.596–0.832 V/AgAgCl. Comparison of Tc behavior with Mo and Ru indicated that in HNO₃, the dissolution rate followed the order: Mo > Tc > Ru, and for dissolution potential the order: E _diss(Ru) > E _diss(Tc) > E _diss(Mo). The corrosion products of Tc metal were analyzed in HCl solution by UV–Visible spectroscopy and showed the presence of TcO₄ ^?. The surface of the electrode was characterized by microscopic techniques; it indicated that Tc metal preferentially corroded at the scratches formed during the polishing and no oxide layer was observed.     

Ein neues ternäres Rubidium-Eisen Oxid Darstellung von Rb6Fe2O6

A New Rubidium-Iron Ternary Oxide. Preparation of Rb₆Fe₂O₆ Dark red crystals, formed by the heating of mixtures of rubidium and iron oxides at 773 K, were identified as the new ternary oxide Rb₆Fe₂O₆ by means of chemical analysis and X-ray powder diffraction analysis. X-ray powder diffraction data and free energy of formation data are presented, the latter having been determined by equilibrium oxygen potential measurements in liquid rubidium using a Harwell electrochemical oxygen meter.     

Solvent directed templated synthesis of mono- and di(Schiff base) complexes of Ni(II)

The mono- and binuclear complexes Ni(Salen) (I) and Ni₂(Salen)₂ (II) (H₂Salen = N,N′-bis(salicylidene)ethane-1,2-diamine), have been synthesized and structurally characterized by single-crystal X-ray diffraction studies. The X-ray structural analyses show that the metal center of complex I is mononuclear and tetracoordinate with a distorted tetrahedron, whereas the metal-centered complex II is binuclear and pentacoordinate with rectangular pyramid geometries, respectively. The electrochemical studies evidenced for the mononuclear Ni(II) complex shows one quasireversible reduction potential at −0.80 V (E _pc ) and the binuclear Ni(II) complex shows a reduction potential at −0.90 V (E _pc ) in the cathodic region. The article is published in the original.     

Structural and electronic properties of HfO2 films on Si through H2O2 wet oxidation with improved thermal stability

The thermal stability and material properties of HfO₂ thin films on Si substrates with and without H₂O₂ wet chemical oxidation were investigated. The HfO₂ samples were deposited through plasma-enhanced atomic layer deposition and subjected to thermal annealing. They were then examined using X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, reflection electron energy loss spectroscopy, and conductive atomic force microscopy. For the Si substrate without H₂O₂ wet chemical oxidation, a native oxide (~1.8 nm) was formed on the substrate before HfO₂ deposition. After the annealing process at 600°C, the band gap (E_g) of the HfO₂ films increased from 6.0 to 6.2 eV due to the diffusion of Si into HfO₂. Furthermore, the conduction and valence band offsets (ΔE_c and ΔE_v, respectively) between HfO₂ and Si changed from 1.02 to 1.42 and 3.86 to 3.66 eV, respectively. After the H₂O₂ wet oxidation of the Si substrate, a 1.5-nm chemical oxide was formed instead of a native oxide. The band offset and E_g values of HfO₂ were similar before and after 600°C annealing (ΔE_v = 3.86 eV, ΔE_c = 1.02 eV, and E_g = 6.0 eV), implying the high thermal stability of the HfO₂ films. Accordingly, wet oxidation not only prevents diffusion from chemical oxide but also markedly improves the oxide leakage current, which is useful for developing highly efficient and thermally stable HfO₂ gate oxides in Si-based integrated circuit devices.     

Electrochemical instabilities due to pitting corrosion of iron

Electrochemical instabilities induced by chlorides and bromides due to pitting corrosion of iron in sulfuric acid solutions are investigated. Analysis of the electrochemical instabilities as a function of the applied potential and the nature and concentration of the aggressive chemical species shows that the system exhibits a transition from aperiodic bursting of large-amplitude to small-amplitude chaotic oscillations at a critical potential (bifurcation potential, E _bif). The E _bif is determined by the halide concentration inside the pits and coincides with the repassivation potential defined in corrosion studies to explain pit repassivation due to changes in pit chemistry. Surface observations show that, at E < E _bif, an active-passive state dissolution (etching) occurs, while at E > E _bif, a polishing state dissolution is reached. Spatial interactions between early initiated pits and the adjacent electrode surface, oxide film alteration, aggressive species accumulation around active pits, and formation of ferrous salt layers in front of the Fe electrode are all considered to be associated with electrochemical instabilities emerging during pitting corrosion of iron under different dissolution states. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 5, pp. 535–550. The text was submitted by the authors in English.     

Initial corrosion behavior of composite coatings obtained by co-electrodeposition of zinc with nanoparticles of Ti and Ce oxides

The present work reports the results obtained for the electrodeposition of composite Zn coatings on steel by using Ti and Ce oxides nanopowders, separately or in mixture, and a TiO₂·CeO₂ binary oxide. In an attempt to correlate the effects of nanoparticles on corrosion behavior of the composite deposits, the properties of Zn–TiO₂·CeO₂ layers were compared with those referring to similar coatings prepared by using a simple mixture of the two oxides or individual oxides. Corrosion measurements were performed in 0.2 g?L^?1 Na₂SO₄ solution (pH?=?5). The results of electrochemical measurements (open circuit potential measurements, polarization curves, and electrochemical impedance spectroscopy) were corroborated with those obtained by using X-ray diffraction, atomic force microscopy, scanning electron microscopy, and salt spray tests. The results indicate that the composite Zn–(TiO₂?+?CeO₂) coatings exhibit the highest corrosion resistance from all investigated Zn coatings.     

Blue Osmium(IV) Sulfite Complex: Synthesis and Study

Blue osmium(IV) sulfite complex Na₄[Os₂(-O)₂(SO₃)₄(H₂O)₄] · 4.5 H₂O was synthesized via the reaction of aqueous solutions containing OsO₄ and equimolar amount of Na₂SO₃ and H₂SO₄ at 50°C and its composition and structure were determined by elemental analysis, X-ray electronic and IR spectroscopies, and thermogravimetric analysis. The compound is X-ray amorphous, insoluble in water but soluble in hydrochloric and sulfuric acids. The electrochemical methods (cyclic voltammetry and potential-controlled coulometry) indicate the complex polymerization in solutions. Under continuous electrolysis at high negative potentials (E _r = –0.10 V), the product under study is depolymerized and the monomeric Os(II) complexes are formed. At a high positive potential (E ₀ = 1.00 V), Os(VI) is formed that disproportionates into Os(IV) and Os(VIII).     

Porous Nitrogen‐doped Reduced Graphene Oxide Gels as Efficient Supercapacitor Electrodes and Oxygen Reduction Reaction Electrocatalysts

Heteroatom‐doped carbon materials have been widely used in energy storage and conversion such as supercapacitors and electrocatalysts. In this work, L‐asparagine (Asn), an amino acid derivative, has been used as a doping agent to prepare nitrogen‐ doped reduced graphene oxide gels (N‐GAs). The 3D interconnected structure gives rise to the superior electrochemical properties for supercapacitor and electrocatalytic oxygen reduction reaction (ORR). The N‐GA‐4 (the mass ratio of Asn to graphene oxide (GO) is 4 : 1 by hydrothermal method) electrode shows the capacitance of 291.6 F·g^–1 at 0.5 A·g^–1. Meanwhile, the assembled symmetric supercapacitor achieves a maximum energy density of 23.8 Wh· kg^–1 when the power density is 451.2 W·kg^–1, and demonstrates an ultralong cycling life that the retention of capacitance is 99.3% after 80000 cycles. What's more, the annealed aerogel N‐GA‐4‐900 exhibits an onset potential (E_onset) of 0.95 V, half wave potential (E_1/2) of 0.84 V (vs. RHE) and the oxygen reduction current density of 5.5 mA·cm^–2 at 0.1 V with nearly four‐electron transfer, which are superior to commercial Pt/C. This work offers a new insight into the synthesis and applications of N‐GAs materials towards high performance in supercapacitors and ORR.     

Electrochemistry of microparticles of tris (2,2′-bipyridine) ruthenium(II) hexafluorophosphate

The electrochemical behaviour of tris(2,2′-bipyridine)ruthenium(II) hexafluorophosphate (Ru(II)) microparticles, immobilised on a graphite electrode and adjacent to an aqueous electrolyte solution, has been studied by cyclic voltammetry and an in situ spectroelectrochemical technique. The solid Ru(II) complex exhibits one reversible redox couple with a formal potential (E_f) of 1.1 V versus Ag¦AgCl. The continuous cyclic voltammetric experiments showed that the Ru(II) microparticles are stable during the electrochemical conversions. The in situ spectroelectrochemical study showed that the absorbance at 463 nm decreased due to the oxidation of Ru(II) to Ru(III). Upon reduction, the growth of absorbance at 463 nm was observed due to the formation of Ru(II) complex and this process was reversible.     

The electrochemical behaviour of butyltrimethylammonium bis(trifluoromethylsulfonyl)imide at negatively polarised aluminium electrode studied by in situ soft X-ray photoelectron spectroscopy,electrochemical impedance spectroscopy and cyclic voltammetry techniques

The in situ X-ray photoelectron spectroscopy data indicate that butyltrimethylammonium bis(trifluoromethylsulfonyl)imide (N4111(TFSI)) adsorbs strongly within the potential range −3.25 V < E < −2.25 V and specifically at E < −3.25 V (vs. Ag-QRE) at the Al electrode. Strong adsorption of the intermediates of N4111(TFSI) electrochemical decomposition was observed in electrochemical impedance spectroscopy and cyclic voltammetry measurements. At E < −4.25 V (vs. Ag-QRE), very intensive electrochemical reduction of N4111(TFSI) took place at the Al electrode giving gaseous products. In the potential range from − 2.25 to 0.00 V (vs. Ag-QRE), non-specific adsorption of N4111(TFSI) exists et al. surface.

     

Theoretical and Experimental Investigation of Functionalized Cyanopyridines Yield an Anolyte with an Extremely Low Reduction Potential for Nonaqueous Redox Flow Batteries

Cyanopyridines and cyanophenylpyridines were investigated as anolytes for nonaqueous redox flow batteries (RFBs). The three isomers of cyanopyridine are reduced at potentials of −2.2 V or lower vs. ferrocene^+/0 (Fc^+/0), but the 3-CNPy⋅⁻ radical anion forms a sigma-dimer that is re-oxidized at E≈−1.1 V, which would lead to poor voltaic efficiency in a RFB. Bulk electrochemical charge-discharge cycling of the cyanopyridines in acetonitrile and 0.50 M [NBu₄][PF₆] shows that 2-CNPy and 4-CNPy lose capacity quickly under these conditions, due to irreversible chemical reaction/decomposition of the radical anions. Density-functional theory (DFT) calculations indicated that adding a phenyl group to the cyanopyridines would, for some isomers, limit dimerization and improve the stability of the radical anions, while shifting their E_1/2 only about +0.10 V relative to the parent cyanopyridines. Among the cyanophenylpyridines, 3-CN-6-PhPy and 3-CN-4-PhPy are the most promising as anolytes. They exhibit reversible reductions at E_1/2=−2.19 and −2.22 V vs. ferrocene^+/0, respectively, and retain about half of their capacity after 30 bulk charge-discharge cycles. An improved version of 3-CN-6-PhPy with three methyl groups (3-cyano-4-methyl-6-(3,5-dimethylphenyl)pyridine) has an extremely low reduction potential of −2.50 V vs. Fc^+/0 (the lowest reported for a nonaqueous RFB anolyte) and loses only 0.21 % of capacity per cycle during charge-discharge cycling in acetonitrile.     

Surface and Subsurface Oxygen on Platinum in a 0.5 M H2SO4 + 0.01 M CuSO4 Solution

The formation of a copper adatom layer on polycrystalline platinum in a copper sulfate solution is studied by cyclic voltammetry in different cycling ranges at 0.1 V s^–1. The copper adatom deposition kinetics is controlled by the following factors. The substrate's top layer structure during the oxygen exit onto the surface may be unstable at anodic limits E _a = 0.90–1.35 V. The concentration of copper oxides (active centers) may be higher at E _a = 0.8–0.95 V. The balance between different adsorption sites differs in different cycling conditions. Of importance is the number of complexes O_ss–Pt _n –SO₄ and O_ss–Pt _n –O_c, where O_ss is subsurface oxygen and O_c is chemisorbed oxygen.