Direct determination of benzo[a]pyrene in water samples by a gold nanoparticle-based solid phase extraction method and laser-excited time-resolved Shpol'skii spectrometry

The strong affinity between polycyclic aromatic hydrocarbons (PAH) and the surface of gold colloids is investigated to device an extraction method for water samples. Within the 20-100 nm particle diameter range, the 20 nm gold nanoparticles showed the best extraction efficiencies for all the studied analytes. The new approach is combined to laser-excited time-resolved Shpol'skii spectrometry for the direct analysis of benzo[a]pyrene in drinking water samples. For a 500 μL sample volume, the analytical figures of merit demonstrate precise and accurate analysis at the parts-per-trillion level. The extraction efficiencies are statistically equivalent to 100% with relative standard deviations lower than 2%. The average recoveries were varied from 87.5% to 96.5% for different concentration of analytes. The simplicity of the experimental procedure, the low analysis cost, and the excellent analytical figures of merit demonstrate the potential of this approach for routine analysis of drinking water samples.     

Chemometrics-assisted excitation–emission fluorescence spectroscopy on nylon-attached rotating disks. Simultaneous determination of polycyclic aromatic hydrocarbons in the presence of interferences

This work presents a green and very simple approach which enables the accurate and simultaneous determination of benzo[a]pyrene, dibenz[a,h]anthracene, benz[a]anthracene, and chrysene, concerned and potentially carcinogenic heavy-polycyclic aromatic hydrocarbons (PAHs) in interfering samples. The compounds are extracted from water samples onto a device composed of a small rotating Teflon disk, with a nylon membrane attached to one of its surfaces. After extraction, the nylon membrane containing the concentrated analytes is separated from the Teflon disk, and fluorescence excitation–emission matrices are directly measured on the nylon surface, and processed by applying parallel factor analysis (PARAFAC), without the necessity of a desorption step. Under optimum conditions and for a sample volume of 25 mL, the PAHs extraction was carried out in 20 min. Detection limits based on the IUPAC recommended criterion and relative errors of prediction were in the ranges 20–100 ng L⁻¹ and 5–7%, respectively. Thanks to the combination of the ability of nylon to strongly retain PAHs, the easy rotating disk extraction approach, and the selectivity of second-order calibration, which greatly simplifies sample treatment avoiding the use of toxic solvents, the developed method follows most green analytical chemistry principles.     

A new strategy based on cholesterol-functionalized iron oxide magnetic nanoparticles for determination of polycyclic aromatic hydrocarbons by high-performance liquid chromatography with cholesterol column

This study reported for the first time the use of cholesterol-functionalized magnetic nanoparticles (Fe₃O₄@SiO₂@Chol) for the determination of polycyclic aromatic hydrocarbons (PAHs) in traditional Chinese medicine samples (TCMs) by high performance liquid chromatography (HPLC) coupled with fluorescence detection. The method was efficient, environmentally friendly, and fast. The solvent consumption of the proposed column is only half of the conventional column but with higher efficiency. Influencing factors, including sorbent amount, desorption solvent, sample volume and extraction time, were investigated in detail. Under the optimum conditions, good linearity (R² > 0.991) was obtained over the range of 5–400 ng g⁻¹, with limits of detection (LOD) 0.75, 0.50, 1.0, 0.56, 0.60, 0.84 and 0.80 ng g⁻¹ for anthracene, fluoranthene, pyrene, chrysene, benzo[a]anthracene, benzo(b)fluoranthene and benzo(k)fluoranthene, respectively.     

Using gold nanoparticles to improve the recovery and the limits of detection for the analysis of monohydroxy-polycyclic aromatic hydrocarbons in urine samples

We present a novel approach to improve the analytical figures of merit of solid-phase extraction high-performance liquid chromatography (SPE-HPLC) for the analysis of monohydroxy-polycyclic aromatic hydrocarbons in urine samples. The novel alternative substitutes the evaporation step that is currently used in SPE-HPLC methodology with a pre-concentration procedure that extracts metabolites with gold nanoparticles. The analytical potential of the new approach is evaluated with the following six metabolites: 9-hydroxyphenanthrene, 2-hydroxyfluorene, 1-hydroxypyrene, 6-hydroxychrysene, 3-hydroxybenzo[a]pyrene and 4-hydroxybenzo[a]pyrene. We demonstrate that the substitution of the evaporation step with the gold nanoparticles procedure improves the overall recoveries, the relative standard deviations of the average recoveries and the limits of detection of SPE-HPLC analysis. The overall recoveries of the studied metabolites varied from 59.7 ± 3.6% (2-hydroxyfluorene) to 92.3 ± 2.5% (6-hydroxychrysene). The relative standard deviations of the average recoveries were lower than 6%. The limits of detection were at the parts-per-trillion levels and varied from ∼2 pg mL⁻¹ (6-hydroxychrysene) to ∼18 pg mL⁻¹ (2-hydroxyfluorene).     

Ultrasonication extraction and gel permeation chromatography clean-up for the determination of polycyclic aromatic hydrocarbons in edible oil by an isotope dilution gas chromatography–mass spectrometry

An analytical method for the determination of US EPA priority pollutant 16 polycyclic aromatic hydrocarbons (PAHs) in edible oil was developed by an isotope dilution gas chromatography–mass spectrometry (GC–MS). Extraction was performed with ultrasonication mode using acetonitrile as solvent, and subsequent clean-up was applied using narrow gel permeation chromatographic column. Three deuterated PAHs surrogate standards were used as internal standards for quantification and analytical quality control. The limits of quantification (LOQs) were globally below 0.5 ng/g, the recoveries were in the range of 81–96%, and the relative standard deviations (RSDs) were lower than 20%. Further trueness assessment of the method was also verified through participation in international cocoa butter proficiency test (T0638) organised by the FAPAS with excellent results in 2008. The results obtained with the described method were satisfying (z ≤ 2). The method has been applied to determine PAH in real edible oil samples.     

Development of a sample preparation procedure of sewage sludge samples for the determination of polycyclic aromatic hydrocarbons based on selective pressurized liquid extraction

An automated, simple and sensitive method based on selective pressurized liquid extraction (SPLE) was developed for the analysis of polycyclic aromatic hydrocarbons in sewage sludge samples. The new sample preparation procedure consists of on-line clean-up by inclusion of sorbents in the extraction cell, and combines elevated temperatures and pressures with liquid solvents to achieve fast and efficient removal of target analytes from complex sewage sludge matrices. The effects of various operational parameters (e.g. sample pretreatment, extraction solvent, temperature, pressure, static time, etc.) on the performance of SPLE procedure were carefully investigated, obtaining the best results when SPLE conditions were fixed at 140 °C, 1500 psi, static time of 5 min and n-hexane as extraction solvent. A new programmed temperature vaporization–gas chromatography–tandem mass spectrometry method based on large volume injection (PTV–LVI–GC–MS/MS) was also developed and analytical determinations were performed by high performance liquid chromatography coupled with fluorescence detection and GC–MS/MS. The extraction yields for the different compounds obtained by SPLE ranged from 84.8% to 106.6%. Quantification limits obtained for all of these studied compounds (between 0.0001 and 0.005 μg g⁻¹, dry mass) were well below the regulatory limits for all compounds considered. To test the accuracy of the SPLE technique, the optimized methodology was applied to the analysis of a certified reference material (sewage sludge (BCR088)) and a reference material (sewage sludge (RTC-CNS312-04)), with excellent results.     

Multi-way partial least-squares and residual bi-linearization for the direct determination of monohydroxy-polycyclic aromatic hydrocarbons on octadecyl membranes via room-temperature fluorescence excitation emission matrices

Multi-way partial least-squares (N-PLS) is combined to the residual bi-linearization procedure (RBL) for the direct analysis of metabolites of polycyclic aromatic hydrocarbons in urine samples. Metabolite analysis is carried out via a two-step experimental procedure based on solid-phase extraction and room temperature fluorescence spectroscopy. Excitation-emission matrices are recorded from octadecyl (C18) membranes that serve as solid substrates for sample extraction and spectroscopic measurements. Excellent metabolite recoveries were obtained in all cases, which varied from 96.2 ± 1.35% (9-hydroxyphenanthrene) to 99.7 ± 0.49% (3-hydroxybenzo[a]pyrene). Background correction of extraction membranes is carried out with a new alternating least-squares (ALS) procedure adapted to second order data. The performance of N-PLS/RBL is compared to the well-established multivariate curve resolution-alternating least-squares (MCR-ALS) algorithm. Both algorithms provided similar analytical figures of merit, including their ability to handle unknown interference in urine samples. With only 10 mL of sample, the limits of detection varied between 0.06–0.08 ng mL⁻¹ (1-hydroxypyrene) and 0.016–0.018 ng mL⁻¹ (2-hydroxyfluorene). When compared to previously reported univariate calibration data, the limits of detection via N-PLS/RBL and MCR-ALS are approximately one order of magnitude higher. This was somehow expected due to the effect of unexpected components in multivariate figures of merit, i.e. a more realistic approach to the analysis of metabolites in human urine samples.     

Carbon nanospheres as solid‐phase microextraction coating for the extraction of polycyclic aromatic hydrocarbons from water and soil samples

A solid‐phase microextraction with carbon nanospheres coated fiber coupled with gas chromatographic detection was established for the determination of eight polycyclic aromatic hydrocarbons (naphthalene, biphenyl, acenaphthene, fluorine, phenanthrene, anthracene, fluoranthene, and pyrene) in water and soil samples. The experimental parameters (extraction temperature, extraction time, stirring rate, headspace volume, salt content, and desorption temperature) which affect the extraction efficiency were studied. Under the optimized conditions, good linearity between the peak areas and the concentrations of the analytes was achieved in the concentration range of 0.5‐300 ng/mL for water samples, and in the concentration range of 6.0‐2700 ng/g for soil samples. The detection limits for the analytes were in the range of 0.12‐0.45 ng/mL for water samples, and in the range of 1.53‐2.70 ng/g for soil samples. The method recoveries of the polycyclic aromatic hydrocarbons for spiked water samples were 80.10‐120.1% with relative standard deviations less than 13.9%. The method recoveries of the analytes for spiked soil samples were 80.40‐119.6% with relative standard deviations less than 14.4%. The fiber was reused over 100 times without a significant loss of extraction efficiency.     

Room-temperature fluorescence spectroscopy of monohydroxy metabolites of polycyclic aromatic hydrocarbons on octadecyl extraction membranes

Urine analysis of monohydroxy metabolites is recognized as an accurate assessment of human exposure to polycyclic aromatic hydrocarbons. Despite the sophisticated arsenal of analytical tools, monitoring of monohydroxy metabolites via simple, cost effective and direct methods of analysis still remains a challenge. This article evaluates the analytical potential of solid-phase extraction room-temperature fluorescence spectroscopy for the problem at hand. Extraction membranes serve the dual purpose of sample pre-concentration and solid substrate for RTF measurements. The potential of our proposition is demonstrated with the analysis of 2-hydroxy-fluorene, 1-hydroxy-pyrene, 3-hydroxy-benzo[a]pyrene and 9-hydroxy-phenanthrene in synthetic urine samples. Signal reproducibility is improved with the aid of a sample holder specifically designed for the manual optimization of luminescence signals. Background correction of solid substrates is carried out with the aid of Asymmetric Least Squares. Recovery values for the studied metabolites varied from 99.0 ± 1.2% (3-hydroxy-benzo[a]pyrene) to 99.9 ± 0.05% (1-hydroxy-pyrene). With only 10 mL of urine sample, the limits of detection varied from 57 pg mL⁻¹ (2-hydroxy-fluorene) to 2 pg mL⁻¹ (1-hydroxy-pyrene). Additional figures of merit include a simple experimental procedure for routine screening of numerous samples and compatibility with portable instrumentation for field analysis. Because of the non-destructive nature of fluorescence measurements, membranes can be brought to the lab for subsequent elution and confirmation of compounds via high-resolution techniques.     

Application of copolymer coated frits for solid-phase extraction of poly cyclic aromatic hydrocarbons in water samples

A conducting copolymer of pyrrole and phenol was electrochemically synthesized on steel frits as a sorbent. The applicability of the frit was assessed for the solid-phase extraction of trace amounts of polycyclic aromatic hydrocarbons (PAHs) in aqueous samples followed by HPLC–UV. The coating produced was very adherent and the scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and FTIR spectrum for the coated frit were studied. The effects of various parameters on the efficiency of the solid-phase extraction process, such as the sample loading rate, elution solvent type, salt effect, volume and flow rate of sample and elution solvent were investigated. Under the optimal conditions, the calibration curves were obtained in the range of 0.1–500 ng mL⁻¹ (r² > 0.98) and the LODs (S/N = 3) were obtained in the range of 0.01–0.08 ng mL⁻¹. Relative standard deviations (RSDs) for intra- and inter-day precision were 2.7–10.2% and 3.6–11.4%, respectively. The recoveries (8 and 40 ng mL⁻¹) ranged from 79% to 115%. The simplicity of experimental procedure, short sample analysis, high extraction efficiency, and the use of low-cost adsorbent show the potential of this method for routine analysis of PAHs in real samples.     

Determination of polycyclic aromatic hydrocarbons in food samples by automated on-line in-tube solid-phase microextraction coupled with high-performance liquid chromatography-fluorescence detection

A simple and sensitive automated method, consisting of in-tube solid-phase microextraction (SPME) coupled with high-performance liquid chromatography-fluorescence detection (HPLC-FLD), was developed for the determination of 15 polycyclic aromatic hydrocarbons (PAHs) in food samples. PAHs were separated within 15 min by HPLC using a Zorbax Eclipse PAH column with a water/acetonitrile gradient elution program as the mobile phase. The optimum in-tube SPME conditions were 20 draw/eject cycles of 40 μL of sample using a CP-Sil 19CB capillary column as an extraction device. Low- and high-molecular weight PAHs were extracted effectively onto the capillary coating from 5% and 30% methanol solutions, respectively. The extracted PAHs were readily desorbed from the capillary by passage of the mobile phase, and no carryover was observed. Using the in-tube SPME HPLC-FLD method, good linearity of the calibration curve (r > 0.9972) was obtained in the concentration range of 0.05–2.0 ng/mL, and the detection limits (S/N = 3) of PAHs were 0.32–4.63 pg/mL. The in-tube SPME method showed 18–47 fold higher sensitivity than the direct injection method. The intra-day and inter-day precision (relative standard deviations) for a 1 ng/mL PAH mixture were below 5.1% and 7.6% (n = 5), respectively. This method was applied successfully to the analysis of tea products and dried food samples without interference peaks, and the recoveries of PAHs spiked into the tea samples were >70%. Low-molecular weight PAHs such as naphthalene and pyrene were detected in many foods, and carcinogenic benzo[a]pyrene, at relatively high concentrations, was also detected in some black tea samples. This method was also utilized to assess the release of PAHs from tea leaves into the liquor.     

Automated liquid-solid extraction of pyrene from soil on centrifugal microfluidic devices

Organic pollutants such as polycyclic aromatic hydrocarbons (PAHs) are present in the environment in increasing concentrations and so are of growing concern. Monitoring these species, particularly on-site, can be both difficult and expensive. This paper presents a novel miniaturised magnetically actuated liquid-solid extraction unit integrated in tandem with a filtration unit and a detection unit on a single centrifugal microfluidic device. A demonstration analyte, pyrene, was rapidly extracted and quantified by UV-absorbance from multiple soil samples. The system showed excellent performance for a system designed for field use. Characterization of two types of passive valves was performed along with an extraction time efficiency study. The system provides a factor of 150 reduction in sample weights and extraction solvent volumes and provides statistically similar recoveries to the conventional method with a pyrene detection limit of 1 ppm (0.03 μg absolute detection limit). The reduction in time and solvent and the potential for field use suggest that this device type may be valuable for environmental monitoring.     

Highly sensitive and selective sensing platform based on π–π interaction between tricyclic aromatic hydrocarbons with thionine–graphene composite

We are just beginning to exploit the fascinating potential of thionine, called electrochemical probe that can selectively recognize specific polycyclic aromatic hydrocarbons (PAHs), as tools for the detection of tricyclic aromatic hydrocarbons phenanthrene (PHE) and anthracene (ANT). A novel electrochemical sensing platform by modification of electroactive thionine functionalized graphene onto glass carbon electrode (Th/GRs/GCE) surface was constructed. The immobilized thionine showed a remarkable stability, which may benefit from the π–π stacking force with graphene. Under optimum conditions, the proposed electrochemical sensor exhibited high sensitivity and low detection limit for detecting PHE and ANT. The total amount of PHE and ANT could be quantified in a wide range of 10 pM–0.1 μM with a good linearity (R² = 0.9979) and a low detection limit of 0.1 pM (S/N = 3). Compounds which possess one or two benzene rings or PAHs with more than three rings, such as benzene, naphthalene (NAP), benzo[a]pyrene (BaP) and pyrene (PYR) show little interference on the detection. Consequently, a simple and sensitive electrochemical method was proposed for the determination of PHE and ANT, which was used to determine PHE and ANT in waste water samples. The electrochemical method provides a general tool that complements the commonly used spectroscopic methods and immune method for the detection of PAHs.     

气相色谱-串联质谱法同时测定卷烟滤嘴中15种多环芳烃

建立了气相色谱-串联质谱同时检测卷烟滤嘴中15种多环芳烃的方法。卷烟滤嘴用二氯甲烷振荡萃取后,经0.22μm有机相滤膜过滤,采用DB-5MS色谱柱(30 m×0.25 mm,0.25μm)进行分离,电子轰击源、正离子模式下以多反应监测模式进行检测,内标法进行定量。15种多环芳烃(苊烯、苊、芴、菲、蒽、荧蒽、芘、苯并[a]蒽、屈、苯并[b]荧蒽、苯并[k]荧蒽、苯并[a]芘、二苯并[a,h]蒽、苯并[g,h,i]苝和茚并[1,2,3-c,d]芘)的线性关系良好,相关系数(R~2)为0.991 4~0.999 9。15种多环芳烃在低、中、高3个添加水平下的平均回收率为81.6%~111.2%;除了芴在低添加水平时相对标准偏差为19.2%外,其他相对标准偏差均小于16%。15种多环芳烃的检出限为0.02~0.24 ng/滤嘴,定量限为0.04~0.80 ng/滤嘴。方法前处理简便,具有快速、准确、灵敏度高及重复性好的优点,适用于卷烟滤嘴中多环芳烃的分析。     

Ultra-trace determination of Persistent Organic Pollutants in Arctic ice using stir bar sorptive extraction and gas chromatography coupled to mass spectrometry

This study presents the optimization and application of an analytical method based on the use of stir bar sorptive extraction (SBSE) gas chromatography coupled to mass spectrometry (GC–MS) for the ultra-trace analysis of POPs (Persistent Organic Pollutants) in Arctic ice. In a first step, the mass-spectrometry conditions were optimized to quantify 48 compounds (polycyclic aromatic hydrocarbons, brominated diphenyl ethers, chlorinated biphenyls, and organochlorinated pesticides) at the low pg/L level. In a second step, the performance of this analytical method was evaluated to determine POPs in Arctic cores collected during an oceanographic campaign. Using a calibration range from 1 to 1800 pg/L and by adjusting acquisition parameters, limits of detection at the 0.1–99 and 102–891 pg/L for organohalogenated compounds and polycyclic aromatic hydrocarbons, respectively, were obtained by extracting 200 mL of unfiltered ice water. α-hexachlorocyclohexane, DDTs, chlorinated biphenyl congeners 28, 101 and 118 and brominated diphenyl ethers congeners 47 and 99 were detected in ice cores at levels between 0.5 to 258 pg/L. We emphasise the advantages and disadvantages of in situ SBSE in comparison with traditional extraction techniques used to analyze POPs in ice.     

The application of an in vitro gastrointestinal extraction to assess the oral bioaccessibility of polycyclic aromatic hydrocarbons in soils from a former industrial site

The total and bioaccessible concentration of 16 polycyclic aromatic hydrocarbons (PAHs) in soil from a former industrial site was investigated. Typical total concentrations across the sampling sites ranged from 1.5 mg kg⁻¹ for acenaphthylene up to 243 mg kg⁻¹ for fluoranthene. The oral bioaccessibility of PAHs in soil was assessed using an in vitro gastrointestinal extraction (Fed Organic Estimation human Simulation Test, FOREhST method). The oral bioaccessibility data indicated that fluorene, phenanthrene, chrysene, indeno(1,2,3-cd)pyrene and dibenzo(a,h)anthracene had the highest % bioaccessible fraction (based on their upper 75th percentile values being >60%) while the other PAHs had lower % bioaccessible fractions (means ranging between 35 and 59%). Significantly lower bioaccessibilities were determined for naphthalene. With respect to method validation and inter-laboratory comparison, the total and bioaccessible concentrations of benzo(a)anthracene, benzo(b)anthracene, benzo(k)fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene and dibenzo(a,h)anthracene was compared to published data derived using the same samples. The total PAH concentrations at the site were compared with generic assessment criteria (GAC) using the residential land use scenario (with plant uptake at 6% soil organic matter). Concentrations of 7 of the PAHs investigated within the soils could lead to an unacceptable risk to human health at this site.     

A novel miniaturized homogenous liquid–liquid solvent extraction-high performance liquid chromatographic-fluorescence method for determination of ultra traces of polycyclic aromatic hydrocarbons in sediment samples

A novel technique called miniaturized homogeneous liquid–liquid extraction (MHLLE) followed by high performance liquid chromatographic-fluorescence detection (HPLC-FL) was developed for the extraction and determination of some polycyclic aromatic hydrocarbons (PAHs) as model for analytical problem in sediment samples. The method is based on the rapid extraction of PAHs from a methanolic sample solution into 0.5 mL n-hexane, as a solvent of lower density than water. After addition of water, the extracting solvent immediately forms a distinct water-immiscible phase at the top of the vial, which can be easily separated, evaporated and re-dissolved in 25 μL of methanol and injected to the HPLC instrument. The parameters affecting the extraction process such as type and volume of organic extraction solvent, extraction time, and salt addition were investigated and the partition coefficient between methanol/water–n-hexane phases was evaluated and used to predict the extraction efficiency. Under optimal conditions, the limits of detection were estimated for the individual PAHs as 3S_b (three times of the standard deviation of baseline) of the measured chromatogram, are in the range of 0.003–0.04 ng g⁻¹ for sediment samples. The relative recoveries of PAHs at spiking levels of 1.0 ng g⁻¹ for sediment samples were in the range of 81–92%. The method was also applied to a corresponding standard references materials (IAEA-408) successfully. The proposed method is very fast, simple, and sensitive without any need for stirring and centrifugation.     

Isolation and analysis of polycyclic aromatic hydrocarbons from natural water using accelerated solvent extraction followed by gas chromatography-mass spectrometry

An innovative analytical procedure for the analysis of polycyclic aromatic hydrocarbons (PAHs) from large-volume water samples is presented. It involves sample preparation, sampling and the elution process in an automated continuous procedure involving the ASE technique. Prior to sampling, a XAD-2 resin column is prepared on the basis of a commercial accelerated solvent extraction (ASE) cartridge so that the resin bed is permanently fixed. Then, the XAD column inside the ASE cartridge is cleaned and conditioned. The sampling procedure involves conventional filtration with subsequent isolation of dissolved PAHs on an XAD-2 resin contained in the ASE cartridge. After sampling, the XAD-2 resin content inside the cartridge is eluted by ASE without any further sample preparation and subsequently reused. In order to validate the procedure, the PAHs were isolated from water samples from the Lake Maggiore (North of Italy) using both XAD-2 resin adsorption and hexane liquid-liquid extraction according to the International Standard Methodology ISO 17993. The mean percentages of deviation between concentrations obtained by both methodologies range from 6% for benzo(a)pyrene to 15% for fluoranthene and benzo(b,k)fluoranthene. Compared to the traditional techniques, this procedure offers numerous practical advantages: easy to perform, fast, savings in solvent volume and in time, all steps are fully automated thus avoiding any XAD-2 resin manipulation during and between steps and moreover, low detection limits were provided (0.001 ng l⁻¹ for chrysene, benzo(b,k)fluoranthene, benzo(a)pyrene, dibenz(a,h)anthracene, benzo(g,h,i)perylene and indeno(1,2,3-cd)pyrene, and 0.01 ng l⁻¹ for acenaphthylene and fluoranthene).This procedure was developed in the frame of a project aimed at evaluating the diffuse input of organic contaminants in the Lake Maggiore.     

Determination of 16 polycyclic aromatic hydrocarbons in milk and related products using solid-phase microextraction coupled to gas chromatography-mass spectrometry

A method for the determination of 16 polycyclic aromatic hydrocarbons (PAHs) in milk and related products based on direct immersion-solid phase microextraction (DI-SPME) followed by gas chromatography-mass spectrometry detection (GC-MS) has been developed. The influence of various parameters on PAH extraction efficiency was carefully monitored. Good performance (recovery, precision and quantitation limits) was attained when a PDMS/DVB fiber was immersed in the sample for 60 min at 55 °C. Detection limits ranged from 0.003 to 1.5 μg L⁻¹ at a signal-to-noise ratio of 3, depending on the compound and the sample. The proposed method was successfully applied to infant formulas, milk and related products and the presence of both fluoranthene and pyrene in two samples was confirmed.     

Low toxic dispersive liquid–liquid microextraction using halosolvents for extraction of polycyclic aromatic hydrocarbons in water samples

A low toxic dispersive liquid–liquid microextraction (LT-DLLME) combined with gas chromatography–mass spectrometry (GC–MS) had been developed for the extraction and determination of 16 polycyclic aromatic hydrocarbons (PAHs) in water samples. In normal DLLME assay, chlorosolvent had been widely used as extraction solvents; however, these solvents are environmental-unfriendly. In order to solve this problem, we proposed to use low toxic bromosolvent (1-bromo-3-methylbutane, LD₅₀ 6150 mg/kg) as the extraction solvent. In this study we compared the extraction efficiency of five chlorosolvents and thirteen bromo/iodo solvents. The results indicated that some of the bromo/iodo solvents showed better extraction and had much lower toxicity than chlorosolvents. We also found that propionic acid is used as the disperser solvent, as little as 50 μL is effective. Under optimum conditions, the range of enrichment factors and extraction recoveries of tap water samples are ranging 372–1308 and 87–105%, respectively. The linear range is wide (0.01–10.00 μg L⁻¹), and the limits of detection are between 0.0003 and 0.0078 μg L⁻¹ for most of the analytes. The relative standard deviations (RSD) for 0.01 μg L⁻¹ of PAHs in tap water were in the range of 5.1–10.0%. The performance of the method was gauged by analyzing samples of tap water, sea water and lake water samples.