Sensitive voltammetric determination of diclofenac using room-temperature ionic liquid-modified carbon nanotubes paste electrode

An ionic liquid-modified carbon nanotubes paste electrode (IL/CNTPE) has been fabricated using hydrophilic ionic liquid (n-hexyl-3-methylimidazolium hexafluoro phosphate) as a binder. This electrode showed enhanced electrochemical response and strong analytical activity towards the direct electrochemical oxidation of diclofenac (DCF). The electron transfer coefficient, α, and charge transfer resistance (R _ct) of DCF at the modified electrode were calculated. Under optimal conditions at pH 7.0, the anodic peak currents increased linearly with the concentration of DCF in the range of 0.5–300 μmol L^?1 with a detection limit of 0.2 μmol L^?1 (3σ). The interferences of foreign substances were investigated. Differential pulse voltammetry was used to check the applicability of the proposed sensor to the determination of DCF in real samples with satisfactory results.     

Ionic liquid/multiwall carbon nanotubes paste electrode for square wave voltammetric determination of methyldopa

Ionic liquid/multiwall carbon nanotubes paste electrode has been used as a novel sensor for the efficient quantitative determination of methyldopa (MDOP) in pharmaceutical and biological samples by using square wave voltammetry. This new sensor shows a better electrochemical response with lower over-potential and high sensitivity for MDOP compared with unmodified carbon paste electrode in physiological condition. The electro-oxidation of MDOP occurred in a pH-dependent 2e^? and 2H⁺ process, and the electrode reaction followed a diffusion-controlled pathway. Under the optimum conditions, the voltammetric oxidation peak current of MDOP showed two linear dynamic ranges with a detection limit of 0.1 μM for MDOP. The novel sensor has been found selective and successfully implemented for the determination of MDOP in real samples such as tablet and patient urine.     

Sensitive voltammetric determination of cysteamine using promazine hydrochloride as a mediator and modified multi-wall carbon nanotubes carbon paste electrodes

This paper presents a sensitive electrochemical method for the determination of cysteamine (CA) using promazine hydrochloride-modified multi-wall carbon nanotubes carbon paste electrode (PrH/MWCNTs CPE). Because of the good electrochemical activity of MWCNTs and the acceptable performance of promazine hydrochloride (PrH) as an electrocatalytic mediator, the modified electrode significantly enhanced the sensitivity for the detection of CA in comparison to the bare carbon paste electrode (CPE). All chemical parameters such as pH of solution, concentration of PrH and kinetic parameters of the system were investigated. Linear sweep voltammetric (LSV) method was used to follow the electrocatalytic effect of CA on the current–potential response of PrH. Under optimum conditions, the obtained net peak current ?I _p(I _sample???I _blank) was linear with CA concentrations in two dynamic ranges of 2.0–346.5 μmol l^?1 (?I _p?=?(0.0195?±?0.0043)C _CA?+?(0.7648?±?0.0397) (r ²?=?0.9948)) and 346.5–1,912.5 μmol l^?1 (?I _p?=?(0.0100?±?0.0026)C _CA?+?(3.8981?±?0.0828) (r ²?=?0.9911)) with a detection limit of 0.8 μmol l^?1. Finally, the PrH/MWCNTs CPE was successfully applied for the determination of CA in urine and drug samples with satisfactory results.     

Highly sensitive electrochemical detection of adenine on a graphene-modified carbon ionic liquid electrode

A new electrochemical method for the sensitive detection of adenine was established on a chitosan (CTS)- and graphene (GR)-modified carbon ionic liquid electrode (CILE). CILE was prepared by mixing 1-butylpyridinium hexafluorophosphate (BPPF₆) and paraffin with graphite powder. Due to the synergistic effects of GR, CILE, and the interaction of GR with IL on the electrode surface, the electrochemical performance of CTS/GR/CILE were greatly enhanced. Electrochemical behaviors of adenine on the modified electrode was investigated with a single well-defined oxidation peak appeared. The electrochemical reaction of adenine was an adsorption-controlled irreversible process, and the electrochemical parameters were further calculated. Under the optimal conditions, the oxidation peak current was proportional to adenine concentration in the range from 1.0 nmol L^?1 to 70.0 μmol L^?1 with a detection limit of 0.286 nmol L^?1 (3σ) by differential pulse voltammetry. The established method showed the advantages such as good selectivity, stability, and repeatability.     

A selective sensor for nanolevel detection of lead (II) in hazardous wastes using ionic-liquid/Schiff base/MWCNTs/nanosilica as a highly sensitive composite

An effective potentiometric sensor had been fabricated for the rapid determination of Pb²⁺ based on carbon paste electrode consisting of room temperature ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF₆), multiwalled carbon nanotubes (MWCNTs), nanosilica, synthesized Schiff base, as an ionophore, and graphite powder. The constructed nanocomposite electrode showed better sensitivity, selectivity, response time, response stability, and lifetime in comparison with typical Pb²⁺ carbon paste electrode for the successfully determination of Pb²⁺ ions in water and in waste water samples. The best response for nanocomposite electrode was obtained with electrode composition of 18% ionophore, 20% BMIM-PF₆, 49% graphite powder, 10% MWCNT, and 3% nanosilica. The new electrode exhibited a Nernstian response (29.76?±?0.10 mV decade^?1) toward Pb²⁺ ions in the range of 5?×?10^?9?C1.0?×?10^?1 mol L^?1 with a detection limit of 2.51?×?10^?9 mol L^?1. The potentiometric response of prepared sensor is independent of the pH of test solution in the pH range of 4.5?C8.0. It has quick response with response time of about 6 s. The proposed electrode show fairly good selectivity over some alkali, alkaline earth, transition, and heavy metal ions.     

A calix[4]arene derivative-doped perchlorate-selective membrane electrodes with/without multi-walled carbon nanotubes

In this study, poly (vinyl chloride)(PVC) membrane electrodes with/without multi-walled carbon nanotubes (MWCNTs) based on a calix[4]arene derivative for perchlorate ion were described. The influence of membrane composition, pH, conditioning solution on the potentiometric response of the electrodes was investigated. Perchlorate-selective PVC membrane electrode exhibited a slope of 47.8 ± 0.6 mV/pClO₄ in the range of 1.0 × 10^?7–1.0 × 10^?1 mol L^?1at pH 4.0 while the coated Pt electrodes with MWCNT-OH, MWCNT-COOH and MWCNT displayed slopes of 46.1 ± 0.7 mV/pClO₄ (5.0 × 10^?6–1.0 × 10^?1 mol L^?1), 50.4 ± 1.9 mV/pClO₄ (1.0 × 10^?6–1.0 × 10^?1 mol L^?1) and 44.4 ± 0.3 mV/pClO₄ (1.0 × 10^?5–1.0 × 10^?1 mol L^?1), respectively. Other response characteristics of these electrodes such as response time, lifetime and detection limit were identified, and the selectivity coefficients towards various anions were calculated by separate solution method. Moreover, the perchlorate-selective electrodes described here were successfully used as an indicator electrode for the determination of perchlorate in real samples such as tap water, river water and human urine by direct calibration method.     

Electrooxidation of hydrazine in alkaline medium at carbon paste electrode decorated with poly(<Emphasis Type="Italic">P</Emphasis>-phenylendiamine/ZnO) nanocomposite

In this study, poly(P-phenylenediamine/ZnO) (PpPD/ZnO) nanocomposite (NC) under ultrasonic conditions was synthesized and characterized. The presence of zinc oxide nanoparticles changed the morphology of PpPD considerably as confirmed by SEM observations. Hydrazine electrooxidation at novel modified carbon paste electrodes (CPE) with supported NC was investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronoamperometry (CA) techniques. Obtained results showed that the NC increases the surface catalytic activity of CPE toward hydrazine electrooxidation. The electrocatalytic current density increased linearly with hydrazine concentration, and the detection limit and sensitivity are determined to be 24 μM and 0.172 mA cm^?2 mM^?1, respectively. As revealed by the EIS measurements, the increased conductivity and decreased R _ct are owing to the presence of ZnO NPs in the PpPD matrix. The CA results indicated that hydrazine electrooxidation results in higher steady-state current density on CPE/PpDP/ZnO electrode system compared to the CPE/PpDP and CPE electrodes.     

Novel nanostructured electrochemical sensor for voltammetric determination of N-acetylcysteine in the presence of high concentrations of tryptophan

A carbon paste electrode chemically modified with multiwall nanotubes and ethynylferrocene (ETFc) was used as a selective and sensitive electrochemical sensor for the determination of minor amounts of N-acetylcysteine (N-AC) in the presence of a high concentration of tryptophan (Trp). Square wave voltammetry (SWV) of N-AC at the modified electrode exhibited linear dynamic range with a detection limit (3 s) of 0.08 μmol?L^?1. The separations of anodic peak potentials of N-AC and Trp reached 400 mV using SWV. With good selectivity and sensitivity, the present method provides a simple method for selective detection of N-AC in real samples such as drug and urine.     

Electrochemical and catalytic investigations of epinephrine,acetaminophen and folic acid at the surface of titanium dioxide nanoparticle-modified carbon paste electrode

In the present paper, the use of a carbon paste electrode modified with 1-(4-(1, 3-dithiolan-2-yl)-6, 7-dihydroxy-2-methyl-6, 7-dihydrobenzofuran-3-yl)ethanone (DDE) and TiO₂ nanoparticles prepared by a simple and rapid method was described. The modified electrode showed excellent properties for electrocatalytic oxidization of epinephrine (EP), acetaminophen (AC) and folic acid (FA). The apparent charge transfer rate constant, k _s?=?1.14 s^?1, and transfer coefficient, α?=?0.54, for electron transfer between the modifier and carbon paste electrode were calculated. It has been found that under optimum condition (pH?=?7.0) in cyclic voltammetry, the oxidation of EP occurs at a potential about 280 mV less positive than that of an unmodified carbon paste electrode. The values of transfer coefficients (α?=?0.46), catalytic rate constant (k?=?1.2?×?10⁴ M^?1 s^?1) and diffusion coefficient (D?=?2.70?×?10^?5 cm² s^?1) were calculated for EP. Differential pulse voltammetry (DPV) exhibited two linear dynamic ranges of 0.5 to 50.0 μM and 50.0 to 1,000 μM for EP. This modified electrode is quite effective not only for the detection of EP, AC and FA but also for the simultaneous determination of these species in a mixture. The limit of detection for EP, AC and FA is 0.10, 1.80 and 2.36 μM, respectively.     

Highly sensitive electrochemical detection of dopamine and uric acid on a novel carbon nanotube-modified ionic liquid-nanozeolite paste electrode

A novel biosensor has been constructed by incorporating modified nanosized natural zeolite and 3-hydroxypropanaminium acetate (HPAA) as a novel room temperature ionic liquid, supported on multiwalled carbon nanotube (MWCNTs) and employed for the simultaneous determination of dopamine (DA) and uric acid (UA). A detailed investigation by transmission electron microscopy and electrochemistry is performed in order to elucidate the preparation process and properties of the composites. The voltammetric studies using the modified carbon paste electrode show two well-resolved anodic peaks for DA and UA with a potential difference of 160 mV, revealing the possibility of the simultaneous electrochemical detection of these compounds. The modified carbon paste electrode shows good conductivity, stability, and extraction effect due to the synergic action of HPAA, MWCNTs, and iron ion-doped natrolite zeolite. Under optimized conditions, the peak currents are linear from 8.12?×?10^?7 to 3.01?×?10^?4?mol?L^?1 and from 9.31?×?10^?7 to 3.36?×?10^?4?mol?L^?1 with detection limits of 1.16?×?10^?7 and 1.33?×?10^?7?mol?L^?1 for DA and UA using the differential pulse voltammetric method, respectively. Finally, the modified carbon paste electrode proved to have good sensitivity and stability and is successfully applied for the simultaneous determination of DA and UA in human blood serum and urine samples.     

Voltammetric sensor for simultaneous determination of ascorbic acid,acetaminophen, and tryptophan in pharmaceutical products

A novel carbon paste electrode modified with carbon nanotubes and 5-amino-2′-ethyl -biphenyl-2-ol was fabricated. The electrochemical study of the modified electrode, as well as its efficiency for electrocatalytic oxidation of ascorbic acid (AA), is described. The electrode was employed to study the electrocatalytic oxidation of AA, using cyclic voltammetry, chronoamperometry, and square-wave voltammetry (SWV) as diagnostic techniques. It has been found that the oxidation of AA at the surface of modified electrode occurs at a potential of about 250 mV less positive than that of an unmodified carbon paste electrode. SWV exhibits a linear dynamic range from 2.0?×?10^?7 to 5.0?×?10^?4 M and a detection limit of 1.0?×?10^?7 M for AA. In addition, this modified electrode was used for simultaneous determination of AA, acetaminophen (AC), and tryptophan (TRP). Finally, the modified electrode was used for determination of AA, AC, and TRP in pharmaceutical products.     

Selective and sensitive voltammetric sensor based on modified multiwall carbon nanotubes paste electrode for simultaneous determination of l-cysteine and folic acid

This paper reports the selective and sensitive voltammetric determination of l-cysteine in the presence of folic acid using ethynylferrocene modified carbon nanotubes paste electrode in 0.1 M phosphate buffer solution (pH 7.0). Using square wave voltammetry, we could measure l-cysteine and folic acid in one mixture independently from each other by a potential difference of about 410 mV for the first time. Square wave voltammetric peak current of l-cysteine and folic acid increased linearly with their concentrations in the ranges of 0.2–250.0 and 1.0–500.0 μmol?L^?1, respectively. The detection limits of 0.07 and 0.6 μmol?L^?1 were achieved for l-cysteine and folic acid, respectively. The proposed voltammetric sensor was successfully applied to the determination of l-cysteine and folic acid in real samples.     

ZnO nanoparticle-modified ionic liquid-carbon paste electrodefor voltammetric determination of folic acid in food and pharmaceutical samples

In this work, a ZnO/nanoparticles (NPs) modified carbon ionic liquid paste electrode (ZnO/NP/CILPE) was fabricated and used to investigate the electrochemical behavior of folic acid. ZnO/NP/CILPE was prepared by mixing hydrophilic ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄mim]-[PF₆])), ZnO/NPs, graphite powder, and liquid paraffin together. The fabricated ZnO/NP/CILPE showed great electrocatalytic ability to the oxidation of folic acid, and an irreversible oxidation peak appeared at 0.75 V (vs. Ag/AgCl) with improved peak current. Under the optimized conditions of pH 9.0, the plot of peak current vs. folic acid concentration consisted of two linear segments with slopes of 1.776and 0.033 μA/μM in the concentration ranges of 0.05–1.5 μM and 1.5–550.0 μM, respectively. The detection limit was 0.01 μM (3σ). The proposed sensor was successfully applied for the determination of folic acid in fortified food and pharmaceutical samples.     

Voltammetric behavior of bupirimate fungicide and its square wave voltammetric determination

The voltammeric behavior of bupirimate fungicide has been studied by square wave stripping voltammetry (SWSV). The insoluble R–HgS salt (where R is the bupirimate frame excluding sulfur) formed on the static hanging mercury drop electrode (SHMDE) was electrochemically reduced by giving a fairly well defined cathodic peak within the pH range of 1.0 to 8.0. The peak potentials (E _p) were shifted toward more negative values with increasing pH, and a maximum peak response appeared at ?1320 mV (vs. Ag/AgCl) at a pH 6.0. The calibration plot was a straight line in the range of 0.013 to 9.43 mg L^?1. The detection limit at pH 6.0 was measured as 4.0 μg L^?1 under the conditions of E _acc?=??700 mV and t _acc?=?10 s. The validity of the recommended method was assessed from the recoveries of spiked tap water, natural peach juice, and commercial peach juice.     

The effect of different concentrations of Na2SnO3 on the electrochemical behaviors of the Mg-8Li electrode

In this research, the effect of the different concentrations of NaSnO₃ as the electrolyte additive in 0.7 mol L^?1 NaCl solution on the electrochemical performances of the magnesium-8lithium (Mg-8Li) electrode are investigated by methods of potentiodynamic polarization, potentiostatic current-time, electrochemical impedance technique, and scanning electron microscopy (SEM). The corrosion resistance of the Mg-8Li electrode is improved when Na₂SnO₃ is added into the electrolyte solution. The potentiostatic current-time curves show that the electrochemical behaviors of the Mg-8Li electrode in the electrolyte solution containing 0.20 mmol L^?1 Na₂SnO₃ is the best. The electrochemical impedance spectroscopy results indicate that the polarization resistance of the Mg-8Li electrode decreases in the following order with the concentrations of Na₂SnO₃: 0.05 mmol L^?1?>?0.00 mmol L^?1?>?0.30 mmol L^?1?>?0.10 mmol L^?1?>?0.20 mmol L^?1. The scanning electron microscopy studies indicate that the electrolyte additive prevents the formation of the dense oxide film on the alloy surface and facilitates the peeling off of the oxidation products.     

Electrochemical detection of trace cadmium in soil using a Nafion/stannum film-modified molecular wire carbon paste electrodes

In this paper, a novel Nafion polymer-coated stannum film-modified carbon paste electrode was developed for the analysis of trace cadmium by square wave anodic stripping voltammetry. The electronic conductive material—molecular wire (diphenylacetylene)—was employed as the binder instead of traditional mineral oil for fabricating this electrode. It was found that the prepared electrode possessed excellent electrochemical performance and increased electron transfer rate due to the introduction of molecular wire as a binder, and exhibited a better sensitivity and stability as well as high resistance to surfactants due to the synergistic effect of Nafion and stannum film. Under the optimal conditions, the stripping peak currents showed a good linear relationship with the Cd(II) concentration in the range from 1.0 to 80.0 μg L^?1 with a detection limit of 0.13 μg L^?1 (S/N?=?3). The developed electrode was further applied to the determination of Cd(II) in soil extracts with satisfactory results.     

Sensitive and selective electrochemical sensor for magnolol based on the enhancement effect of multiwalled carbon nanotubes

Herein, insoluble multiwalled carbon nanotubes (MWNTs) were dispersed into N,N-dimethylformamide (DMF) via ultrasonication, resulting in a stable and homogeneous MWNTs suspension. After evaporation of DMF, the surface of glassy carbon electrode was successfully coated with MWNTs film, as confirmed from scanning electron microscopy measurements. In pH 7 phosphate buffer, an irreversible oxidation peak was observed for magnolol, and the peak currents greatly increased on MWNTs film surface. The influences of pH value, amount of MWNTs and accumulation conditions were studied. Based on the remarkable enhancement effect of MWNTs, a new electrochemical sensor with high sensitivity was developed for magnolol. The linear range was from 5 μg?L^?1 to 1 mg?L^?1, and the detection limit was 2 μg?L^?1 (7.51?×?10^?9?M) after a 3-min accumulation. This novel sensor was successfully used to detect the content of magnolol in Chinese traditional medicines, and the recovery was over the range from 98.1 to 99.1 %.     

Electrochemical methods for determination of thymine in medical pipefish samples based on HPMαFP/Ppy/GCE-modified electrode

A sensitive electrochemical method was developed for the voltammetric determination of thymine at a composite film-modified electrode 1-phenyl-3-methyl-4-(2-furoyl)-5-pyrazolone (HPMαFP)/polypyrrole (Ppy)/glassy carbon electrode (GCE). The electrochemical parameters of thymine were investigated by cyclic voltammetry and differential pulse voltammetry. In pH?=?7.4, one sensitive oxidation peak of thymine with E _pa?=?0.968 V was observed on the HPMαFP/PPy-modified electrode. The difference of peak potential (?E _pa) was 188 mV lower than that for bare GCE. Compared to the bare GCE and Ppy/GCE, the HPMαFP/Ppy/GCE-modified electrode showed an excellent electrocatalytic effect on the oxidation of thymine and displayed a shift of the oxidation potential in the negative direction with significant increase in the peak current. Under the optimum condition, the concentration calibration range and detection limit are 2?×?10^?6–1?×?10^?4 and 4.85?×?10^?7?M for thymine. This developed method had been applied to the direct determination of thymine in medical pipefish samples with satisfactory results.     

Electrocatalytic oxidation of <Emphasis Type="SmallCaps">l</Emphasis>-tyrosine at carboxylic acid functionalized multi-walled carbon nanotubes modified carbon paste electrode

The electrocatalytic oxidation of l-tyrosine (Tyr) was investigated on a carboxylic acid functionalised multi-walled carbon nanotubes modified carbon paste electrode using cyclic voltammetry and amperometry. The surface morphology of the electrodes was studied using field emission (FE)-SEM images, and the interface properties of bare and modified electrodes were investigated by electrochemical impedance spectroscopy (EIS). The influence of the amount of modifier loading and the variation of the pH of the solution on the electrochemical parameters have been investigated. Cyclic voltammetry was carried out to study the electrochemical oxidation mechanism of Tyr, which showed an irreversible oxidation process at a potential of 637.0 mV at modified electrode. The anodic peak current linearly increased with the scan rate, suggesting that the oxidation of Tyr at modified electrode is an adsorption-controlled process. A good linear relationship between the oxidation peak current and the Tyr concentration in the range of 0.8–100.0 μM was obtained in a phosphate buffer solution at pH 7.0 with a detection limit of 14.0?±?1.36 nM (S/N?=?3). The practical utility of the sensor was demonstrated by determining Tyr in spiked cow’s milk and human blood serum. The modified electrode showed excellent reproducibility, long-term stability and antifouling effects.     

Voltammetric behaviors of an emerging pollutant benzotriazole on multiwall carbon nanotubes (MWNTs)—Nafion modified electrode in various pH mediums

The electrochemical behaviors of an emerging pollutant, benzotriazole (BTA), at multiwall carbon nanotubes and Nafion modified glassy carbon electrode (MWNTs-Nafion/GCE) were investigated systematically. The electrochemical reduction of BTA was significantly improved by MWNTs-Nafion compared to bare GCE, ascribed to the excellent adsorption capacity and electrocatalytic activity of MWNTs. BTA presented well-defined reduction peaks only at pH <3.0, suggesting the involvement of lots of protons in the reduction process. Peak potential shifted negatively and peak current decreased significantly with pH increase. BTA showed various UV–Vis absorption spectra in acidic and alkaline mediums. Cathodic peak current increased linearly with square root of sweep rate as well as with the concentration of BTA from 3.0?×?10^?6 to 1.6?×?10^?4 mol L^?1. This suggests a diffusion-controlled and irreversible electrode process. Diffusion coefficient of BTA on MWNTs-Nafion/GCE was obtained as 2.67?×?10^?2 cm² s^?1 with four orders of magnitude larger than that on GCE. MWNTs-Nafion/GCE showed a good selectivity between BTA and O₂ but poor selectivity between BTA and tolyltriazole.