共查询到19条相似文献,搜索用时 956 毫秒
1.
2.
3.
4.
雨滴撞击索类结构表面可能会激发振动及表面积冰等问题,现有研究多关注于疏水壁面及液滴撞击壁面铺展、回缩特性,鲜见涉及雨滴冲击超疏水壁面压力特性的研究.为此,采用CLSVOF方法对单液滴冲击超疏水固壁面这一过程进行数值计算,分析了液滴速度、初始直径等因素对液滴冲击超疏水壁面的压力特性、液滴动态行为特性及液滴与壁面接触时间的影响.结果 表明:单液滴撞击超疏水壁面的过程中,接触瞬间在接触点附近产生局部高压区,而在液滴铺展过程中,对壁面几乎没有压力冲击;在回缩反弹阶段,壁面受到持续较长时间的压力波动,且压力波动区域不局限于初始接触点附近较小范围.撞击速度或液滴初始直径的增大使壁面受到的冲击更为剧烈,且初始速度对壁面受压的影响更为明显.一定范围内液滴初始直径的增大则会导致接触时间延长. 相似文献
5.
6.
7.
8.
基于有限元法,采用水平集方法捕捉相界面的移动,构建了液滴撞击固体壁面的数值模型.通过修正的幂律模型描述流体的非牛顿剪切变稀特性,探讨了剪切变稀特性对液滴撞击固体壁面后铺展行为的影响,分析了撞击不同浸润性壁面时剪切变稀特性对液滴撞击壁面行为的影响差异.研究结果表明:随着幂律指数m的减小,液滴撞击过程中的黏性耗散减小,液滴的形貌变化及无量纲参数变化更为显著.接触角为55°的情况下:当m降低至0.85时,液滴铺展过程中开始出现显著区别于牛顿流体液滴的振荡现象;当m降低至0.80时,液滴在回缩过程中会出现中心液膜断裂的情况.接触角为100°时,剪切变稀液滴均会出现振荡行为,振荡幅度随着m的减小而增大.接触角为160°时,牛顿流体液滴与剪切变稀液滴均会在回缩过程中弹起,但剪切变稀液滴的弹起速度更快.此外,基于数值计算结果,本文提出了接触角为55°情况下剪切变稀液滴撞击壁面后的最大无量纲铺展直径预测模型. 相似文献
9.
采用FLIR红外热像仪对离子液体及其水溶液液滴撞击加热平板后的表面温度分布进行研究,分析了液滴铺展直径随平板加热温度及加热时间的变化规律。结果表明:随着液滴与平板加热时间的增加,液滴表面温度分布均由凹状分布变化至均匀分布;随着平板温度的增加,液滴表面温度增加。随着加热时间的增加,水液滴直径缓慢减小,并在某一时刻急剧降低;而对于60wt%离子液体液滴及纯离子液体液滴,液滴直径反而缓慢增加并趋于稳定。随着加热温度的增加,水液滴直径急剧降低的时刻点前移,对于60wt%离子液体溶液液滴,液滴直径变化规律不明显,而对于纯离子液体液滴,液滴直径逐渐增加。 相似文献
10.
壁面温度是影响壁面润湿性的重要外部条件. 为解决液滴铺展中三相接触线处应力集中问题, 已有研究多采用预置液膜假设, 但无法探究壁面温度对润湿性的影响. 本文针对受热液滴在固体壁面上的铺展过程, 基于润滑理论建立了演化模型, 通过数值模拟, 从平衡接触角角度分析了温度影响壁面润湿性及铺展过程的内部机理. 研究表明: 随温度梯度增大, 液滴所受Marangoni效应增强, 致使液滴向低温区的铺展速率加快; 铺展过程中, 位于高温区的接触线与液滴主体部分间形成一层薄液膜, 重力与热毛细力先后主导该区域的铺展; 当液-固或气-液界面张力对温度的敏感度高于另两个界面时, 低温区方向的平衡接触角不断增大, 使壁面润湿性恶化, 导致液滴铺展减慢; 而当气-固界面张力对温度的敏感度高于其他两个界面时, 低温区方向上的平衡接触角将减小, 由此改善壁面润湿性, 加快液滴铺展; 在温度影响壁面润湿性和液滴铺展过程中, 平衡接触角起关键作用. 相似文献
11.
Continuous droplet rebound on heated surfaces and its effects on heat transfer property: A lattice Boltzmann study 下载免费PDF全文
《中国物理 B》2021,(4)
A thermal multiphase lattice Boltzmann(LB) model is used to study the behavior of droplet impact on hot surface and the relevant heat transfer properties.After validating the correctness of the codes through the D~2 law,the simulations of intrinsic contact angle and the temperature-dependent surface tension are performed.The LB model is then used to simulate the droplet impact on smooth and micro-hole heated surface.On the smooth surface,the impinging droplet is reluctant to rebound,unless the intrinsic wettability of the solid surface is fairly good.On the micro-hole surface,however,the micro-holes provide favorable sites for generating a high-pressure vapor cushion underneath the impinging droplet,which thereby facilitates the continuous droplet rebound.For the continuously rebounding droplet.The time evolution of volume and temperature display obvious oscillations.The achievable height of the rebounding droplet increases as the intrinsic wettability of the solid surface becomes better,and the maximum transient heat flux is found to be directly proportional to the droplet rebounding height.Within a certain time interval,the continuous rebounding behavior of the droplet is favorable for enhancing the total heat quantity/heat transfer efficiency,and the influence of intrinsic wettability on the total heat during droplet impingement is greater than that of the superheat.The LB simulations not only present different states of droplets on hot surfaces,but also guide the design of the micro-hole surface with desirable heat transfer properties. 相似文献
12.
13.
The results of study of evaporation of water droplets and NaCl salt solution from a solid substrate made of anodized aluminum are presented in this paper. The experiment provides the parameters describing the droplet profile: contact spot diameter, contact angle, and droplet height. The specific rate of evaporation was calculated from the experimental data. The water droplets or brine droplets with concentration up to 9.1 % demonstrate evaporation with the pinning mode for the contact line. When the salt concentration in the brine is taken up to 16.7 %, the droplet spreading mode was observed. Two stages of droplet evaporation are distinguished as a function of phase transition rate. 相似文献
14.
V. V. Cheverda A. L. Karchevsky I. V. Marchuk O. A. Kabov 《Thermophysics and Aeromechanics》2017,24(5):803-806
The evaporating water droplets on a horizontal heated substrate were experimentally studied. The constantan foil 25 μm thick with a size of 42×35 mm2 was used as a substrate. The experiments were carried out with a single droplet or with an ensemble of two or three droplets on the foil. The temperature of the lower surface of foil was measured by an IR scanner. To determine the heat flux density at evaporation of liquid near the contact line, the Cauchy problem for the heat conduction equation was solved using the thermographic data. The results of calculations showed that the maximal heat flux density takes place in the region of the contact line and exceeds the average heat flux density from the entire surface of foil. This is explained by the heat inflow from the foil periphery to the droplet due to relatively high value of the coefficient of heat conductivity of the foil material and high evaporation intensity in the contact line region. 相似文献
15.
16.
A method for the general correlation of heat transfer effectiveness for sprays impacting vertically downward on a high-temperature surface has been developed. A dimensional analysis showed that the mass velocity of the spray can be substituted for the droplet velocity in the droplet Reynolds and Weber numbers, greatly improving the correlation with the heat flux data in the film boiling regime. The spray Reynolds number, defined as Re s = Gd/ w , and spray Weber number, We s = G 2 d/ 𝜌 σ , were shown to correlate data from many authors covering a wide range of spray parameters. This correlation supports the results of previous parametric experiments, and is analogous to correlations developed for the critical heat flux of sprays and circular jets. Dependence of the heat transfer performance on spray mass flux and droplet diameter represents the influence of the overall heat transfer capacity of the spray as well as the contribution of droplet interactions. The Leidenfrost temperature of the spray was also shown to be dependent on the spray Weber number. 相似文献
17.
18.
基于喷雾冷却时液滴撞击壁面现象,本文采用CLSVOF(coupled level set and volume of fluid)方法对不同工况下单液滴撞壁过程进行数值模拟,获得了单液滴撞击热壁面动态特性;分析了初始速度、液滴直径等初始参数对液滴撞壁后的动态铺展规律以及壁面换热特性的影响规律,获得了上述参数变化时液滴铺展系数和热流密度的变化趋势;探讨了场协同效应、液滴内部气泡以及三线接触点对壁面换热的影响。碰壁现象的研究对于大型制冷机组室外机散热、高热流电子器件散热等领域优化与控制喷雾有重要意义。 相似文献
19.
At the impact of a liquid droplet on a smooth surface heated above the liquid's boiling point, the droplet either immediately boils when it contacts the surface ("contact boiling"), or without any surface contact forms a Leidenfrost vapor layer towards the hot surface and bounces back ("gentle film boiling"), or both forms the Leidenfrost layer and ejects tiny droplets upward ("spraying film boiling"). We experimentally determine conditions under which impact behaviors in each regime can be realized. We show that the dimensionless maximum spreading γ of impacting droplets on the heated surfaces in both gentle and spraying film boiling regimes shows a universal scaling with the Weber number We (γ~We(2/5)), which is much steeper than for the impact on nonheated (hydrophilic or hydrophobic) surfaces (γ~We(1/4)). We also interferometrically measure the vapor thickness under the droplet. 相似文献