Rapid sonochemical synthesis of irregular nanolaminar-like Bi2WO6 as efficient visible-light-active photocatalysts

Irregular Bi₂WO₆ nanolaminars have been successfully synthesized via a rapid sonochemical approach using bismuth nitrate and tungstic acid as precursors in an aqueous solution. The characteristics of them were investigated in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N₂ adsorption, pore value, PL spectroscopy and UV–vis diffuse reflectance spectroscopy (UV–vis DRS). These irregular nanolaminars are of geometric shapes of orthorhombic Bi₂WO₆ with their basal plane being (0 0 1). They possess high crystallinity, lager surface area and pore value, which means fewer traps and stronger photocatalytic activity. The growth mechanism of such special nanolaminar was related to the sonochemical synthesis route, which played a key role in the formation of Bi₂WO₆ nanolaminar. Simultaneously, it was found that the formation of Bi₂WO₆ nanolaminar is a time dependent process. The Bi₂WO₆ nanolaminar has higher photocatalytic activity than bulk Bi₂WO₆ nanoparticle obtained by refluxing method for rhodamine B (Rh.B) degradation under visible light irradiation (λ > 400 nm).     

Synthesis of TiO2/WO3 nanoparticles via sonochemical approach for the photocatalytic degradation of methylene blue under visible light illumination

Through an ultrasound assisted method, TiO₂/WO₃ nanoparticles were synthesized at room temperature. The XRD pattern of as-prepared TiO₂/WO₃ nanoparticles matches well with that of pure monoclinic WO₃ and rutile TiO₂ nanoparticles. TEM images show that the prepared TiO₂/WO₃ nanoparticles consist of mixed square and hexagonal shape particles about 8–12 nm in diameter. The photocatalytic activity of TiO₂/WO₃ nanoparticles was tested for the degradation of a wastewater containing methylene blue (MB) under visible light illumination. The TiO₂/WO₃ nanoparticles exhibits a higher degradation rate constant (6.72 × 10⁻⁴ s⁻¹) than bare TiO₂ nanoparticles (1.72 × 10⁻⁴ s⁻¹) under similar experimental conditions.     

Effect of calcination temperature on phase transformation,structural and optical properties of sol–gel derived ZrO2 nanostructures

Zirconia (ZrO₂) nanostructures of various sizes have been synthesized using sol–gel method followed by calcination of the samples from 500 to 700 °C. The calcined ZrO₂ powder samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infra-red spectroscopy (FT-IR), UV–visible spectroscopy (UV–vis.), Raman spectroscopy (RS) and thermogravimetric analysis (TGA). The phase transformation from tetragonal (t) to monoclinic (m) was observed. The average diameter of the ZrO₂ nanostructures calcined at 500, 600 and 700 °C was calculated to be 8, 17 and 10 nm, respectively. The ZrO₂ sample calcined at 500 °C with tetragonal phase shows a direct optical band gap of 5.1 eV. The value of optical band gap is decreased to 4.3 eV for the ZrO₂ calcined at 600 °C, which contains both tetragonal (73%) and monoclinic (27%) phases. On further calcination at 700 °C, where the ZrO₂ nanostructures have 36% tetragonal and 64% monoclinic phases, the optical band gap is calculated to be 4.8 eV. The enhancement in optical band gap for ZrO₂ calcined at 700 °C may be due to the rod like shape of ZrO₂ nanostructures. The tetragonal to monoclinic phase transformation was also confirmed by analyzing Raman spectroscopic data. The TG analysis revealed that the ZrO₂ nanostructure with dominance of monoclinic phase is found to be more stable over the tetragonal phase. In order to confirm the phase stability of the two phases of ZrO₂, single point energy is calculated corresponding to its monoclinic and tetragonal structures using density functional theory (DFT) calculations. The results obtained by theoretical calculations are in good agreement with the experimental findings.     

Effects of morphology on photocatalytic performance of Zinc oxide nanostructures synthesized by rapid microwave irradiation methods

In this study, two different chemical solution methods were used to synthesize Zinc oxide nanostructures via a simple and fast microwave assisted method. Afterwards, the photocatalytic performances of the produced ZnO powders were investigated using methylene blue (MB) photodegradation with UV lamp irradiation. The obtained ZnO nanostructures showed spherical and flower-like morphologies. The average crystallite size of the flower-like and spherical nanostructures were determined to be about 55 nm and 28 nm, respectively. X-ray diffraction (XRD), scanning electronic microscopy (SEM), Brunauer–Emmett–Teller (BET), room temperature photoluminescence (RT-PL) and UV–vis analysis were used for characterization of the synthesized ZnO powders. Using BET N₂-adsorption technique, the specific surface area of the flower-like and spherical ZnO nanostructures were found to be 22.9 m²/gr and 98 m²/gr, respectively. Both morphologies show similar band gap values. Finally, our results depict that the efficiency of photocatalytic performance in the Zinc oxide nanostructures with spherical morphology is greater than that found in the flower-like Zinc oxide nanostructures as well as bulk ZnO.     

Ultrasound assisted synthesis of TiO2–WO3 heterostructures for the catalytic degradation of Tergitol (NP-9) in water

TiO₂–WO₃ heterostructures were synthesized at room temperature, ambient pressure, and short reaction time via a sonochemical approach. TEM and EDX images show that the prepared TiO₂–WO₃ heterostructures consist of globular agglomerates (∼250 nm in diameter) composed of very small (<5 nm) dense particles (WO₃) dispersed inside the globules. The observed less intense monoclinic WO₃ diffraction peak (around 2θ = 22° belonging to (0 0 1) plane) and the high intense hexagonal WO₃ diffraction peak (around 2θ = 28° belonging to (2 0 0) plane) in XRD indicate that there may be phase transition occurring due to the formation of intimate bond between TiO₂ and WO₃. In addition, the formation of such new phase was also observed from Raman spectra with a new peak at 955 cm⁻¹, which is due to the symmetric stretching of W = O terminal. The catalytic activity of TiO₂–WO₃ heterostructures was tested for the degradation of wastewater pollutant containing Tergitol (NP-9) by a process combined with ozonation and it showed two-fold degradation rate compared with ozone process alone.     

Tuning of crystal phase structure in hydrated WO3 nanoparticles under wet chemical conditions and studies on their photochromic properties

Hydrated tungsten oxide nanoparticles have been synthesized using a simple wet chemical method while varying the concentration of HCl. XRD studies show that the variation in HCl concentration from 1 M to 6 M in the reaction results into gradual change in crystal structure of hydrated WO₃ from hexagonal (WO₃·0.33H₂O) to pure orthorhombic (WO₃·H₂O), through a series of samples with mixed phase of the two indifferent ratios. The similar variations in the degree of hydration and phase variations have also been observed from Raman, FTIR and TGA studies. The average crystallite size of the hydrated WO₃ particles was estimated to be ～26 nm from XRD line broadening and AFM studies showed the formation of spherical shaped particles for all the samples. The photochromic studies were carried out on the composite films of these materials in the polymeric matrix of polyvinyl alcohol (PVA) while exposing to UV light. The composite films show interesting variations in the photochromic behavior depending on the crystal structure of hydrated WO₃ filler. The photochromic behavior has been explained on the basis of EPR spectra of hydrated WO₃.     

Promotion effect of Pt on a SnO2–WO3 material for NOx sensing

Metal-oxide nanocomposites were prepared over screen-printed gold electrodes to be used as room-temperature NO_x (nitric-oxide (NO) and nitrogen dioxide (NO₂)) sensors. Various weight ratios of SnO₂–WO₃ and Pt loadings were used for NO sensing. The sensing materials were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface analysis. The NO-sensing results indicated that SnO₂–WO₃ (1:2) was more effective than other materials were. The sensor response (S=resistance of N₂/resistance of NO=R_N2/R_NO) for detecting 1000 ppm of NO at room temperature was 2.6. The response time (T₉₀) and recovery time (TR₉₀) was 40 s and 86 s, respectively. By further loading with 0.5% Pt, the sensor response increased to 3.3. The response and recovery times of 0.5% Pt/SnO₂–WO₃ (1:2) were 40 s and 206 s, respectively. The linearity of the sensor response for a NO concentration range of 10–1000 ppm was 0.9729. A mechanism involving Pt promotion of the SnO₂–WO₃ heterojunction was proposed for NO adsorption, surface reaction, and adsorbed NO₂ desorption.     

Optical detection of organic hydrides with platinum-loaded tungsten trioxide

Tungsten trioxide powder with loading 0.1 wt% platinum (Pt/WO₃) was prepared for optical detection of organic hydrides such as cyclohexane, decalin by impregnation with PtCl₆^2? and subsequent calcination in air at 500 °C. The scanning electron microscopic observation of Pt/WO₃ shows that the Pt particles with mean diameters of 80–100 nm were on the surface of the WO₃ powder. The Pt/WO₃ showed coloration for 13% cyclohexane at higher 100 °C and for 1.3% cyclohexane at 200 °C. The in-situ XRD results of the Pt/WO₃ in coloring/bleaching change indicate that the coloring of Pt/WO₃ was caused by transformation of WO₃ to tungsten bronze. The analysis of reacted gas demonstrates that Pt on WO₃ produces only hydrogen and benzene through dehydrogenation of cyclohexane over 100 °C. It was founded that the Pt/WO₃ has potential of optical detection of organic hydrides by heating at higher 100 °C.     

Superior performance characteristics for the poly(2,5-dimethoxyaniline)–poly(styrene sulfonic acid)-based electrochromic device

We have fabricated an electrochromic (EC) device with poly(2,5-dimethoxyaniline), PDMA, entrapped in poly(styrene sulfonic acid) (PSS) as an electrochromic layer. The device showed improved performances like stability, optical contrast, etc., over the device with a PDMA layer doped by H₂SO₄. In the process of fabrication of the EC device with a sandwich configuration, indium tin oxide (ITO)/PDMA–PSS||poly(ethyleneimine) (PEI)/orthophosphoric acid (H₃PO₄)/WO₃/ITO, electrochemical polymerization of 2,5-dimethoxyaniline (DMA) was performed with PSS as electrolyte and ITO coated glass as working electrode. The performance characteristics of EC device, like optical contrast, stability, switching time, etc., were followed by cyclic voltammetry, double potential step chronoamperometry and in-situ spectroelectrochemistry. The device was operated in between − 1 V and + 1 V, and absorption characteristics were followed by in-situ UV–visible spectroscopy. A visible contrast in color upon switching the potential from − 1 V to + 1 V was noticed for the device. The device was pale yellow at − 1 V and dark green at + 1 V. Incorporation of PSS into PDMA resulted enhancement in the performance of the complementary electrochromic device. The optical contrast of the device was improved by incorporating PSS into PDMA matrix. The device retained nearly 50% of their optical contrast after 10,000 double steps informing the superior performance of PDMA–PSS in the EC device.     

Surface properties of palladium catalysts supported on ternary ZrO2–Al2O3–WOx oxides prepared by the sol–gel method: Study of the chemical state of the support

The surface properties of Pd and Pd–Pt catalysts supported on binary ZrO₂–WOx and ternary ZrO₂–Al₂O₃–WOx oxides prepared by the sol–gel method were studied. Special attention was paid to the study of the texture of the catalysts as well as the chemical state of tungstated zirconia and tungstated zirconia promoted with alumina in the palladium catalysts. The catalysts were tested in the isomerization of n-hexane and were characterized by N₂ physisorption, XRD, TPR, Raman spectroscopy, XPS and FT-IR of adsorbed pyridine. The catalysts had bimodal pore size distributions with mesopores in the range 55–70 Å and macropores of 1000 Å in diameter. The catalysts had a surface WOx coverage (4.4–6.0 W nm^?2) lower than that of the theoretical monolayer (7.0 W nm^?2). A lower acidity of the ternary ZrO₂–Al₂O₃–WOx oxide as compared to the binary ZrO₂–WOx oxide was found. Higher activity in the isomerisation of n-hexane was obtained in the Pd–Pt catalysts supported on ternary ZrAlW oxides prepared by sol–gel that is correlated with the coexistence on the surface of W⁴⁺ (WO₂) or W⁰ and W⁶⁺ (Al₂(WO₄)₃) species, ZrO₂ in the tetragonal phase and a high amount of ZrOx suboxides species in a low oxidation state (Zr³⁺ and Zr²⁺).     

Fabrication of Fe-doped TiO2 nanoparticles and investigation of photocatalytic decolorization of reactive red 198 under visible light irradiation

In this research, Fe-doped TiO₂ nanoparticles with various Fe concentrations (0. 0.1, 1, 5 and 10 wt%) were prepared by a sol–gel method. Then, nanoparticles were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis (EDX), BET surface area, photoluminescence (PL) spectroscopy and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity of the nano-particles was evaluated through degradation of reactive red 198 (RR 198) under UV and visible light irradiations. XRD results revealed that all samples contained only anatase phase. DRS showed that the Fe doping in the titania induced a significant red shift of the absorption edge and then the band gap energy decreased from 3 to 2.1 eV. Photocatalytic results indicated that TiO₂ had a highest photocatalytic decolorization of the RR 198 under UV irradiation whereas photocatalytic decolorization of the RR 198 under visible irradiation increased in the presence of Fe-doped TiO₂ nanoparticles. Among the samples, Fe-1 wt% doped TiO₂ nanoparticles showed the highest photocatalytic decolorization of RR198 under visible light irradiation.     

Theoretical and experimental investigation on structural and electronic properties of Al/O/Al,O-doped WS2

Effects of the doping atom (O, Al, and (Al, O)) on structural and electronic properties of the monolayer WS₂ have been studied by using first-principles calculations. Results show that the covalent character of W–S bonding has been enhanced after doping. Meanwhile, W–O, Al–S and W–S bonds of (Al, O) co-doped WS₂ monolayer have higher covalent character compared with O-doped and Al-doped WS₂ monolayer of this work. After doping with Al (or Al, O) atoms, Fermi level moves close to the valence band and the dopant atoms produce the defect energy levels, indicating that Al doped and (Al, O) co-doped WS₂ monolayer both have p-type conductivity. O-doped and (Al, O) co-doped WS₂ ultrathin films was prepared on Si substrates. Results of Raman spectra show the formation of the O-doped and (Al, O) co-doped WS₂ films. Moreover, compared with the pure WS₂, the approximate reduction of 0.43 eV and 0.46 eV for W 4f and S 2p in binding energy after (Al, O) co-doped shows that p-type doping of (Al, O) co-doped WS₂ has been verified.     

Electronic behavior of visible light sensitive ZrO2/Cr2O3/carbon clusters composite materials

Nano-sized ZrO₂/Cr₂O₃/carbon clusters composite materials were successfully obtained by the microwave-irradiated calcinations of a Zr(acac)₄/Cr(acac)₃/epoxy resin complex. The compositions of the resulting composite materials were determined using ICP, elemental analysis and surface characterization by XRD, SEM and TEM. The UV–Vis spectra of the composites were also obtained. ESR spectral examinations of the composites indicate that an electron transfer takes place in the process Cr₂O₃ → carbon clusters → ZrO₂. The composite materials have been found to show visible light-responsive catalytic activities.     

UV–visible absorption spectrum determination of optical energy gaps of α and β lithium nitrides

It is well known that a high pressure can induce α–β phase transformation of lithium nitride (Li₃N). However, this work demonstrated that a reverse phase transformation of Li₃N from β to α could occur when it was subjected to heat-treatment at 500 °C in vacuum. Furthermore, the optical properties of α and β lithium nitrides were evaluated by UV–visible spectra. The optical energy gaps (E_g) of α and β lithium nitrides, which were determined from the derivative UV–visible spectra, are 1.81±0.01 and 2.14±0.01 eV, respectively.     

Luminescence properties of Eu3+ and Sm3+ coactivated Gd(III) tungstate phosphor for light-emitting diodes

Rare-earth ions coactivated red phosphors Gd_0.2RE_1.8(WO₄)₃ (RE=Eu³⁺ and Sm³⁺) were synthesized by conventional solid-state reaction using boric acid as a flux agent. The samples were characterized by X-ray diffractometer (XRD), energy-dispersive X-ray spectrometer (EDS) and luminescence spectrometer (LS). The results showed that the Eu–Sm system exhibits higher emission intensity than those of the Eu single-doped system and Sm separate-doped system under ultraviolet (UV) radiation. Samarium(III) ions are effective in broadening and strengthened absorptions around 400 nm. Furthermore, it exhibits enhanced luminescence emission. when the mole ratio of boric acid is about 0.16, the luminescence capability is optimum. Two strongest lines at ultraviolet (394 nm) and blue (465 nm) in excitation spectra of these phosphors match well with the output wavelengths of UV and blue GaN-based light-emitting diodes (LEDs) chips.     

ArF excimer laser deposition of wide-band gap solid electrolytes for thin film batteries

High quality solid electrolyte thin films was grown by pulsed laser deposition (PLD) using a high photon energy ArF excimer laser. Various amorphous thin films were successfully deposited on glass substrates from oxide targets; such as Li₃PO₄, LiBO₂, Li₂SiO₃, Li₂CO₃, Li₂SO₄, Li₂ZrO₃, LiAlO₂, Li₂WO₄ and Ohara glass ceramics. The morphology, optical property and ionic conductivity of these films were examined by optical microscope, UV–VIS spectroscopy and impedance analysis. Dramatic improvement of the film morphology was observed by using a high photon energy laser, while the broken film with many droplets was obtained by using lower ones. Ionic conductivity of the films was examined by impedance spectroscopy and dc polarization method. For example, an ionic conductivity of a Li₃PO₄ film was 4.6 × 10^? 6 S cm^? 1 at 25 °C with activation energy of 0.57 eV. Electronic conductivity measurements revealed that most of the films were pure lithium ion conductors, while a Li₂WO₄ film was a mixed conductor.     

Visible light induced photodesorption of NO from the α-Cr2O3(0001) surface

Nitric oxide chemistry and photochemistry on the Cr-terminated surface of α-Cr₂O₃(0001) were examined using temperature programmed desorption (TPD), sticking coefficient measurements and photodesorption. NO exposed to α-Cr₂O₃(0001) at 100 K binds at surface Cr cation sites forming a strongly bound surface species that thermally desorbs at 320–340 K, depending on coverage. No thermal decomposition was detected in TPD in agreement with previous results in the literature. Sticking probability measurements at 100 K indicated near unity sticking for NO up to coverages of ~ 1.3 ML, with additional adsorption with higher exposures at decreased sticking probability. These results suggest that some Cr cation sites on the α-Cr₂O₃(0001) surface were capable of binding more than one NO molecule, although it is unclear whether this was as separate NO molecules or as dimers. Photodesorption of adsorbed NO was examined for surface coverages below the 1 ML point. Both visible and UV light were shown to photodesorb NO without detectable NO photodecomposition. Visible light photodesorption of NO occurred with a greater cross section than estimated using UV light. The visible light photodesorption event was not associated with bandgap excitation in α-Cr₂O₃(0001), but instead was linked to excitation of a surface Cr^3 +–NO^? charge transfer complex. These results illustrate that localized photoabsorption events at surface sites with unique optical properties (relative to the bulk) can result in unexpected surface photochemistry.     

Magneto-optical properties of α-Fe2O3@ZnO nanocomposites prepared by the high energy ball-milling technique

Magnetic–fluorescent nanocomposites (NCs) with 10 wt% of α-Fe₂O₃ in ZnO have been prepared by the high energy ball-milling. The crystallite sizes of α-Fe₂O₃ and ZnO in the NCs are found to vary from 65 nm to 20 nm and 47 nm to 15 nm respectively as milling time is increased from 2 to 30 h. XRD analysis confirms presence of α-Fe₂O₃ and ZnO in pure form in all the NCs. UV–vis study of the NCs shows a continuous blue-shift of the absorption peak and a steady increase of band gap of ZnO with increasing milling duration that are assigned to decreasing particle size of ZnO in the NCs. Photoluminescence (PL) spectra of the NCs reveal three weak emission bands in the visible region at 421, 445 and 485 nm along with the strong near band edge emission at 391 nm. These weak emission bands are attributed to different defect – related energy levels e.g. Zn-vacancy, Zn interstitial and oxygen vacancy. Dc and ac magnetization measurements show presence of weakly interacting superparamagnetic (SPM) α-Fe₂O₃ particles in the NCs. ⁵⁷Fe-Mössbauer study confirms presence of SPM hematite in the sample milled for 30 h. Positron annihilation lifetime measurements indicate presence of cation vacancies in ZnO nanostructures confirming results of PL studies.     

Temperature dependent structural and optical properties of tin oxide nanoparticles

Nanocrystalline tin oxide (SnO₂) powders were synthesized through wet chemical route using tin metal as precursor. The morphology and optical properties, as well as the effect of sintering on the structural attributes of SnO₂ particles were analyzed using Transmission electron microscopy (TEM), UV–visible spectrophotometry (UV–vis) and X-ray diffraction (XRD), respectively. The data revealed that the lattice strain plays a significant role in determining the structural properties of sintered nanoparticles. The particle size was found to be 5.8 nm, 19.1 nm and 21.7 nm for samples sintered at 300 °C, 500 °C, and 700 °C, respectively. Also, the band gaps were substantially reduced from 4.1 eV to 3.8 eV with increasing sintering temperatures. The results elucidated that the structural and optical properties of the SnO₂ nanoparticles can be easily modulated by altering sintering temperature during de novo synthesis.     

Ultrasonically prepared photocatalyst of W/WO3 nanoplates with WS2 nanosheets as 2D material for improving photoelectrochemical water splitting

A sonochemical treatment has been an emerged technique as an interesting method for fabricating different photocatalysts with unique photoelectrochemical (PEC) properties. This study investigated the PEC performance of WO₃ with WS₂ nanosheets as a 2D material before calcination (WO₃/WS₂-90) and after calcination (WO₃/WS₂-450) prepared with sonochemical treatment. The WS₂ nanosheets were prepared from a liquid exfoliation phase with few-layer nanosheets, approximately 6.5 nm in thickness. The nanosheets were confirmed by UV–Vis spectroscopy and atomic force microscopy. Further, XPS, RAMAN, and SEM-EDAX analyses indicated that, following calcination of the WO₃/WS₂ electrode, the WS₂ nanosheets initially transformed to 2D-WO₃. After depositing the WS₂ nanosheets on the WO₃, the photocurrent density increased substantially. The WO₃/WS₂-450 films after calcination showed a photocurrent density of 5.6 mA.cm⁻² at 1.23 V vs. Ag/AgCl, which was 3.1 and 7.2 times higher, respectively than those of the WO₃/WS₂-90 before calcination and pure WO₃. Mott-Schottky and electrochemical impedance spectroscopy analyses confirmed the fabrication of the WO₃/WS₂ photoanode after calcination. The deposition of WS₂ nanosheets onto pure WO₃ increased the donor concentration (24-fold), reduced the space charge layer (4.6-fold), and decreased the flat band potential (1.6-fold), which could all help improve the photoelectrochemical efficiency. Moreover, the incorporation of WO₃ with WS₂ nanosheets as a 2D material (WO₃/WS₂-450) enhanced the incident photon current efficiency (IPCE) by 55%. In addition, the applied-bias photon-to-current conversion efficiency of the WO₃/WS₂-450 films was approximately 2.26% at 0.75 V (vs. Ag/AgCl), which is 5.6 and 9 times higher, respectively than those of WO₃/WS₂-90 and pure WO₃.