Electrochemical Oxidation and Sensitive Determination of Pyrogallol at Preanodized Screen‐Printed Carbon Electrodes

In this study, we report a simple, low‐cost and rapid electrochemical sensor based on the anodically pretreated screen‐printed carbon electrodes (SPCE*) for the determination of pyrogallol in pH 7.0 buffer solutions. Cyclic voltammetric studies show that SPCE* lowers overpotentials and improve electrochemical behaviour of pyrogallol, compared to untreated SPCE. All experimental parameters were optimized to improve voltammetric responses; excellent analytical features were achieved by flow‐injection amperometric methods. A linear calibration plot was obtained for 10‐1000 μM pyrogallol with a slope of 0.0562 μA/μM. The detection limit (S/N = 3) was 0.33 μM. Interferences from some inorganic salts and organic compounds were studied. The assay was applied to the determination of pyrogallol in tap water and lake water, respectively.     

Electrografting of 4‐tert‐Butylcatechol on GC Electrode. Selective Electrochemical Determination of Homocysteine

A new sensor based on the grafting of 4‐tert‐butylcatechol on the surface of a glassy carbon electrode (GC) was developed for the catalytic oxidation of homocysteine ( Hcy ). The GC‐modified electrode exhibited a reversible redox response at neutral pH. Under the optimum conditions cyclic voltammetric results indicated the excellent electrocatalytic activity of modified electrode toward the oxidation of Hcy at reduced over‐potential about 350 mV. A linear dynamic range of 0.01–3.0 mM and a detection limit of 1.0 µM were obtained for Hcy . The modified electrode was used as an electrochemical sensor for selective determination of Hcy in human blood.     

Highly Sensitive and Selective Adsorptive Stripping Voltammetric Method Employing a Lead Film Screen‐printed Electrode for Determination of Cobalt as its Nioximate Complex

A carbon screen‐printed electrode modified in‐situ with lead film (PbF‐SPCE) was applied for the adsorptive stripping voltammetric determination of Co(II) in the form of a complex with 1,2‐cyclohexanedione dioxime. Lead film was electrochemically deposited in situ on SPCE from a 0.2 M ammonia buffer solution (pH 8.7) containing 5 ? 10^?5 M Pb(NO₃)₂ and 5 ? 10^?5 M nioxime. Due to the very low LOD (0.003 µgL^?1, i.e., 0.05 nmol L^?1 Co(II); t_acc=120s), the developed procedure could be rated among the most sensitive methods employing SPEs. The Ni(II) signal was significantly lower than the Co(II) one and the separation of Ni(II) and Co(II) peaks was even better at the PbF‐SPCE than at the hanging mercury drop electrode.     

Development of a Carbon Paste Electrode Modified with Reduced Graphene Oxide and an Imidazole Derivative for Simultaneous Determination of Biological Species of N‐acetyl‐L‐cysteine,Uric Acid and Dopamine

In this work, the modified carbon paste electrode (CPE) with an imidazole derivative 2‐(2,3 dihydroxy phenyl) 4‐methyl benzimidazole (DHPMB) and reduced graphene oxide (RGO) was used as an electrochemical sensor for electrocatalytic oxidation of N‐acetyl‐L‐cysteine (NAC). The electrocatalytic oxidation of N‐acetyl‐L‐cysteine on the modified electrode surface was then investigated, indicating a reduction in oxidative over voltage and an intensive increase in the current of analyte. The scan rate potential, the percentages of DHPMB and RGO, and the pH solution were optimized. Under the optimum conditions, some parameters such as the electron transfer coefficient (α) between electrode and modifier, and the electron transfer rate constant) k_s) in a 0.1 M phosphate buffer solution (pH=7.0) were obtained by cyclic voltammetry method. The diffusion coefficient of species (D) 3.96×10^?5 cm² s^?1 was calculated by chronoamperometeric technique and the Tafel plot was used to calculate α (0.46) for N‐ acetyl‐L‐cysteine. Also, by using differential pulse voltammetric (DPV) technique, two linear dynamic ranges of 2–18 µM and 18–1000 µM with the detection limit of 61.0 nM for N‐acetyl‐L‐cysteine (NAC) were achieved. In the co‐existence system of N‐acetyl‐L‐cysteine (NAC), uric acid (UA) and dopamine (DA), the linear response ranges for NAC, UA, and DA are 6.0–400.0 µM, 5.0–50.0 µM and 2.0–20.0 µM, respectively and the detection limits based on (C=3s_b/m) are 0.067 µM, 0.246 µM and 0.136 µM, respectively. The obtained results indicated that DHPMB/RGO/CPE is applicable to separate NAC, uric acid (UA) and dopamine (DA) oxidative peaks, simultaneously. For analytic performance, the mentioned modified electrode was used for determination of NAC in the drug samples with acceptable results, and the simultaneous determination of NAC, UA and DA oxidative peaks was investigated in the serum solutions, too.     

Uric Acid Determination by Adsorptive Stripping Voltammetry on Multiwall Carbon Nanotubes Based Screen‐Printed Electrodes

A sensitive electroanalytical methodology for the determination of uric acid in real samples using adsorptive voltammetry at a multiwalled carbon nanotubes (MWCNT) modified screen printed electrode (SPCE) is presented. Adsorption of uric acid takes place at open circuit potential at an optimized pH 5.0. Studies about the effect of accumulation time and scan rate on the analytical signal were developed and confirm the adsorption nature of the electrodic process. Quantitative analysis of uric acid by using its oxidation process at +0.18 V (vs. an Ag pseudoreference electrode) was carried out with an accumulation time of 5 min. Thus, a linear voltammetric based reproducible determination of uric acid (RSD 5 %) in the range 1–100 µM was obtained. The method was then successfully used for the determination of uric acid in real clinical samples of urine without detection of interferences. The proposed methodology only requires a dilution of the real sample and present advantages as low cost and easy handling for non specialized technicians.     

Carbon Paste Electrode Incorporating 1‐[4‐(Ferrocenyl Ethynyl) Phenyl]‐1‐Ethanone for Electrocatalytic and Voltammetric Determination of Tryptophan

A carbon paste electrode spiked with 1‐[4‐ferrocenyl ethynyl) phenyl]‐1‐ethanone (4FEPE) was constructed by incorporation of 4FEPE in graphite powder‐paraffin oil matrix. It has been shown by direct current cyclic voltammetry and double step chronoamperometry that this electrode can catalyze the oxidation of tryptophan (Trp) in aqueous buffered solution. It has been found that under optimum condition (pH 7.00), the oxidation of Trp at the surface of such an electrode occurs at a potential about 200 mV less positive than at an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and rate constant for the chemical reaction between Trp and redox sites in 4FEPE modified carbon paste electrode (4FEPEMCPE) were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of Trp showed a linear dependent on the Trp concentrations and linear calibration curves were obtained in the ranges of 6.00×10^?6 M–3.35×10^?3 M and 8.50×10^?7 M–6.34×10^?5 M of Trp concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 1.80×10^?6 M and 5.60×10^?7 M by CV and DPV methods. This method was also examined as a selective, simple and precise new method for voltammetric determination of tryptophan in real sample.     

Electrochemical Behavior and Electroanalytical Determination of Indole‐3‐Acetic Acid Phytohormone on a Boron‐Doped Diamond Electrode

In this work, a boron‐doped diamond (BDD) electrode was used for the electroanalytical determination of indole‐3‐acetic acid (IAA) phytohormone by square‐wave voltammetry. IAA yielded a well‐defined voltammetric response at +0.93 V (vs. Ag/AgCl) in Britton–Robinson buffer, pH 2.0. The process could be used to determine IAA in the concentration range of 5.0 to 50.0 µM (n=8, r=0.997), with a detection limit of 1.22 µM. The relative standard deviation of ten measurements was 2.09 % for 20.0 µM IAA. As an example, the practical applicability of BDD electrode was tested with the measurement of IAA in some plant seeds.     

Novel Amperometric Hydrogen Peroxide Biosensor Based on Horseradish Peroxidase Azide Covalently Immobilized on Ethynyl‐Modified Screen‐Printed Carbon Electrode via Click Chemistry

A novel, simple and versatile protocol for covalent immobilization of horseradish peroxidase (HRP) on screen‐printed carbon electrode (SPCE) based on the combination of diazonium salt electrografting and click chemistry has been successfully developed. The ethynyl‐terminated monolayers are obtained by diazonium salt electrografting, then, in the presence of copper (I) catalyst, the ethynyl modified surfaces reacted efficiently and rapidly with horseradish peroxidase bearing an azide function (azido‐HRP), thus forming a covalent 1,2,3‐triazole linkage by means of click chemistry. All the experimental results suggested that HRP was immobilized onto the electrode surface successfully without denaturation. Furthermore, the immobilized HRP showed a fast electrocatalytic reduction for H₂O₂. A linear range from 5.0 to 50.0 µM in a phosphate buffer (pH 5.5) with detection limit of 0.50 µM and sensitivity of 0.23 nA/µM were obtained. The heterogeneous electron transfer rate constant K_ct was 1.52±0.22 s^?1 and the apparent Michaelis? Menten constant was calculated to be 0.028 mM. The HRP‐functionalized electrode demonstrated a good reproducibility and long‐term stability.     

Electrochemical Determination of 2‐Nitrophenol in Water Samples Using Mg‐Al‐SDS Hydrotalcite‐Like Clay Modified Glassy Carbon Electrode

A glassy carbon electrode (GCE) modified with Mg‐Al‐SDS hydrotalcite‐like clay (SDS‐HTLC) was used for the sensitive voltammetric determination of 2‐nitrophenol (2‐NP) utilizing the oxidation process. The results indicate the prepared modified electrode has an excellent electrocatalytic activity toward 2‐NP oxidation, lowering the oxidation overpotential and increasing the oxidation current. Under optimal conditions, the oxidation current was proportional to 2‐NP concentration in the range from 1.0×10^?6 to 6.0×10^?4 M with the detection limit of 5.0×10^?7 M by DPV (S/N=3). The fabricated electrode was applied for 2‐NP determination in water samples and the recovery for these samples was from 95.6 to 103.5%.     

Anti‐cancer Herbal Drug Berberine – Sensitive Determination Using Boron‐doped Diamond Electrode

Determination of berberine, an isoquinoline plant alkaloid, with antibacterial, antiparasitic, antifungal, hypotensive and antitumoral effects, was proposed by introducing square wave voltammetry on boron‐doped diamond electrode. At optimized experimental parameters, in Britton‐Robinson buffer solution pH 5 berberine provides 3 oxidation peaks (+0.63; +1.14 and +1.34 V) and one reduction (+0.15 V) (vs. Ag/AgCl electrode), with good repeatability (relative standard deviation of 2.6 % and 1.9 % for 8 measurements at 0.5 and 10 µM concentration level, respectively). Calibration curve was linear in wade linear range from 0.1 to 50 µM with limit of detection of 0.04 µM. The proposed procedure was successfully applied for the determination of berberine in seed extract from Argemone mexicana with satisfactory recovery (102–102.6 %). The developed method may represent a sensitive alternative to highly toxic mercury electrodes, modified electrodes and chromatographic methods.     

Poly(pyridine‐3‐boronic acid)/Multiwalled Carbon Nanotubes Modified Glassy Carbon Electrodes for Simultaneous Determination of Ascorbic Acid, 3,4‐Dihydroxyphenylacetic Acid and Uric Acid

Poly(pyridine‐3‐boronic acid) (PPBA)/multiwalled carbon nanotubes (MWCNTs) composite modified glassy carbon electrode (GCE) was used for the simultaneous determination of ascorbic acid (AA), 3,4‐dihydroxyphenylacetic acid (DOPAC) and uric acid (UA). The anodic peaks for AA, DOPAC and UA at the PPBA/MWCNTs/GCE were well resolved in phosphate buffer solution (pH 7.4). The electrooxidation of AA, DOPAC and UA in the mixture solution was investigated. The peak currents increase with their concentrations increasing. The detection limits (S/N=3) of AA, DOPAC and UA are 5 µM, 3 µM and 0.6 µM, respectively.     

Gold Electrode Modified with Self‐Assembled Monolayer of Cysteamine‐Functionalized MWCNT and Its Application in Simultaneous Determination of Dopamine and Uric Acid

The voltammetric behavior of dopamine (DA) and uric acid (UA) on a gold electrode modified with self‐assembled monolayer (SAM) of cysteamine (CA) conjugated with functionalized multiwalled carbon nanotubes (MWCNTs) was investigated. The film modifier of functionalized SAM was characterized by means of scanning electron microscopy (SEM) and also, electrochemical impedance spectroscopy (EIS) using para‐hydroquinone (PHQ) as a redox probe. For the binary mixture of DA and UA, the voltammetric signals of these two compounds can be well separated from each other, allowing simultaneous determination of DA and UA. The effect of various experimental parameters on the voltammetric responses of DA and UA was investigated. The detection limit in differential pulse voltammetric determinations was obtained as 0.02 µM and 0.1 µM for DA and UA, respectively. The prepared modified electrode indicated a stable behavior and the presence of surface COOH groups of the functionalized MWCNT avoided the passivation of the electrode surface during the electrode processes. The proposed method was successfully applied for the determination of DA and UA in urine samples with satisfactory results. The response of the gold electrode modified with MWCNT‐functionalized SAM method toward DA, UA, and ascorbic acid (AA) oxidation was compared with the response of the modified electrode prepared by the direct casting of MWCNT.     

Electrochemical Determination of the Herbicide Bentazone Using a Carbon Nanotube β‐Cyclodextrin Modified Electrode

An electrochemical sensor has been developed for the determination of the herbicide bentazone, based on a GC electrode modified by a combination of multiwalled carbon nanotubes (MWCNT) with β‐cyclodextrin (β‐CD) incorporated in a polyaniline film. The results indicate that the β‐CD/MWCNT modified GC electrode exhibits efficient electrocatalytic oxidation of bentazone with high sensitivity and stability. A cyclic voltammetric method to determine bentazone in phosphate buffer solution at pH 6.0, was developed, without any previous extraction, clean‐up, or derivatization steps, in the range of 10–80 µmol L^?1, with a detection limit of 1.6 µmol L^?1 in water. The results were compared with those obtained by an established HPLC technique. No statistically significant differences being found between both methods.     

Voltammetric Determination of Uric Acid at a Fullerene‐C60‐Modified Glassy Carbon Electrode

Glassy carbon electrode modified by microcrystals of fullerene‐C₆₀ mediates the voltammetric determination of uric acid (UA) in the presence of ascorbic acid (AA). Interference of AA was overcome owing to the ability of pretreated fullerene‐C₆₀‐modified glassy carbon electrode. Based on its strong catalytic function towards the oxidation of UA and AA, the overlapping voltammetric response of uric acid and ascorbic acid is resolved into two well‐defined voltammetric peaks with lowered oxidation potential and enhanced oxidation currents under conditions of both linear sweep voltammetry (LSV) and Osteryoung square‐wave voltammetry (OSWV). At pH 7.2, a linear calibration graph is obtained for UA in linear sweep voltammetry over the range from 0.5 μM to 700 μM with a correlation coefficient of 0.9904 and a sensitivity of 0.0215 μA μM^?1 . The detection limit (3σ) is 0.2 μM for standard solution. AA in less than four fold excess does not interfere. The sensitivity and detection limit in OSWV were found as 0.0255 μA μM^?1 and 0.12 μM, for standard solution respectively. The presence of physiologically common interferents (i.e. adenine, hypoxanthine and xanthine) negligibly affects the response of UA. The fullerene‐C₆₀‐modified electrode exhibited a stable, selective and sensitive response to uric acid in the presence of interferents.     

Selective and Sensitive Electrochemical Sensor for L‐Methionine at Physiological pH Using Functionalized Triazole Polymer Film Modified Electrode

This communication describes the determination of an essential amino acid, L ‐methionine (L ‐Met) in the presence of important interferents, ascorbic acid (AA) and uric acid (UA) at physiological pH using a glassy carbon electrode modified with an electropolymerized film of 3‐amino‐5‐mercapto‐1,2,4‐triazole (p‐AMTa). The bare glassy carbon electrode fails to show a voltammetric signal for L ‐Met in the presence of AA and UA at pH 7.2. However, the p‐AMTa electrode separates the voltammetric signals of AA, UA and L ‐Met with pronounced oxidation currents. The amperometric current of L ‐Met was increased linearly from 1.0×10^?7 to 1×10^?4 M and the detection limit was found to be 4.12×10^?10 M (S/N=3).     

Voltammetric Determination of Adrenaline Using a Poly(1‐Methylpyrrole) Modified Glassy Carbon Electrode

A voltammetric method using a poly(1‐methylpyrrole) modified glassy carbon electrode was developed for the quantification of adrenaline. The modified electrode exhibited stable and sensitive current responses towards adrenaline. Compared with a bare GCE, the modified electrode exhibits a remarkable shift of the oxidation potentials of adrenaline in the cathodic direction and a drastic enhancement of the anodic current response. The separation between anodic and cathodic peak potentials (ΔEp) for adrenaline is 30 mV in 0.1 M phosphate buffer solution (PBS) at pH 4.0 at modified glassy carbon electrodes. The linear current response was obtained in the range of 7.5 × 10^?7 to 2.0 × 10^?4 M with a detection limit of 1.68 × 10^?7 M for adrenaline by square wave voltammetry. The poly(1‐methypyrrole)/GCE was also effective to simultaneously determine adrenaline, ascorbic acid and uric acid in a mixture and resolved the overlapping anodic peaks of these three species into three well‐defined voltammetric peaks in cyclic voltammetry. The modified electrode has been successfully applied for the determination of adrenaline in pharmaceuticals. The proposed method showed excellent stability and reproducibility.     

Application of a Modified CuO Nanoparticles Carbon Paste Electrode for Simultaneous Determination of Isoperenaline,Acetaminophen and N‐acetyl‐L‐cysteine

A 1‐[2‐hydroxynaphthylazo]‐6‐nitro‐2‐naphthol‐4‐sulfonate/ CuO nanoparticles modified carbon paste electrode (HNNSCCPE) was constructed and the electro‐oxidation of isoprenaline at the surface of the modified electrode was studied using cyclic voltammetry (CV), chronoamperometry (CHA), and square wave voltammetry (SWV). Under the optimized conditions, the square wave voltammetric peak current of isoprenaline increased linearly with isoprenaline concentrations in the range of 1.0×10^?7 to 7.0×10^?4 M and detection limit of 5.0×10^?8 M was obtained for isoprenaline. The prepared modified electrode exhibits a very good resolution between the voltammetric peaks of isoprenaline, acetaminophen and N‐acetyl‐L‐cysteine which makes it suitable for the detection of isoprenaline in the presence of acetaminophen and N‐acetyl‐L‐cysteine in real samples.     

Direct Electrochemical Sensing of Phenazine‐1‐carboxylic Acid Secreted by Pseudomonas chlororaphis subsp. aureofaciens BCRC 11057T Using Disposable Screen‐printed Carbon Electrode

A novel electrochemical approach for direct recognition of antibiotic phenazine‐1‐carboxylic acid (PCA) was developed. PCA was electropolymerized on preanodized screen‐printed carbon electrode (SPCE*‐PCA) through repetitive cyclic voltammetry and characterized by XPS and FESEM. Electron transfer involved intermediate phenomenon of diffusion‐controlled redox process and surface bound redox reaction. At pH 8 (optimum), SPCE*‐PCA had a detection limit of 0.51±0.04 μM, a quantification limit of 1.7±0.13 μM, linearity of up to 50 µM, a repeatability of 15.5 % and a reproducibility of 1.7 %. PCA secreted by Pseudomonas chlororaphis subsp. aureofaciens BCRC 11057^T was investigated successfully using present single run approach.     

N‐(3,4‐Dihydroxyphenethyl)‐3,5‐dinitrobenzamide‐Modified Multiwall Carbon Nanotubes Paste Electrode as a Novel Sensor for Simultaneous Determination of Penicillamine,Uric acid,and Tryptophan

N‐(3,4‐dihydroxyphenethyl)‐3,5‐dinitrobenzamide modified multiwall carbon nanotubes paste electrode was used as a voltammetric sensor for oxidation of penicillamine (PA), uric acid (UA) and tryptophan (TP). In a mixture of PA, UA and TP, those voltammograms were well separated from each other with potential differences of 300, 610, and 310 mV, respectively. The peak currents were linearly dependent on PA, UA and TP concentrations in the range of 0.05–300, 5–420, and 1.0–400 µmol L^?1, with detection limits of 0.021, 2.0, and 0.82 µmol L^?1, respectively. The modified electrode was used for the determination of those compounds in real samples.     

Electrocatalytic Oxidation and Voltammetric Determination of Hydrazine on the Tetrabromo‐p‐Benzoquinone Modified Carbon Paste Electrode

The electrochemical properties of hydrazine studied at the surface of a carbon paste electrode spiked with p‐bromanil (tetrabromo‐p‐benzoquinone) using cyclic voltammetry (CV), double potential‐step chronoamperometry and differential pulse voltammetry (DPV) in aqueous media. The results show this quinone derivative modified carbon paste electrode, can catalyze the hydrazine oxidation in an aqueous buffered solution. It has been found that under the optimum conditions (pH 10.00), the oxidation of hydrazine at the surface of this carbon paste modified electrode occurs at a potential of about 550 mV less positive than that of a bar carbon paste electrode. The electrocatalytic oxidation peak current of hydrazine showed a linear dependent on the hydrazine concentrations and linear analytical curves were obtained in the ranges of 6.00×10^?5 M–8.00×10^?3 M and 7.00×10^?6 M–8.00×10^?4 M of hydrazine concentration with CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 3.6×10^?5 M and 5.2×10^?6 M by CV and DPV methods. This method was also used for the determination of hydrazine in the real sample (waste water of the Mazandaran wood and paper factory) by standard addition method.